Get Wheels and Tires Guide for Ford Focus 4 Door 2023

Wheels and Tires

If your vehicle does not have a spare wheel

GENERAL INFORMATION

The recommended tire inflation pressures

are on the tire information label on the

driver side B-pillar.

Check and set the tire pressure at the

ambient temperature in which you are

intending to drive your vehicle and when

the tires are cold. See Tire Pressures

(page 457).

it has a tire sealant and inflator kit. The kit

is in the luggage compartment. Only use

the kit supplied with your vehicle.

Note: The kit can only temporarily repair

one tire puncture with a maximum puncture

size of up to 6 mm (0.24 in).

A

B

C

D

Note: Check your tire pressures regularly to

optimize fuel economy.

Only use approved wheel and tire sizes.

Using other sizes could damage your

vehicle and could make the National Type

Approval invalid.

Installation of any tires that are not the

original equipment tire size can cause the

speedometer to display incorrect vehicle

speed.

TIRESEALANTANDINFLATOR

KIT

G

F

E

WARNING: Do not use the inflator

kit on run flat tires. This could cause loss

of vehicle control.

E257262

A

B

C

D

E

Pressure Gauge.

Sealant bottle access cap.

Warning label.

Power switch.

Sealant bottle.

WARNING: Depending on the type

and extent of tire damage, some tires

can only be partially sealed or not sealed

at all. Loss of tire pressure can affect

vehicle handling, leading to loss of

vehicle control.

F

G

Tire inflation pipe.

WARNING: Do not use the kit on a

previously damaged tire, for example

when it has been driven under inflated.

This could cause loss of vehicle control,

personal injury or death.

12 volt DC power point

connector.

Note: Make sure you regularly check the

expiry date on the sealant bottle.

444

Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing

Wheels and Tires

If the low tire pressure warning

To temporarily repair a punctured tire, do

lamp illuminates do the

following:

the following:

1. Gradually reduce the vehicle speed and

stop your vehicle as soon as it is safe

to do so.

2. Apply the parking brake and switch the

ignition off.

3. Check for a punctured tire.

Note: Do not remove objects, for example

nails or screws from a punctured tire.

Using the Tire Sealant and Inflator

Kit

WARNING: Check the sidewall of

the tire prior to inflation. If there are any

cracks, bumps or similar damage, do not

attempt to inflate the tire. This could

cause personal injury.

E257263

1. Release the tire inflation pipe and the

12 volt DC power point connector from

the underside of the compressor.

WARNING: Watch the sidewall of

the tire when inflating. If any cracks,

bumps or similar damage appears,

switch the compressor off and let the air

out by means of the pressure relief valve.

Do not continue driving with this tire. This

could cause loss of vehicle control.

WARNING: Do not stand directly

beside the tire while the compressor is

operating. This could cause personal

injury if the tire bursts.

E257264

WARNING: Do not leave the kit

unattended when it is in use. Failure to

follow this instruction could result in

personal injury or death.

2. Turn the sealant bottle access cap

counterclockwise and remove it.

WARNING: Do not keep the

compressor operating for more than 10

minutes. This could cause the

compressor to malfunction causing

serious personal injury.

445

Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing

Wheels and Tires

E257006

E256963

3. Remove the sealant bottle cap. Do not

pierce or remove the seal.

5. Remove the tire valve dust cap and

attach the tire inflation pipe.

E257022

6. Plug the 12 volt DC power point

connector into the 12 volt DC socket.

See Auxiliary Power Points (page

188).

E257265

4. Attach the sealant bottle to the

compressor. Turn the sealant bottle

clockwise until you feel a strong

resistance.

7. Start the engine.

Note: Attaching the sealant bottle to the

compressor pierces the seal. Do not loosen

the bottle as sealant could escape.

446

Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing

Wheels and Tires

11.

Disconnect the tire inflation pipe and

the 12 volt DC power point connector.

