Get Maintenance Guide for Hyundai Kona SUV 2020

ENGINE COMPARTMENT

■ Gamma 1.6 T-GDI

1. Engine coolant reservoir/

Engine coolant cap

2. Fuse box

3. Battery

4. Brake fluid reservoir

5. Air cleaner

6. Engine oil dipstick

7. Engine oil filler cap

8. Windshield washer fluid reservoir

9. Engine coolant reservoir

10. Engine coolant cap

■ Nu 2.0 MPI

The actual engine compartment in the

vehicle may differ from the illustration.

7

The actual engine compartment in the vehicle may differ from the illustration.

OOS077001/OOS078071N

7-3

Maintenance

MAINTENANCE SERVICES

You should exercise the utmost care Detailed warranty information is pro- Certain modifications may also be in

to prevent damage to your vehicle vided in your Owner's Handbook & violation of regulations established by

and injury to yourself whenever per- Warranty Information booklet.

the U.S. Department of Transportation

and other federal or state agencies.

forming any maintenance or inspec-

Repairs and adjustments required as

tion procedures.

a result of improper maintenance or

We recommend you have your vehi- a lack of required maintenance are

cle maintained and repaired by an not covered.

authorized HYUNDAI dealer. An

NOTICE

Improper owner maintenance dur-

ing the warranty period may affect

warranty coverage. For details, read

the separate Owner's Handbook &

Warranty Information booklet pro-

vided with the vehicle. If you're

unsure about any service or mainte-

nance procedure, have it done by an

authorized HYUNDAI dealer.

authorized HYUNDAI dealer meets

Owner Maintenance

Precautions

HYUNDAI's high service quality

standards and receives technical

support from HYUNDAI in order to

provide you with a high level of serv-

ice satisfaction.

Inadequate, incomplete or insuffi-

cient servicing may result in opera-

tional problems with your vehicle that

could lead to vehicle damage, an

accident, or personal injury. This

chapter provides instructions only for

the maintenance items that are easy

to perform. Several procedures can

be done only by an authorized

HYUNDAI dealer with special tools.

Your vehicle should not be modified

in any way. Such modifications may

adversely affect the performance,

safety or durability of your vehicle

and may, in addition, violate condi-

tions of the limited warranties cover-

ing the vehicle.

Owner's Responsibility

Maintenance service and record

retention are the owner's responsibil-

ity.

You should retain documents that

show proper maintenance has been

performed on your vehicle in accor-

dance with the scheduled mainte-

nance service charts shown on the

following pages. You need this infor-

mation to establish your compliance

with the servicing and maintenance

requirements of your vehicle war-

ranties.

7-4

OWNER MAINTENANCE

The following lists are vehicle checks

and inspections that should be per-

formed by the owner or an author-

ized HYUNDAI dealer at the frequen-

cies indicated to help ensure safe,

dependable operation of your vehi-

cle.

Any adverse conditions should be

brought to the attention of your deal-

er as soon as possible.

• Block the tires (front and

back) to prevent the vehicle

from moving.

Remove loose clothing or jew-

elry that can become entan-

gled in moving parts.

• If you must run the engine

during maintenance, do so

out doors or in an area with

plenty of ventilation.

• Keep flames, sparks, or smok-

ing materials away from the

battery and fuel-related parts.

WARNING

Performing maintenance work

on a vehicle can be dangerous.

If you lack sufficient knowledge

and experience or the proper

tools and equipment to do the

work, have it done by an author-

ized HYUNDAI dealer.

ALWAYS follow these precau-

tions for performing mainte-

nance work:

• Park your vehicle on level

ground, move the shift lever

into the P (Park, for automatic

transmission vehicle) posi-

tion, place the ignition switch

in the LOCK/OFF position.

These Owner Maintenance vehicle

checks are generally not covered by

warranties and you may be charged

for labor, parts and lubricants used.

7

7-5

Maintenance

• Check the parking brake.

While operating your vehicle:

Owner Maintenance Schedule

• Check for fluid leaks under your

vehicle (water dripping from the air

conditioning system during or after

use is normal).

• Note any changes in the sound of

the exhaust or any smell of

exhaust fumes in the vehicle.

• Check for vibrations in the steering

wheel. Notice if there is any

increased steering effort or loose-

ness in the steering wheel, or

change in its straight-ahead posi-

tion.

• Notice if your vehicle constantly

turns slightly or "pulls" to one side

when traveling on smooth, level

road.

• When stopping, listen and check

for unusual sounds, pulling to one

side, increased brake pedal travel

or "hard-to-push" brake pedal.

When you stop for fuel:

• Check the engine oil level.

• Check the coolant level in the

engine coolant reservoir.

• Check the windshield washer fluid

level.

At least monthly:

• Check coolant level in the engine

coolant reservoir.

• Check the operation of all exterior

lights, including the brake lights,

turn signals and hazard warning

flashers.

• Check the inflation pressures of all

tires including the spare for tires

that are worn, show uneven wear,

or are damaged.

• Check the for low or under-inflated

tires.

WARNING

Be careful when checking your

engine coolant level when the

engine is hot.This may result in

coolant being blown out of the

opening and cause serious

burns and other injuries.

• Check for loose wheel lug nuts.

• If any slipping or changes in the

operation of your transmission

occurs, check the transmission

fluid level.

• Check the automatic transmission/

dual clutch transmission P (Park)

function.

7-6

SCHEDULED MAINTENANCE

SERVICES

Follow Normal Maintenance Schedule

if the vehicle is usually operated where

none of the following conditions apply.

If any of the following conditions apply,

you must follow the Maintenance

Under Severe Usage Conditions.

• Repeated short distance driving.

• Driving in dusty conditions or

sandy areas.

• Extensive use of brakes.

• Driving in areas where salt or other

corrosive materials are used.

At least twice a year:

At least once a year:

• Clean body and door drain holes.

• Lubricate door hinges and hood

hinges.

• Lubricate door and hood locks and

latches.

• Lubricate door rubber weather

strips.

• Lubricate door checker.

• Check the air conditioning system.

• Inspect and lubricate automatic

transmission linkage and controls.

(i.e., every Spring and Autumn)

• Check radiator, heater and air con-

ditioning hoses for leaks or dam-

age.

• Check windshield washer spray

and wiper operation. Clean wiper

blades with a clean cloth damp-

ened with washer a fluid.

• Check headlamp alignment.

• Check muffler, exhaust pipes,

shields and clamps.

• Check the seat belts for wear and

function.

• Clean the battery and terminals.

• Check the brake fluid level.

• Driving on rough or muddy roads.

• Driving in mountainous areas.

• Extended periods of idling or low

speed operation.

• Driving for a prolonged period in

cold temperatures and/or extreme-

ly humid climates.

7

• More than 50% driving in heavy

city traffic during hot weather

above 90°F (32°C).

For additional information or assis-

tance see your authorized HYUNDAI

dealer.

7-7

Maintenance

Normal Maintenance Schedule (Nu 2.0 MPI)

MAINTENANCE

INTERVALS

Months

12 24 36 48 60 72 84 96 108 120 132 144 156 168 180

Miles×1,000 7.5 15 22.5 30 37.5 45 52.5 60 67.5 75 82.5 90 97.5 105 112.5

MAINTENANCE

ITEM

Km×1,000

12 24 36 48 60 72 84 96 108 120 132 144 156 168 180

At first, inspect at 60,000 miles or 72 months.

