Get Wheels and Tires -> Changing a Road Wheel-Vehicles With-Spare Wheel Guide for Ford Fiesta 4 Door 2023

Wheels and Tires

How Temperature Affects Your Tire

If the tires are rotated, you need to reset

the system in order to relearn the positions

of the tire pressure sensors. The system

cannot tell which position a tire pressure

sensor is in, and assumes you have set the

tire pressures correctly.

Pressure

The tire pressure monitoring system

monitors tire pressure in each pneumatic

tire. While driving in a normal manner, a

typical passenger tire inflation pressure

may increase about 14–28 kPa (2–4 psi)

from a cold start situation. If the vehicle is

stationary overnight with the outside

temperature significantly lower than the

daytime temperature, the tire pressure may

decrease about 21 kPa (3 psi) for a drop of

30°F (17°C) in ambient temperature. This

lower pressure value may be detected by

the tire pressure monitoring system as

being significantly lower than the

Performing the Reset Procedure

1. Switch the ignition on.

2. Navigate to the tire monitor menu in

the information display. See

Information Messages (page 95).

3. Press and hold the OK button until a

confirmation message appears. If your

vehicle has a tire pressure monitoring

system reset button, press and hold

the button until a confirmation

message appears.

recommended inflation pressure and

activate the system warning light for low

tire pressure. If the low tire pressure

warning light is on, visually check each tire

to verify that no tire is flat. If one or more

tires are flat, repair as necessary. Check

the air pressure in the road tires. If any tire

is under-inflated, carefully drive the vehicle

to the nearest location where air can be

added to the tires. Inflate all the tires to

the recommended inflation pressure.

CHANGING A ROAD WHEEL -

VEHICLES WITH: SPARE

WHEEL

Vehicles With a Spare Wheel

Tire Pressure Monitoring System

WARNING: Do not fit more than

one spare wheel on your vehicle at any

one time.

Reset Procedure

Overview

You must carry out the system reset

procedure after each tire replacement or

adjustment of the tire pressures.

To maintain your vehicle load carrying

capability, your vehicle may require

different tire pressures in the front

compared to the rear. In these cases, the

system illuminates the warning lamp at

different pressures for the front and rear

tires.

WARNING: Do not carry out any

tire repairs on a spare wheel.

WARNING:If you are not sure what

type of spare wheel your vehicle has, do

not exceed 80 km/h (50 mph).

WARNING: Only fit snow chains to

specified tires.

If the spare wheel is the same type and

size as your vehicle road wheel, you can fit

the spare wheel and continue to drive in

the normal manner.

278

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Wheels and Tires

If the spare wheel is not the same type and

1. Turn the spare wheel securing nut

counterclockwise and remove it.

Remove the wheel from the spare

wheel well.

size as your vehicle road wheel, it has a

label showing the maximum driving speed

limit.

Refer to the following information before

changing the road wheel.

Note: Your vehicle may exhibit some

different driving characteristics if you fit the

spare wheel.

Note: The ground clearance of your vehicle

may be reduced when the spare wheel is

fitted. Take care when parking next to a

curb.

2

Note: The spare wheel is located under the

floor cover in the luggage compartment.

Note: If the spare wheel is fitted to your

vehicle, do not drive through an automatic

car wash.

Note: If the spare wheel is fitted to your

vehicle, drive the shortest distance possible.

1

3

E178548

2. Turn the vehicle jack securing bolt

counterclockwise and remove it.

3. Turn the vehicle jack screw clockwise

to remove the vehicle jack handle and

lug nut tool from the vehicle jack.

E178549

279

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Wheels and Tires

WARNING: Never place anything

between the vehicle jack and the ground.

WARNING: Never place anything

between the vehicle jack and your

vehicle.

WARNING: Use a jack with a

minimum lifting capacity of 1,500 kg

(3,307 lb) and a lifting plate with a

minimum diameter of 80 mm (3.1 in).

WARNING: Do not work on your

vehicle when the jack is the only support.

If the vehicle slips off the jack, you or

someone else could be seriously injured.

E245204

4. Unfold the vehicle jack handle and the

hexagonal end into the correct position

prior to use. Use the hexagonal end to

operate the vehicle jack screw and to

remove the lug nuts.

WARNING:No person should place

any portion of their body under a vehicle

that is supported by a jack.

Note: Use the hook at the hexagonal end

WARNING: Do not get under a

vehicle that is only supported by a

vehicle jack.

to remove the wheel trim.

Vehicles Without a Spare Wheel

Vehicles without a spare wheel are fitted

with a temporary mobility kit. See Tire

Sealant and Inflator Kit (page 268).

Note: Vehicles with a temporary mobility

kit do not have a spare wheel, vehicle jack

or wheel brace.

Vehicle Jack

E166722

WARNING: The jack supplied with

this vehicle is only intended for changing

wheels. Do not use the vehicle jack other

than when you are changing a wheel in

an emergency.

Workshop Type Hydraulic Trolley Jack

WARNING: Use a jack with a

minimum lifting capacity of 1,500 kg

(3,307 lb) and a lifting plate with a

minimum diameter of 80 mm (3.1 in).

WARNING: Check that the vehicle

jack is not damaged or deformed and

the thread is lubricated and clean.

