Get Driving Aids Guide for Ford Fiesta 4 Door 2023

Driving Aids

You can adjust the set speed in small or

SPEED LIMITER

Principle of Operation

large increments. Press the toggle button

upward or downward once to adjust the

set speed in small increments. Press and

hold the toggle button upward or

downward to adjust the set speed in large

increments.

WARNING: When you are going

downhill, your vehicle speed could

increase above the set speed. The

system does not apply the brakes.

Canceling the Set Speed

Press to cancel the set speed

limiter. The system returns to

standby mode.

WARNING:The system is designed

to aid the driver. It is not intended to

replace your attention and judgment.

You are still responsible to drive with due

care and attention.

Resuming the Set Speed

Press to resume the set speed

The system allows you to set a speed to

which your vehicle becomes limited. The

set speed sets the effective maximum

speed of your vehicle. You can temporarily

exceed the set speed if required, for

example to overtake.

limiter.

Intentionally Exceeding the Speed

Limit

Firmly press the accelerator pedal to

temporarily exceed the set speed limit. The

system resumes when the vehicle speed

drops below the set speed limit, or when

you press the RES button.

Using Speed Limiter

The controls are on the steering wheel.

Switching the System On and Off

System Warnings

If you intentionally exceed the set speed,

a warning appears in the information

display.

If you unintentionally exceed the set speed,

for example when you are going downhill,

a warning appears in the information

display and a tone sounds.

Press to set the system in

standby mode. Press again to

switch the system off.

Setting the Speed Limiter

Press the toggle button upward

or downward with the system in

standby mode to set the speed

limiter to the current vehicle

speed. The set speed is stored

and displayed in the information

display.

INTELLIGENT SPEED LIMITER

Principle of Operation

WARNING: When you are going

downhill, your vehicle speed could

increase above the set speed. The

system does not apply the brakes.

185

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Driving Aids

Note: The set speed limiter adjusts when

the system detects a different maximum

speed limit.

WARNING: You are responsible for

controlling your vehicle at all times. The

system is designed to be an aid and does

not relieve you of your responsibility to

drive with due care and attention. Failure

to follow this instruction could result in

the loss of control of your vehicle,

personal injury or death.

Note: If the system cannot detect a

maximum speed limit, the system returns

to standby mode.

You can adjust the set speed in small or

large increments. Press the toggle button

upward or downward once to adjust the

set speed in small increments. Press and

hold the toggle button upward or

downward to adjust the set speed in large

increments.

The system allows you to limit the vehicle

speed to the maximum speed limit

detected by the speed sign recognition

system. For example, if the speed sign

recognition system detects a 80 km/h

(50 mph) speed limit, the vehicle speed is

limited to 80 km/h (50 mph). You can

temporarily exceed the set speed if

required, for example to overtake.

Canceling the Set Speed

Press to cancel the set speed

limiter. The system returns to

standby mode.

Note: The speed limiter icon and the set

speed indicator are greyed out in standby

mode.

Note: The system does not limit the vehicle

speed to speed limits shown with a

supplementary traffic sign in the information

display.

Note: The system does not limit the vehicle

speed in standby mode.

Using Intelligent Speed Limiter

The controls are on the steering wheel.

Switching the System On or Off

Resuming the Set Speed

Press to resume the set speed

limiter. The system sets the

speed limiter to the detected

maximum speed limit at the time it

resumes.

Press to switch the system on.

The system activates with the

detected speed-limit or, if no

speed-limit is detected, the current vehicle

speed as the set speed. Press again to

switch the system off.

Intentionally Exceeding the Speed

Limit

Firmly press the accelerator pedal to

temporarily exceed the set speed limit. The

system resumes when the vehicle speed

drops below the set speed limit, or when

you press the RES button.

Setting the Speed Limiter

Press the toggle button upward

or downward with the system in

standby mode to set the speed

limiter to the current vehicle

speed. The set speed is stored

and displayed in the information

display.

186

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Driving Aids

System Warnings

Note: A tone sounds if you continue to

exceed the set speed.

A warning appears in the information

Note: If the speed sign recognition system

display if any of the following occur:

detects a speed limit outside the

•

The vehicle speed exceeds the current

set speed.

The system detects a maximum speed

limit that is lower than the current

vehicle speed.

operational speed range, a tone sounds and

the system returns to standby mode.