Thereafter, inspect every 15,000 miles or 24 months

Drive belts *¹

Engine oil and engine oil filter

Fuel additives *²

Air cleaner filter

Spark plugs

R

I

R

I

R

I

R

I

R

I

R

I

Add fuel additives every 7,500 miles or 12 months

R

I

R

I

R

Replace every 97,500 miles

Rotate tires every 7,500 miles

Rotate tires

Climate control air filter

(for evaporator and blower unit)

Replace every 15,000 miles or 12 months

At first, replace at 120,000 miles or 10 years :

Thereafter, replace every 30,000 miles or 24 months

Engine coolant

Vacuum hose

I

Battery condition

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

*¹: The drive belt should be replaced when cracks occur or tension is reduced excessively.

*²: If TOP TIER Detergent Gasoline is not available, one bottle of additive is recommended. Additives are available from your

authorized HYUNDAI dealer along with information on how to use them. Do not mix other additives.

7-8

Normal Maintenance Schedule (Nu 2.0 MPI) (CONT)

MAINTENANCE

INTERVALS

Months

Miles×1,000 7.5 15 22.5 30 37.5 45 52.5 60 67.5 75 82.5 90 97.5 105 112.5

Km×1,000 12 24 36 48 60 72 84 96 108 120 132 144 156 168 180

12 24 36 48 60 72 84 96 108 120 132 144 156 168 180

MAINTENANCE

ITEM

Brake lines, hoses and connections

Disc brakes and pads

I

Steering gear rack, linkage and boots/

lower arm ball joint, upper arm ball joint

I

Driveshaft and boots

I

Suspension mounting bolts

Air conditioner refrigerant

Air conditioner compressor

Propeller shaft (AWD)

Exhaust pipe and muffler

Automatic transaxle fluid

Rear differential oil (AWD) *³

Transfer case oil (AWD)*³

I

No check, No service required

7

I

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

*³: Transfer case oil and rear differential oil should be changed anytime they have been submerged in water.

7-9

Maintenance

Normal Maintenance Schedule (Nu 2.0 MPI) (CONT)

MAINTENANCE

INTERVALS

Months

Miles×1,000 7.5 15 22.5 30 37.5 45 52.5 60 67.5 75 82.5 90 97.5 105 112.5

Km×1,000 12 24 36 48 60 72 84 96 108 120 132 144 156 168 180

12 24 36 48 60 72 84 96 108 120 132 144 156 168 180

MAINTENANCE

ITEM

Vapor hose, fuel filler cap and fuel tank

Fuel tank air filter *⁴

Fuel filter *⁴

I

Fuel lines, hoses and connections

Parking brake

I

Brake fluid

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

*⁴: Fuel filter & Fuel tank air filter are considered to be maintenance free but periodic inspection is recommended for this mainte-

nance schedule depends on fuel quality. If there are some important safety matters like fuel flow restriction, surging, loss of

power, hard starting problem, etc. replace the fuel filter immediately regardless of maintenance schedule and consult an

authorized HYUNDAI dealer for details.

7-10

Maintenance Under Severe Usage Conditions (Nu 2.0 MPI)

The following items must be serviced more frequently on cars normally used under severe driving conditions. Refer

to the chart below for the appropriate maintenance intervals.

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

MAINTENANCE

OPERATION

DRIVING

CONDITION

MAINTENANCE ITEM

Engine oil and filter

MAINTENANCE INTERVALS

Every 3,750 miles or 6 months

More frequently

A, B, C, D, E, F,

G, H, I, J, K

R

I

Air cleaner filter

C, E

Spark plugs

More frequently

A, B, H, I, K

A, C, D, E, F,

G, H, I, J

Automatic transmission fluid

Front brake disc/pads, calipers

Rear brake shoes or disc/pads

Every 60,000 miles

More frequently

C, D, G, H

C, D, G, F

I

More frequently

7

7-11

Maintenance

MAINTENANCE

OPERATION

DRIVING

CONDITION

MAINTENANCE ITEM

MAINTENANCE INTERVALS

More frequently

Parking brake

I

C, D, G, H

C, D, E, F, G, H, I

C, D, E, F, G, H, I, J

C, E

Steering gear box, linkage & boots/

lower arm ball joint, upper arm ball joint

More frequently

Drive shafts and boots

I

More frequently

Climate control air filter

(for evaporator and blower unit)

R

I

More frequently

Propeller shaft (AWD)

Transfer case oil (AWD)

Rear differential oil (AWD)

More frequently

C, D, E, F, G, H, I, J

C, D, E, G, H, I, J

R

Every 75,000 miles (120,000 km)

Severe Driving Conditions

A-Repeatedly driving short distances of less than 5 miles

(8 km) in normal temperature or less than 10 miles (16 km)

in freezing temperature

B-Extensive engine idling or low speed driving for long dis-

tances

C-Driving on rough, dusty, muddy, unpaved, graveled or salt-

spread roads

D-Driving in areas using salt or other corrosive materials or in

very cold weather

E-Driving in sandy areas

F -Driving in heavy traffic area over 90°F (32°C)

G-Driving on uphill, downhill, or mountain road

H-Towing a Trailer, or using a camper, or roof rack

I -Driving as a patrol car, taxi, other commercial use or vehicle

towing

J -Driving over 106 mph (170 km/h)

K-Frequently driving in stop-and-go conditions

7-12

Normal Maintenance Schedule (Gamma 1.6 T-GDI)

MAINTENANCE

INTERVALS

Months

12 24 36 48 60 72 84 96 108 120 132 144 156 168 180

12 18 24 30 36 42 48 54 60 66 72 78 84 90

Miles×1,000

Km×1,000

6

MAINTENANCE

10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

ITEM

At first, inspect at 60,000 miles or 72 months.

Thereafter, inspect every 12,000 miles or 24 months

Drive belts *¹

Engine oil and engine oil filter

Fuel additives *²

Air cleaner filter

Spark plugs

R

I

R

I

R

I

R

I

R

I

R

I

Add fuel additives every 6,000 miles or 12 months

R

I

R

I

R

Replace every 42,000 miles

Valve clearance *³

Inspect every 60,000 miles or 72 months

Rotate tires every 6,000 miles

Rotate tires

Climate control air filter

(for evaporate and blower unit)

Replace every 12,000 miles or 12 months.

At first, replace at 120,000 miles or 10 years :

Thereafter, replace every 30,000 miles or 24 months

Engine coolant

7

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

*¹: The drive belt should be replaced when cracks occur or tension is reduced excessively.

*²: If TOP TIER Detergent Gasoline is not available, one bottle of additive is recommended. Additives are available from your

authorized HYUNDAI dealer along with information on how to use them. Do not mix other additives.

*³: Inspect for excessive valve noise and/or engine vibration and adjust if necessary. Have an authorized HYUNDAI dealer per-

form the operation.

7-13

Maintenance

Normal Maintenance Schedule (Gamma 1.6 T-GDI) (CONT)

MAINTENANCE

INTERVALS

Months

12 24 36 48 60 72 84 96 108 120 132 144 156 168 180

12 18 24 30 36 42 48 54 60 66 72 78 84 90

10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

Miles×1,000

Km×1,000

6

MAINTENANCE

ITEM

Intercooler, in/out hose, air intake hose

Vacuum hose

I

Battery condition

Brake lines, hoses and connections

Disc brakes and pads

Steering gear rack, linkage and boots/

lower arm ball joint, upper arm ball joint

I

Driveshaft and boots

I

Suspension mounting bolts

Air conditioner refrigerant

Air conditioner compressor

Propeller shaft (AWD)

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

7-14

Normal Maintenance Schedule (Gamma 1.6 T-GDI) (CONT)

MAINTENANCE

INTERVALS

Months

12 24 36 48 60 72 84 96 108 120 132 144 156 168 180

12 18 24 30 36 42 48 54 60 66 72 78 84 90

10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

Miles×1,000

Km×1,000

6

MAINTENANCE

ITEM

Exhaust pipe and muffler

I

Dual clutch transmission fluid

Rear differential oil (AWD) *⁴

Transfer case oil (AWD)*⁴

Vapor hose, fuel filler cap and fuel tank

Fuel tank air filter *⁵

Fuel filter *⁵

I

Fuel lines, hoses and connections

Parking brake

I

Brake fluid

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

*⁴: Transfer case oil and rear differential oil should be changed anytime they have been submerged in water.

