Get Driving Aids -> Pre-Collision Assist Vehicles With 4.2 Inch Instrument Cluster Display Screen Guide for Ford Kuga SUV 2020

Driving Aids

Note: The system only indicates the

PRE-COLLISION ASSIST -

VEHICLES WITH: 4.2 INCH

INSTRUMENT CLUSTER

DISPLAY SCREEN

efficiency level for the current trip. The

system resets each time you switch the

ignition on.

Eco Mode System Display

You can view the instantaneous efficiency

level or the trip summary in the information

display.

1. Press the menu button on the steering

wheel to enter the information display

main menu.

WARNING: You are responsible for

controlling your vehicle at all times. The

system is designed to be an aid and does

not relieve you of your responsibility to

drive with due care and attention. Failure

to follow this instruction could result in

the loss of control of your vehicle,

personal injury or death.

2. Select Display settings.

3. Select Eco coach.

4. Select a setting and press the OK

WARNING: The system does not

operate during hard acceleration or

steering. Failure to take care may lead

to a crash or personal injury.

button.

Instantaneous Efficiency Level

The display circle illuminates as the

instantaneous efficiency level increases.

The level continuously updates to indicate

the efficiency level for the current trip.

WARNING: The system may fail or

operate with reduced function during

cold and severe weather conditions.

Snow, ice, rain, spray and fog can

adversely affect the system. Keep the

front camera and radar free of snow and

ice. Failure to take care may result in the

loss of control of your vehicle, serious

personal injury or death.

Trip Summary

You can check the trip summary status for

acceleration, deceleration and speed

during the total distance traveled by your

vehicle for the current trip in the

information display.

WARNING: The system may not

operate properly if your vehicle has a

non-Ford windshield. Do not carry out

windshield repairs in the area around the

sensor.

Checking Trip Summary Status

1. Press the menu button on the steering

wheel to enter the information display

main menu.

2. Select Select screens.

WARNING: In situations where the

vehicle camera has limited detection

capability, this may reduce system

performance. These situations include

but are not limited to direct or low

sunlight, vehicles at night without tail

lights, unconventional vehicle types,

pedestrians with complex backgrounds,

3. Select Eco behaviour.

4. Select the screen on your main screen.

313

Kuga (CTD) Vehicles Built From: 22-06-2021, CG3851en enGBR, Edition date: 202104, First-Printing

Driving Aids

Note: The system is not designed to detect

running pedestrians, partly obscured

animals.

pedestrians, or pedestrians that the

system cannot distinguish from a group.

Failure to take care may result in the loss

of control of your vehicle, serious

personal injury or death.

Note: The system is not designed to detect

vehicles or cyclists that are traveling in a

different direction.

WARNING:The Pre-Collision Assist

system with brake support cannot help

prevent all collisions. Do not rely on this

system to replace your judgment and the

need to maintain correct distance and

speed.

E156130

If your vehicle is rapidly approaching

another stationary vehicle, a vehicle or

cyclist traveling in the same direction as

yours, or a pedestrian within your driving

path, the system is designed to provide

three levels of functionality.

The pre-collision assist system is active

when your vehicle reaches a speed greater

than approximately 5 km/h (3 mph).

Pedestrian detection is active at speeds

up to 80 km/h (50 mph).

Level of Functionality

Description

Alert

When activated, a warning lamp flashes and an audible

warning sounds.

Brake support

The system is designed to help reduce the impact speed by

preparing the brakes for rapid braking. The system does not

automatically apply the brakes. If you press the brake pedal,

the system could apply additional braking up to maximum

braking force, even if you lightly press the brake pedal.

Active braking - vehicles The system is designed to apply the brakes if it detects a

without adaptive cruise crash is imminent. This may help reduce impact or avoid the

control

crash.

The system is active at speeds up to 130 km/h (80 mph).

Active braking - vehicles The system is designed to apply the brakes if it detects a

with adaptive cruise

control

crash is imminent. This may help reduce impact or avoid the

crash.

