Get Features -> HomeLink? Universal Transceiver* Guide for Honda Accord 4 Door 2023

HomeLink® Universal Transceiver^*

1HomeLink ® Universal Transceive r^*

The HomeLink® Universal Transceiver can be programmed to operate up to three

remote controlled devices around your home, such as garage doors, lighting, or

home security systems.

Before programming HomeLink to operate a garage

door opener, confirm that the opener has an external

entrapment protection system, such as an “electronic

eye,” or other safety and reverse stop features. If it

does not, HomeLink may not be able to operate it.

Important Safety Precautions

■

Refer to the safety information that came with your garage door opener to test that

the safety features are functioning properly. If you do not have the safety

information, contact the manufacturer.

NOTE:

Some LED lightbulbs installed in the garage door

opener can interfere with the training and consistent

operation of your HomeLink device. Please consider

use of Low RF interference bulbs in your garage door

opener.

Before programming HomeLink, make sure that people and objects are out of the

way of the garage or gate to prevent potential injury or damage.

When programming a garage door opener, park just outside the garage door’s path.

* Not available on all models

371

uuHomeLink® Universal Transceiver^*uTraining HomeLink

Training HomeLink

If it is necessary to erase a previously entered

Indicator

learned code:

• Press and hold the I and III HomeLink

buttons for about 10 seconds, until the

green indicator blinks. Release the buttons,

and proceed to step 1.

I HomeLink

Button

• If you are training the second or third

button, go directly to step 1.

III HomeLink Button

The instructions on the next page should work for most gate or garage openers, but

may not work for all. For detailed instructions about your specific remote opener,

visit http://www.homelink.com or call (800) 355-3515.

372

uuHomeLink® Universal Transceiver^*uTraining HomeLink

1Training HomeLink

Programming a Button

■

Reprogramming a Button

1. Position the remote transmitter you wish to link 1 to 3 inches (3 - 8 cm) from the

HomeLink® button you want to program.

If you want to retrain a programmed button for a

new device, you do not have to erase all button

memory. You can replace the existing memory code

using this procedure:

Press and hold the desired HomeLink button. Is the HomeLink indicator (LED) slowly

flashing orange?

1. Press and hold the desired HomeLink button until

the HomeLink indicator begins to slowly flash

orange. This should take about 20 seconds.

YES

3a. Hold the button on the remote

transmitter. Does HomeLink indicator

(LED) change from slowly flashing

orange to rapidly flashing green or

continuously on green? The process

should take less than 60 seconds.

3b.

Canadian Garage Door Opener

A. Press and release the HomeLink

button. Press, hold and release the

button on the remote every 2 secs.

Does the HomeLink indicator (LED)

change from slowly flashing orange to

rapidly flashing or continuously on

green? The process should take less

than 60 seconds.

2. Release the HomeLink button and position the

remote transmitter you wish to link 1 - 3 inches

(3 - 8 cm) from the HomeLink button you want to

program, then follow steps 3 - 6 under

“programming a button.”

Erasing Button Memory

4. Press and hold the programmed HomeLink

button for about a second. Does the device

(garage door opener) work?

To erase programming from the buttons, press and hold

the two outside HomeLink buttons until the HomeLink

indicator changes from orange to rapidly flashing green

This should take about 10 seconds. You should erase all

programming before selling the vehicle.

YES

Press and hold the HomeLink button again.

Operating

Training

Complete

To operate, simply press and release the programmed

HomeLink button. Activation will now occur for the

trained device.

HomeLink LED is

continuously on green.

HomeLink indicator rapidly flashes

green.

Questions

6. Press and hold the HomeLink button

5a. The remote has a rolling code. Press the

“learn” button on the remote-controlled

device (e.g. garage door opener).

For questions or comments, visit

again.

www.HomeLink.com , www.youtube.com/

HomeLinkGentex , or by calling the HomeLink Hotline

(North America only) at (800) 355-3515.

The remote-controlled device should

operate.

5b. Within 30 secs, press and hold the

programmed HomeLink button for 2

secs.

Training Complete

HomeLink® is a registered trademark of Gentex

Corporation.

373

Features -> HomeLink? Universal Transceiver* for Your Honda Accord 4 Door 2023

Popular Manuals