Note: Do not remove the sealant bottle

from the compressor.

12. Reinstall the tire valve dust cap.

13. Place the warning label on the

steering wheel and correctly stow the

kit.

E257266

8. Switch the compressor on.

E257942

14. Immediately drive your vehicle for

3–10 km (2–6 mi). Do not exceed

80 km/h (50 mph).

E257121

9. Inflate the tire to between 2–3 bar

(29–44 psi).

Note: If the tire pressure does not reach

1.8 bar (26 psi) within 10 minutes, the tire

could be damaged beyond a temporary

repair. Have your vehicle immediately

checked. Do not drive your vehicle.

10. When the tire reaches the

recommended tire pressure of

E257121

between 2–3 bar (29–44 psi), switch

the compressor and the ignition off.

447

Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing

Wheels and Tires

15. After driving between 3–10 km

•

Regularly check the tire pressure until

(2–6 mi), stop your vehicle and

recheck the tire pressure. See Tire

Pressures (page 457).

the sealed tire is repaired or replaced

by a tire specialist. Before the tire is

removed from the rim, you must inform

the tire specialist that the tire contains

sealant.

Note: If the tire pressure has dropped to

1.8 bar (26 psi) or below, the tire could be

damaged beyond a temporary repair. Have

your vehicle immediately checked. Do not

drive your vehicle.

•

Take the kit to an authorized dealer to

have the sealant bottle and the tire

inflation pipe replaced.

Note: If the tire pressure has dropped but

is still above 1.8 bar (26 psi), use the kit to

inflate the tire again.

TIRE CARE

Note: Front tires shown on the left side of

After Using the Tire Sealant and

Inflator Kit

the diagram.

Non-directional tires

WARNING: If you experience heavy

vibrations, unsteady steering behavior or

noises while driving, reduce your speed

gradually and stop your vehicle as soon

as it is safe to do so. Recheck the tire and

its pressure. If the tire pressure is less

than 1.3 bar (18.9 psi) or if there are any

cracks, bumps or similar damage visible,

do not continue driving with this tire. This

could cause loss of vehicle control.

E142547

The kit only provides temporary mobility.

Regulations concerning tire repair or

replacement after using the kit could differ

from country to country. We recommend

you consult a tire specialist.

Directional tires

After using the kit:

•

Do not drive your vehicle more than

200 km (124 mi) before repairing or

replacing the punctured tire.

•

Inform all other users of your vehicle

that a tire was sealed using the kit.

Make them aware of the special driving

conditions that must be observed.

E70415

448

Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing

Wheels and Tires

To make sure the front and rear tires of

We recommend that you use winter or

all-season tires carrying this symbol when

the temperature is 7°C (45°F) or lower, or

in snow and ice conditions.

Inflate the winter tires to the same tire

pressures as those listed in the tire

pressures table. See Tire Pressures (page

457).

your vehicle wear evenly and last longer,

we recommend that you swap the tires

from front to rear and vice versa at regular

intervals between 5,000 km (3,000 mi)

and 10,000 km (6,000 mi).

WARNING: Do not scrub the

sidewalls of the tires when you are

parking.

WARNING: Snow tires must be the

same size, load index and speed rating

as those originally provided by Ford. Use

of any tire or wheel not recommended

by Ford can affect the safety and

performance of your vehicle, which could

result in an increased risk of loss of

control, vehicle rollover, personal injury

and death. Additionally, the use of

non-recommended tires and wheels can

cause steering, suspension, axle, transfer

case or power transfer unit failure.

Follow the Ford recommended tire

inflation pressure found on the Safety

Compliance Certification Label (on the

door hinge pillar, door latch post or the

door edge that meets the door latch

post, next to the driver seat), or Tire

Label on the B-Pillar or the edge of the

driver door. Failure to follow the tire

pressure recommendations can cause

uneven treadwear patterns and

If you have to mount a curb, do so slowly

and approach it with the wheels at

right-angles to the curb.

