CONTROLS -> Driving for Your BMW 5 Series 4 Door 2022

Driving  
CONTROLS  
Driving  
Vehicle features and  
options  
Auto Start/Stop function  
Principle  
This chapter describes all standard, country-spe‐  
cific and optional features offered with the series.  
It also describes features and functions that are  
not necessarily available in your vehicle, e.g., due  
to the selected options or country versions. This  
also applies to safety-related functions and sys‐  
tems. When using these functions and systems,  
the applicable laws and regulations must be ob‐  
served.  
The Auto Start/Stop function helps save fuel.  
The system switches off the engine during a  
stop, for instance in traffic jam or at traffic lights.  
Drive-ready state remains switched on. The en‐  
gine starts automatically for driving off.  
Additional information:  
Coasting, refer to page 318.  
General information  
After each engine start using the Start/Stop but‐  
ton, the Auto Start/Stop function is ready. The  
function is activated from speeds of approx.  
3 mph/5 km/h.  
Start/Stop button  
Principle  
Depending on the selected driving mode, the  
system is automatically activated or deactivated.  
Pressing the Start/Stop button  
switches drive-ready state on or  
off.  
Engine stop  
Steptronic transmission: the  
drive-ready state is switched on  
when you depress the brake pedal while press‐  
ing the Start/Stop button.  
Functional requirements  
Steptronic transmission  
Pressing the Start/Stop button again switches  
the drive-ready state back off and standby state  
is switched back on.  
The engine is switched off automatically during a  
stop under the following conditions:  
The selector lever is in selector lever position  
D.  
Additional information:  
Drive-ready state, refer to page 40.  
Standby state, refer to page 40.  
The brake pedal remains depressed while the  
vehicle is stationary or the vehicle is held by  
Automatic Hold.  
The driver's safety belt is buckled or the driv‐  
er's door is closed.  
Driving away  
1. Turn on drive readiness.  
2. Apply gear position.  
3. Release the parking brake.  
4. Drive away.  
Steptronic transmission: manual  
engine stop  
If the engine was not switched off automatically  
when the vehicle stopped, the engine can be  
switched off manually:  
135  
Online Edition for Part no. 01405A37F46 - VI/21  
Driving  
CONTROLS  
Depress the brake pedal forcefully again from  
the current pedal position.  
The outside temperature is high and auto‐  
matic climate control is running.  
Engage selector lever position P.  
The car's interior has not yet been heated or  
cooled to the required level.  
When all functional preconditions are fulfilled, the  
engine switches off.  
Where there is a risk of window condensation  
when the automatic climate control is  
switched on.  
Air conditioning system when the  
engine is switched off  
The air flow from the air conditioning system is  
reduced when the engine is switched off.  
Engine or other parts not at operating tem‐  
perature.  
Engine cooling is required.  
The wheels are at a sharp angle or the steer‐  
ing wheel is being turned.  
Displays in the instrument cluster  
Vehicle battery is heavily discharged.  
At higher elevations.  
General information  
The display in the instrument  
cluster indicates that the Auto  
Start/Stop function is ready for an  
automatic engine start.  
Hood is unlocked.  
The Automatic Parking Assistant is activated.  
Stop-and-go traffic.  
Steptronic transmission: selector lever posi‐  
tion in N or R.  
The display indicates that the  
conditions for an automatic en‐  
gine stop have not been met.  
After driving in reverse.  
Use of fuel with high ethanol content.  
Starting the engine  
Functional requirements  
Steptronic transmission  
Total time with switched-off engine  
ECO PRO driving mode: depend‐  
ing on the vehicle equipment, the  
total time that the engine has  
The engine starts automatically under the follow‐  
ing preconditions:  
been switched off using the Auto  
Start/Stop function is displayed  
on an automatic engine stop.  
By releasing the brake pedal.  
When Automatic Hold is activated: step on  
the accelerator pedal.  
The total time can be reset via the trip data.  
Additional information:  
ECO PRO, refer to page 316.  
Driving off  
After the engine starts, accelerate as usual.  
Functional limitations  
The engine is not switched off automatically in  
the following situations:  
Safety mode  
After the engine switches off automatically, it will  
not start again automatically if any one of the fol‐  
lowing conditions are met:  
In case of a steep downhill grade.  
