Get Keys and Remote Controls -> MyKey? Guide for Ford F 150 Light Truck 2023

Keys and Remote Controls

CHANGING THE REMOTE

CONTROL BATTERY -

VEHICLES WITH: FLIP KEY

WARNING: Keep batteries away

from children to prevent ingestion.

Failure to follow this instruction could

result in personal injury or death. If

ingested, immediately seek medical

attention.

E151799

3. Carefully remove the cover.

WARNING: If the battery

compartment does not securely close,

stop using the remote control and

replace it as soon as possible. In the

meantime, keep the remote control away

from children. Failure to follow this

instruction could result in personal injury

or death.

Battery Replacement Procedure

The remote control uses one coin-type

3-volt lithium battery CR2032 or

equivalent.

E151800

Press the button to release the key blade

4. Insert a screwdriver as shown to

release the battery.

before beginning the procedure.

E191533

E151801

1. Insert a screwdriver, in the position

shown and gently push the clip.

Note: Do not touch the battery contacts or

the printed circuit board with the

screwdriver.

2. Press the clip down to release the

battery cover.

5. Remove the battery.

2023 F-150 (TFD) Canada/United States of America, enUSA, Edition date: 202206, DOM

OwnersManuals2.com

Keys and Remote Controls

6. Install a new battery with the + facing

PROGRAMMINGTHEREMOTE

CONTROL - VEHICLES WITH:

PUSH BUTTON START

General Information

You must have two previously

up.

7. Replace the battery cover.

Dispose of old batteries in an

E107998

environmentally friendly way.

Seek advice from your local

authority about recycling old batteries.

programmed remote controls inside your

vehicle and the new unprogrammed

remote controls readily accessible. Contact

an authorized dealer to have the spare

remote control programmed if two

previously programmed remotes are not

available. Make sure that your vehicle is

off before beginning this procedure. Make

sure that you close all the doors before

beginning and that they remain closed

throughout the procedure. Perform all

steps within 30 seconds of starting the

sequence. Stop and wait for at least one

minute before starting again if you perform

any steps out of sequence.

Note: Do not wipe off any grease on the

battery terminals or on the back surface of

the circuit board.

Note: Replacing the battery does not erase

the programmed key from your vehicle. The

remote control should operate normally.

REPLACING A LOST KEY OR

REMOTE CONTROL

You can purchase replacement keys or

remote controls from an authorized dealer.

Authorized dealers can program remote

controls for your vehicle.

Read and understand the entire procedure

before you begin.

Note: You can program a maximum of four

remote controls to your vehicle.

Note: If your programmed remote controls

are lost or stolen and you do not have an

extra coded remote, you need to have your

vehicle towed to an authorized dealer. Store

an extra programmed remote away from

your vehicle in a safe place to help prevent

any inconvenience. Contact an authorized

dealer to purchase additional spare or

replacement remotes.

E151795

Note: Your vehicle keys came with a

security label that provides important key

cut information. Keep the label in a safe

place for future reference.

Steps for Programming Your Spare

Remote Control

Note: Your vehicle is equipped with one of

the following center consoles.

2023 F-150 (TFD) Canada/United States of America, enUSA, Edition date: 202206, DOM

OwnersManuals2.com

Keys and Remote Controls

Programming Backup Location

7. Place the unprogrammed remote

control in the backup slot and press

and release the push button ignition

switch.

Programming is now complete. With your

foot on the brake pedal, press the push

button ignition switch to verify the remote

control functions operate and your vehicle

starts with the new remote control.

If programming was not successful, wait

10 seconds and repeat Steps 1 through 7.

If you are still unsuccessful, take your

vehicle to an authorized dealer.

E312216

PROGRAMMINGTHEREMOTE

CONTROL - VEHICLES WITH:

FLIP KEY

General Information

You can program your own remote control

to your vehicle. This procedure programs

both the engine immobilizer keycode and

the remote entry portion of the remote

control to your vehicle.

E269950

Only use remote controls with an

1. Place the first programmed remote in

the backup slot inside the cup holder

or center console with your foot off the

brake pedal, press and release the push

button ignition switch.

2. Wait five seconds and then press and

release the push button ignition switch

again.

integrated mechanical key.

You must have two previously

programmed coded remote controls and

the new un–programmed remote readily

accessible. Contact an authorized dealer

to have the spare remote control

programmed if the two previously

programmed coded remote controls are

not available.

3. Remove the remote control.

4. Within 10 seconds, place a second

programmed remote control in the

backup slot. Press and release the

push button ignition switch.

5. Wait five seconds and then press and

release the push button ignition switch

again. Keep the ignition on for at least

three seconds, but no more than 10

seconds.

Read and understand the entire procedure

before you begin.

Steps for Programming Your Spare

Remote Control

1. Insert the first previously programmed

coded key into the ignition.

6. Remove the remote control.

2023 F-150 (TFD) Canada/United States of America, enUSA, Edition date: 202206, DOM

OwnersManuals2.com

Keys and Remote Controls

2. Switch the ignition from off to on. Keep

8. Switch the ignition from off to on. Keep

the ignition on for at least six seconds

until you hear the door locks cycle.

the ignition on for at least three

seconds, but no more than 10 seconds.

3. Switch the ignition off and remove the

9. Remove the newly programmed coded

first coded key from the ignition.

key from the ignition.

4. After three seconds but within 10

seconds of switching the ignition off,

insert the second previously coded key

into the ignition.

The key starts the engine if programming

is successful. You can operate the keyless

remote entry system with the new remote

control with integrated key.

5. Switch the ignition from off to on. Keep

If programming was not successful, wait

20 seconds and repeat Steps 1 through 8.

If you are still unsuccessful, take your

vehicle to an authorized dealer.

the ignition on for at least three

seconds, but no more than 10 seconds.

6. Switch the ignition off and remove the

second previously programmed coded

key from the ignition.

Note: You can program a maximum of six

coded remote controls to your vehicle.

7. After three seconds but within 10

seconds of switching the ignition off

and removing the previously

programmed coded key, insert the new

un–programmed key into the ignition.

KEYS AND REMOTE CONTROLS – TROUBLESHOOTING

KEYS AND REMOTE CONTROLS – INFORMATION MESSAGES

Message

Action

Key Battery Low Replace Replace remote control battery.

Soon

2023 F-150 (TFD) Canada/United States of America, enUSA, Edition date: 202206, DOM

OwnersManuals2.com

Keys and Remote Controls -> MyKey? for Your Ford F 150 Light Truck 2023

Popular Manuals