3. Switch Active braking on or off.

Switching Active Braking On and

Off

Distance Alert(If Equipped)

1. Using the information display controls

on the steering wheel, select Driver

assist..

2. Select Pre-collision Assist.

A warning lamp illuminates if the distance

to the vehicle ahead is small.

314

Kuga (CTD) Vehicles Built From: 22-06-2021, CG3851en enGBR, Edition date: 202104, First-Printing

Driving Aids

Note: The warning lamp does not

4. Select a setting and press the OK

illuminate if cruise control or adaptive cruise

control is active.

button.

Distance Indication (If Equipped)

A graphical indication displays the time

gap to vehicles ahead of you traveling in

the same direction.

Note: The graphic does not display if you

switch on cruise control or adaptive cruise

control.

Setting the Distance Alert Sensitivity

1. Using the information display controls

on the steering wheel, select Driver

assist..

2. Select Pre-collision Assist.

3. Select Alert sensitivity.

Vehicle Speed System Sensit- Distance Indic-

Distance Gap

Time Gap

ivity

ator Color

Gray.

100 km/h

(62 mph)

Normal.

Greater than

Greater than 0.9

seconds.

25 m (82.0 ft) .

Yellow.

Red.

17–25 m

0.6-0.9

(55.8–82.0 ft).

seconds.

Less than 17 m

(55.8 ft).

Less than 0.6

seconds.

Switching Distance Indication On and

Off

1. Using the information display controls

on the steering wheel, select Driver

assist..

2. Select Pre-collision Assist.

3. Switch Distance indication on or off.

Intersection Assist (If Equipped)

E309750

The pre-collision assist system could apply

brakes if you are turning across an

oncoming vehicle's path. Detection of

vehicles driving in an oncoming direction

is active if your vehicle is driving at speeds

up to 30 km/h (18.6 mph).

315

Kuga (CTD) Vehicles Built From: 22-06-2021, CG3851en enGBR, Edition date: 202104, First-Printing

Driving Aids

The camera is mounted behind the interior

Pre-Collision Assist System

Sensors

mirror.

Vehicles without Adaptive Cruise

Control

E243054

E244279

The camera is mounted behind the interior

mirror.

The radar sensor is behind the front grille

below the license plate.

Note: Keep the sensors free from snow, ice

and large accumulations of dirt.

Note: Do not clean the sensors with sharp

objects.

Note: If your vehicle sustains damage

leaving the sensors misaligned, this may

cause inaccurate measurements or false

alerts.

Blocked sensors could affect system

accuracy. A message may appear in the

information display.

Note: If your vehicle sustains damage

leaving the sensors misaligned, this may

cause inaccurate measurements or false

alerts.

Blocked sensors could affect system

accuracy. A message may appear in the

information display.

Vehicles with Adaptive Cruise Control

Pre-CollisionAssistWarningLamp

It illuminates if your vehicle

E350541

rapidly approaches another

vehicle, to warn you of the risk of

a crash with the vehicle in front of you.

It could illuminate red if the distance to the

vehicle ahead is small.

It illuminates when the system is not

available.

E243054

316

Kuga (CTD) Vehicles Built From: 22-06-2021, CG3851en enGBR, Edition date: 202104, First-Printing

Driving Aids

Pre-Collision Assist Information Messages

Message

Action

Pre-collision assist not

available

The system has malfunctioned. Have your vehicle checked

as soon as possible.

Pre-collision assist not

The sensors are dirty. Clean the sensors. If the message

available Sensor blocked continues to appear, have your vehicle checked as soon as

possible.

The following table lists possible causes and actions for when a blocked sensor

message may display.

Cause

Action

The surface of the radar in the radiator grille Clean the radiator grille in front of the radar

is dirty or obstructed.

or remove any obstruction.

The surface of the radar is clean but the

message remains in the display.