Examine the tires regularly for cuts, foreign

objects and uneven wear of the tread.

Uneven wear could mean that the wheel

alignment is outside specification.

Check the tire pressures (including the

spare) when cold, every two weeks.

USING SUMMER TIRES

The original equipment tires on your vehicle

are designed to optimize its performance

in dry or wet summer road conditions.

They are not designed for winter use. Do

not use the summer tires with snow chains.

USING WINTER TIRES

adversely affect the way your vehicle

handles.

USING SNOW CHAINS -

EXCLUDING: ACTIVE/ST

WARNING:Do not exceed 50 km/h

(30 mph). Failure to follow this

instruction could result in the loss of

control of your vehicle, personal injury or

death.

E278852

449

Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing

Wheels and Tires

USING SNOW CHAINS -

ACTIVE

WARNING:Do not use snow chains

on snow-free roads.

WARNING: Only fit snow chains to

WARNING:Do not exceed 50 km/h

specified tires.

(30 mph). Failure to follow this

instruction could result in the loss of

control of your vehicle, personal injury or

death.

WARNING: If your vehicle is fitted

with wheel trims, remove them before

fitting snow chains.

WARNING:Do not use snow chains

Only use snow chains on the front wheels.

on snow-free roads.

Only use snow chains on the following

specified tire sizes:

WARNING: Only fit snow chains to

specified tires.

•

195/65R16.

Do not use snow chains greater

than 7 mm (0.3 in).

205/60R16.

•

WARNING: If your vehicle is fitted

with wheel trims, remove them before

fitting snow chains.

•

Do not use snow chains greater

Only use snow chains on the front wheels.

than 10 mm (0.4 in).

•

Do not use snow chains greater

than 8 mm (0.3 in) for five spoke

steel wheels.

Only use snow chains on the following

specified tire sizes:

•

215/55R17.

Do not use snow chains greater

than 10 mm (0.4 in).

Maintain correct tire pressures. See Tire

•

Pressures (page 457).

Maintain correct tire pressures. See Tire

Vehicles with Stability Control

Pressures (page 457).

When stability control is on, your vehicle

may exhibit some unusual driving

characteristics. To reduce this, switch

traction control off. See Using Stability

Control (page 255).

Vehicles with Stability Control

When stability control is on, your vehicle

may exhibit some unusual driving

characteristics. To reduce this, switch

traction control off. See Using Stability

Control (page 255).

Note: The anti-lock brake system continues

to correctly operate.

Note: The anti-lock brake system continues

to correctly operate.

450

Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing

Wheels and Tires

USING SNOW CHAINS - ST

WARNING: Do not carry out any

tire repairs on a spare wheel.

WARNING:Do not exceed 50 km/h

(30 mph). Failure to follow this

instruction could result in the loss of

control of your vehicle, personal injury or

death.

WARNING: Do not switch off

stability control or select sport mode,

when using a temporary spare wheel or

after inflating a tire using the temporary

mobility kit.

WARNING:Do not use snow chains

If a tire deflates when your vehicle is

moving, do the following:

on snow-free roads.

WARNING: Only fit snow chains to

•

Firmly hold the steering wheel.

Avoid heavy braking.

Gradually reduce the vehicle speed and

stop your vehicle as soon as it is safe

to do so.

specified tires.

WARNING: If your vehicle is fitted

with wheel trims, remove them before

fitting snow chains.

•

Fully apply the parking brake.

Switch the ignition off.

Only use snow chains on the front wheels.

Only use snow chains on the following

The spare wheel, vehicle jack, towing eye,

lug nut tool and wheel trim remover are in

the luggage compartment under the floor

covering or in the side panel.

If the spare wheel is exactly the same type

and size as the other fitted road wheels,

you can replace the existing road wheel

with the spare wheel and continue to drive

in the normal manner. We recommend that

you have the damaged road wheel and tire

repaired or replaced as soon as possible.

specified tire sizes:

•

215/50R17.