Brake not engaged strongly enough.  
136  
Online Edition for Part no. 01405A37F46 - VI/21  
Driving  
CONTROLS  
The driver's safety belt is unbuckled and the  
driver's door is open.  
When a situation is detected in which the  
stopping time is expected to be very short,  
the engine is not switched off automatically.  
A message appears on the Control Display,  
depending on the situation.  
Hood was unlocked.  
Some indicator lights light up for a varied length  
of time.  
When a situation is detected in which the ve‐  
hicle needs to drive off immediately, the en‐  
gine is started automatically.  
The engine can only be started via the Start/Stop  
button.  
The function may be restricted if the navigation  
data is invalid, outdated or not available, for ex‐  
ample.  
System limits  
Even if driving off was not intended, the deacti‐  
vated engine starts up automatically in the fol‐  
lowing situations:  
Activating/deactivating the  
system manually  
In case of excessive warming of the interior  
when air conditioning is turned on.  
In case of excessive cooling of the interior  
when the heating is turned on.  
Principle  
The engine is not automatically switched off.  
In case of a risk of window condensation  
when the automatic climate control is turned  
on.  
The engine is started during an automatic engine  
stop.  
In case of a steering operation.  
Steptronic transmission:  
Without Mild-Hybrid technology: via  
button  
When changing from gear lever position D to  
N or R.  
Steptronic transmission:  
When changing from gear lever position P to  
N, D, or R.  
In case of seriously discharged vehicle bat‐  
tery.  
When starting an oil level measurement.  
Press the button.  
Without Mild-Hybrid technology:  
additional functions Auto Start/  
Stop  
Depending on the vehicle equipment and coun‐  
try-specific version, the vehicle features a variety  
of sensors for assessing the traffic situation. The  
Auto Start/Stop function uses this information to  
adapt to various traffic situations in a proactive  
manner.  
Steptronic transmission: via  
selector lever position  
The Auto Start/Stop function is also deactivated  
in selector lever position M/S.  
Via the Driving Dynamics Control  
The Auto Start/Stop function is also deactivated  
in SPORT driving mode of the Driving Dynamics  
Control.  
For instance, this applies to the following situa‐  
tions:  
137  
Online Edition for Part no. 01405A37F46 - VI/21  
Driving  
CONTROLS  
Without Mild-Hybrid technology:  
display  
Driving Dynamics Control  
LED comes on: auto Start/Stop function is  
deactivated.  
Principle  
The Driving Dynamics Control influences the  
driving dynamics properties of the vehicle.  
LED goes out: auto Start/Stop function is ac‐  
tivated.  
The vehicle can be adjusted depending on the  
situation using various driving modes.  
Switching off the vehicle during  
an automatic engine stop  
General information  
The following systems are affected, for instance:  
Engine characteristics.  
General information  
During an automatic engine stop, the vehicle can  
be switched off permanently, for instance when  
leaving it.  
Steptronic transmission.  
Adaptive chassis.  
Adaptive Drive.  
Steptronic transmission  
1. Press the Start/Stop button.  
Drive-ready state is switched off.  
Standby state is switched on.  
Active roll stabilization.  
Adaptive M chassis.  
Adaptive M Chassis Professional  
Integral Active Steering.  
Display in the instrument cluster.  
Cruise control.  
Selector lever position P is engaged auto‐  
matically.  
2. Set the parking brake.  
Backrest width for comfort seats.  
Automatic deactivation  
General information  
In certain situations, the Auto Start/Stop function  
is deactivated automatically for safety reasons,  
for instance if no driver is detected.  
When the drive-ready state is switched on, the  
COMFORT or ECO PRO driving mode is se‐  
lected automatically, depending on the equip‐  
ment.  
Overview  
Malfunction  
The Auto Start/Stop function no longer switches  
off the engine automatically. A Check Control  
message is displayed. It is possible to continue  
driving. Have the system checked by a dealer's  
service center or another qualified service center  
or repair shop.  
138  
Online Edition for Part no. 01405A37F46 - VI/21  
Driving  
CONTROLS  
SPORT  
Displays in the instrument  
cluster  
Principle  
The selected driving mode is dis‐  
played in the instrument cluster.  
The SPORT driving mode is a dynamic setting  
for more agility with an optimized suspension.  