Wait for a short period of time. It may take

several minutes for the system to detect

that there is no obstruction.

Heavy rain, spray, snow, or fog is interfering The system is temporarily disabled. The

with the radar signals.

system should reactivate after a short

period of time when the weather conditions

improve.

The radar is misaligned.

Have your vehicle checked as soon as

possible.

The windshield in front of the camera is

dirty or obstructed.

Clean the outside of the windshield in front

of the camera.

The windshield in front of the camera is

clean but the message remains in the

display.

Wait for a short period of time. It may take

several minutes for the camera to detect

that there is no obstruction.

Excessive heat around the camera.

Wait for a short period of time. The

message should clear when the temper-

ature around the camera decreases.

317

Kuga (CTD) Vehicles Built From: 22-06-2021, CG3851en enGBR, Edition date: 202104, First-Printing

Driving Aids

Note: If you turn active braking off, evasive

Evasive Steering Assist(If Equipped)

steering assist also turns off.

If your vehicle is rapidly approaching a

stationary vehicle or a vehicle traveling in

the same direction as yours, the system is

designed to help you steer around the

vehicle.

PRE-COLLISION ASSIST -

VEHICLES WITH: 6.5 INCH

INSTRUMENT CLUSTER

DISPLAY SCREEN/12.3 INCH

INSTRUMENT CLUSTER

DISPLAY SCREEN

The system only activates when all of the

following occur:

•

Active braking and evasive steering

assist are switched on in the

information display.

•

The system detects a vehicle ahead

WARNING: You are responsible for

controlling your vehicle at all times. The

system is designed to be an aid and does

not relieve you of your responsibility to

drive with due care and attention. Failure

to follow this instruction could result in

the loss of control of your vehicle,

personal injury or death.

and starts to apply the brakes.

You significantly turn the steering

wheel in an attempt to steer around

the vehicle.

After you turn the steering wheel in an

attempt to avoid a crash with the vehicle

ahead, the system applies additional

steering torque to help you steer around

the vehicle. After you pass the vehicle, the

system applies steering torque when you

turn the steering wheel to steer back into

the lane. The system deactivates after you

fully pass the vehicle.

WARNING: The system does not

operate during hard acceleration or

steering. Failure to take care may lead

to a crash or personal injury.

WARNING: The system may fail or

operate with reduced function during

cold and severe weather conditions.

Snow, ice, rain, spray and fog can

adversely affect the system. Keep the

front camera and radar free of snow and

ice. Failure to take care may result in the

loss of control of your vehicle, serious

personal injury or death.

Note: The system does not automatically

steer around a vehicle. If you do no turn the

steering wheel, the system does not

activate.

Note: The system does not activate if the

distance to the vehicle ahead is too small

and a crash cannot be avoided.

Switching Evasive Steering Assist On

and Off

WARNING: The system may not

operate properly if your vehicle has a

non-Ford windshield. Do not carry out

windshield repairs in the area around the

sensor.

1. Using the information display controls

on the steering wheel, select Driver

assist..

2. Select Pre-collision Assist.

3. Switch Evasive steering on or off.

Note: Active braking and evasive steering

assist turn on each time you switch the

ignition on.

318

Kuga (CTD) Vehicles Built From: 22-06-2021, CG3851en enGBR, Edition date: 202104, First-Printing

Driving Aids

The pre-collision assist system is active

when your vehicle reaches a speed greater

than approximately 5 km/h (3 mph).

Pedestrian detection is active at speeds

up to 80 km/h (50 mph).

WARNING: In situations where the

vehicle camera has limited detection

capability, this may reduce system

performance. These situations include

but are not limited to direct or low

sunlight, vehicles at night without tail

lights, unconventional vehicle types,

pedestrians with complex backgrounds,

running pedestrians, partly obscured

pedestrians, or pedestrians that the

system cannot distinguish from a group.

Failure to take care may result in the loss

of control of your vehicle, serious

personal injury or death.

