Get Maintenance Guide for Ford Fiesta 4 Door 2023

Maintenance

Check Monthly

GENERAL INFORMATION

•

Engine oil level. See Engine Oil Check

(page 246).

Engine coolant level. See Engine

WARNING: Do not work on a hot

engine.

Coolant Check (page 248).

Brake fluid level. See Brake Fluid

Check (page 249).

WARNING: Switch the ignition off

and apply the parking brake.

•

Pipes, hoses and reservoirs f or leaks.

Air conditioning operation.

Parking brake operation.

Horn operation.

WARNING: Do not touch the

electronic ignition system parts after you

have switched the ignition on or when

the engine is running. The system

operates at high voltage. Failure to

adhere to this warning could result in

serious personal injury or death.

Tightness of lug nuts. See Lug Nuts

(page 296).

OPENING AND CLOSING THE

HOOD

WARNING: Keep your hands and

clothing clear of the engine cooling fan.

Opening the Hood

Under certain conditions, the engine

cooling fan may continue to run for several

minutes after you switch your vehicle off.

See Engine Cooling Fan (page 248).

Make sure that you fit filler caps securely

after carrying out maintenance checks.

We recommend that you carry out the

following checks.

Check Daily

•

Exterior lamps.

Interior lamps.

Warning lamps and indicators.

E236610

Check When Refueling

1. Pull the hood release lever.

•

Washer fluid level. See Washer Fluid

Check (page 252).

Tire pressures. See Tire Pressures

(page 287).

Tire condition. See Wheels and Tires

(page 268).

236

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Maintenance

2

3

E87786

5. Support the hood with the strut.

Closing the Hood

1. Remove the strut from the catch and

secure it correctly in the clip.

E236611

2. Lower the hood and allow it to drop

under its own weight for the last

20–30 cm (8–12 in).

2. Slightly lift the hood.

3. Release the hood latch by pushing the

secondary release lever to your

left-hand side.

Note: Make sure that the hood is correctly

closed.

4. Open the hood.

237

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Maintenance

UNDER HOOD OVERVIEW - 1.0L ECOBOOST™, LHD

A

B

C

D

E

F

H

G

E236612

A

B

C

D

E

F

G

H

Engine coolant reservoir. See Engine Coolant Check (page 248).

Engine oil dipstick. See Engine Oil Dipstick (page 246).

Engine oil filler cap. See Engine Oil Check (page 246).

Brake fluid reservoir. See Brake Fluid Check (page 249).

Battery. See Changing the 12V Battery (page 250).

Engine compartment fuse box. See Fuses (page 227).

Air filter.

Windshield washer fluid reservoir. See Washer Fluid Check (page 252).

238

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Maintenance

UNDER HOOD OVERVIEW - 1.0L ECOBOOST™, RHD

A

B

C

D

E

F

H

G

E236613

A

B

C

D

E

F

G

H

Engine coolant reservoir. See Engine Coolant Check (page 248).

Brake fluid reservoir. See Brake Fluid Check (page 249).

Engine oil dipstick. See Engine Oil Dipstick (page 246).

Engine oil filler cap. See Engine Oil Check (page 246).

Battery. See Changing the 12V Battery (page 250).

Engine compartment fuse box. See Fuses (page 227).

Air filter.

Windshield washer fluid reservoir. See Washer Fluid Check (page 252).

239

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Maintenance

UNDER HOOD OVERVIEW - 1.1L DURATEC, LHD

A

B

C

D

E

F

H

G

E236614

A

B

C

D

E

F

G

H

Engine coolant reservoir. See Engine Coolant Check (page 248).

Engine oil dipstick. See Engine Oil Dipstick (page 246).

Engine oil filler cap. See Engine Oil Check (page 246).

Brake fluid reservoir. See Brake Fluid Check (page 249).

Battery. See Changing the 12V Battery (page 250).

Engine compartment fuse box. See Fuses (page 227).

Air filter.

Windshield washer fluid reservoir. See Washer Fluid Check (page 252).

240

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Maintenance

UNDER HOOD OVERVIEW - 1.1L DURATEC, RHD

A

B

C

D

E

F

H

G

E236615

A

B

C

D

E

F

G

H

Engine coolant reservoir. See Engine Coolant Check (page 248).

Brake fluid reservoir. See Brake Fluid Check (page 249).

Engine oil dipstick. See Engine Oil Dipstick (page 246).