Turning on  
Press the button repeatedly until  
SPORT is displayed in the instrument  
cluster.  
Driving modes  
Button  
Driving  
mode  
Configuration  
SPORT INDIVIDUAL  
SPORT  
INDIVIDUAL  
Principle  
SPORT  
PLUS  
In the SPORT INDIVIDUAL driving mode, individ‐  
ual settings can be adjusted to support driving  
dynamics properties.  
COMFORT  
ECO PRO  
ADAPTIVE  
INDIVIDUAL  
Configuration  
1. "CAR"  
2. "Settings"  
When the drive-ready state is switched on, the  
COMFORT or ECO PRO driving mode is se‐  
lected automatically, depending on the equip‐  
ment.  
3. "Driving mode"  
4. "SPORT INDIVIDUAL"  
5. Select the desired setting.  
Reset SPORT INDIVIDUAL to the standard set‐  
tings:  
Driving modes in detail  
COMFORT  
"Reset to SPORT STANDARD".  
SPORT PLUS  
Principle  
The COMFORT driving mode is a balanced set‐  
ting between sporty and consumption optimized  
driving.  
Principle  
The SPORT PLUS driving mode is a dynamic  
setting for maximum agility with an adjusted  
drive.  
Turning on  
Press the button repeatedly until COM‐  
FORT is displayed in the instrument  
cluster.  
Turning on  
Press the button repeatedly until  
SPORT PLUS is displayed in the instru‐  
ment cluster.  
139  
Online Edition for Part no. 01405A37F46 - VI/21  
 
Driving  
CONTROLS  
Switching on  
Press the button. ADAPTIVE is dis‐  
ECO PRO  
Concept  
played in the instrument cluster.  
In ECO PRO drive mode, consumption is opti‐  
mized.  
INDIVIDUAL configuration  
General information  
The last individual configuration is activated di‐  
rectly when the driving mode is called up again.  
Turning on  
Press the button repeatedly until ECO  
PRO is displayed in the instrument clus‐  
ter.  
Activating configuration of the drive  
mode  
ECO PRO INDIVIDUAL  
Press the button for the desired drive mode sev‐  
eral times.  
Principle  
In the ECO PRO INDIVIDUAL driving mode, indi‐  
vidual settings can be adjusted to support an  
economical driving style.  
Parking brake  
The engine control and comfort features, for in‐  
stance the climate control output, are adjusted.  
Principle  
The parking brake is used to prevent the vehicle  
from rolling when it is parked.  
Configuration  
1. "CAR"  
2. "Settings"  
Safety information  
3. "Driving mode"  
4. "ECO PRO INDIVIDUAL"  
5. Select the desired setting.  
Warning  
An unsecured vehicle can begin to move and  
possibly roll away. There is a risk of accident.  
Before exiting, secure the vehicle against roll‐  
ing.  
Reset ECO PRO INDIVIDUAL to the standard  
settings:  
"Reset to ECO PRO STANDARD".  
In order to ensure that the vehicle is secured  
against rolling away, follow the following:  
ADAPTIVE  
▷ Set the parking brake.  
Principle  
▷ On uphill grades or on a downhill slope,  
turn the front wheels in the direction of the  
curb.  
The ADAPTIVE driving mode is a balanced driv‐  
ing mode that automatically adapts to the driving  
situation and driving style.  
▷ On uphill grades or on a downhill slope,  
also secure the vehicle, for instance with a  
wheel chock.  
If the navigation system is active, upcoming road  
sections are considered.  
140  
Online Edition for Part no. 01405A37F46 - VI/21  
 
Driving  
CONTROLS  
While driving  
Warning  
General information  
Unattended children or animals in the vehicle  
can cause the vehicle to move and endanger  
themselves and traffic, for instance due to the  
following actions:  
To use as emergency brake while driving.  
Pull the switch and hold it. The vehicle  
brakes hard while the switch is being  
pulled.  
▷ Pressing the Start/Stop button.  
▷ Releasing the parking brake.  
The indicator light in the instrument clus‐  
ter illuminates red, a signal sounds, and  
the brake lights illuminate.  
▷ Opening and closing the doors or win‐  
dows.  
▷ Engaging selector lever position N.  
▷ Using vehicle equipment.  
A Check Control message is displayed.  