Do not use snow chains greater

than 7 mm (0.3 in).

•

Maintain correct tire pressures. See Tire

Pressures (page 457).

Vehicles with Stability Control

When stability control is on, your vehicle

may exhibit some unusual driving

characteristics. To reduce this, switch

traction control off. See Using Stability

Control (page 255).

Dissimilar Spare Wheel and Tire

Assembly Information

Note: The anti-lock brake system continues

WARNING: Failure to follow these

guidelines could result in an increased

risk of loss of vehicle control, injury or

death.

to correctly operate.

CHANGING A ROAD WHEEL

WARNING:If you are not sure what

type of spare wheel your vehicle has, do

not exceed 80 km/h (50 mph).

WARNING: Do not fit more than

one spare wheel on your vehicle at any

one time.

451

Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing

Wheels and Tires

If the spare wheel is different to the other

•

Do not use snow chains on the end of

fitted road wheels, it may have a warning

label with the appropriate maximum speed

limit. Drive cautiously when using a

your vehicle with the dissimilar spare

tire.

•

Do not use more than one dissimilar

dissimilar spare wheel and tire assembly.

spare tire at a time.

A dissimilar spare wheel and tire is for

temporary use only. Drive the shortest

distance possible and have the damaged

road wheel and tire repaired or replaced

as soon as possible. If the dissimilar spare

wheel or tire is damaged, it must be

replaced.

If you use a dissimilar spare wheel and tire

assembly, this can lead to impairment of

the following:

Do not use commercial car washing

equipment.

Full-size Dissimilar Spare Wheel With

a Label on the Wheel

The label on the wheel states: THIS

WHEEL AND TIRE ASSEMBLY FOR

TEMPORARY USE ONLY.

When driving with this type of a dissimilar

spare wheel:

•

Handling, stability and braking

•

Do not exceed the maximum speed

shown on the label.

Do not load your vehicle beyond

maximum vehicle load rating listed on

the safety compliance label.

performance.

•

Comfort and noise.

Ground clearance and parking at curbs.

Winter weather driving capability.

Wet weather driving capability.

All-wheel driving capability.

•

Do not tow a trailer.

Do not use snow chains on the end of

your vehicle with the dissimilar spare

tire.

A dissimilar spare wheel and tire assembly

is different in size and appearance from

the road wheels and tires and can be one

of three types:

•

Do not use more than one dissimilar

spare tire at a time.

Do not use commercial car washing

equipment.

T-type Mini-spare Wheel

The spare tire has the letter T preceding

the tire size, for example T125/80R15 and

may have Temporary Use Only molded in

the sidewall.

Full-size Dissimilar Spare Wheel

Without a Label on the Wheel

If the spare wheel is exactly the same type

and size as the other fitted road wheels,

you can replace the existing road wheel

with the spare wheel and continue to drive

in the normal manner.

When driving with this type of a dissimilar

spare wheel:

•

Do not exceed the maximum speed

shown on the label.

Do not load your vehicle beyond

maximum vehicle load rating listed on

the safety compliance label.

•

Do not tow a trailer.

452

Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing

Wheels and Tires

Removing the Spare Wheel,

Vehicle Jack and Lug Nut Tool

1

2

3

E178548

2. Turn the vehicle jack securing bolt

counterclockwise and remove it.

E178549

3. Turn the vehicle jack screw

counterclockwise to remove the vehicle

jack handle and lug nut tool from the

vehicle jack.

1. Turn the securing nut counterclockwise

and remove it. Remove the wheel from

the spare wheel well.

E245204

453

Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing

Wheels and Tires

4. Unfold the vehicle jack handle and the

hexagonal end into the correct position

prior to use. Use the hexagonal end to

operate the vehicle jack screw and to

remove the lug nuts.