Note: The system is not designed to detect

animals.

Note: The system is not designed to detect

vehicles or cyclists that are traveling in a

different direction.

E156130

If your vehicle is rapidly approaching

another stationary vehicle, a vehicle or

cyclist traveling in the same direction as

yours, or a pedestrian within your driving

path, the system is designed to provide

three levels of functionality.

WARNING:The Pre-Collision Assist

system with brake support cannot help

prevent all collisions. Do not rely on this

system to replace your judgment and the

need to maintain correct distance and

speed.

Level of Functionality

Description

Alert

When activated, a warning lamp flashes and an audible

warning sounds.

Brake support

The system is designed to help reduce the impact speed by

preparing the brakes for rapid braking. The system does not

automatically apply the brakes. If you press the brake pedal,

the system could apply additional braking up to maximum

braking force, even if you lightly press the brake pedal.

Active braking - vehicles The system is designed to apply the brakes if it detects a

without adaptive cruise crash is imminent. This may help reduce impact or avoid the

control

crash.

The system is active at speeds up to 130 km/h (80 mph).

Active braking - vehicles The system is designed to apply the brakes if it detects a

with adaptive cruise

control

crash is imminent. This may help reduce impact or avoid the

crash.

319

Kuga (CTD) Vehicles Built From: 22-06-2021, CG3851en enGBR, Edition date: 202104, First-Printing

Driving Aids

Setting the Distance Alert Sensitivity

1. Press the menu button on the steering

wheel to enter the information display

main menu.

Switching Active Braking On and

Off

1. Press the menu button on the steering

wheel to enter the information display

main menu.

2. Select Settings.

3. Select Driver assistance.

4. Select Pre-collision assist.

5. Switch Active braking on or off.

2. Select Settings.

3. Select Driver assistance.

4. Select Pre-collision assist.

5. Select Alert sensitivity.

6. Select a setting and press the OK

button.

Distance Alert (If Equipped)

Distance Indication (If Equipped)

A graphical indication displays the time

gap to vehicles ahead of you traveling in

the same direction.

Note: The graphic does not display if you

switch on cruise control or adaptive cruise

control.

A warning lamp illuminates if the distance

to the vehicle ahead is small.

Note: The warning lamp does not

illuminate if cruise control or adaptive cruise

control is active.

Vehicle Speed System Sensit- Distance Indic-

Distance Gap

Time Gap

ivity

ator Color

Gray.

100 km/h

(62 mph)

Normal.

Greater than

Greater than 0.9

seconds.

25 m (82.0 ft) .

Yellow.

Red.

17–25 m

0.6-0.9

(55.8–82.0 ft).

seconds.

Less than 17 m

(55.8 ft).

Less than 0.6

seconds.

Intersection Assist(If Equipped)

Switching Distance Indication On and

Off

1. Press the menu button on the steering

wheel to enter the information display

main menu.

The pre-collision assist system could apply

brakes if you are turning across an

oncoming vehicle's path. Detection of

vehicles driving in an oncoming direction

is active if your vehicle is driving at speeds

up to 30 km/h (18.6 mph).

2. Select Settings.

3. Select Driver assistance.

4. Select Pre-collision assist.

5. Switch Distance indication on or off.

320

Kuga (CTD) Vehicles Built From: 22-06-2021, CG3851en enGBR, Edition date: 202104, First-Printing

Driving Aids

Vehicles with Adaptive Cruise Control

E243054

E309750

The camera is mounted behind the interior

mirror.

Pre-Collision Assist System

Sensors

Vehicles without Adaptive Cruise

Control

E244279

The radar sensor is behind the front grille

below the license plate.

E243054

The camera is mounted behind the interior

mirror.

Note: Keep the sensors free from snow, ice

and large accumulations of dirt.

Note: Keep the sensors free from snow, ice

Note: Do not clean the sensors with sharp

and large accumulations of dirt.

objects.