The parking brake is engaged when the vehicle  
is stationary.  
There is a risk of accidents or injuries. Do not  
leave children or animals unattended in the ve‐  
hicle. Take the vehicle key with you when exit‐  
ing and lock the vehicle.  
With Emergency Stop Assistant  
Pull the switch briefly to activate the emer‐  
gency stop function.  
Overview  
Additional information:  
Emergency Stop Assistant, refer to page 207.  
Releasing  
Releasing manually  
1. Turn on drive readiness.  
2.  
Steptronic transmission: press the  
switch while the brake is pressed or selector  
lever position P is set.  
Parking brake  
The LED and indicator light turn off.  
The parking brake is released.  
Setting  
With a stationary vehicle  
Automatic release  
Pull the switch.  
The parking brake is released automatically  
when you drive away.  
The LED lights up.  
The LED and indicator light turn off.  
The indicator light in the instrument clus‐  
ter illuminates red. The parking brake is  
set.  
141  
Online Edition for Part no. 01405A37F46 - VI/21  
Driving  
CONTROLS  
Steptronic transmission:  
Automatic Hold  
Warning  
Unattended children or animals in the vehicle  
can cause the vehicle to move and endanger  
themselves and traffic, for instance due to the  
following actions:  
Principle  
Automatic Hold assists the driver by automati‐  
cally setting and releasing the brake, such as  
when moving in stop-and-go traffic.  
▷ Pressing the Start/Stop button.  
▷ Releasing the parking brake.  
The vehicle is automatically held in place when it  
is stationary.  
▷ Opening and closing the doors or win‐  
dows.  
On uphill grades the system prevents the vehicle  
from rolling back when driving off.  
▷ Engaging selector lever position N.  
▷ Using vehicle equipment.  
General information  
Under the following conditions, the parking brake  
is automatically engaged:  
There is a risk of accidents or injuries. Do not  
leave children or animals unattended in the ve‐  
hicle. Take the vehicle key with you when exit‐  
ing and lock the vehicle.  
Drive-ready state is switched off.  
The driver's door is opened while the vehicle  
is stationary.  
NOTICE  
The moving vehicle is brought to a standstill  
using the parking brake.  
If the vehicle is stationary, Automatic Hold en‐  
gages the parking brake and prevents the vehi‐  
cle from rolling in a car wash. There is a risk of  
damage to property, among other potential  
damage. Deactivate Automatic Hold prior to  
entering the car wash.  
Safety information  
Warning  
An unsecured vehicle can begin to move and  
possibly roll away. There is a risk of accident.  
Before exiting, secure the vehicle against roll‐  
ing.  
Overview  
In order to ensure that the vehicle is secured  
against rolling away, follow the following:  
▷ Set the parking brake.  
▷ On uphill grades or on a downhill slope,  
turn the front wheels in the direction of the  
curb.  
▷ On uphill grades or on a downhill slope,  
also secure the vehicle, for instance with a  
wheel chock.  
Automatic Hold  
142  
Online Edition for Part no. 01405A37F46 - VI/21  
 
Driving  
CONTROLS  
The LED goes out.  
Establishing operational readiness  
of Automatic Hold  
1. Turn on drive readiness.  
The indicator light goes out.  
2.  
Press the button.  
The LED lights up.  
Automatic Hold is switched off.  
If the vehicle is being held by Automatic Hold,  
press additionally on the brake pedal, when  
switching off.  
The indicator light lights up green.  
Automatic Hold is functional.  
After every vehicle restart, the last se‐  
lected setting is active.  
Malfunction  
If the parking brake fails or in case of a fault, se‐  
cure the vehicle against rolling before exiting.  
Automatic Hold holding the vehicle  
A Check Control message is displayed.  
Operational readiness is established and the  
driver's door is closed.  
Secure the vehicle against rolling away, for in‐  
stance with a wheel chock, after exiting the vehi‐  
cle.  
After the brake is applied, the vehicle is  
kept from rolling as soon as the indicator  
light illuminates green.  
After a power interruption  
To reestablish parking brake functionality after a  
power interruption:  
Driving off  
Press the accelerator pedal to drive off.  
1. Turn on standby state.  
The brake is released automatically and the indi‐  
cator light of the parking brake is no longer illumi‐  
nated.  
2.  