Engine oil filler cap. See Engine Oil Check (page 246).

Battery. See Changing the 12V Battery (page 250).

Engine compartment fuse box. See Fuses (page 227).

Air filter.

Windshield washer fluid reservoir. See Washer Fluid Check (page 252).

241

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Maintenance

UNDER HOOD OVERVIEW - 1.5L DURATORQ-TDCI DIESEL, LHD

A

B

C

D

E

H

G

F

E236618

A

B

C

D

E

Engine coolant reservoir. See Engine Coolant Check (page 248).

Engine oil filler cap. See Engine Oil Check (page 246).

Brake fluid reservoir. See Brake Fluid Check (page 249).

Battery. See Changing the 12V Battery (page 250).

Engine compartment fuse box. See Fuses (page 227).

Air filter.

F

G

H

Engine oil dipstick. See Engine Oil Dipstick (page 246).

Windshield washer fluid reservoir. See Washer Fluid Check (page 252).

242

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Maintenance

UNDER HOOD OVERVIEW - 1.5L DURATORQ-TDCI DIESEL, RHD

A

B

C

D

E

H

G

F

E236619

A

B

C

D

E

Engine coolant reservoir. See Engine Coolant Check (page 248).

Brake fluid reservoir. See Brake Fluid Check (page 249).

Engine oil filler cap. See Engine Oil Check (page 246).

Battery. See Changing the 12V Battery (page 250).

Engine compartment fuse box. See Fuses (page 227).

Air filter.

F

G

H

Engine oil dipstick. See Engine Oil Dipstick (page 246).

Windshield washer fluid reservoir. See Washer Fluid Check (page 252).

243

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Maintenance

UNDER HOOD OVERVIEW - 1.5L ECOBOOST™, LHD

A

B

C

D

E

F

H

G

E236616

A

B

C

D

E

F

G

H

Engine coolant reservoir. See Engine Coolant Check (page 248).

Engine oil dipstick. See Engine Oil Dipstick (page 246).

Engine oil filler cap. See Engine Oil Check (page 246).

Brake fluid reservoir. See Brake Fluid Check (page 249).

Battery. See Changing the 12V Battery (page 250).

Engine compartment fuse box. See Fuses (page 227).

Air filter.

Windshield and rear window washer reservoir. See Washer Fluid Check (page

252).

244

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Maintenance

UNDER HOOD OVERVIEW - 1.5L ECOBOOST™, RHD

A

B

C

D

E

F

H

G

E236617

A

B

C

D

E

F

G

H

Engine coolant reservoir. See Engine Coolant Check (page 248).

Brake fluid reservoir. See Brake Fluid Check (page 249).

Engine oil dipstick. See Engine Oil Dipstick (page 246).

Engine oil filler cap. See Engine Oil Check (page 246).

Battery. See Changing the 12V Battery (page 250).

Engine compartment fuse box. See Fuses (page 227).

Air filter.

Windshield and rear window washer reservoir. See Washer Fluid Check (page

252).

245

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Maintenance

ENGINE OIL DIPSTICK - 1.0L

ECOBOOST™/1.1L DURATEC

ENGINE OIL DIPSTICK - 1.5L

ECOBOOST™

A

B

A

B

E264320

E141337

A

B

Minimum.

Maximum.

A

B

Minimum.

Maximum.

ENGINE OIL DIPSTICK - 1.5L

DURATORQ-TDCI DIESEL

ENGINE OIL CHECK

1. Make sure that your vehicle is on level

ground.

B

A

2. Check the oil level before starting the

engine, or switch the engine off and

wait 10 minutes for the oil to drain into

the oil pan.

3. Remove the dipstick and wipe it with

a clean, lint-free cloth. Reinstall the

dipstick and remove it again to check

the oil level.

E140423

If the oil level is at the minimum mark,

A

B

Minimum.

Maximum.

immediately add oil.

Note: Make sure that the oil level is

between the minimum and the maximum

marks.

Note: The oil consumption of new engines

reaches its normal level after approximately

5,000 km (3,000 mi).

246

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Maintenance

3. Add engine oil that meets our

Adding Engine Oil

specifications. See Capacities and

Specifications (page 297).

4. Reinstall the engine oil filler cap. Turn

it clockwise until you feel a strong

resistance.

Note: Do not add oil further than the

maximum mark. Oil levels above the

maximum mark may cause engine damage.

WARNING: Do not add engine oil

when the engine is hot. Failure to follow

this instruction could result in personal

injury.