7

*⁵: Fuel filter & Fuel tank air filter are considered to be maintenance free but periodic inspection is recommended for this mainte-

nance schedule depends on fuel quality. If there are some important safety matters like fuel flow restriction, surging, loss of

power, hard starting problem, etc. replace the fuel filter immediately regardless of maintenance schedule and consult an

authorized HYUNDAI dealer for details.

7-15

Maintenance

Maintenance Under Severe Usage Conditions (Gamma 1.6 T-GDI)

The following items must be serviced more frequently on cars normally used under severe driving conditions. Refer

to the chart below for the appropriate maintenance intervals.

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

MAINTENANCE

OPERATION

DRIVING

CONDITION

MAINTENANCE ITEM

Engine oil and filter

MAINTENANCE INTERVALS

Every 3,000 miles or 6 months

More frequently

A, B, C, D, E, F,

G, H, I, J, K

R

I

Air cleaner filter

C, E

Spark plugs

More frequently

A, B, H, I, K

C, D, E, F,

G, H, I, J

Dual clutch transmission fluid

Front brake disc/pads, calipers

Rear brake shoes or disc/pads

Every 72,000 miles

More frequently

C, D, G, H

C, D, G, F

I

More frequently

7-16

MAINTENANCE

OPERATION

DRIVING

CONDITION

MAINTENANCE ITEM

Parking brake

MAINTENANCE INTERVALS

More frequently

I

C, D, G, H

C, D, E, F, G, H, I

C, D, E, F, G, H, I, J

C, E

Steering gear box, linkage & boots/

lower arm ball joint, upper arm ball joint

More frequently

Drive shafts and boots

I

More frequently

Climate control air filter

(for evaporator and blower unit)

R

I

More frequently

Propeller shaft (AWD)

More frequently

C, D, E, F, G, H, I, J

C, D, E, G, H, I, J

Transfer case oil (AWD)

R

Every 75,000 miles (120,000 km)

Rear differential oil (AWD)

Severe Driving Conditions

A-Repeatedly driving short distances of less than 5 miles

(8 km) in normal temperature or less than 10 miles (16 km)

in freezing temperature

B-Extensive engine idling or low speed driving for long dis-

tances

C-Driving on rough, dusty, muddy, unpaved, graveled or salt-

spread roads

D-Driving in areas using salt or other corrosive materials or in

very cold weather

E-Driving in sandy areas

7

F -Driving in heavy traffic area over 90°F (32°C)

G-Driving on uphill, downhill, or mountain road

H-Towing a Trailer, or using a camper, or roof rack

I -Driving as a patrol car, taxi, other commercial use or vehicle

towing

J -Driving over 106 mph (170 km/h)

K-Frequently driving in stop-and-go conditions

7-17

Maintenance

EXPLANATION OF SCHEDULED MAINTENANCE ITEMS

Engine Oil and Filter

Fuel Lines, Fuel Hoses and

Connections

Vacuum Crankcase Ventilation

Hoses (if equipped)

The engine oil and filter should be

changed at the intervals specified in

the maintenance schedule. If the

vehicle is being driven in severe con-

ditions, more frequent oil and filter

changes are required.

Check the fuel lines, fuel hoses and Inspect the surface of hoses for evi-

connections for leakage and dam- dence of heat and/or mechanical

age. Have an authorized HYUNDAI damage. Hard and brittle rubber,

dealer replace any damaged or leak- cracking, tears, cuts, abrasions, and

ing parts immediately.

excessive swelling indicate deterio-

ration. Particular attention should be

paid to examine those hose surfaces

nearest to high heat sources, such

as the exhaust manifold.

Inspect the hose routing to ensure

that the hoses do not come in con-

tact with any heat source, sharp

edges or moving component which

might cause heat damage or

mechanical wear. Inspect all hose

connections, such as clamps and

couplings, to make sure they are

secure, and that no leaks are pres-

ent. Hoses should be replaced

immediately if there is any evidence

of deterioration or damage.

Drive Belts

Vapor Hose and Fuel Filler

Cap

Inspect all drive belts for evidence of

cuts, cracks, excessive wear or oil

saturation and replace if necessary.

Drive belts should be checked peri-

odically for proper tension and

adjusted as necessary.

The vapor hose and fuel filler cap

should be inspected at those inter-

vals specified in the maintenance

schedule. Make sure a new vapor

hose or fuel filler cap is correctly

replaced.

Fuel Filter

A clogged-up fuel filter may limit the

vehicle driving speed, damage the

emission system, and cause the

hard starting. When a considerable

amount of foreign substances are

accumulated in the fuel tank, the fuel

filter should be replaced.

Upon installing a new fuel filter, oper-

ate the engine for several minutes,

and check the connections for any

leakages. Fuel filters should be

installed by an authorized HYUNDAI

dealer.

7-18

Air Cleaner Filter

Automatic Transmission Fluid

(if equipped)

CAUTION

A genuine HYUNDAI air cleaner filter

is recommended when the filter is

replaced.

Automatic transmission fluid should

not be checked under normal usage

conditions. But in severe conditions,

the fluid should be changed at an

authorized HYUNDAI dealer in

accordance to the scheduled mainte-

nance at the beginning of this chap-

ter.

The use of a non-specified fluid

could result in transmission

malfunction and failure. Use

only the specified automatic

transmission fluid (refer to

"Recommended Lubricants and

Capacities" in chapter 8).

Spark Plugs

Make sure to install new spark plugs

of the correct heat range.

Cooling System

Dual Clutch Transmission

Fluid (if equipped)

Inspect the dual clutch transmission

fluid according to the maintenance

schedule.

NOTICE

Check cooling system components,

such as radiator, coolant reservoir,

hoses and connections for leakage

and damage. Replace any damaged As the vehicle is driven, the auto-

parts.

Automatic transmission fluid

color is red when new.

matic transmission fluid will begin

to look darker. This is a normal

condition and you should not

judge the need to replace the fluid

Engine Coolant

The coolant should be changed at based upon the changed color.

the intervals specified in the mainte-

nance schedule.

7

7-19

Maintenance

Brake Hoses and Lines

Exhaust Pipe and Muffler

Drive Shafts and Boots

Visually check for proper installation, Visually inspect the exhaust pipes, Check the drive shafts, boots and

chafing, cracks, deterioration and muffler and hangers for cracks, dete- clamps for cracks, deterioration, or

any leakage. Replace any deteriorat- rioration, or damage. Start the engine damage. Replace any damaged

ed or damaged parts immediately.

and listen carefully for any exhaust parts and, if necessary, repack the

gas leakage. Tighten connections or grease.

replace parts as necessary.

Brake Fluid

Check the brake fluid level in the

brake fluid reservoir.The level should

Air Conditioning Refrigerant

Suspension Mounting Bolts

Check the air conditioning lines and

be between the MIN and the MAX Check the suspension connections connections for leakage and dam-

marks on the side of the reservoir. for looseness or damage. Retighten age.

Use only hydraulic brake fluid con- to the specified torque.

forming to DOT 3 or DOT 4 specifi-

cation.

