Keys, Doors, and Windows -> Doors for Your Chevrolet Silverado 1500 Light Truck 2023

Keys, Doors, and Windows  
21  
When the safety lock is enabled, adults and  
older children will not be able to open the  
rear door from the inside. Cancel the safety  
locks to enable the doors to open from the  
inside.  
Use the key to unlock the tailgate.  
Open the tailgate by lifting up on its handle  
while pulling the tailgate down.  
To shut the tailgate, firmly push it upward  
until it latches.  
To cancel the safety lock:  
After closing the tailgate, pull it back to be  
sure it is latched securely.  
1. Unlock the door and open it from the  
outside.  
Some tailgates have an electric latch. If the  
battery is disconnected or has low voltage,  
the tailgate will not open. The tailgate will  
resume operation when the battery is  
reconnected or recharged.  
2. Move the lever up to unlock. Do the  
same for the other door.  
Doors  
The safety lock is on the inside edge of the  
rear doors. To use the safety lock:  
Tailgate  
Power Release Tailgate  
1. Move the lever down to the lock  
position.  
Manual Tailgate  
Warning  
{
2. Close the door.  
Make sure there is no one in the way of  
the power tailgate as it is opening and  
closing, and keep hands away from the  
tailgate hinges when in use. You or  
others could be injured if caught in the  
path of the power tailgate or tailgate  
hinges.  
Warning  
{
3. Do the same for the other rear door.  
It is extremely dangerous to ride on the  
tailgate, even when the vehicle is  
To open a rear door when the safety lock  
is on:  
operated at low speeds. People riding on  
the tailgate can easily lose their balance  
and fall in response to vehicle maneuvers.  
Falling from a moving vehicle may result  
in serious injuries or death. Do not allow  
people to ride on the tailgate. Be sure  
everyone in your vehicle is in a seat and  
using a seat belt properly.  
1. Unlock the door by activating the inside  
handle, by pressing the power door  
unlock switch, or by using the  
remote key.  
2. Open the door from the outside.  
22  
Keys, Doors, and Windows  
Caution  
assistance is required. If equipped with  
Keyless Access, a locked tailgate can be  
opened if the remote key is within  
1 m (3 ft).  
To avoid damage to the tailgate, make  
sure the area behind the tailgate is clear  
before opening it.  
To close the tailgate, firmly push it upward  
until it latches. Pull it back to be sure it is  
latched securely.  
In the case of a dead battery, the tailgate  
can be opened manually. Contact your  
dealer or Roadside Assistance.  
Power Tailgate  
If equipped, to lock or unlock the tailgate,  
use the remote key or the key. See Remote  
Key Operation 0 12.  
Warning  
{
Make sure there is no one in the way of  
the power tailgate as it is opening and  
closing, and keep hands away from the  
tailgate hinges when in use. You or  
others could be injured if caught in the  
path of the power tailgate or tailgate  
hinges.  
The vehicle must be in P (Park).  
To open the tailgate:  
.
Press 5 on the center stack.  
.
Press x twice quickly on the remote  
key until the tailgate moves.  
Caution  
To avoid damage to the tailgate, make  
sure the area behind the tailgate is clear  
before opening it.  
If equipped with a power open/close  
tailgate, the tailgate can be opened or  
closed in several ways. To open the tailgate,  
do one of the following:  
.
Press the touch pad on the tailgate  
handle after unlocking all doors. Use the  
top of the tailgate to pull against if  
Keys, Doors, and Windows  
23  
.
Press the touch pad on the tailgate  
handle.  
.
Press x twice quickly on the remote  
key until the tailgate moves. See Remote  
Key Operation 0 12. If equipped with  
Keyless Access, a locked tailgate can be  
opened if the remote key is within  
1 m (3 ft).  
A chime sounds and the taillamps flash  
during the closing operation. If the warning  
chime is not functioning, the tailgate will  
not power close. Power opening is still  
enabled. See your dealer for service.  
The power tailgate may be temporarily  
disabled after repeated power cycling over a  
short period of time. If this occurs, the  
tailgate can still be operated manually.  
The vehicle must be in P (Park) to operate  
the power tailgate. If the vehicle is shifted  
out of P (Park) while the power function is  
in progress, the tailgate will continue to  
completion. If the vehicle is accelerated  
while the tailgate is still closing, the tailgate  
may stop and reverse direction. Make sure  
the tailgate is closed and latched before  
driving.  
.
Press the touch pad on the tailgate  
handle after unlocking all doors.  
To close the tailgate, do one of the  
following:  
.
Press x on the remote key once, then  
quickly press and hold x until the  
.