WARNING: Do not work on your

vehicle when the jack is the only support

as your vehicle could slip off the jack.

Failure to follow this instruction could

result in personal injury or death.

Assembling the Lug Nut Tool

WARNING:No person should place

any portion of their body under a vehicle

that is supported by a jack.

Fully unfold the vehicle jack handle and

lug nut tool.

Vehicles Without a Spare Wheel

Vehicles without a spare wheel have a

temporary mobility kit. See Tire Sealant

and Inflator Kit (page 444).

WARNING: Do not get under a

vehicle that is only supported by a

vehicle jack.

Removing the Wheel Trim (I f E quipped)

Use the hook on the vehicle jack handle

and lug nut tool to remove the wheel trim.

Note: Make sure that you pull the wheel

trim remover at right angles to the trim.

Vehicle Jack

E166722

WARNING: Check that the vehicle

jack is not damaged or deformed and

the thread is lubricated and clean.

Workshop Type Hydraulic Trolley Jack

WARNING: Use a jack with a

minimum lifting capacity of 1,500 kg

(3,307 lb) and a lifting plate with a

minimum diameter of 80 mm (3.1 in).

WARNING: Never place anything

between the vehicle jack and the ground.

WARNING: Never place anything

between the vehicle jack and your

vehicle.

We recommend you use a workshop type

hydraulic trolley jack for changing between

summer and winter tires.

WARNING: Use a jack with a

minimum lifting capacity of 1,500 kg

(3,307 lb) and a lifting plate with a

minimum diameter of 80 mm (3.1 in).

WARNING: The jack supplied with

this vehicle is only intended for changing

wheels. Do not use the vehicle jack other

than when you are changing a wheel in

an emergency.

454

Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing

Wheels and Tires

E283869

2. Carefully position the vehicle jack onto

the vehicle jacking point.

E93020

3. Place the hexagonal end of the vehicle

jack handle and lug tool onto the

vehicle jack.

Refer to vehicle jack manufacturer's

instructions.

4. Turn the vehicle jack handle clockwise

Vehicle Jacking Points

to raise the vehicle.

Removing a Road Wheel

WARNING: Use only the specified

jacking points. If you use other positions,

you may damage the body, steering,

suspension, engine, braking system or

the fuel lines.

WARNING: Park your vehicle in

such a position that neither the traffic

nor you are hindered or endangered.

WARNING: Park your vehicle so

that you do not obstruct the flow of

traffic or place yourself in any danger and

set up a warning triangle.

WARNING: Make sure that your

vehicle is on firm and level ground with

the front wheels pointing straight ahead.

E269166

WARNING: Switch the ignition off

1. Locate the vehicle jacking points. Small

arrow-shaped marks indicate the

locations.

and apply the parking brake.

WARNING: If your vehicle has a

manual transmission, shift into first or

reverse gear. If your vehicle has an

automatic transmission, shift into park

(P).

455

Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing

Wheels and Tires

Installing a Road Wheel

WARNING: Make sure all

passengers are out of your vehicle.

WARNING: When you install a

wheel, always remove any corrosion, dirt

or foreign materials present on the

mounting surfaces of the wheel or the

surface of the wheel hub, brake drum or

brake disc that contacts the wheel. Make

sure to secure any fasteners that attach

the rotor to the hub so they do not

interfere with the mounting surfaces of

the wheel. Installing wheels without

correct metal-to-metal contact at the

wheel mounting surfaces can cause the

wheel nuts to loosen and the wheel to

come off while your vehicle is in motion,

resulting in loss of vehicle control,

personal injury or death.

WARNING: Make sure that the

vehicle jack is vertical to the jacking point

and the base is flat on the ground.

WARNING: Secure the diagonally

opposite wheel with an appropriate

block or wheel chock.

1

WARNING: Make sure there is no

grease or oil on the threads or the

surface between the wheel lugs and

nuts. This can cause the lug nuts to

loosen while driving.