Steering Gear Box, Linkage &

Boots/Lower Arm Ball Joint

Parking Brake

With the vehicle stopped and the

Inspect the parking brake system

including the parking brake pedal

and cables.

engine off, check for excessive free-

play in the steering wheel. Check the

linkage for bends or damage. Check

the dust boots and ball joints for

deterioration, cracks, or damage.

Brake Discs, Pads, Calipers

and Rotors

Replace any damaged parts.

Check the pads for excessive wear,

discs for run out and wear, and

calipers for fluid leakage.

7-20

ENGINE OIL

Checking the Engine Oil Level

■ 1.6 T-GDI

1. Follow all of the oil manufacturer's

precautions.

2. Be sure the vehicle is on the level

ground in P (Park) with the park-

ing brake set. If possible, block the

wheels.

3. Turn the engine on and allow the

engine to reach normal operating

temperature.

4. Turn the engine off and wait about

five minutes for the oil to return to

the oil pan.

5. Pull the dipstick out, wipe it clean,

and re-insert it fully.

OPDE076067

OOS077005

■ 2.0 MPI

6. Pull the dipstick out again and

check the level. The level should

be between F and L.

7

OOS077005N

7. If it is near or at L, add enough oil

to bring the level to F.

Use only the specified engine oil.

(refer to "Recommended Lubricants

and Capacities" in chapter 8).

7-21

Maintenance

Checking the Engine Oil and

Filter

NOTICE

WARNING

To prevent damage to your

engine:

• Do not overfill with engine oil.

Add oil in small quantities and

recheck level to ensure engine

is not overfilled.

• Do not spill engine oil when

adding or changing engine oil.

Use a funnel to help prevent oil

from being spilled on engine

components. Wipe off spilled oil

immediately.

CALIFORNIA PROPOSITION 65

WARNING

Engine oil contains chemicals

known to the State of California

to cause cancer, birth defects

and reproductive harm. Used

engine oil may cause irritation

or cancer of the skin if left in

contact with the skin for pro-

longed periods of time. Always

protect your skin by washing

your hands thoroughly with

soap and warm water as soon

as possible after handling used

oil.

Have engine oil and filter changed by

an authorized HYUNDAI dealer

according to the Maintenance

Schedule at the beginning of this

chapter.

7-22

ENGINE COOLANT

The high-pressure cooling system

has a reservoir filled with year-round

antifreeze coolant. The reservoir is

filled at the factory.

The coolant level should be filled

between the F and the L marks on

the side of the coolant reservoir

when the engine is cool.

Checking the Engine Coolant

Level

■ 1.6 T-GDI

Check the antifreeze protection and

coolant level at least once a year, at

the beginning of the winter season

and before traveling to a colder cli-

mate.

If the coolant level is low, add enough

distilled (deionized) water to bring the

level to the F mark, but do not overfill.

If frequent additions are required, see

an authorized HYUNDAI dealer for a

cooling system inspection.

Recommended engine coolant

• When adding coolant, use only dis-

tilled (deionized) water for your

vehicle and never mix hard water in

the coolant filled at the factory.

OOS077007

■ 2.0 MPI

• An improper coolant mixture can

result in severe malfunction or

engine damage.

7

• The engine in your vehicle has alu-

minum engine parts and must be

protected by an ethylene-glycol

with phosphate based coolant to

prevent corrosion and freezing.

• Do not use alcohol or methanol

coolant or mix them with the spec-

ified coolant.

OOS077076N

Check the condition and connections

of all cooling system hoses and

heater hoses. Replace any swollen

or deteriorated hoses.

7-23

Maintenance

• Do not use a solution that contains

more than 60% antifreeze or less

than 35% antifreeze, which would

reduce the effectiveness of the

solution.

WARNING

For 1.6 T-GDI

Make sure the coolant cap is

properly closed after refilling

coolant. Otherwise the engine

could be overheated while driv-

ing.

For mixing percentage, refer to the

following table:

Mixture Percentage

■ Engine room front view

Ambient

(volume)

OPDE076071

Temperature

Antifreeze

Water

65

2. Make sure that the tiny pro-

trusions inside the coolant

cap is securely interlocked.

5°F (-15°C)

-13°F (-25°C)

-31°F (-35°C)

-49°F (-45°C)

35

40

50

60

50

40

i

Information

OTL075062

If in doubt about the mix ratio, a 50%

water and 50% antifreeze mix is the

easiest to mix together as it will be the

same quantity of each. It is suitable to

use for most temperature ranges of

- 31°F and higher.

1. Check if the coolant cap label

is straight In front.

7-24

■ 1.6 T-GDI

WARNING

Never remove the

engine coolant reser-

The electric motor for

the cooling fan may

voir tank/radiator cap

continue to operate

or the drain plug

while the engine and

or start up when the

engine is not running

radiator are hot. Hot coolant

and steam may blow out under

pressure, causing serious

injury.

and can cause serious injury.

Keep hands, clothing and tools

away from the rotating fan

blades of the cooling fan.

OOS077009

Turn the engine off and wait

until the engine cools down.

Use extreme care when remov-

ing the engine coolant reservoir

tank/radiator cap. Wrap a thick

towel around it, and turn it

counterclockwise slowly to the

first stop. Step back while the

pressure is released from the

cooling system. When you are

sure all the pressure has been

released, press down on the

cap, using a thick towel, and

continue turning counterclock-

wise to remove it.

■ 2.0 MPI

The electric motor for the cooling fan

is controlled by engine coolant tem-

perature, refrigerant pressure and

vehicle speed. As the engine coolant

temperature decreases, the electric

motor will automatically shut off. This

is a normal condition. If your vehicle

is equipped with GDI, the electric

motor for the cooling fan may begin

to operate at any time and continue

to operate until you disconnect the

negative battery cable.

7

OOS077077N

7-25

Maintenance

Changing Engine Coolant

NOTICE

Have coolant changed by an author-

ized HYUNDAI dealer according to

the Maintenance Schedule at the

beginning of this chapter.

To prevent damage to engine

parts, put a thick towel around the

radiator cap before refilling the

coolant to prevent the coolant

from overflowing into engine

parts, such as the alternator.

WARNING

Do not use engine coolant or

antifreeze in the washer fluid

reservoir.

Engine coolant can severely

obscure visibility when sprayed

on the windshield and may

cause loss of vehicle control

resulting in an accident.

Engine coolant may also cause

damage to paint and body trim.

7-26

BRAKE FLUID

Checking the Brake Fluid

Level

If the level is low, add the specified

brake fluid to the MAX level.The level

will fall with accumulated mileage.

This is a normal condition associated

with the wear of the brake linings. If

the fluid level is excessively low, have

the brake system checked by an

authorized HYUNDAI dealer.

NOTICE

• Do not allow brake fluid to con-

tact the vehicle’s body paint, as

paint damage will result.

• Brake fluid, which has been

exposed to open air for an

extended time should NEVER be

used as its quality cannot be

guaranteed. It should be dis-

posed of properly.

WARNING

• Do not use the wrong kind of

brake fluid. A few drops of min-

eral based oil, such as engine

oil, in your brake system can

damage brake system parts.

If the brake system requires fre-

quent additions of fluid this

could indicate a leak in the

brake system. Have the vehicle

inspected by an authorized

HYUNDAI dealer.

OOS077011

Check the fluid level in the reservoir

periodically. The fluid level should be

between MAX and MIN marks on the

side of the reservoir.

Before removing the reservoir cap

and adding brake fluid, clean the

area around the reservoir cap thor-

oughly to prevent brake fluid contam-

ination.

i

Information

Use only the specified brake fluid

(refer to "Recommended Lubricants

and Capacities" in chapter 8).

WARNING

7

Do not allow brake fluid to come

in contact with your eyes. If

brake fluid comes in contact

with your eyes, flush your eyes

with clean water for at least 15

minutes and get immediate

medical attention.