Pull the switch while stepping on the  
brake pedal or selector lever position P is set  
and then push.  
Activating the parking brake  
automatically  
The parking brake is automatically set if drive-  
ready state is switched off while the vehicle is  
being held by Automatic Hold or if the vehicle is  
exited.  
This process may take a few seconds. Some  
mechanical sounds associated with this process  
are normal.  
The indicator light is no longer illumi‐  
nated as soon as the parking brake is  
ready for operation again.  
The indicator light changes from green  
to red.  
Turn signal  
The parking brake is not set automatically, if the  
drive-ready state is switched off, while the vehi‐  
cle is coasting to a halt. Automatic Hold is deacti‐  
vated.  
Turn signal in exterior mirror  
When driving and during operation of the turn  
signals or hazard warning system, do not fold in  
the exterior mirrors, so that the signal lights on  
the exterior mirror are easy to see.  
Switching operational readiness off  
Press the button.  
143  
Online Edition for Part no. 01405A37F46 - VI/21  
Driving  
CONTROLS  
The high beams light up when the low beams  
are switched on.  
Blinking  
High beams off/headlight flasher, arrow 2.  
Window wiper system  
General information  
Do not use the wipers if the windshield is dry, as  
this may damage the wiper blades or cause them  
to become worn more quickly.  
Press the lever past the resistance point.  
Safety information  
Triple turn signal activation  
Lightly tap the lever up or down.  
Warning  
The triple turn signal duration can be adjusted.  
If the wipers start moving in the folded away  
state, body parts can be jammed or damage  
may occur to parts of the vehicle. There is a risk  
of injury or risk of damage to property. Make  
sure that the vehicle is switched off when the  
wipers are in the folded away state and the wip‐  
ers are folded in when switching on.  
1. "CAR"  
2. "Settings"  
3. "Exterior lighting"  
4. "One-touch turn signal"  
5. Select the desired setting.  
Brief blinking  
Press the lever to the resistance point and hold it  
there for as long as you want the turn signal to  
flash.  
NOTICE  
If the wipers are frozen to the windshield, the  
wiper blades can be torn off and the wiper mo‐  
tor can overheat when switching on. There is a  
risk of damage to property, among other poten‐  
tial damage. Defrost the windshield prior to  
switching the wipers on.  
High beams,  
headlight flasher  
Press the lever forward or pull it backward.  
Turn on window wiper system  
High beams on, arrow 1.  
144  
Online Edition for Part no. 01405A37F46 - VI/21  
Driving  
CONTROLS  
Press the lever up until the desired position is  
reached.  
Safety information  
Resting position of the wipers, position 0.  
Rain sensor, position 1.  
NOTICE  
If the rain sensor is activated, the wipers can  
accidentally start moving in vehicle washes.  
There is a risk of damage to property, among  
other potential damage. Deactivate the rain  
sensor in vehicle washes.  
Normal wiper speed, position 2.  
Fast wiper speed, position 3.  
When the journey is interrupted with the window  
wiper system turned on: when the journey con‐  
tinues, the wipers resume at their previous  
speed.  
Activate rain sensor  
Turn off the window wiper  
system and flick wipe  
Press the lever up once from its 0 position, ar‐  
row 1.  
Wiping operation is started.  
Press the lever down.  
The LED in the wiper lever is illuminated.  
Turn off: press the lever down until it reaches  
the 0 position.  
In frosty conditions, wiping operation may not  
start.  
Flick wipe: press the lever down from the 0  
position.  
Deactivate rain sensor  
Press the lever back into the 0 position.  
The lever automatically returns to its 0 posi‐  
tion when released.  
Adjusting the rain sensor sensitivity  
Rain sensor  
Principle  
The rain sensor automatically controls the time  
between wipes depending on the intensity of the  
rainfall.  
General information  
The sensor is located on the windshield, directly  
in front of the interior mirror.  
Turn the thumbwheel to adjust the sensitivity of  
the rain sensor.  
145  
Online Edition for Part no. 01405A37F46 - VI/21  
Driving  
CONTROLS  
Upward: high rain sensor sensitivity.  
Downward: low rain sensor sensitivity.  
Fold-away position of the wipers  
Principle  
In the fold-out position, the wipers can be folded  
out from the windshield, which is important, for  
instance, when changing the wiper blades or for  
folding away under frosty conditions.  
