Get Lighting Guide for Ford Fiesta 4 Door 2023

Lighting

GENERAL INFORMATION

LIGHTING CONTROL

Condensation in the Exterior Front

Lighting Control Positions

Lamps and Rear Lamps

Exterior front lamps and rear lamps have

vents to accommodate normal changes

in air pressure.

B

C

A

D

Condensation can be a natural by-product

of this design. When moist air enters the

lamp assembly through the vents, there is

a possibility that condensation can occur

when the temperature is cold. When

normal condensation occurs, a fine mist

can form on the interior of the lens. The

fine mist eventually clears and exits

through the vents during normal operation.

Clearing time may take as long as 48 hours

under dry weather conditions.

Examples of acceptable condensation are:

•

The presence of a fine mist (no streaks,

E245649

drip marks or large droplets).

•

A fine mist covers less than 50% of the

lens.

A

B

Lamps off.

Parking lamps, instrument panel

Examples of unacceptable condensation

lamps and license plate lamps.

are:

•

C

D

Headlamps.

A water puddle inside the lamp.

Autolamps. See Autolamps

Streaks, drip marks or large droplets

(page 72).

present on the interior of the lens.

If you see any unacceptable condensation,

have your vehicle checked by an authorized

dealer.

Switchin g A l l o f t h e P arkin g L amps

On

1. Switch the ignition off.

2. Set the lighting control to the parking

lamps position.

Note: Parking lamps could turn off to

prevent the vehicle battery from running out

of charge.

Switching the Left-Hand Side or

the Right-Hand Side Parking

Lamps On(If Equipped)

1. Switch the ignition off.

70

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Lighting

Flashing High Beam Headlamps

E242676

E248604

2. Push the lever up or down to switch the

parking lamps on.

Note: Parking lamps could turn off to

prevent the vehicle battery from running out

of charge.

Pull the lever toward you and release it to

flash the high beam headlamps.

High Beam Headlamp Indicator

It illuminates when you switch

Switching High Beam Headlamps

On and Off

the high beam headlamps on.

Lamps On Indicator

It illuminates when you switch

the low beam headlamps or the

side and rear lamps on.

Low Beam Headlamp Warning

Lamp (If Equipped)

If it illuminates when the low

E250683

beam headlamps are on, this

E248603

indicates that a low beam

headlamp bulb has failed.

Push the lever away from you to switch

the high beam headlamps on.

Push the lever forward again or pull the

lever toward you to switch the high beam

headlamps off.

Note: If you switch the autolamps on, you

cannot switch the high beam headlamps

on until the system turns the headlamps on.

Exterior Lamps On Audible

Warning

Sounds when you open the driver door and

the exterior lamps are on.

71

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Lighting

Headlamps Information Messages

Message

Description

Check adaptive head-

lamps See manual

Displays if an electrical malfunction occurs with the headlamp

system. Have your vehicle checked as soon as possible.

Note: The headlamps turn off

approximately 60 seconds after you switch

the wipers off.

AUTOLAMPS

The headlamps remain on for a period of

time after you switch the ignition off. Use

WARNING: The system does not

the information display controls to adjust

the period of time that the headlamps

remain on.

relieve you of your responsibility to drive

with due care and attention. You may

need to override the system if it does not

turn the headlamps on in low visibility

conditions, for example daytime fog.

Adjusting the Period of Time That

the Headlamps Remain On

1. Using the information display controls

Autolamps turn the headlamps on in low

light situations or when the wipers operate.

on the steering wheel, select Settings.

2. Select Vehicle settings.

3. Select Lighting.

4. Select Headlamp delay.

5. Select a setting.

6. Press the OK button.

INSTRUMENT LIGHTING

DIMMER

The instrument lighting dimmer buttons

are on the lighting control.

Repeatedly press one of the

buttons to adjust the brightness.

E253316

E291299

Note: When you switch the autolamps on,

the headlamps turn on within 10 seconds of

switching the wipers on.

E291298

Note: If you switch the autolamps and the

autowipers on, the headlamps turn on when

the windshield wipers continuously operate.

72

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Lighting

HEADLAMP EXIT DELAY

WARNING:Inspect and replace the

windshield wiper blades regularly to

make sure the camera sensor has a clear

view. The windshield wiper blades must

be the correct length.

After you switch the ignition off, you can

switch the headlamps on by pulling the

direction indicator lever toward you. You

will hear a short tone. The headlamps will

switch off automatically after three

minutes with any door open or 30 seconds

after the last door has been closed. You

can cancel this feature by pulling the

direction indicator toward you again or

switching the ignition on.

About Automatic High Beam

Control

The system is designed to turn the high

beams on if all of the following occur:

•

You switched the system on in the

information display.

AUTOMATIC HIGH BEAM

CONTROL

You set the lighting control to the

autolamps position.

The ambient light level is low enough

that high beams are required.

WARNING: The system does not

relieve you of your responsibility to drive

with due care and attention. You may

need to override the system if it does not

turn the high beams on or off.

There is no traffic in front of your

vehicle.

Your vehicle speed is greater than

approximately 40 km/h (25 mph).