7-27

Maintenance

WASHER FLUID

Checking the Washer Fluid

Level

PARKING BRAKE

Checking the Parking Brake

WARNING

To prevent serious injury or

death, take the following safety

precautions when using washer

fluid:

• Do not use engine coolant or

antifreeze in the washer fluid

reservoir.

Engine coolant can severely

obscure visibility when sprayed

on the windshield and may

cause loss of vehicle control

resulting in an accident or dam-

age to paint and body trim.

• Do not allow sparks or flames

to contact the washer fluid or

the washer fluid reservoir.

Washer fluid may contain alco-

hol and can be flammable.

• Do not drink washer fluid and

avoid contact with skin.

Washer fluid is harmful to

humans and animals.

• Keep washer fluid away from

children and animals.

OOS057010

OOS077012

Check the stroke of the parking

brake by counting the number of

"clicks" heard while fully applying it

from the released position. Also, the

parking brake alone should securely

hold the vehicle on a fairly steep

grade. If the stroke is more or less

than specified, have the parking

brake adjusted by an authorized

HYUNDAI dealer.

Check the fluid level in the washer

fluid reservoir and add fluid if neces-

sary. Plain water may be used if

washer fluid is not available.

However, use washer solvent with

antifreeze characteristics in cold cli-

mates to prevent freezing.

Stroke : 5~7 clicks at a force of 44

lbs (20 kg, 196 N)

7-28

AIR CLEANER

Filter Replacement

OOS077015

OOS077016

1. Loosen the air cleaner cover 3. Replace the air cleaner filter.

OOS077013

attaching clips and open the cover.

4. Lock the cover with the cover

The air cleaner filter can be cleaned

for inspection using compressed air.

Do not attempt to wash or to rinse it,

as water will damage the filter.

2. Wipe the inside of the air cleaner.

attaching clips.

5. Check that the cover is firmly

installed.

If soiled, the air cleaner filter must be

replaced.

7

7-29

Maintenance

CLIMATE CONTROL AIR FILTER

Filter Inspection

i

Information

The climate control air filter should

be replaced according to the

Maintenance Schedule. If the vehicle

is operated in severely air-polluted

cities or on dusty rough roads for a

long period, it should be inspected

more frequently and replaced earlier.

When you replace the climate control

air filter, replace it performing the fol-

lowing procedure, and be careful to

avoid damaging other components.

If the vehicle is operated in extremely

dusty or sandy areas, replace the ele-

ment more often than the usual rec-

ommended intervals (refer to

"Maintenance Under Severe Usage

Conditions" in this chapter).

NOTICE

• Do not drive with the air cleaner

filter removed. This will result in

excessive engine wear.

• When removing the air cleaner

filter, be careful that dust or dirt

does not enter the air intake, or

damage may result.

OOS077018

1. With the glove box open, remove

the stoppers on both sides to allow

the glove box to hang freely on the

hinges.

• Use HYUNDAI genuine parts.

Use of non-genuine parts could

damage the air flow sensor.

7-30

OOS077019

OPD076026

OOS077017

2. Remove the support rod (1).

3. Remove the climate control air fil- 4. Replace the climate control air fil-

ter case while pressing the lock on

the right side of the cover.

ter.

5. Reassemble in the reverse order

of disassembly.

NOTICE

Install a new climate control air fil-

ter in the correct direction with the

7

arrow symbol ( ) facing down-

↓

wards, otherwise, it may be noisy

and the effectiveness of the filter

may be reduced.

7-31

Maintenance

WIPER BLADES

Front windshield wiper blade

replacement

Blade Inspection

Blade Replacement

Contamination of either the windshield When the wipers no longer clean

or the wiper blades with foreign matter adequately, the blades may be worn

can reduce the effectiveness of the or cracked, and require replacement.

windshield

wiper

functionality.

Common sources of contamination

are insects, tree sap, and hot wax

treatments used by some commercial

car washes. If the blades are not wip-

ing properly, clean both the window

and the blades with a clean cloth

dampened with washer fluid.

NOTICE

To prevent damage to the wiper

arms or other components, do not

attempt to move the wipers manu-

ally.

NOTICE

OLMB073020

The use of a non-specified wiper

blade could result in wiper mal-

function and failure.

■

Type A

To prevent damage to the wiper

blades, arms or other compo-

nents, do not:

• Use gasoline, kerosene, paint

thinner, or other solvents on or

near them.

• Attempt to move the wipers

manually.

• Use non-specified wiper blades.

1. Put the front windshield wipers

into the service position.

2. Raise the wiper arm and slightly

rotate the wiper blade assembly to

expose the plastic locking clip.

NOTICE

• In order to prevent damage to

the hood and the wiper arms, the

wiper arms should only be lifted

when in the top wiping position.

• Always return the wiper arms to

the windshield before driving.

NOTICE

Do not allow the wiper arm to fall

against the windshield, since it

may chip or crack the windshield.

i

Information

Commercial hot waxes applied by auto-

matic car washes have been known to

make the windshield difficult to clean.

7-32

OLMB073099

OLMB073098

OLMB073021

■

Type B

1. Raise the wiper arm.

NOTICE

Do not allow the wiper arm to fall

against the windshield, since it

may chip or crack the windshield.

7

OLMB073022

OLMB073100

3. Press the clip (1) and slide the

blade assembly downward (2).

4. Lift it off the arm.

2. Lift up the wiper blade clip (1).

Then pull down the blade assem-

bly (2) and remove it.

3. Install the new blade assembly in

the reverse order of removal.

4. Return the wiper arm on the wind-

5. Install the blade assembly in the

reverse order of removal.

6. Return the wiper arm on the wind-

shield.

7-33

Maintenance

Rear window wiper blade

replacement

OTL075051

2. Install the new blade assembly by

inserting the center part into the

slot in the wiper arm until it clicks

into place.

3. Make sure the blade assembly is

installed firmly by trying to pull it

slightly.

OTL075050

1. Raise the wiper arm and pull out

the wiper blade assembly.

To prevent damage to the wiper arms

or other components, have the wiper

blades replaced by an authorized

HYUNDAI dealer.

7-34

BATTERY

Batteries contain sulfu-

ric acid which is highly

corrosive. Do not allow

acid to contact your

eyes, skin or clothing.

• NEVER attempt to recharge

the battery when the vehicle’s

battery cables are connected

to the battery.

• The electrical ignition system

works with high voltage.

NEVER touch these compo-

nents with the engine running

or when the ignition switch is

in the ON position.

WARNING

To prevent SERIOUS INJURY or

DEATH to you or bystanders,

always follow these precautions

when working near or handling

the battery:

If acid gets into your eyes, flush

your eyes with clean water for at

least 15 minutes and get imme-

diate medical attention. If acid

gets on your skin, thoroughly

wash the area. If you feel pain or

a burning sensation, get med-

ical attention immediately.

Always read and follow

instructions

carefully

when handling a battery.

Wear eye protection

designed to protect the

eyes from acid splashes.

• When lifting a plastic-cased

battery, excessive pressure

on the case may cause battery

acid to leak. Lift with a battery

carrier or with your hands on

opposite corners.

• Do not attempt to jump start

your vehicle if your battery is

frozen.

Keep all flames, sparks,

or smoking materials

away from the battery.

Hydrogen is always pres-

ent in battery cells, is

highly combustible, and

may explode if ignited.

7

Keep batteries out of

reach of children.