WARNING: Do not remove the filler

cap when the engine is running.

Note: Immediately soak up any oil spillage

with an absorbent cloth.

Do not use supplemental engine oil

additives because they are unnecessary

and could lead to engine damage that may

not be covered by the vehicle Warranty.

OIL CHANGE INDICATOR

RESET

1. Clean the area surrounding the engine

oil filler cap before you remove it.

Only reset the system after changing the

2. Remove the engine oil filler cap.

engine oil and oil filter.

To reset the oil change indicator, use the information display controls on the

steering wheel to select the following:

Menu item

Action

Settings

Press the menu button.

Press the OK button.

Information

Oil life

Reset oil life

Press and hold the OK button until the system reset

confirmation appears.

247

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Maintenance

ENGINE COOLING FAN -

GASOLINE

WARNING: Keep your hands and

clothing clear of the engine cooling fan.

Under certain conditions, the engine

cooling fan may continue to run for several

minutes after you switch your vehicle off.

ENGINE COOLING FAN -

DIESEL

WARNING: Keep your hands and

E170684

clothing clear of the engine cooling fan.

Make sure that the coolant level is

Under certain conditions, the engine

cooling fan may continue to run for several

minutes after you switch your vehicle off.

This could happen in low ambient

between the MIN and MAX marks on the

coolant reservoir at ambient temperature.

If the coolant level is at or below the

minimum mark, immediately add coolant.

temperatures and independent of the

engine coolant temperature, for example

short journeys or low coolant temperature.

See Diesel Particulate Filter (page 150).

The coolant concentration should be

maintained within 48% to 50%, which

equates to a freeze point between -34°C

(-29°F) and -37°C (-35°F).

Note: Coolant expands when it is hot. The

ENGINE COOLANT CHECK

level may extend beyond the MAX mark.

Note: Do not use stop leak pellets, cooling

system sealants, or non-specified additives

as they can cause damage to the engine

cooling or heating systems.

WARNING: Do not dispose of

coolant in the household refuse or the

public sewage system. Use an authorized

waste disposal facility.

WARNING: Do not put coolant in

the windshield washer reservoir. If

sprayed on the windshield, coolant could

make it difficult to see through the

windshield.

248

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Maintenance

In case of emergency, you can add water

Adding Coolant

without engine coolant in order to reach a

vehicle service location.

WARNING: Do not remove the

Note: Prolonged use of an incorrect dilution

of coolant can cause damage, for example

corrosion, overheating or freezing.

coolant reservoir cap when the engine is

on or the cooling system is hot. Wait 10

minutes for the cooling system to cool

down. Cover the coolant reservoir cap

with a thick cloth to prevent the

BRAKE FLUID CHECK

possibility of scalding and slowly remove

the cap. Failure to follow this instruction

could result in personal injury.

WARNING: Do not use any fluid

other than the recommended brake fluid

as this will reduce brake efficiency. Use

of incorrect fluid could result in the loss

of vehicle control, serious personal injury

or death.

WARNING: Do not allow the fluid

to touch your skin or eyes. If this

happens, rinse the affected areas

immediately with plenty of water and

contact your physician.

WARNING: Only use brake fluid

from a sealed container. Contamination

with dirt, water, petroleum products or

other materials may result in brake

system damage or failure. Failure to

adhere to this warning could result in the

loss of vehicle control, serious personal

injury or death.

WARNING: Undiluted coolant is

flammable and may ignite if spilled on a

hot exhaust.

We do not recommend the use of recycled

engine coolant since a Ford-approved

recycling process is not yet available.

Do not mix different colors or types of

WARNING: Do not allow the fluid

to touch your skin or eyes. If this

happens, rinse the affected areas

immediately with plenty of water and

contact your physician.

coolant in your vehicle.

Note: Add a 50/50 mixture of antifreeze

and water or prediluted engine coolant that

meets the correct specification.

Note: Use fluids which meet the

WARNING: A fluid level between

the MAX and MIN lines is within the

normal operating range and there is no

need to add fluid. A fluid level not in the

normal operating range could

specifications or requirements defined. Use

of other fluids may lead to damage which

is not covered by the vehicle Warranty. See

Capacities and Specifications (page 297).

To top up the coolant level do the

compromise the performance of the

system. Have your vehicle checked

immediately.

following:

1. Remove the coolant reservoir cap.

2. Add coolant to the MAX mark, do not

overfill.