Adjusting Intelligent Speed

Limiter Tolerance Settings

•

You intentionally exceed the set speed.

You can set a permanent speed tolerance

that is in addition to the detected speed

limit through the tolerance menu in the

information display.

You unintentionally exceed the set

speed, for example when you are going

downhill. A tone also sounds.

To adjust the speed tolerance setting, use the information display controls on

the steering wheel to select the following:

Menu Item

Action

Driver assist.

Press the menu button.

Press the OK button.

Speed limiter

Intelligent

Tolerance

Press the OK button. Press the toggle button upward or

downward to choose your required speed setting. Press the

OK button.

SwitchingtoNormalSpeedLimiter

You can change between intelligent speed

limiter and normal speed limiter using the

information display. Intelligent speed

limiter allows you to limit the vehicle speed

to the maximum speed limit detected by

the speed sign recognition system. Normal

speed limiter allows you to manually limit

the vehicle speed using controls on the

steering wheel.

187

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Driving Aids

To switch between intelligent speed limiter and normal speed limiter, use the

information display controls on the steering wheel to select the following:

Menu Item

Action

Driver assist.

Press the menu button.

Press the OK button.

Speed limiter

Intelligent

Note: If you switch intelligent speed limiter

off, the system defaults to manual speed

limiter. You can manually set the speed

limiter using the controls on the steering

wheel.

WARNING: In cold and severe

weather conditions the system may not

function. Rain, snow and spray can all

limit sensor performance.

WARNING: The system will not

operate if the sensor cannot track the

road lane markings.

DRIVER ALERT

WARNING:The system is designed

to aid the driver. It is not intended to

replace your attention and judgment.

You are still responsible to drive with due

care and attention.

WARNING:Ifdamageoccursinthe

immediate area surrounding the sensor,

have your vehicle checked as soon as

possible.

WARNING: The system may not

correctly operate if your vehicle is fitted

with a suspension kit not approved by

us.

WARNING: At all times, you are

responsible for controlling your vehicle,

supervising the system and intervening,

if required. Failure to take care may result

in the loss of control of your vehicle,

serious personal injury or death.

The system is designed to alert you if it

detects that you are becoming drowsy or

if your driving deteriorates. The system

calculates your alertness level based upon

your driving behavior in relation to the lane

markings and other factors when the

vehicle speed is greater than

WARNING: The system may not

operate properly if the sensor is blocked.

Keep the windshield free from

obstruction.

approximately 65 km/h (40 mph).

WARNING: Take regular rest

breaks if you feel tired. Do not wait for

the system to warn you.

You can switch the system on or off using

the information display. See General

Information (page 91).

WARNING: Certain driving styles

may result in the system warning you

even if you are not feeling tired.

Note: The system remains on or off

depending on how it was last set.

188

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Driving Aids

Your calculated alertness level is low. You

System Warnings

The warning system has two stages:

should stop your vehicle and take a rest as

soon as it is safe to do so.

1. A temporary warning is issued to advise

you to take a rest. This message only

appears for a short time.

2. If you do not rest and the system

continues to detect that your driving

deteriorates, it issues a further warning.

This remains in the information display

until you cancel it. See Information

Messages (page 95).

Your calculated alertness level shows in

gray if:

•

The sensor cannot track the road lane

markings.

The vehicle speed falls below

approximately 65 km/h (40 mph).

Resetting the System

You can reset the system by:

Note: The system does not warn you if the

vehicle speed falls below approximately

65 km/h (40 mph).

•

Switching the ignition off and on when

your vehicle is stationary.

•

Opening and closing the driver door

when your vehicle is stationary.

System Display

Your calculated alertness level is shown

by six steps as a colored bar. The bar

travels from right to left as your calculated

alertness level decreases.

LANE KEEPING SYSTEM

You can view the status at any time using

the information display. See General

Information (page 91).

WARNING: You are responsible for

controlling your vehicle at all times. The

system is designed to be an aid and does

not relieve you of your responsibility to

drive with due care and attention. Failure

to follow this instruction could result in

the loss of control of your vehicle,

personal injury or death.

WARNING: The system may not

function if the sensor is blocked.

E249476

WARNING: The sensor may

incorrectly track lane markings as other

structures or objects. This can result in

a false or missed warning.