The system is designed to turn the high

WARNING: You may need to

override the system when approaching

other road users.

beams off if any of the following occur:

•

You switch the system off in the

information display.

WARNING: You may need to

override the system during inclement

weather.

You set the lighting control to any

position except autolamps.

•

You switch the rear fog lamps on.

WARNING: Do not use the system

in poor visibility, for example fog, heavy

rain, spray or snow.

The ambient light level is high enough

that high beams are not required.

•

The system detects an approaching

vehicle's headlamps or rear lamps.

WARNING: The system may not

switch the high beams off if the lights of

oncoming vehicles are hidden by

The system detects severe rain, snow

or fog.

obstacles, for example guard rails.

•

The system detects street lighting.

The camera has reduced visibility.

Your vehicle speed falls below

approximately 30 km/h (19 mph).

73

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Lighting

Switching Automatic High Beam Control On or Off

To switch the system on or off, use the information display controls on the steering

wheel to select the following:

Menu Item

Settings

Action

Press the menu button.

Press the OK button.

Vehicle settings

Lighting

Auto highbeam

Automatic High Beam Indicator

Overriding Automatic High Beam

Control

It illuminates to confirm when

the system is ready to assist.

Push the lever away from you to switch

between high beam and low beam.

Automatic High Beam Control Information Messages

Message

Description

Front camera Low visib- The camera has reduced visibility. Clean the windshield. If

ility Clean screen

the message continues to appear, have your vehicle checked

as soon as possible.

Front camera temporarily The camera has malfunctioned. Wait a short period of time

not available

for the camera to cool down. If the message continues to

appear, have your vehicle checked as soon as possible.

You can switch the front fog lamps on if

any of the following occur:

FRONT FOG LAMPS

•

You set the lighting control to the

parking lamps position.

SwitchingtheFrontFogLampsOn

You set the lighting control to the

headlamps position.

You set the lighting control to the

autolamps position and the headlamps

are on.

or Off

Only switch the front fog lamps on during

reduced visibility.

The front fog lamp button is on the lighting

control.

Press the button to switch the

front fog lamps on or off.

74

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Lighting

Note: The brightness of the daytime running

HEADLAMP LEVELING

lamps may decrease when the front fog

lamps are switched on.

To adjust the level of the headlamp

beams, do the following:

Front Fog Lamp Indicator

It illuminates when you switch

the front fog lamps on.

2

REAR FOG LAMPS

Switching the Rear Fog Lamps On

2

or Off

1

WARNING: Do not use the rear fog

lamps when it is raining or snowing and

visibility is more than 50 m (164.0 ft).

E132711

You can switch the rear fog lamps on if any

of the following occur:

1. Press to release the control.

•

You switched the front fog lamps on.

2. Rotate the control in accordance with

your vehicle load to prevent you from

distracting other road users when the

headlamps are on.

You set the lighting control to the

headlamps position.

•

You set the lighting control to the

autolamps position and the headlamps

are on.

Note: Set the control to zero when your

vehicle is unloaded.

Note: Set the headlamp beams to give

between 35–100 m (115–328 ft) of road

surface illumination when your vehicle is

partially or fully loaded.

The rear fog lamp button is on the lighting

control.

Press the button to switch the

rear fog lamps on or off.

E67040

3. Press to close the control.

Rear Fog Lamp Indicator

It illuminates when you switch

the rear fog lamps on.

E67040

75

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Lighting

CORNERING LAMPS

E72898

A

B

Headlamp beam.

Cornering lamp beam.

The cornering lamps illuminate the inside

of a corner when you are turning the

steering wheel.

DIRECTION INDICATORS

E242676

76

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Lighting

Push the lever up or down to use

Switching the Rear Interior Lamps

On and Off

the direction indicators.

Note: Tap the lever up or down to make the

direction indicators flash three times.

INTERIOR LAMPS - VEHICLES

WITH:FRONTINTERIORLAMP

WITH MAP READING LAMPS

Switching All of the Interior Lamps

On and Off

E250958

Interior Lamp Function

E310027

E264886

When you set the switch to the middle

position, the interior lamps turn on if:

E310028

•

You open a door.

You press the unlock button on the

Switching the Front Interior Lamps

On and Off

remote control.

•

You switch the ignition off.

Note: If you switch the ignition off, the

interior lamps could turn off after a short

time to prevent the vehicle battery from

running out of charge.

E249791

Note: Press the edge of the lamps lens to

switch the front interior lamp off before

switching the ignition off to prevent the

vehicle battery from running out of charge.

77

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Lighting

Interior Lamp Function

INTERIOR LAMPS - VEHICLES

WITH:FRONTINTERIORLAMP

Switching All of the Interior Lamps

On and Off

E264562

When you set the switch to the middle

position, the interior lamps turn on if:

•

You open a door.

E309989

You press the unlock button on the

remote control.

•

You switch the ignition off.

Note: If you switch the ignition off, the

interior lamps could turn off after a short

time to prevent the vehicle battery from

running out of charge.

E309990

Switching the Rear Interior Lamps

On and Off

E309994

E309995

78

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Lighting for Your Ford Fiesta 4 Door 2023

Popular Manuals