7-35

Maintenance

For Best Battery Service

Battery Recharging

WARNING

CALIFORNIA PROPOSITION 65

WARNING

Always follow these instruc-

tions when recharging your

vehicle's battery to avoid the

risk of SERIOUS INJURY or

DEATH from explosions or acid

burns:

• Before performing mainte-

nance or recharging the bat-

tery, turn off all accessories

and place the ignition switch

to the LOCK/OFF position.

• Keep all flames, sparks, or

smoking materials away from

the battery.

• Always work outdoors or in an

area with plenty of ventilation.

Battery posts, terminals, and

related accessories contain

lead and lead compounds,

chemicals known to the State of

California to cause cancer, birth

defects and reproductive harm.

Batteries also contain other

chemicals known to the State of

California to cause cancer.

Wash hands after handling.

OOS077020

• Keep the battery securely mount-

ed.

• Keep the battery top clean and dry.

• Keep the terminals and connec-

tions clean, tight, and coated with

petroleum jelly or terminal grease.

• Rinse any spilled acid from the bat-

tery immediately with a solution of

water and baking soda.

NOTICE

• When you do not use the vehicle

for a long time in a low tempera-

ture area, disconnect the battery

and keep it indoors.

• Always charge the battery fully

to prevent battery case damage

in low temperature areas.

• Wear eye protection when

checking the battery during

charging.

• The battery must be removed

from the vehicle and placed in

a well ventilated area.

7-36

By jump starting

Reset Features

• Watch the battery during

charging, and stop or reduce

the charging rate if the battery

cells begin boiling violently.

• The negative battery cable

must be removed first and

installed last when the battery

is disconnected. Disconnect

the battery charger in the fol-

lowing order:

After a jump start from a good bat-

tery, drive the vehicle for 20-30 min-

utes before it is shutoff. The vehicle

may not restart if you shut it off

before the battery had a chance to

adequately recharge. See "Jump

Starting" in chapter 6 for more infor-

mation on jump starting procedures.

The following items may need to be

reset after the battery has been dis-

charged or the battery has been dis-

connected. See chapter 3 or 4 for:

• Power Windows

• Trip Computer

• Climate Control System

• Clock

i

Information

• Audio System

• Sunroof

(1) Turn off the battery charg-

er main switch.

An inappropriately disposed

battery can be harmful to

the environment and human

health. Dispose of the bat-

tery according to your local

law(s) or regulations.

(2) Unhook

the

negative

clamp from the negative

battery terminal.

(3) Unhook the positive clamp

from the positive battery

terminal.

•

Always

use

a

genuine

7

HYUNDAI approved battery

when you replace the battery.

7-37

Maintenance

TIRES AND WHEELS

Tire Care

• Replace tires that are worn,

show uneven wear, or are dam-

aged. Worn tires can cause

loss of braking effectiveness,

steering control, or traction.

• ALWAYS replace tires with the

same size as each tire that

was originally supplied with

this vehicle. Using tires and

wheels other than the recom-

mended sizes could cause

unusual handling characteris-

tics, poor vehicle control, or

negatively affect your vehi-

cle's Anti-Lock Brake System

(ABS) resulting in a serious

accident.

WARNING

For proper maintenance, safety, and

maximum fuel economy, you must

always maintain recommended tire

inflation pressures and stay within

the load limits and weight distribution

recommended for your vehicle.

Tire failure may cause loss of

vehicle control resulting in an

accident. To reduce risk of

SERIOUS INJURY or DEATH,

take the following precautions:

• Inspect your tires monthly for

proper inflation as well as

wear and damage.

• The recommended cold tire

pressure for your vehicle can

be found in this manual and on

the tire label located on the dri-

ver's side center pillar. Always

use a tire pressure gauge to

measure tire pressure. Tires

with too much or too little

pressure wear unevenly caus-

ing poor handling.

OOS087003

• Check the pressure of the

spare every time you check

the pressure of the other tires

on your vehicle.

All specifications (sizes and pres-

sures) can be found on a label

attached to the driver's side center

pillar.

7-38

Recommended Cold Tire

Inflation Pressures

WARNING

CAUTION

All tire pressures (including the

spare) should be checked when the

tires are cold. "Cold tires" means the

vehicle has not been driven for at

least three hours or has been driven

for less than one mile (1.6 km).

Warm tires normally exceed recom-

mended cold tire pressures by 4 to 6

psi (28 to 41 kPa). Do not release air

from warm tires to adjust the pres-

sure or the tires will be under-inflat-

ed. For recommended inflation pres-

sure, refer to "Tire and Wheels" in

chapter 8.

Recommended pressures must

be maintained for the best ride,

vehicle handling, and minimum

tire wear.

Over-inflation or under-inflation

can reduce tire life, adversely

affect vehicle handling, and

lead to sudden tire failure that

could result in loss of vehicle

control resulting in an accident.

Severe under-inflation can lead

to severe heat build-up, causing

blowouts, tread separation and

other tire failures that can result

in the loss of vehicle control

resulting in an accident. This

risk is much higher on hot days

and when driving for long peri-

ods at high speeds.

• Under-inflation results in

excessive wear, poor handling

and reduced fuel economy.

Wheel deformation is also

possible. Keep your tire pres-

sures at the proper levels. If a

tire frequently needs refilling,

have it checked by an author-

ized HYUNDAI dealer.

• Over-inflation produces

a

harsh ride, excessive wear at

the center of the tire tread,

and a greater possibility of

damage from road hazards.

7

7-39

Maintenance

If you overfill the tire, release air by

pushing on the metal stem in the

center of the tire valve. Recheck the

tire pressure with the tire gauge. Be

sure to put the valve caps back on

the valve stems. Without the valve

cap, dirt or moisture could get into

the valve core and cause air leakage.

If a valve cap is missing, install a new

one as soon as possible.

A cold tire means the vehicle has

been sitting for 3 hours and driven for

less than 1 mile (1.6 km) in that 3

hour period.

Check Tire Inflation Pressure

Check your tires, including the spare

tire, once a month or more.

Tire Rotation

To equalize tread wear, HYUNDAI

recommends that the tires be rotated

according to the maintenance sched-

ule or sooner if irregular wear devel-

ops.

During rotation, check the tires for

correct balance.

When rotating tires, check for uneven

wear and damage. Abnormal wear is

usually caused by incorrect tire pres-

sure, improper wheel alignment, out-

of-balance wheels, severe braking or

severe cornering. Look for bumps or

bulges in the tread or side of the tire.

Replace the tire if you find any of

these conditions. Replace the tire if

fabric or cord is visible. After rotation,

be sure to bring the front and rear tire

pressures to specification and check

lug nut tightness (proper torque is

79~94 lbf·ft [11~13 kgf·m]).

How to check

Use a good quality tire pressure

gauge to check tire pressure. You

can not tell if your tires are properly

inflated simply by looking at them.

Radial tires may look properly inflat-

ed when they are under-inflated.

Remove the valve cap from the tire

valve stem. Press the tire gauge firm-

ly onto the valve to get a pressure

measurement. If the cold tire inflation

pressure matches the recommended

pressure on the tire label located on

the driver's side center pillar or in this

manual. No further adjustment is

necessary. If the pressure is low, add

air until you reach the recommended

pressure. Make sure to put the valve

caps back on the valve stems.

Without the valve cap, dirt or mois-

ture could get into the valve core and

cause air leakage. If a valve cap is

missing, install a new one as soon as

possible.

Allow the tire to cool before measur-

ing the inflation pressure. Always be

sure the tire is cold before inflating to

the recommended pressure.