Your calculated alertness level is good.

WARNING: In cold and severe

weather conditions the system may not

function. Rain, snow and spray can all

limit sensor performance.

E249477

189

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Driving Aids

•

The anti-lock brake, stability control or

traction control system activates.

Narrow lane width.

WARNING: Large contrasts in

outside lighting can limit sensor

performance.

The system may not correct lane

positioning in any of the following

conditions:

•

WARNING: The system will not

operate if the sensor cannot track the

road lane markings.

High winds.

Uneven road surfaces.

Heavy or uneven loads.

Incorrect tire pressure.

WARNING:Ifdamageoccursinthe

immediate area surrounding the sensor,

have your vehicle checked as soon as

possible.

Switching Lane Keeping System

On and Off

WARNING: The system may not

correctly operate if your vehicle is fitted

with a suspension kit not approved by

us.

The system is designed to alert you by

providing temporary steering assistance

or steering wheel vibration when it detects

an unintended lane departure. The system

detects and tracks the road lane markings

using a camera mounted behind the

interior mirror. The system only operates

when the vehicle speed is greater than

approximately 65 km/h (40 mph). You

can view the system status in the

E270719

Press the button on the direction indicator

stalk.

information display.

Note: The system works when the camera

can detect at least one lane marking or the

edge of the road.

Lane Keeping System Settings

The system has different settings that you

can view or adjust using the information

display.

Note: The system remembers the last

setting when you start your vehicle. If the

system detects a MyKey, the mode is set to

alert.

The system may not correctly operate in

any of the following conditions:

•

The system does not detect at least

one lane marking or the edge of the

road.

•

You switch the direction indicator on.

You apply direct steering, accelerate

Alert Mode

Provides steering wheel vibration when the

system detects an unintended lane

departure.

fast or brake hard.

•

The vehicle speed is less than 65 km/h

(40 mph).

190

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Driving Aids

Adjusting the Steering Wheel Vibration

Alert and Aid Mode

Intensity

Provides temporary steering assistance

toward the lane center when the system

detects an unintended lane departure. If

your vehicle continues drifting out of the

lane, the steering wheel vibrates.

1. Using the information display controls

on the steering wheel, select Driver

assist..

2. Select Lane keeping system.

3. Select Intensity.

4. Select a setting and press the OK

button.

Note: This setting does not affect the aid

mode.

Note: The system remembers the last

setting when you start your vehicle.

Adjusting the Lane Keeping System

Sensitivity

1. Using the information display controls

on the steering wheel, select Driver

assist..

E165517

A

B

Alert mode.

Aid mode.

2. Select Lane keeping system.

3. Select Sensitivity.

Note: The diagram illustrates general zone

coverage. It does not provide exact zone

parameters.

4. Select a setting and press the OK

button.

Aid Mode

Provides temporary steering assistance

toward the lane center when the system

detects an unintended lane departure.

Note: When aid mode is on and the system

does not detect any steering activity for a

short period of time, for example lightly

holding the steering wheel, the system alerts

you to put your hands on the steering wheel.

Note: The aid mode becomes active again

after you have returned your vehicle to the

center of the lane.

Switching the Lane Keeping System

Mode

1. Using the information display controls

on the steering wheel, select Driver

assist..

2. Select Lane keeping system.

3. Select Mode.

4. Select a setting and press the OK

button.

191

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Driving Aids

When the system is off, the system

Lane Keeping System Display

indicator or the lane markings do not

display.

Lane Keeping System Indicators

It illuminates in the information

E251020

display when you switch the

system on and Aid Mode or Alert

and Aid Mode are selected.

E313922

It illuminates in the information

display when you switch the

system on and Alert Mode is

selected.

Black and White Information Display

Indicator

System Status

Gray.

Unavailable.

Available.

White.

White and inverted.

White and flashing.

Temporary steering assistance.

Temporary steering assistance and steering wheel vibration.

Color Information Display

Indicator

Gray.

System Status

Unavailable.

Green.

Available.

Amber.

Temporary steering assistance.

Temporary steering assistance and steering wheel vibration.

Red.

Lane Keeping System Warning

Lamp

It could illuminate when you

switch the system off. If it

illuminates when you are driving,

this indicates a malfunction. Have your

vehicle checked as soon as possible.