3. Replace the coolant reservoir cap. Turn

it clockwise until you feel a strong

resistance.

249

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Maintenance

WARNING: When lifting a

plastic-cased battery, excessive pressure

on the end walls could cause acid to flow

through the vent caps, resulting in

personal injury and damage to the

vehicle or battery. Lift the battery with a

battery carrier or with your hands on

opposite corners.

WARNING: Keep batteries out of

reach of children. Batteries contain

sulfuric acid. Avoid contact with skin,

eyes or clothing. Shield your eyes when

working near the battery to protect

against possible splashing of acid

solution. In case of acid contact with skin

or eyes, flush immediately with water for

a minimum of 15 minutes and get prompt

medical attention. If acid is swallowed,

call a physician immediately.

E170684

To avoid fluid contamination, the reservoir

cap must remain in place and fully tight,

unless you are adding fluid.

Only use fluid that meets Ford

specifications. See Capacities and

Specifications (page 297).

WARNING: Battery posts,

terminals and related accessories

contain lead and lead compounds. Wash

hands after handling.

WARNING: For vehicles with

Auto-Start-Stop the battery requirement

is different. You must replace the battery

with one of exactly the same

specification.

CLUTCH FLUID CHECK

The clutch and brake systems share the

same fluid reservoir. See Brake Fluid

Check (page 249).

The battery is in the engine compartment.

See Under Hood Overview (page 238).

CHANGING THE 12V B A T TERY

Your vehicle has a maintenance-free

battery. It does not require additional

water during service.

If the vehicle battery has a cover, make

sure you correctly install it after cleaning

or replacing the battery.

WARNING: Batteries normally

produce explosive gases which can

cause personal injury. Therefore, do not

allow flames, sparks or lighted

substances to come near the battery.

When working near the battery, always

shield your face and protect your eyes.

Always provide correct ventilation.

250

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Maintenance

For longer, trouble-free operation, keep the

Remove and Reinstall the Battery

top of the battery clean and dry and the

battery cables tightly fastened to the

battery terminals. If any corrosion is

present on the battery or terminals, remove

the cables from the terminals and clean

with a wire brush. You can neutralize the

acid with a solution of baking soda and

water.

To disconnect or remove the battery, do

the following:

1. Apply the parking brake and switch the

ignition off.

2. Switch all electrical equipment off, for

example lights and radio.

3. Wait a minimum of two minutes before

disconnecting the battery.

We recommend that you disconnect the

negative battery cable terminal from the

battery if you plan to store your vehicle for

an extended period.

Note: If you only disconnect the negative

battery cable terminal, make sure it is

isolated or placed away from the battery

terminal to avoid unintended connection or

arcing.

Note: The engine management system has

a power hold function and remains powered

for a period of time after you switch the

ignition off. This is to allow diagnostic and

adaptive tables to be stored. Disconnecting

the battery without waiting can cause

damage not covered by the vehicle

Warranty.

To maintain correct operation of the

battery management system, if you add

any electrical devices to your vehicle, do

not connect the ground connection directly

to the negative battery terminal. A

connection at the negative battery terminal

can cause inaccurate measurements of

the battery condition and potential

incorrect system operation.

Note: If you add electrical accessories or

components to your vehicle this may

adversely affect battery performance,

durability and the performance of other

electrical systems on your vehicle.

4. Disconnect the negative battery cable

terminal.

5. Disconnect the positive battery cable

terminal.

6. Remove the battery securing clamp.

7. Remove the battery.

8. To install, reverse the removal

procedure.

Note: Before reconnecting the battery,

make sure the ignition remains switched off.

Note: Make sure the battery cable terminals

are fully tightened.

If you replace the battery make sure it

matches the electrical requirements of

your vehicle.

If you disconnect or replace the vehicle

battery, you must reset the following

features:

If you disconnect or replace the battery

and your vehicle has an automatic

transmission, it must relearn its adaptive

strategy. Because of this, the transmission

may shift firmly when first driven. This is

normal operation while the transmission

fully updates its operation to optimum

shift feel.

•

Window bounce-back. See Opening

and Closing the Windows (page 79).

•

Clock Settings.

Pre-set radio stations.

251

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Maintenance

Battery Disposal

CHANGINGTHEFRONTWIPER

BLADES

Make sure that you dispose of

old batteries in an

E107998

environmentally friendly way.

Seek advice from your local authority

about recycling old batteries.