7-40

■ Without a spare tire

Wheel Alignment and Tire

Balance

The wheels on your vehicle were

aligned and balanced carefully at the

factory to give you the longest tire life

and best overall performance.

i

Information

Tires that are asymmetrical or direc-

tional can only be installed on the

wheel in one direction. The outside

and inside of an asymmetrical tire is

not easily distinguishable. Pay careful

attention to the markings on the side- In most cases, you will not need to

walls of the tires, noting the "outside" have your wheels aligned again.

marking and also the rotating direc- However, if you notice unusual tire

tion before installing them on the wear or your vehicle pulling one way

vehicle.

or the other, the alignment may need

to be reset.

If you notice your vehicle vibrating

when driving on a smooth road, your

wheels may need to be rebalanced.

ODH073802

Disc brake pads should be inspected

for wear whenever tires are rotated.

WARNING

• Do not use the compact spare

tire for tire rotation.

NOTICE

• Do not mix bias ply and radial

ply tires under any circum-

stances. This may cause

unusual handling characteris-

tics that may cause loss of

vehicle control resulting in an

accident.

Improper wheel weights can dam-

age your vehicle's aluminum

wheels. Use only approved wheel

weights.

7

7-41

Maintenance

Tire Replacement

• Tires degrade over time, even

when they are not being used.

Regardless of the remaining

tread, HYUNDAI recommends

that tires be replaced after six

(6) years of normal service.

• When replacing tires (or

wheels), it is recommended to

replace the two front or two

rear tires (or wheels) as a pair.

Replacing just one tire can

seriously affect your vehicle's

handling. If only replacing one

pair of tires, it is recommend-

ed to install the pair of new

tires on the rear axle.

• Heat caused by hot climates

or frequent high loading con-

ditions can accelerate the

aging process. Failure to fol-

low this warning may cause

sudden tire failure, which

could lead to a loss of vehicle

control resulting in an acci-

dent.

WARNING

Tread wear indicator

To reduce the risk of DEATH or

SERIOUS INJURY:

• Replace tires that are worn,

show uneven wear, or are

damaged. Worn tires can

cause loss of braking effec-

tiveness, steering control, and

traction.

• Always replace tires with the

same size as each tire that

was originally supplied with

this vehicle. Using tires and

wheels other than the recom-

mended sizes could cause

unusual handling characteris-

tics, poor vehicle control, or

negatively affect your vehi-

cle's Anti-Lock Brake System

(ABS) resulting in a serious

accident.

OLMB073027

If the tire is worn evenly, a tread wear

indicator will appear as a solid band

across the tread. This shows there is

less than 2/32 inch (1.6 mm) of tread

left on the tire. Replace the tire when

this happens.

Do not wait for the tread surface to

become level with the tread wear

indicators before replacing the tire.

7-42

Compact spare tire replacement

Wheel Replacement

Tire Maintenance

A compact spare tire has a shorter

tread life than a regular size tire.

Replace it when you can see the

tread wear indicator bars on the tire.

The replacement compact spare tire

should be the same size and design

tire as the one provided with your

new vehicle and should be mounted

on the same compact spare tire

wheel. The compact spare tire is not

designed to be mounted on a regular

size wheel, and the compact spare

tire wheel is not designed for mount-

ing a regular size tire.

When replacing the metal wheels for In addition to proper inflation, correct

any reason, make sure the new wheel alignment helps to decrease

wheels are equivalent to the original tire wear. If you find a tire is worn

factory units in diameter, rim width unevenly, have your dealer check the

and offset.

wheel alignment.

When you have new tires installed,

make sure they are balanced. This

will increase vehicle ride comfort and

tire life. Additionally, a tire should

always be rebalanced if it is removed

from the wheel.

Tire Traction

Tire traction can be reduced if you

drive on worn tires, tires that are

improperly inflated or on slippery

road surfaces. Tires should be

replaced when the tread depth is at

least 2/32 inch (1.6 mm). To reduce

the possibility of losing control, slow

down whenever there is rain, snow or

ice on the road.

Tire Sidewall Labeling

This information identifies and

describes the fundamental charac-

teristics of the tire and also provides

the tire identification number (TIN)

for safety standard certification. The

TIN can be used to identify the tire in

case of a recall.

WARNING

The original tire should be

repaired or replaced as soon as

possible to avoid failure of the

spare and loss of vehicle con-

trol resulting in an accident.The

compact spare tire is for emer-

gency use only. Do not operate

your vehicle over 50 mph (80

km/h) when using the compact

spare tire.

7

7-43

Maintenance

Example tire size designation:

Wheel size designation

1

(These numbers are provided as an Wheels are also marked with impor-

example only; your tire size designa- tant information that you need if you

tor could vary depending on your ever have to replace one. The follow-

5,6

7

vehicle.)

ing explains what the letters and

numbers in the wheel size designa-

tion mean.

4

205/60R16 92H

Example wheel size designation:

6.5J x 16

2

205 - Tire width in millimeters.

3

60 - Aspect ratio. The tire's section

height as a percentage of its

width.

R - Tire construction code (Radial).

16 - Rim diameter in inches.

92 - Load Index, a numerical code

associated with the maximum

load the tire can carry.

H - Speed Rating Symbol. See the

speed rating chart in this section

for additional information.

1

OLMB073028

6.5 - Rim width in inches.

J - Rim contour designation.

16 - Rim diameter in inches.

1. Manufacturer or brand name

Manufacturer or brand name is

shown.

2. Tire size designation

A tire's sidewall is marked with a tire

size designation. You will need this

information when selecting replace-

ment tires for your car. The following

explains what the letters and num-

bers in the tire size designation

mean.

7-44

Tire speed ratings

3. Checking tire life (TIN :Tire

Identification Number)

4. Tire ply composition and

material

The chart below lists many of the dif-

ferent speed ratings currently being

used for passenger vehicle tires. The

speed rating is part of the tire size

designation on the sidewall of the

tire. This symbol corresponds to that

tire’s designed maximum safe oper-

ating speed.

Any tires that are over six years old, The number of layers or plies of rub-

based on the manufacturing date, ber-coated fabric in the tire. Tire

(including the spare tire) should be manufacturers also must indicate the

replaced by new ones. You can find materials in the tire, which include

the manufacturing date on the tire steel, nylon, polyester, and others.

sidewall (possibly on the inside of the The letter "R" means radial ply con-

wheel), displaying the DOT Code. struction; the letter "D" means diago-

The DOT Code is a series of num- nal or bias ply construction; and the

bers on a tire consisting of numbers letter "B" means belted-bias ply con-

and English letters. The manufactur- struction.

Speed

Rating

Maximum Speed

Symbol

ing date is designated by the last four

digits (characters) of the DOT code.

S

T

H

V

W

Y

112 mph (180 km/h)

118 mph (190 km/h)

130 mph (210 km/h)

149 mph (240 km/h)

168 mph (270 km/h)

186 mph (300 km/h)

5. Maximum permissible infla-

tion pressure

DOT : XXXX XXXX OOOO

This number is the greatest amount

of air pressure that should be put in

the tire. Do not exceed the maximum

permissible inflation pressure. Refer

to the Tire and Loading Information

label for recommended inflation

pressure.

The front part of the DOT shows a

plant code number, tire size and

tread pattern and the last four num-

bers indicate week and year manu-

factured.

7

For example:

DOT XXXX XXXX 1420 represents

that the tire was produced in the 14th

week of 2020.

7-45

Maintenance

Tread wear

Traction - AA, A, B & C

6. Maximum load rating

The tread wear grade is a compara- The traction grades, from highest to

tive rating based on the wear rate of lowest, are AA, A, B and C. Those

the tire when tested under controlled grades represent the tire's ability to

conditions on a specified govern- stop on wet pavement as measured

ment test course. For example, a tire under controlled conditions on spec-

graded 150 would wear one-and-a- ified government test surfaces of

half times (1½) as well on the gov- asphalt and concrete. A tire marked

ernment course as a tire graded 100. C may have poor traction perform-

This number indicates the maximum

load in kilograms and pounds that

can be carried by the tire. When

replacing the tires on the vehicle,

always use a tire that has the same

load rating as the factory installed

tire.

ance.