Windshield washer system  
Safety information  
Warning  
Safety information  
The washer fluid can freeze onto the window at  
low temperatures and obstruct the view. There  
is a risk of accident. Only use the washer sys‐  
tems, if the washer fluid cannot freeze. Use  
washer fluid with antifreeze, if needed.  
Warning  
If the wipers start moving in the folded away  
state, body parts can be jammed or damage  
may occur to parts of the vehicle. There is a risk  
of injury or risk of damage to property. Make  
sure that the vehicle is switched off when the  
wipers are in the folded away state and the wip‐  
ers are folded in when switching on.  
NOTICE  
When the washer fluid reservoir is empty, the  
wash pump cannot work as intended. There is  
a risk of damage to property, among other po‐  
tential damage. Do not use the washer system  
when the washer fluid reservoir is empty.  
NOTICE  
If the wipers are frozen to the windshield, the  
wiper blades can be torn off and the wiper mo‐  
tor can overheat when switching on. There is a  
risk of damage to property, among other poten‐  
tial damage. Defrost the windshield prior to  
switching the wipers on.  
Cleaning the windshield  
Pull the lever.  
The system sprays washer fluid on the wind‐  
shield and activates the wipers briefly.  
Windshield washer nozzles  
The windshield washer nozzles are automatically  
heated while standby state is switched on.  
146  
Online Edition for Part no. 01405A37F46 - VI/21  
Driving  
CONTROLS  
Folding out the wipers  
Safety information  
1. Turn on standby state.  
2. Press and hold the wiper lever down, until the  
wipers stop in a close to vertical position.  
Warning  
An unsecured vehicle can begin to move and  
possibly roll away. There is a risk of accident.  
Before exiting, secure the vehicle against roll‐  
ing, for instance with the parking brake.  
Selector lever positions  
Gear position D  
Selector lever position for normal driving. All  
gears for forward travel are activated automati‐  
cally.  
3. Fold the wipers all the way out from the wind‐  
shield.  
R is reverse  
Engage selector lever position R only when the  
vehicle is stationary.  
Neutral N  
The vehicle may be pushed or roll without power,  
for instance in vehicle washes in selector lever  
position N.  
Folding down the wipers  
Parking position P  
1. Fold the wipers back down onto the wind‐  
shield.  
General information  
Selector lever position, for instance for parking  
the vehicle. The transmission blocks the individ‐  
ual wheels in selector lever position P.  
2. Switch on standby state and press and hold  
the wiper lever down again.  
Wipers return to their resting position and are  
ready again for operation.  
Engage selector lever position P only when the  
vehicle is stationary.  
P is engaged automatically  
Steptronic transmission  
Selector lever position P is engaged automati‐  
cally in situations such as the following:  
Principle  
The Steptronic transmission combines the func‐  
tions of an automatic transmission with the pos‐  
sibility of manual shifting, if needed.  
147  
Online Edition for Part no. 01405A37F46 - VI/21  
Driving  
CONTROLS  
After the drive-ready state is switched off and  
selector lever position R, D or M/S is en‐  
gaged.  
1. Fasten driver's safety belt.  
2. Press and hold the button to release the se‐  
lector lever lock.  
After the standby state has been turned off  
when selector lever position N is engaged.  
If the driver's safety belt is unbuckled, the  
driver's door is opened, and the brake pedal  
is not pressed while the vehicle is stationary  
and selector lever position D, M/S or R is en‐  
gaged.  
Before exiting the vehicle, make sure that selec‐  
tor lever position P is set. Otherwise, the vehicle  
may begin to move. Also set parking brake.  
3. Push the selector lever in the desired direc‐  
tion, past a resistance point, if needed. The  
selector lever automatically returns to the  
center position when released.  
Additional information:  
Parking brake, refer to page 140.  
Engaging selector lever  
positions  
General information  
To prevent the vehicle from creeping after you  
select a gear position, maintain pressure on the  
brake pedal until you are ready to start.  
Functional requirements  
Only when the drive-ready state is switched on  
and the brake pedal is depressed is it possible to  
change from selector lever position P to another  
selector lever position.  
Engaging selector lever position P  
The selection lever position P cannot be  
changed until all technical requirements are met.  