2

WASHER FLUID CHECK

When adding fluid, use a mixture of washer

fluid and water to help prevent freezing

and improve the cleaning capability. For

information on fluid dilution follow the

manufacturer's instructions.

1

E72899

1. Lift the wiper arm and then press the

wiper blade locking button.

Note: The reservoir supplies the front and

Note: Do not hold the wiper blade to lift the

rear washer systems.

wiper arm.

2. Remove the wiper blade.

CHECKING THE WIPER

BLADES

Note: Make sure that the wiper arm does

not spring back against the glass when the

wiper blade is not attached.

3. To install, reverse the removal

procedure.

Note: Make sure that the wiper blade locks

into place.

CHANGING THE REAR WIPER

BLADES

E142463

1. Lift the wiper arm.

Run the tip of your fingers over the edge of

the blade to check for roughness.

Clean the wiper blades with washer fluid

or water applied with a soft sponge or

cloth.

Note: Do not hold the wiper blade to lift the

wiper arm.

252

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Maintenance

2

3

2

1

E183236

E236623

2. Disengage the wiper blade from the

wiper arm.

Note: Make sure that the wiper arm does

not spring back against the glass when the

wiper blade is not attached.

1. Use a suitable tool, for example a

screwdriver, to carefully remove the

trim clip.

Note: Raise the center pin and then remove

the clip.

3. To install, reverse the removal

2. Remove the screws.

procedure.

Note: Make sure that the wiper blade locks

into place.

REMOVING A HEADLAMP

WARNING: Switch the lamps and

the ignition off. Failure to do so could

result in serious personal injury.

E249609

3. Place your hand below the headlamp

housing and lift the headlamp at the

center area to disengage the lower

fixing clip.

4. Carefully lift the headlamp up at the

front and rear to disengage it from the

fixing points.

253

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Maintenance

Note: Take care when removing the

headlamp. There are rupture points adjacent

to the securing screws that are designed to

separate under impact.

5. Slightly rotate the rear of the headlamp

toward the center of the vehicle so that

it clears the front fender.

1

6. Move the headlamp slightly backwards

to clear the radiator grille panel. Then

lift the headlamp straight upward.

7. Disconnect the electrical connector.

8. Remove the headlamp.

2

9. To install, reverse the removal

E237938

procedure.

1. Carefully cut the trim to access the

lamp release wing nut.

REMOVING A REAR LAMP

2. Turn the wing nut counterclockwise to

Brake Lamp, Rear Lamp and

release the lamp.

Direction Indicator

Note: You cannot fully remove the wing

nut.

E237937

E236624

3. Remove the lamp.

4. Disconnect the electrical connector.

5. To install, reverse the removal

procedure.

254

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Maintenance

Reversing Lamp

CHANGING A BULB

WARNING: Switch the lamps and

the ignition off. Failure to do so could

result in serious personal injury.

WARNING: Lamps and associated

components become hot when in use.

Let them cool down before you remove

them.

3

Use the correct specification bulb. See

Bulb Specification Chart (page 311).

Headlamp

E236638

You may have to remove the headlamp

assembly prior to replacing a bulb. See

Removing a Headlamp (page 253).

1. Open the liftgate.

2. Carefully remove the cover.

Reflector Headlamp

3. Turn the wing nut counterclockwise

and remove it.

A

E249611

A

Daytime running lamp.

E238054

4. Remove the lamp.

5. Disconnect the electrical connector.

6. To install, reverse the removal

procedure.

255

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Maintenance

A

B

C

E236599

E249637

3. Turn the bulb holder counterclockwise

A

B

Front direction indicator.

and remove it.

High beam headlamp and

Note: You cannot separate the bulb from

daytime running lamp.

the bulb holder.

C

Low beam headlamp.

4. To install, reverse the removal

procedure.

Low Beam Headlamp

1. Carefully remove the cover.

Note: Do not touch the bulb glass.

Projector Headlamp

A

E249634

E249612

2. Press the clip up to release the bulb

holder.

A

Daytime running lamp.

3. Remove the bulb holder by pulling it

straight out.

A

B

C

4. Remove the bulb by pulling it straight

out.

5. To install, reverse the removal

procedure.

Note: Do not touch the bulb glass.

E236599

High Beam Headlamp and Daytime

Running Lamp

A

B

C

Front direction indicator.

High beam headlamp.

Low beam headlamp.