192

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Driving Aids

Lane Keeping System Messages

Message

Action

Lane keeping system

malfunction Service

required

The system has detected a fault that requires service. Have

your vehicle checked as soon as possible.

The system is designed to detect vehicles

that may have entered the blind spot zone.

BLIND SPOT INFORMATION

SYSTEM

The detection area is on both sides of your

vehicle, extending rearward from the

exterior mirrors to approximately 4 m

(13 ft) beyond the rear bumper. The

detection area extends to approximately

18 m (59 ft) beyond the rear bumper when

the vehicle speed is greater than 48 km/h

(30 mph) to alert you of faster

WARNING: Do not use the blind

spot information system as a

replacement for using the interior and

exterior mirrors or looking over your

shoulder before changing lanes. The

blind spot information system is not a

replacement for careful driving.

approaching vehicles.

Note: The system does not prevent contact

with other vehicles. It is not designed to

detect parked vehicles, pedestrians, animals

or other infrastructures.

WARNING: The system may not

operate properly during severe weather

conditions, for example snow, ice, heavy

rain and spray. Always drive with due

care and attention. Failure to take care

may result in a crash.

Using the Blind Spot Information

System

Vehicles with Automatic Transmission

The system turns on when all of the

following occur:

•

You start your vehicle.

You shift into drive (D).

The vehicle speed is greater than

10 km/h (6 mph).

Note: The system does not operate in park

(P) or reverse (R).

Vehicles with Manual Transmission

The system turns on when all of the

E255695

following occur:

•

You start your vehicle.

The vehicle speed is greater than

10 km/h (6 mph).

193

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Driving Aids

Note: The system does not operate in

If you switch the system off, a warning

lamp illuminates and a message displays.

When you switch the system on or off, the

alert indicators flash twice.

reverse (R).

Blind Spot Information System

Sensors

Note: The system remembers the last

setting when you start your vehicle.

Note: The system may not correctly operate

when towing a trailer. For vehicles with a

trailer tow module and tow bar approved

by us, the system turns off when you attach

a trailer. For vehicles with an aftermarket

trailer tow module or tow bar, we

recommend that you switch the system off

when you attach a trailer.

E205199

To permanently switch the system off,

The sensors are behind the rear bumper

on both sides of your vehicle.

contact an authorized dealer.

Note: Keep the sensors free from snow, ice

Blind Spot Information System

Indicator

and large accumulations of dirt.

Note: Do not cover the sensors with bumper

When the system detects a

stickers, repair compound or other objects.

E249861

vehicle, an alert indicator

Note: Blocked sensors could affect system

illuminates in the exterior mirror

performance.

on the side the approaching vehicle is

coming from. If you turn the direction

indicator on for that side of your vehicle,

the alert indicator flashes.

If the sensors are blocked, a message may

appear in the information display. The alert

indicators remain illuminated but the

system does not alert you.

If the system detects a fault, an indicator

illuminates in the instrument cluster and

a message appears in the information

display. Have your vehicle checked as soon

as possible.

Note: The system may not alert you if a

vehicle quickly passes through the detection

zone.

Switching the Blind Spot

Information System On and Off

1. Using the information display controls

on the steering wheel, select Settings.

2. Select Driver assistance.

3. Switch BLIS on or off.

194

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Driving Aids

Blind Spot Information System Information Messages

Message

Action

BLIS not available Sensor Displays if the blind spot information system sensors are

blocked See manual blocked.

BLIS deactivated Trailer Displays if you attach a trailer to your vehicle.

attached

BLIS malfunction

The system has detected a fault that requires service. Have

your vehicle checked as soon as possible.

The system is designed to alert you of

vehicles approaching from the sides when

CROSS TRAFFIC ALERT

you shift into reverse (R).

Using the Cross Traffic Alert

System

WARNING: Do not use the cross

traffic alert system as a replacement for

using the interior and exterior mirrors or

looking over your shoulder before

reversing out of a parking space. The

cross traffic alert system is not a

The system is designed to detect vehicles

that approach with a speed up to 60 km/h

(37 mph). Coverage decreases when the

sensors are partially, mostly or fully

obstructed. Slowly reversing helps increase

the coverage area and effectiveness.

replacement for careful driving.

WARNING: The system may not

operate properly during severe weather

conditions, for example snow, ice, heavy

rain and spray. Always drive with due

care and attention. Failure to take care

may result in a crash.