Engaging selector lever position D,  
N, R  
A selector lever lock prevents the following faulty  
operation:  
Press button P.  
Unintentional shifting into selector lever posi‐  
tion R.  
Unintentional shifting from selector lever po‐  
sition P into another selector lever position.  
148  
Online Edition for Part no. 01405A37F46 - VI/21  
Driving  
CONTROLS  
Rolling or pushing the vehicle  
General information  
Sport program M/S  
Principle  
In some situations, the vehicle is to roll without  
its own power for a short distance, for instance in  
a car wash, or be pushed.  
The shifting points and shifting times in the  
Sport program are designed for sportier han‐  
dling. The transmission, for instance shifts up  
later and the shifting times are shorter.  
Engaging selector lever position N  
Activating the Sport program  
NOTICE  
Selector lever position P is automatically en‐  
gaged when standby state is switched off.  
There is a risk of damage to property, among  
other potential damage. Do not switch standby  
state off in car washes.  
1. Switch on drive-ready state while pressing on  
the brake pedal.  
Press the selector lever to the left from selector  
lever position D.  
2. If necessary, release the parking brake.  
3. If necessary, switch off Automatic Hold.  
Automatic Hold, refer to page 142.  
4. Depress the brake pedal.  
The engaged gear is displayed in the instrument  
cluster, for instance S1.  
The sport program of the transmission is acti‐  
vated.  
5. Touch the selector lever lock and engage se‐  
lector lever position N.  
6. Switch off drive-ready state.  
Ending the Sport program  
Press the selector lever to the right.  
D is displayed in the instrument cluster.  
In this way, standby state remains switched  
on, and a Check Control message is dis‐  
played.  
The vehicle can roll.  
Manual mode M/S  
Selector lever position P is engaged automati‐  
cally after approximately 35 minutes.  
Principle  
If there is a malfunction, you may not be able to  
change the selector lever position.  
Manual gear-shifting is possible in manual mode.  
Electronically unlock the transmission lock, if  
needed.  
Kickdown  
Kickdown is used to achieve maximum driving  
performance.  
Step on the accelerator pedal beyond the resist‐  
ance point at the full throttle position.  
149  
Online Edition for Part no. 01405A37F46 - VI/21  
Driving  
CONTROLS  
D is displayed in the instrument cluster.  
Shift paddles  
Activating manual mode  
1. Press the selector lever to the left from selec‐  
tor lever position D, arrow 1.  
Principle  
The shift paddles on the steering wheel allow  
you to shift gears quickly while keeping both  
hands on the steering wheel.  
General information  
Shifting  
The vehicle only shifts at suitable RPM and road  
speeds.  
2. Press the selector lever forward or pull it  
backward, arrows 2.  
Manual mode becomes active and the gear is  
changed.  
Short-term manual mode  
In selector lever position D, actuating a shift pad‐  
dle switches into manual mode temporarily.  
The engaged gear is displayed in the instrument  
cluster, for instance M1.  
After conservative driving in manual mode with‐  
out acceleration or shifting via the shift paddles  
for a certain amount of time, the transmission  
switches back to automatic mode.  
Shifting  
To shift down: press the selector lever for‐  
ward.  
It is possible to switch into automatic mode:  
To shift up: pull the selector lever rearwards.  
Keep the right shift paddle pulled until D is  
displayed in the instrument cluster.  
The transmission continues shifting automati‐  
cally in certain situations, for instance when RPM  
limits are reached.  
In addition to the pulled right shift paddle, pull  
the left shift paddle.  
Steptronic Sport transmission:  
prevent automatic upshifting in M/S  
manual mode  
Depending on the motorization: if driving mode  
SPORT is selected, the Steptronic Sport trans‐  
mission does not automatically upshift in M/  
S manual mode once the maximum speed is  
reached.  
Continuous manual mode  
In selector lever position S, actuating a shift pad‐  
dle switches into manual mode permanently.  
Steptronic Sport transmission  
With the appropriate transmission version, the  
lowest possible gear can be selected by simulta‐  
neously activating kickdown and operating the  
left shift paddles. This is not possible in short-  
term manual mode.  
In addition, there is no downshifting for kick‐  
down.  
Additional information:  
SPORT, refer to page 139.  
Ending the manual mode  
Press the selector lever to the right.  