Press 5 on the center stack.  
tailgate completely closes. If x is  
released prior to it being fully closed, the  
tailgate will reopen.  
.
Press and hold 5 on the center stack  
until the tailgate is fully closed. If 5  
is released prior to the tailgate being  
fully closed, it will reopen. A chime will  
sound when the tailgate is fully closed.  
24  
Keys, Doors, and Windows  
Lift-to-Close Operation  
If the tailgate encounters multiple obstacles,  
the power function will deactivate. After  
removing the obstructions, manually close  
the tailgate to resume normal power  
operation.  
Caution  
To avoid damage to the tailgate, make  
sure the area behind the tailgate is clear  
before opening it.  
Manual Operation  
Caution  
The tailgate can be manually closed from  
the full-open position when the tailgate is  
lifted in a continuous motion. If the tailgate  
motion is stopped between the full-open  
and half-closed positions, the lift-to-close  
feature can engage and power close the  
tailgate. If the touch pad is pressed during  
power operation, the tailgate will stop and  
allow manual operation. The tailgate must  
be held after stopping, or it will continue  
to open.  
To avoid damage to the tailgate, check  
the top surface of the bumper, as well as  
any spaces between the tailgate,  
additional tailgate hinges, and the body  
of the vehicle before using the tailgate.  
Debris or objects can become pinched as  
the tailgate is operated and damage the  
system.  
To close the tailgate using the lift-to-close  
feature, lift the tailgate from the full-open  
position to at least 10 cm (4 in) and hold it  
momentarily. Then, the tailgate will start  
closing automatically. If the tailgate is lifted  
more than halfway between open and close,  
then it will not close automatically.  
If equipped with this feature, the vehicle  
must be in P (Park).  
MultiFlex Tailgate  
Warning  
{
Obstacle Detection  
Make sure there is no one in the way of  
the power tailgate as it is opening and  
closing, and keep hands away from the  
tailgate hinges when in use. You or  
others could be injured if caught in the  
path of the power tailgate or tailgate  
hinges.  
If the tailgate encounters an obstacle during  
a power open cycle, it will stop on the  
obstacle. After removing the obstruction, the  
tailgate can be allowed to open. If the  
tailgate encounters an obstacle during the  
closing cycle, it will stop and reverse to  
full open.  
Keys, Doors, and Windows  
25  
.
Press x twice quickly on the remote  
key until the tailgate moves. See Remote  
Key Operation 0 12. If equipped with  
Keyless Access, the tailgate can be  
opened if the remote key is within  
1 m (3 ft).  
Switches in the inner tailgate prevent the  
primary tailgate from being opened when  
the inner tailgate is not fully closed.  
To open the inner tailgate, press the upper  
touch pad on the tailgate handle after  
unlocking all doors. Pull the top of the  
tailgate to open.  
To open the primary tailgate:  
.
.
Press 5 on the center stack.  
Press the lower touch pad on the tailgate  
handle after unlocking all doors. Use the  
top of the tailgate to pull against if  
assistance is required.  
To close the primary tailgate, firmly push it  
upward until it latches. Pull it back to be  
sure it is latched securely.  
26  
Keys, Doors, and Windows  
Caution  
can still be operated like a traditional  
tailgate, but the inner gate will not be able  
to be opened alone.  
MultiFlex Inner Tailgate Enable/Disable  
Do not open the inner tailgate with the  
primary tailgate open if there is a hitch  
ball or trailer attached. This may damage  
the tailgate.  
To enable the inner tailgate function, hold  
the upper touchpad on the handle for  
3 seconds until the tail lamps flash. The  
inner tailgate can now be opened separately  
from the outer tailgate.  
To close the inner tailgate with the primary  
tailgate closed, firmly push or pull it upward  
until it latches. Pull it back to be sure it is  
latched securely.  
Tailgate Step  
Warning  
{
To close the inner tailgate with the primary  
tailgate open:  
To avoid personal injury, keep hands  
away from the hinges when operating  
the tailgate step.  
.
Hold the primary tailgate and firmly close  
the inner tailgate.  
The MultiFlex inner tailgate may be  
equipped with an enable/disable feature to  
prevent the inner tailgate from being  
opened when a hitch or other equipment is  
installed that could damage the inner  
tailgate.  
.
Raise the inner tailgate so it meets the  
primary tailgate and close together at the  
same time.  
With the primary and inner tailgates open,  
the tailgate step can be lowered to access  
the pickup bed.  
When using the tailgate step as a load stop,  
the load must be secured as the load could  
shift. See Cargo Tie-Downs 0 96.  