1. Carefully remove the cover.

2. Disconnect the electrical connector.

256

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Maintenance

Low Beam Headlamp

Daytime Running Lamp

1. Carefully remove the cover.

These lamps have LEDs.

2. Disconnect the electrical connector.

Note: We recommend that you have LEDs

changed by an authorized dealer.

Front Direction Indicator

E249647

3. Turn the bulb holder counterclockwise

and remove it.

E236630

4. Remove the bulb.

1. Turn the bulb holder counterclockwise

and remove it.

5. To install, reverse the removal

procedure.

2. Press the bulb in and turn the bulb

Note: Do not touch the bulb glass.

counterclockwise to remove it.

High Beam Headlamp

1. Carefully remove the cover.

3. To install, reverse the removal

procedure.

LED Headlamp

A

E249660

E272995

2. Press the clip up to release the bulb

holder.

A

Daytime running lamp.

3. Remove the bulb holder by pulling it

straight out.

These lamps have LEDs.

4. Remove the bulb by pulling it straight

out.

Note: We recommend that you have LEDs

changed by an authorized dealer.

5. To install, reverse the removal

procedure.

Note: Do not touch the bulb glass.

257

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Maintenance

Note: Do not touch the bulb glass.

Front Fog Lamp

ST, ST Line and Vignale

All Vehicles - Excluding: ST, ST Line

and Vignale

E159695

1. Use a suitable tool, for example a

screwdriver, to carefully remove the

wheel arch liner fasteners. Pull the

wheel liner back toward the tire to gain

access to the bulb.

E273066

1. Use a suitable tool, for example a

screwdriver, to carefully remove the

housing cover.

2. Disconnect the electrical connector.

2

E273068

2. Remove the screws and the lamp.

3. Disconnect the electrical connector.

4. Turn the bulb holder counterclockwise

and remove it.

Note: You cannot separate the bulb from

E236628

the bulb holder.

5. To install, reverse the removal

3. Turn the bulb holder counterclockwise

and remove it.

procedure.

Note: You cannot separate the bulb from

the bulb holder.

4. To install, reverse the removal

procedure.

258

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Maintenance

Side Direction Indicator

E283366

4. Use a suitable tool, for example a

E283364

screwdriver, to push the housing cover

through the access hole and remove it.

1. Use a suitable tool, for example a

screwdriver, to carefully lever the mirror

glass from the lower outer edge and

remove it.

2. Unplug the connector from the rear

side of the glass.

E283367

5. Use a T10 Torx screwdriver to remove

the lamp body.

E283365

3. Use a suitable tool, for example a

screwdriver, to carefully press the two

housing cover clips and release them.

259

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Maintenance

2. Press the bulb in and turn the bulb

counterclockwise to remove it.

3. To install, reverse the removal

procedure.

Note: High series have LEDs.

Note: We recommend that you have LEDs

changed by an authorized dealer.

Rear Direction Indicator

E283430

2

1

6. Turn the bulb holder clockwise and

remove it.

7. Pull the bulb straight out.

8. To install, reverse the removal

procedure.

Note: Make sure that both mirror housing

cover clips lock into position.

Note: We recommend that you have bulbs

E236635

changed by an authorized dealer.

1. Turn the bulb holder counterclockwise

and remove it.

Rear Lamp

Remove the rear lamp assembly prior to

replacing any bulb. See Removing a Rear

Lamp (page 254).

2. Press the bulb in and turn the bulb

counterclockwise to remove it.

3. To install, reverse the removal

procedure.

Rear Lamp and Stoplamp

Reversing Lamp

2

1

2

E236636

1. Turn the bulb holder counterclockwise

and remove it.

E236634

1. Turn the bulb holder counterclockwise

and remove it.

2. Press the bulb in and turn the bulb

counterclockwise to remove it.

260

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Maintenance

3. To install, reverse the removal

procedure.

License Plate Lamp

These lamps have LEDs.

Note: We recommend that you have LEDs

changed by an authorized dealer.

High Mounted Stoplamp

These lamps have LEDs.

Note: We recommend that you have LEDs

changed by an authorized dealer.

Rear Fog Lamp

Access the underside of your vehicle

behind the rear wheel.

2

E236637

1. Turn the bulb holder counterclockwise

and remove it.

2. Press the bulb in and turn the bulb

counterclockwise to remove it.

3. To install, reverse the removal

procedure.

261

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Maintenance for Your Ford Fiesta 4 Door 2023

Popular Manuals