The system turns on when you start the

engine and you shift into reverse (R). The

system turns off when you shift out of

reverse (R).

195

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Driving Aids

E142440

The sensor on the left-hand side is only

partially obstructed and zone coverage on

the right-hand side is maximized.

E142441

196

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Driving Aids

Zone coverage also decreases when

Note: Keep the sensors free from snow, ice

parking at narrow angles. The sensor on

the left-hand side is mostly obstructed and

zone coverage on that side is severely

reduced.

and large accumulations of dirt.

Note: Do not cover the sensors with bumper

stickers, repair compound or other objects.

Note: Blocked sensors could affect system

System Lights, Messages and

Audible Alerts

performance.

If the sensors are blocked, a message may

appear in the information display when

you shift into reverse (R). See

Information Messages (page 95).

System Limitations

The system may not correctly operate

when any of the following occur:

•

The sensors are blocked.

Adjacently parked vehicles or objects

are obstructing the sensors.

•

Vehicles approach at speeds greater

than 60 km/h (37 mph).

E142442

When the system detects a vehicle, an

indicator illuminates in the exterior mirror

on the side the approaching vehicle is

coming from. A tone sounds and a

message appears in the information

display.

Note: In exceptional conditions, the system

could alert you even when there is nothing

in the detection zone, for example a vehicle

passing in the distance.

The vehicle speed is greater than

12 km/h (7 mph).

You reverse out of an angled parking

space.

System Errors

If the system detects a fault a message

displays. See General Information (page

91).

Switching the System Off and On

Blocked Sensors

You can temporarily switch the system off

using the information display. See General

Information (page 91). When you switch

system off, a message displays. See

Information Messages (page 95).

Note: The system turns on each time you

switch the ignition on and you shift into

reverse (R). If you temporarily switch the

system off, it turns on the next time you

switch the ignition on.

E205199

The sensors are behind the rear bumper

on both sides of your vehicle.

197

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Driving Aids

Note: The system may not correctly operate

Note: Traffic sign data provided by the

navigation system contains information

integrated to the data carrier release.

when towing a trailer. For vehicles with a

trailer tow module and tow bar approved

by us, the system turns off when you attach

a trailer. For vehicles with an aftermarket

trailer tow module or tow bar, we

The system detects recognizable traffic

signs, for example:

•

Speed limit signs.

No overtaking signs.

Speed limit cancellation signs.

No overtaking cancellation signs.

recommend that you switch the system off

when you attach a trailer.

To permanently switch the system off,

contact an authorized dealer.

Note: The system may not detect all traffic

TRAFFIC SIGN RECOGNITION

Principle of Operation

signs and may incorrectly read signs.

Note: In cold and severe weather conditions

the system may not function. Rain, snow,

spray and large contrasts in lighting can all

prevent the sensor from correctly

functioning.

Note: If your vehicle has a suspension kit

not approved by us, the system may not

correctly function.

WARNING: You are responsible for

controlling your vehicle at all times. The

system is designed to be an aid and does

not relieve you of your responsibility to

drive with due care and attention. Failure

to follow this instruction could result in

the loss of control of your vehicle,

personal injury or death.

Note: Always fit Ford original parts when

replacing headlamp bulbs. Other bulbs may

reduce system performance.

The system turns on when you switch the

ignition on and you cannot switch the

system off.

WARNING: The system may not

operate properly if the sensor is blocked.

Keep the windshield free from

obstruction.

Using Traffic Sign Recognition

Setting the System Speed Warning

You can set the system speed warning to

alert you when the vehicle speed exceeds

the speed limit recognized by the system

by a certain speed tolerance.

The system is designed to detect traffic

signs to inform you of the current speed

limit and overtaking regulations. Detected

traffic signs appear in the information

display. The sensor is behind the interior

mirror.

Note: Do not carry out windshield repairs

in the immediate area surrounding the

sensor.

198

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Driving Aids

To switch the system speed warning on or off, or to adjust the speed warning

settings, use the information display controls on the steering wheel to select the

following:

Menu Item

Driver assist.

Traffic sign recognition

Action

Press the menu button.

Press the OK button.

Activate speed warning Press the OK button.

Speed warning

Tolerance

Press the menu button.