Using the Step  
To disable the inner tailgate from opening:  
ensure that the remote key is within  
1 meter (3 ft) of the rear bumper and then  
hold the upper touchpad on the tailgate  
handle for three seconds. The tail lamps will  
flash to alert you that the inner gate has  
been disabled. The inner and outer tailgate  
Caution  
When using the tailgate as a step, the  
load rating is 170 kg (375 lb), which  
includes a person and cargo. Overloading  
the tailgate step can cause damage to  
the tailgate system.  
Keys, Doors, and Windows  
27  
The assist handle helps with entering the  
pickup box. To use:  
1. Lift up on the handle until it locks in the  
open position.  
2. To return the assist handle, pull the  
release lever toward the ball end of the  
handle and push the handle back to the  
closed position.  
Applying Loads to Tailgates  
Caution  
Do not put ramp loads on the inner  
tailgate alone. Damage to the inner  
tailgate may occur.  
.
.
To lower the tailgate step, press the  
button at the center of the step. Make  
sure it lowers to the fully open position.  
To close the tailgate step, lift it firmly.  
Make sure that both side latches are  
engaged.  
Do not place a load on top of the step when  
using it as a load stop.  
Using the Assist Handle  
Preferred Method  
28  
Keys, Doors, and Windows  
Transporting Items That Can  
Catch Fire  
Power Assist Steps  
Warning  
{
Warning  
{
To avoid personal injury or property  
damage, before entering or exiting the  
vehicle, be sure the power assist step is  
fully extended. Do not step on the power  
assist step while it is moving. Never place  
hands or other body parts between the  
extended power assist step and the  
vehicle.  
To avoid personal injury and/or vehicle  
damage when transporting items that  
can catch fire, such as leaves, mulch, hay,  
or cardboard, in the truck bed:  
.
Make sure items are securely  
contained inside the truck bed. Never  
allow them to hang over the sides or  
fall in between the truck bed and  
the cab.  
Alternate Method  
If equipped, the power assist steps, when  
enabled, will extend when the door is  
opened. They will retract three seconds after  
the door is closed or immediately if the  
vehicle starts moving.  
When applying any load to the tailgate,  
distribute the weight evenly across the  
width of the tailgate. This applies to all  
tailgate types.  
.
Never place items between the cab  
and the truck bed. They could touch  
hot exhaust parts and ignite.  
.
Use a load-distributing member (1).  
Secure the ramp to the bumper (2).  
Keep hands, children, pets, objects, and  
clothing clear of the power assist steps  
when in motion.  
.
Warning  
{
Keep cigarettes, sparks, and other ignition  
sources away from the area between the  
bed of the truck and cab. They could fall  
onto the fuel system below and start a  
fire. You or others could be injured and/  
or the vehicle damaged.  
The steps will reverse direction if there is an  
obstruction. If possible, carefully remove the  
obstruction, then open and close the door  
on the same side to complete the motion.  
If the obstruction is not cleared, the assist  
steps remain extended.  
Slight movement of the steps while  
extended is normal.  
Keys, Doors, and Windows  
29  
Kick Switch  
Cleaning  
Off : Alarm system is disarmed.  
The power assist steps can be extended or  
retracted for cleaning. To view available  
settings from the infotainment screen, touch  
Settings > Vehicle > Remote Lock, Unlock,  
Start.  
On Solid : Vehicle is secured during the  
delay to arm the system.  
Fast Flash : Vehicle is unsecured. A door or  
the hood is open.  
Slow Flash : Alarm system is armed.  
Vehicle Security  
This vehicle has theft-deterrent features;  
however, they do not make the vehicle  
impossible to steal.  
Arming the Alarm System  
1. Turn off the vehicle.  
2. Lock the vehicle in one of two ways:  
.
Use the remote key.  
.
With a door open, press Q on the  
interior of the door.  
Vehicle Alarm System  
1. Place the vehicle in P (Park) and unlock  
the doors.  
3. After 30 seconds, the alarm system will  
arm and the indicator light will begin to  
slowly flash. Pressing Q on the remote  
key a second time will bypass the  
30-second delay and immediately arm  
the alarm system.  
2. Kick the switch to extend the power  
assist step to the tire. A Driver  
Information Center (DIC) message  
displays.  
3. Kick the switch again to return to normal  
operation.  
The vehicle alarm system will not arm if the  
doors are locked with the key.  
Enable/Disable  
The power assist steps can be enabled or  
disabled. To view available settings from the  
infotainment screen, touch Settings >  
Vehicle > Remote Lock, Unlock, Start.  
If the driver door is opened without first  
unlocking with the remote key, the horn will  
chirp and the lights will flash to indicate  
pre-alarm. If the vehicle is not started,  
The indicator light, on the instrument panel  
near the windshield, indicates the status of  
the system.