Note: Do not clean the sensors with sharp

Note: If your vehicle sustains damage

leaving the sensors misaligned, this may

cause inaccurate measurements or false

alerts.

Blocked sensors could affect system

accuracy. A message may appear in the

information display.

objects.

Note: If your vehicle sustains damage

leaving the sensors misaligned, this may

cause inaccurate measurements or false

alerts.

Blocked sensors could affect system

accuracy. A message may appear in the

information display.

321

Kuga (CTD) Vehicles Built From: 22-06-2021, CG3851en enGBR, Edition date: 202104, First-Printing

Driving Aids

It could illuminate red if the distance to the

Pre-CollisionAssistWarningLamp

vehicle ahead is small.

It illuminates if your vehicle

E350541

rapidly approaches another

It illuminates when the system is not

available.

vehicle, to warn you of the risk of

a crash with the vehicle in front of you.

Pre-Collision Assist Information Messages

Message

Action

Pre-collision assist not

available

The system has malfunctioned. Have your vehicle checked

as soon as possible.

Pre-collision assist not

The sensors are dirty. Clean the sensors. If the message

available Sensor blocked continues to appear, have your vehicle checked as soon as

possible.

The following table lists possible causes and actions for when a blocked sensor

message may display.

Cause

Action

The surface of the radar in the radiator grille Clean the radiator grille in front of the radar

is dirty or obstructed.

or remove any obstruction.

The surface of the radar is clean but the

message remains in the display.

Wait for a short period of time. It may take

several minutes for the system to detect

that there is no obstruction.

Heavy rain, spray, snow, or fog is interfering The system is temporarily disabled. The

with the radar signals.

system should reactivate after a short

period of time when the weather conditions

improve.

The radar is misaligned.

Have your vehicle checked as soon as

possible.

The windshield in front of the camera is

dirty or obstructed.

Clean the outside of the windshield in front

of the camera.

The windshield in front of the camera is

clean but the message remains in the

display.

Wait for a short period of time. It may take

several minutes for the camera to detect

that there is no obstruction.

Excessive heat around the camera.

Wait for a short period of time. The

message should clear when the temper-

ature around the camera decreases.

322

Kuga (CTD) Vehicles Built From: 22-06-2021, CG3851en enGBR, Edition date: 202104, First-Printing

Driving Aids

Note: Active braking and evasive steering

Evasive Steering Assist (If Equipped)

assist turn on each time you switch the

ignition on.

If your vehicle is rapidly approaching a

stationary vehicle or a vehicle traveling in

the same direction as yours, the system is

designed to help you steer around the

vehicle.

Note: If you turn active braking off, evasive

steering assist also turns off.

The system only activates when all of the

following occur:

•

Active braking and evasive steering

assist are switched on in the

information display.

•

The system detects a vehicle ahead

and starts to apply the brakes.

You significantly turn the steering

wheel in an attempt to steer around

the vehicle.

After you turn the steering wheel in an

attempt to avoid a crash with the vehicle

ahead, the system applies additional

steering torque to help you steer around

the vehicle. After you pass the vehicle, the

system applies steering torque when you

turn the steering wheel to steer back into

the lane. The system deactivates after you

fully pass the vehicle.

Note: The system does not automatically

steer around a vehicle. If you do no turn the

steering wheel, the system does not

activate.

Note: The system does not activate if the

distance to the vehicle ahead is too small

and a crash cannot be avoided.

Switching Evasive Steering Assist On

and Off

1. Press the menu button on the steering

wheel to enter the information display

main menu.

2. Select Settings.

3. Select Driver assistance.

4. Select Pre-collision assist.

5. Switch Evasive steering on or off.

323

Kuga (CTD) Vehicles Built From: 22-06-2021, CG3851en enGBR, Edition date: 202104, First-Printing

Driving Aids -> Pre-Collision Assist Vehicles With 4.2 Inch Instrument Cluster Display Screen for Your Ford Kuga SUV 2020

Popular Manuals