WARNING: Use only approved

wheel and tire sizes. Using other sizes

could damage your vehicle and will make

the National Type Approval invalid.

2

WARNING: Do not fit run flat tires

on vehicles that were not originally fitted

with them. Contact an authorized dealer

for more details about compatibility.

E181745

1. If your vehicle has locking lug nuts,

install the locking lug nut tool and

loosen the locking lug nut first.

WARNING: Do not install alloy

wheels using lug nuts designed for use

with steel wheels.

2. Loosen the lug nuts.

WARNING: Have the lug nuts

checked for tightness and the tire

pressure checked as soon as possible.

3. Raise your vehicle until the tire is clear

of the ground.

4. Remove the lug nuts and the wheel.

Note: Do not lay alloy wheels face down

on the ground. This may damage the paint.

456

Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing

Wheels and Tires

7. Carefully install the wheel trim.

TIRE PRESSURES -

EXCLUDING: ACTIVE/ST

The recommended tire inflation pressures

are on the tire information label on the

driver side B-pillar.

Check all tire pressures when they are cold,

at least once every two weeks.

E145950

Note: You may need to remove the spare

wheel from the spare wheel well to check

the tire pressure.

1. Inspect the wheel pilot bore (A) and

mounting surface prior to installation.

Remove any visible corrosion or loose

particles.

A

B

C

D

E

2. Install the wheel.

3. Install the lug nuts finger tight.

x x x x x x

Note: Make sure that the cones on the lug

nuts are against the wheel.

x x x x x x x x

x x x x x x

x x x x x x x x

x x

1

F

I

H

G

4

3

E254054

A

B

C

D

E

F

G

H

I

Tire size.

Vehicle model.

Front tire pressure.

Rear tire pressure.

Vehicle load.

Measure unit.

Spare wheel tire pressure.

Intended constant vehicle speed.

Spare wheel tire size.

2

5

E75442

4. Partially tighten the lug nuts in the

sequence shown.

5. Lower your vehicle and remove the

vehicle jack.

6. Fully tighten the lug nuts in the

sequence shown. See Lug Nuts (page

462).

457

Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing

Wheels and Tires

Up to 160 km/h (100 mph)

Tire Size

Normal Load

Full Load

Front

Rear

Front

Rear

bar (psi)

2.6 (38)

2.3 (33)

bar (psi)

2.6 (38)

2.3 (33)

2.1 (30)

bar (psi)

2.6 (38)

2.5 (36)

bar (psi)

3.1 (45)

2.8 (41)

205/60R16

215/50R17

235/40R18

Continuous Speed in Excess of 160 km/h (100 mph) or With Trailer Towing up to

100 km/h (62 mph)

Normal Load

Full Load

Tire Size

Front

Rear

Front

Rear

bar (psi)

2.6 (38)

2.3 (33)

bar (psi)

2.6 (38)

2.3 (33)

2.1 (30)

bar (psi)

2.6 (38)

2.5 (36)

bar (psi)

3.1 (45)

2.9 (42)

205/60R16

215/50R17

235/40R18

Temporary Spare Wheel(If Equipped)

WARNING: Do not switch off stability control or select sport mode, when using

a temporary spare wheel or after inflating a tire using the temporary mobility kit.

Tire Size

T125/70R16

T125/80R16

bar (psi)

4.2 (60)

Do not exceed the maximum speed stated on the label attached to the temporary spare

wheel.

458

Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing

Wheels and Tires

TIRE PRESSURES - ACTIVE

A

B

C

D

E

The recommended tire inflation pressures

are on the tire information label on the

driver side B-pillar.

x x x x x x

Check all tire pressures when they are cold,

at least once every two weeks.

x x x x x x x x

Note: You may need to remove the spare

wheel from the spare wheel well to check

the tire pressure.

x x x x x x

x x x x x x x x

x x

F

I

H

G

E254054

A

B

C

D

E

F

Tire size.