Press the OK button. Press the toggle button upward or

downward to choose your required speed setting. Press the

OK button.

Overspeed chime

Press the OK button.

The system displays recognizable traffic

Traffic Sign Recognition System

Display

signs in four stages as follows:

1. All new traffic signs appear brighter

than the others in the display.

2. After a predetermined time they

display normally.

3. After a predetermined distance they

are greyed out.

4. After another predetermined distance

they are deleted.

If the system detects a supplementary

traffic sign, it displays below the respective

traffic sign. For example, when passing a

reduced speed limit in wet road conditions

sign.

Note: If your vehicle has a navigation

system, stored traffic sign data may

influence the indicated speed limit value.

E132994

The system can display two traffic signs

in parallel.

You can view the status at any time using

the information display.

199

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Driving Aids

Traffic Sign Recognition System Messages

Message

Action

Traffic sign recognition

Reduced performance

See manual

The traffic sign data provided by the navigation system is

unavailable due to weak or no signal. Wait for a short period

of time for the signal to improve. If the message continues

to appear, have your vehicle checked as soon as possible.

Note: In cold and severe weather conditions

the system may not function. Rain, snow,

SPEED SIGN RECOGNITION

Principle of Operation

spray and large contrasts in lighting can all

prevent the sensor from correctly

functioning.

Note: If your vehicle has a suspension kit

not approved by us, the system may not

correctly function.

Note: Always fit Ford original parts when

replacing headlamp bulbs. Other bulbs may

reduce system performance.

The system turns on when you switch the

ignition on and you cannot switch the

system off.

WARNING: You are responsible for

controlling your vehicle at all times. The

system is designed to be an aid and does

not relieve you of your responsibility to

drive with due care and attention. Failure

to follow this instruction could result in

the loss of control of your vehicle,

personal injury or death.

WARNING: The system may not

operate properly if the sensor is blocked.

Keep the windshield free from

obstruction.

Using Speed Sign Recognition

Setting the System Speed Warning

You can set the system speed warning to

alert you when the vehicle speed exceeds

the speed limit recognized by the system

by a certain speed tolerance.

The system is designed to detect speed

limit signs to inform you of the current

speed limit. Detected speed signs appear

in the information display. The sensor is

behind the interior mirror.

Note: The system remembers the last

setting when you start your vehicle.

Note: Do not carry out windshield repairs

in the immediate area surrounding the

sensor.

Note: Speed sign data provided by the

navigation system contains information

integrated to the data carrier release.

1. Using the information display controls

on the steering wheel, select Driver

assist..

2. Select Traffic sign recognition.

3. Select Activate Traff. Sign Recog..

4. Select Activate speed warning.

5. Select Speed warning.

Note: The system may not detect all speed

signs and may incorrectly read signs.

6. Select Tolerance.

7. Select a setting and press the OK

button.

200

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Driving Aids

When the system detects a speed limit

Speed Sign Recognition System

Display

sign, the speed limit appears in the

information display.

Note: If your vehicle has a navigation

system, stored speed sign data could

influence the indicated speed limit value.

E318471

Speed Sign Recognition System Messages

Message

Action

Traffic sign recognition

Reduced performance

See manual

The traffic sign data provided by the navigation system is

unavailable due to weak or no signal. Wait for a short period

of time for the signal to improve. If the message continues

to appear, have your vehicle checked as soon as possible.

Eco Mode System Display

You can view the instantaneous efficiency

level or the trip summary in the information

display.

ECO

Principle of Operation

The system is designed to monitor certain

driving characteristics to help you drive

more efficiently. See Economical Driving

(page 219).

Note: The efficiency levels do not result in

a defined fuel consumption figure. See Fuel

Consumption (page 146).

Note: The system only indicates the

efficiency level for the current trip. The

system resets each time you switch the

ignition on.

Instantaneous Efficiency Level

The display ring increases as the

instantaneous efficiency level increases

and illuminates when it reaches maximum

efficiency. The level continuously updates

to indicate the efficiency level for the

current trip.

To view the instantaneous efficiency level, use the information display controls

on the steering wheel to select the following:

Menu Item

MyView

Eco coach

Action

Press the menu button.

Press the OK button.

201

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Driving Aids

Trip Summary

deceleration, speed and gear shifting

during the total distance traveled by your

vehicle for the current trip.