We recommend you use a workshop type

hydraulic trolley jack for changing between

summer and winter tires.

280

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Wheels and Tires

Refer to vehicle jack manufacturer's

instructions.

Jacking and Lifting Points

WARNING: You must use the

specified jacking points.

E93020

A

B

E283868

A

B

Emergency use only.

Maintenance.

281

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Wheels and Tires

A

E93184

Indentations in the sills show the location

of the jacking points.

All Vehicles - Excluding: Active, ST and

ST Line

E93020

Active, ST and ST Line

E283869

E92932

282

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Wheels and Tires

Removing the Wheel Trim

WARNING: If your vehicle has a

manual transmission, shift into first or

reverse gear. If your vehicle has an

automatic transmission, shift into park

(P).

WARNING: Make sure all

passengers are out of your vehicle.

WARNING: Chock the diagonally

opposite wheel to the punctured tire with

an appropriate wheel block or wheel

chock.

WARNING: Do not work on your

vehicle when the jack is the only support.

If the vehicle slips off the jack, you or

someone else could be seriously injured.

E285279

1. Unfold the lug nut wrench.

2. Use the tongue on the lug nut wrench

to remove the wheel trim.

Removing a Road Wheel

E166722

WARNING: Park your vehicle in

such a position that neither the traffic

nor you are hindered or endangered.

WARNING: Make sure that the

vehicle jack is vertical to the jacking point

and the base is flat on the ground.

WARNING: Park your vehicle so

that you do not obstruct the flow of

traffic or place yourself in any danger and

set up a warning triangle.

1. Install the locking lug nut key.

WARNING: Make sure that your

vehicle is on firm and level ground with

the front wheels pointing straight ahead.

WARNING: Switch the ignition off

and apply the parking brake.

283

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Wheels and Tires

correct metal-to-metal contact at the

wheel mounting surfaces can cause the

wheel nuts to loosen and the wheel to

come off while your vehicle is in motion,

resulting in loss of vehicle control,

personal injury or death.

1

WARNING: Make sure that the

arrows on directional tires point in the

direction of rotation when your vehicle

is moving forward. If you have to fit a

spare tire with the arrows pointing in the

opposite direction have the tire refitted

as soon as possible.

2

WARNING: Use only approved

wheel and tire sizes. Using other sizes

could damage your vehicle and will make

the National Type Approval invalid.

WARNING: Make sure there is no

grease or oil on the threads or the

surface between the wheel lugs and

nuts. This can cause the lug nuts to

loosen while driving.

E181745

2. Loosen the lug nuts.

3. Raise your vehicle until the tire is clear

of the ground.

WARNING: Do not fit run flat tires

on vehicles that were not originally fitted

with them. Contact an authorized dealer

for more details about compatibility.

4. Remove the lug nuts and the road

wheel.

Note: Do not lay alloy wheels face down

on the ground. This may damage the paint.

Installing a Road Wheel

WARNING: Do not install alloy

wheels using lug nuts designed for use

with steel wheels.

WARNING: When you install a

wheel, always remove any corrosion, dirt

or foreign materials present on the

mounting surfaces of the wheel or the

surface of the wheel hub, brake drum or

brake disc that contacts the wheel. Make

sure to secure any fasteners that attach

the rotor to the hub so they do not

WARNING: Have the lug nuts

checked for tightness and the tire

pressure checked as soon as possible.

WARNING: Only use the specific

lug nuts and wheels supplied with your

vehicle. If in doubt, contact an authorized

dealer.

interfere with the mounting surfaces of

the wheel. Installing wheels without

284

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Wheels and Tires

Note: The lug nuts of alloy wheels and

TIRE PRESSURES - 1.0L

ECOBOOST™, MANUAL

TRANSMISSION

The recommended tire inflation pressures

are on the tire information label on the

driver side B-pillar.

spoked steel wheels can also be used for

the steel spare wheel for a short time

(maximum two weeks).

Note: Make sure that the cones on the lug

nuts are against the wheel.

1. Install the wheel.

2. Install the lug nuts finger tight.

3. Install the locking lug nut key.

Check all tire pressures when they are cold,

at least once every two weeks.

Note: You may need to remove the spare

wheel from the spare wheel well to check

the tire pressure.

3

A

B

C

D

E

1

2

x x x x x x

x x x x x x x x

x x x x x x

x x x x x x x x

x x

4

F

I

H

G

E90589

E254054

4. Install all of the lug nuts and partially

tighten them in the sequence shown.

5. Lower your vehicle and remove the

A

B

C

D

E

F

Tire size.

Vehicle model.

Front tire pressure.

Rear tire pressure.

Vehicle load.

vehicle jack.

6. Fully tighten all of the lug nuts in the

sequence shown. See Wheels and

Tires (page 268).

7. Install the wheel trim.

Measure unit.

G

H

I

Spare wheel tire pressure.

Intended constant vehicle speed.

Spare wheel tire size.

285

Fiesta (CE1) Vehicles Built From: 06-01-2020 Vehicles Built Up To: 19-04-2020, CG3654en enGBR, Edition date: 201909, Second-Printing

Wheels and Tires -> Changing a Road Wheel-Vehicles With-Spare Wheel for Your Ford Fiesta 4 Door 2023

Popular Manuals