Vehicle model.

Front tire pressure.

Rear tire pressure.

Vehicle load.

Measure unit.

G

H

I

Spare wheel tire pressure.

Intended constant vehicle speed.

Spare wheel tire size.

Up to 160 km/h (100 mph)

Normal Load

Full Load

Tire Size

Front

Rear

Front

Rear

bar (psi)

2.3 (33)

bar (psi)

2.3 (33)

bar (psi)

2.4 (35)

2.5 (36)

bar (psi)

2.8 (41)

215/55R17

215/50R18

459

Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing

Wheels and Tires

Continuous Speed in Excess of 160 km/h (100 mph) or With Trailer Towing up to

100 km/h (62 mph)

Normal Load

Full Load

Tire Size

Front

Rear

Front

Rear

bar (psi)

2.3 (33)

bar (psi)

2.3 (33)

bar (psi)

2.4 (35)

2.5 (36)

bar (psi)

2.8 (41)

215/55R17

215/50R18

Temporary Spare Wheel^{(If Equipped)}

WARNING: Do not switch off stability control or select sport mode, when using

a temporary spare wheel or after inflating a tire using the temporary mobility kit.

Tire Size

T125/70R16

T125/80R16

bar (psi)

4.2 (60)

Do not exceed the maximum speed stated on the label attached to the temporary spare

wheel.

TIRE PRESSURES - ST

The recommended tire inflation pressures

are on the tire information label on the

driver side B-pillar.

Check all tire pressures when they are cold,

at least once every two weeks.

Note: You may need to remove the spare

wheel from the spare wheel well to check

the tire pressure.

460

Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing

Wheels and Tires

A

B

C

D

E

F

G

H

I

Tire size.

Vehicle model.

Front tire pressure.

Rear tire pressure.

Vehicle load.

A

B

C

D

E

x x x x x x

x x x x x x x x

Measure unit.

x x x x x x

x x x x x x x x

x x

Spare wheel tire pressure.

Intended constant vehicle speed.

Spare wheel tire size.

F

I

H

G

E254054

Up to 160 km/h (100 mph)

Tire Size

Normal Load

Full Load

Front

Rear

Front

Rear

bar (psi)

2.3 (33)

2.4 (35)

bar (psi)

2.3 (33)

2.4 (35)

bar (psi)

2.4 (35)

2.7 (39)

bar (psi)

2.4 (35)

2.7 (39)

215/50R17

235/40R18

235/35R19

Continuous Speed in Excess of 160 km/h (100 mph) or With Trailer Towing up to

100 km/h (62 mph)

Normal Load

Full Load

Tire Size

Front

Rear

Front

Rear

bar (psi)

3 (44)

bar (psi)

2.7 (39)

2.4 (35)

2.7 (39)

bar (psi)

2.4 (35)

bar (psi)

2.9 (42)

2.5 (36)

2.9 (42)

215/50R17

235/40R18

235/35R19

2.6 (38)

3 (44)

461

Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing

Wheels and Tires

Temporary Spare Wheel(If Equipped)

WARNING: Do not switch off stability control or select sport mode, when using

a temporary spare wheel or after inflating a tire using the temporary mobility kit.

Tire Size

T125/70R17

bar (psi)

4.2 (60)

Do not exceed the maximum speed stated on the label attached to the temporary spare

wheel.

LUG NUTS

Lug Nut Torque

Nm ( lb.ft)

135 (100)

Locking Lug Nuts

You can obtain a replacement locking lug

nut key and replacement locking lug nuts

from an authorized dealer using the

reference number certificate.

462

Focus (CGE) Vehicles Built From: 15-03-2021, CG3784en enGBR, Edition date: 202012, First-Printing

Wheels and Tires for Your Ford Focus 4 Door 2023

Popular Manuals