The calculated trip summary is shown as

four colored bars. The bars travel from left

to right as the calculated efficiency levels

increase. The bars indicate the average

efficiency level for acceleration,

Note: Vehicles with an automatic

transmission do not have a bar for gear

shifting.

To view the trip summary, use the information display controls on the steering

wheel to select the following:

Menu Item

MyView

Eco coach

Action

Press the menu button.

Press the OK button. Press it again to view the trip summary.

WARNING: The system may not

PRE-COLLISION ASSIST

operate properly if your vehicle has a

non-Ford windshield. Do not carry out

windshield repairs in the area around the

sensor.

WARNING: You are responsible for

controlling your vehicle at all times. The

system is designed to be an aid and does

not relieve you of your responsibility to

drive with due care and attention. Failure

to follow this instruction could result in

the loss of control of your vehicle,

personal injury or death.

WARNING: In situations where the

vehicle camera has limited detection

capability, this may reduce system

performance. These situations include

but are not limited to direct or low

sunlight, vehicles at night without tail

lights, unconventional vehicle types,

pedestrians with complex backgrounds,

running pedestrians, partly obscured

pedestrians, or pedestrians that the

system cannot distinguish from a group.

Failure to take care may result in the loss

of control of your vehicle, serious

personal injury or death.

WARNING: The system does not

operate during hard acceleration or

steering. Failure to take care may lead

to a crash or personal injury.

WARNING: The system may fail or

operate with reduced function during

cold and severe weather conditions.

Snow, ice, rain, spray and fog can

adversely affect the system. Keep the

front camera and radar free of snow and

ice. Failure to take care may result in the

loss of control of your vehicle, serious

personal injury or death.

WARNING:The Pre-Collision Assist

system with brake support cannot help

prevent all collisions. Do not rely on this

system to replace your judgment and the

need to maintain correct distance and

speed.

202

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Driving Aids

The pre-collision assist system is active

when your vehicle reaches a speed greater

than approximately 5 km/h (3 mph).

Pedestrian detection is active at speeds

up to 80 km/h (50 mph).

E156130

If your vehicle is rapidly approaching

another stationary vehicle, a vehicle or

cyclist traveling in the same direction as

yours, or a pedestrian within your driving

path, the system is designed to provide

three levels of functionality.

Note: The system is not designed to detect

animals.

Note: The system is not designed to detect

vehicles or cyclists that are traveling in a

different direction.

Level of Functionality

Description

Alert

When activated, a warning lamp flashes and an audible

warning sounds.

Brake support

The system is designed to help reduce the impact speed by

preparing the brakes for rapid braking. The system does not

automatically apply the brakes. If you press the brake pedal,

the system could apply additional braking up to maximum

braking force, even if you lightly press the brake pedal.

Active braking - vehicles The system is designed to apply the brakes if it detects a

without adaptive cruise crash is imminent. This may help reduce impact or avoid the

control

crash.

The system is active at speeds up to 130 km/h (80 mph).

Active braking - vehicles The system is designed to apply the brakes if it detects a

with adaptive cruise

control

crash is imminent. This may help reduce impact or avoid the

crash.

To switch active braking on or off, use the information display controls on the

steering wheel to select the following:

Menu Item

Action

Driver assist.

Press the menu button.

Press the OK button.

Pre-collision Assist

Active braking

Note: The warning lamp does not

illuminate if cruise control or adaptive cruise

control is active.

Distance Alert (If Equipped)

A warning lamp illuminates if the distance

to the vehicle ahead is small.

203

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Driving Aids

Distance Alert Sensitivity Settings

To adjust the distance alert sensitivity settings, use the information display

controls on the steering wheel to select the following:

Menu Item

Driver assist.

Action

Press the menu button.

Pre-collision Assist

Alert sensitivity

Press the OK button.

Press the OK button. Press the toggle button upward or

downward to choose your required setting. Press the OK

button.

Note: The graphic does not display if you

Distance Indication^{(If Equipped)}

A graphical indication displays the time

gap to vehicles ahead of you traveling in

the same direction.

switch on cruise control or adaptive cruise

control.

Vehicle Speed System Sensit- Distance Indic-

Distance Gap

Time Gap

ivity

ator Color

Gray.

100 km/h

(62 mph)

Normal.