150  
Online Edition for Part no. 01405A37F46 - VI/21  
Driving  
CONTROLS  
Shifting  
Without Mild-Hybrid technology:  
engage selector lever position N  
Unlocking is possible, if the starter can crank the  
engine.  
1. Press and hold down brake pedal.  
2. Press the Start/Stop button. The starter must  
audibly start. Hold the Start/Stop button  
pressed.  
3. With your free hand, press the button on the  
selector lever, arrow 1, and press the selector  
lever into selector lever position N and hold,  
arrow N, until selector lever position N is dis‐  
played in the instrument cluster.  
Shifting up: pull the right shift paddle.  
Shifting down: pull left shift paddle.  
Downshifting to the lowest possible gear:  
keep the left shift paddle pulled.  
A Check Control message is displayed.  
The selected gear is briefly displayed in the in‐  
strument cluster, followed by the current gear.  
Displays in the instrument  
cluster  
The selector lever position is dis‐  
played, for example P.  
4. Release Start/Stop button and selector lever.  
5. Release brake, as soon as the starter stops.  
Electronic unlocking of the  
transmission lock  
6. Maneuver the vehicle from the hazardous  
area and secure it against rolling away.  
Additional information:  
General information  
Tow-starting/towing, refer to page 378.  
Electronically unlock the transmission lock to  
maneuver vehicle from a hazardous area.  
With Mild-Hybrid technology:  
engage selector lever position N  
1. Press and hold down brake pedal.  
Before unlocking the transmission lock, set the  
parking brake to prevent the vehicle from rolling  
away.  
2. Press and hold the Start/Stop button.  
In vehicles with Mild-Hybrid technology and cor‐  
responding vehicle battery, the action steps for  
unlocking the transmission vary.  
3. With your free hand, press the button on the  
selector lever, arrow 1, and press the selector  
lever into selector lever position N and hold,  
arrow N, until selector lever position N is dis‐  
played in the instrument cluster.  
Additional information:  
Vehicle battery, refer to page 370.  
151  
Online Edition for Part no. 01405A37F46 - VI/21  
Driving  
CONTROLS  
A Check Control message is displayed.  
Start with launch control  
1. Turn on drive readiness.  
2.  
Press the button.  
TRACTION is displayed in the instrument  
cluster and the indicator light for DSC OFF  
lights up.  
3. Engage selector lever position S.  
4. With the left foot, forcefully press down on  
the brake.  
4. Release Start/Stop button and selector lever.  
5. Release the brake.  
5. Press and hold down the accelerator pedal  
beyond the resistance point at the full throttle  
position, kickdown.  
6. Maneuver the vehicle from the danger area  
and secure it against moving on its own.  
A destination flag is displayed in the instru‐  
ment cluster.  
Additional information:  
Tow-starting/towing, refer to page 378.  
6. The starting engine speed adjusts. Wait  
briefly until the engine speed is constant.  
Keep the accelerator pedal in this position.  
Launch Control  
Principle  
7. Release the brake within 3 seconds after the  
destination flag illuminates.  
Launch Control enables optimum acceleration  
on roads with good traction under dry surround‐  
ing conditions.  
The vehicle accelerates.  
Upshifting occurs automatically as long as the  
destination flag is displayed and the accelera‐  
tor pedal is not released.  
General information  
The use of Launch Control causes premature  
component wear since this function represents a  
very heavy load for the vehicle.  
Repeated use during a trip  
After Launch Control has been used, the trans‐  
mission must cool down for approx. 5 minutes  
before Launch Control can be used again.  
Launch Control adjusts to the surrounding con‐  
ditions, when used again.  
Do not use Launch Control during the break-in.  
Do not steer the steering wheel when driving off  
with Launch Control.  
Additional information:  
After using Launch Control  
To increase driving stability, activate DSC Dy‐  
namic Stability Control again as soon as possible.  
Breaking-in period, refer to page 310.  
Functional requirement  
Launch Control is available when the engine is at  
operating temperature. The engine is at operat‐  
ing temperature after an uninterrupted trip of at  
least 6 miles/10 km.  
System limits  
An experienced driver may be able to achieve  
better acceleration values in DSC OFF mode.  
152  
Online Edition for Part no. 01405A37F46 - VI/21