Greater than

Greater than 0.9

seconds.

25 m (82.0 ft) .

Yellow.

Red.

17–25 m

0.6-0.9

(55.8–82.0 ft).

seconds.

Less than 17 m

(55.8 ft).

Less than 0.6

seconds.

Switching Distance Indication On or Off

To switch distance indication on or off, use the information display controls on

the steering wheel to select the following:

Menu Item

Driver assist.

Action

Press the menu button.

Press the OK button.

Pre-collision Assist

Distance indication

204

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Driving Aids

The camera is mounted behind the interior

Pre-Collision Assist System

Sensors

mirror.

Vehicles without Adaptive Cruise

Control

E243054

E244279

The camera is mounted behind the interior

mirror.

The radar sensor is behind the front grille

below the license plate.

Note: Keep the sensors free from snow, ice

and large accumulations of dirt.

Note: Do not clean the sensors with sharp

objects.

Note: If your vehicle sustains damage

leaving the sensors misaligned, this may

cause inaccurate measurements or false

alerts.

Blocked sensors could affect system

accuracy. A message may appear in the

information display.

Note: If your vehicle sustains damage

leaving the sensors misaligned, this may

cause inaccurate measurements or false

alerts.

Blocked sensors could affect system

accuracy. A message may appear in the

information display.

Vehicles with Adaptive Cruise Control

Pre-CollisionAssistWarningLamp

It illuminates if your vehicle

rapidly approaches another

vehicle, to warn you of the risk of

a crash with the vehicle in front of you.

It could illuminate red if the distance to the

vehicle ahead is small.

It illuminates when the system is not

available.

E243054

205

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Driving Aids

Pre-Collision Assist Information Messages

Message

Action

Pre-collision assist not

available

The system has malfunctioned. Have your vehicle checked

as soon as possible.

Pre-collision assist not

The sensors are dirty. Clean the sensors. If the message

available Sensor blocked continues to appear, have your vehicle checked as soon as

possible.

The following table lists possible causes and actions for when a blocked sensor

message may display.

Cause

Action

The surface of the radar in the radiator grille Clean the radiator grille in front of the radar

is dirty or obstructed.

or remove any obstruction.

The surface of the radar is clean but the

message remains in the display.

Wait for a short period of time. It may take

several minutes for the system to detect

that there is no obstruction.

Heavy rain, spray, snow, or fog is interfering The system is temporarily disabled. The

with the radar signals.

system should reactivate after a short

period of time when the weather conditions

improve.

The radar is misaligned.

Have your vehicle checked as soon as

possible.

The windshield in front of the camera is

dirty or obstructed.

Clean the outside of the windshield in front

of the camera.

The windshield in front of the camera is

clean but the message remains in the

display.

Wait for a short period of time. It may take

several minutes for the camera to detect

that there is no obstruction.

Excessive heat around the camera.

Wait for a short period of time. The

message should clear when the temper-

ature around the camera decreases.

206

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Driving Aids

Trail

DRIVE CONTROL

Vehicle settings suited for driving

on unpaved roads.

Selectable Drive Modes

Your vehicle has various drive modes that

you can select for different driving

Track

conditions. Depending on the drive mode

that you select, the system adjusts various

vehicle settings, for example steering, gear

shifting, handling and powertrain response.

Vehicle settings suited for track

driving.

E269330

Note: Auto-start-stop switches off when

you select this mode.

Selecting a Drive Mode

The button is on the center console.

Note: Pre-Collision Assist is disabled when

you select this mode.

Repeatedly press the button to

E267358

Note: Lane Keeping System is disabled

scroll through the available drive

modes.

when you select this mode.

Note: Track mode is not intended for use

E269240

on public roads.

Note: Some drive modes cannot be

Note: Stability Control is adapted for track

selected when using a MyKey.

use when you select this mode.

Normal

Vehicle settings suited for

balanced driving.

N^Eo²t²⁵e³:¹⁰This is the default mode each time

you switch the ignition on.

Eco

Vehicle settings suited for

E267164

economical driving.

Slippery

Vehicle settings suited for driving

on slippery roads.

E269320

Sport

Vehicle settings suited for

sportier driving.

E246593

Note: Auto-start-stop switches off when

you select this mode.

207

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Driving Aids for Your Ford Fiesta 4 Door 2023

Popular Manuals