The relative performance of tires

7. Uniform tire quality grading

depends upon the actual conditions

Quality grades can be found where

applicable on the tire sidewall

between tread shoulder and maxi-

mum section width.

of their use, however, and may

WARNING

depart significantly from the norm

due to variations in driving habits,

service practices and differences in

road characteristics and climate.

The traction grade assigned to

this tire is based on straight-

ahead braking traction tests,

and does not include accelera-

tion, cornering, hydroplaning,

or peak traction characteristics.

For example:

TREAD WEAR 200

TRACTION AA

TEMPERATURE A

These grades are molded on the

sidewalls of passenger vehicle tires.

The tires available as standard or

optional equipment on your vehicle

may vary with respect to grade.

7-46

Temperature - A, B & C

Tire Terminology and

Definitions

WARNING

The temperature grades are A (the

highest), B and C representing the

tire’s resistance to the generation of

heat and its ability to dissipate heat

when tested under controlled condi-

tions on a specified indoor laboratory

test wheel.

Air Pressure

The temperature grade for this

tire is established for a tire that

is properly inflated and not

overloaded. Excessive speed,

under-inflation, over-inflation,

or excessive loading, either

separately or in combination,

can cause heat build-up and

possible sudden tire failure.

This may cause loss of vehicle

control resulting in an accident.

The amount of air inside the tire

pressing outward on the tire. Air

pressure is expressed in pounds per

square inch (psi) or kilopascal (kPa).

Sustained high temperature can

cause the material of the tire to

degenerate and reduce tire life, and

excessive temperature can lead to

Accessory Weight

This means the combined weight of

optional accessories. Some exam-

ples of optional accessories are

automatic transmission, power

seats, and air conditioning.

sudden tire failure. Grade

C

responds to a level of performance

which all passenger car tires must

meet under the Federal Motor

Vehicle Safety Standard No. 109.

Grades B and A represent higher

levels of performance on the labora-

tory test wheel than the minimum

required by law.

Aspect Ratio

The relationship of a tire's height to

its width.

7

Belt

A rubber coated layer of cords that is

located between the plies and the

tread. Cords may be made from steel

or other reinforcing materials.

7-47

Maintenance

Bead

DOT Markings

Kilopascal (kPa)

The tire bead contains steel wires A code molded into the sidewall of a The metric unit for air pressure.

wrapped by steel cords that hold the tire signifying that the tire is in com-

tire onto the rim.

pliance with the U.S. Department of

Transportation motor vehicle safety

standards. The DOT code includes

the Tire Identification Number (TIN),

an alphanumeric designator which

can also identify the tire manufactur-

er, production plant, brand and date

of production.

Light truck(LT) tire

A tire designated by its manufacturer

as primarily intended for use on light-

weight trucks or multipurpose pas-

senger vehicles.

Bias Ply Tire

A pneumatic tire in which the plies

are laid at alternate angles less than

90 degrees to the centerline of the

tread.

Load ratings

The maximum load that a tire is rated

to carry for a given inflation pressure.

Cold Tire Pressure

GVWR

Gross Vehicle Weight Rating

The amount of air pressure in a tire,

measured in pounds per square inch

(psi) or kilopascals (kPa) before a tire

has built up heat from driving.

Load Index

GAWR FRT

Gross Axle Weight Rating for the

Front Axle.

An assigned number ranging from 1

to 279 that corresponds to the load

carrying capacity of a tire.

Curb Weight

This means the weight of a motor

vehicle with standard and optional

equipment including the maximum Gross Axle Weight Rating for the

capacity of fuel, oil and coolant, but Rear axle.

without passengers and cargo.

Maximum Inflation Pressure

GAWR RR

The maximum air pressure to which

a cold tire may be inflated. The max-

imum air pressure is molded onto the

sidewall.

Intended Outboard Sidewall

The side of an asymmetrical tire, that

must always face outward when

mounted on a vehicle.

7-48

Maximum Load Rating

Passenger (P-Metric) tire

Recommended Inflation

Pressure

Vehicle manufacturer's recommend-

ed tire inflation pressure as shown

on the tire placard.

The load rating for a tire at the maxi- A tire used on passenger cars and

mum permissible inflation pressure some light duty trucks and multipur-

for that tire.

pose vehicles.

Maximum Loaded Vehicle

Weight

The sum of curb weight; accessory

weight; vehicle capacity weight; and

production options weight.

Ply

Radial Ply Tire

A layer of rubber-coated parallel

cords.

A pneumatic tire in which the ply

cords that extend to the beads are

laid at 90 degrees to the centerline of

the tread.

Pneumatic tire

A mechanical device made of rubber,

chemicals, fabric and steel or other

materials, that, when mounted on an

automotive wheel provides the trac-

tion and contains the gas or fluid that

sustains the load.

Normal Occupant Weight

Rim

The number of occupants a vehicle

is designed to seat multiplied by 150

pounds (68 kg).

A metal support for a tire and upon

which the tire beads are seated.

Occupant Distribution

Designated seating positions.

Sidewall

The portion of a tire between the

tread and the bead.

Pneumatic options weight

7

The combined weight of installed

regular production options weighing

over 5 lb. (2.3 kg) in excess of the

standard items which they replace,

not previously considered in curb

weight or accessory weight, includ-

ing heavy duty breaks, ride levelers,

roof rack, heavy duty battery, and

special trim.

Outward Facing Sidewall

Speed Rating

An asymmetrical tire has a particular

side that faces outward when mount-

ed on a vehicle. The outward facing

sidewall bears white lettering or

bears manufacturer, brand, and/or

model name molding that is higher or

deeper than the same moldings on

the inner facing sidewall.

An alphanumeric code assigned to a

tire indicating the maximum speed at

which a tire can operate.

7-49

Maintenance

Traction

Vehicle Capacity Weight

All Season Tires

The friction between the tire and the The number of designated seating

road surface.The amount of grip pro- positions multiplied by 150 lbs. (68

HYUNDAI specifies all season tires

on some models to provide good

performance for use all year round,

including snowy and icy road condi-

tions. All season tires are identified

by ALL SEASON and/or M+S (Mud

and Snow) on the tire sidewall. Snow

tires have better snow traction than

all season tires and may be more

appropriate in some areas.

vided.

kg) plus the rated cargo and luggage

load.

Tread

Vehicle Maximum Load on the

Tire

The portion of a tire that comes into

contact with the road.

Load on an individual tire due to curb

and accessory weight plus maximum

occupant and cargo weight.

Treadwear Indicators

Narrow bands, sometimes called

"wear bars", that show across the

tread of a tire when only 1/16 inch of

tread remains.

Summer Tires

Vehicle Normal Load on the Tire

HYUNDAI specifies summer tires on

some models to provide superior

performance on dry roads. Summer

tire performance is substantially

reduced in snow and ice. Summer

tires do not have the tire traction rat-

ing M+S (Mud and Snow) on the tire

side wall. If you plan to operate your

vehicle in snowy or icy conditions,

HYUNDAI recommends the use of

snow tires or all season tires on all

four wheels.

Load on an individual tire that is

determined by distributing to each

axle its share of the curb weight,

accessory weight, and normal occu-

pant weight and dividing by 2.

UTQGS

Uniform Tire Quality Grading

Standards is a tire information sys-

tem that provides consumers with

ratings for a tire's traction, tempera-

ture and treadwear. Ratings are

determined by tire manufacturers

using government testing proce-

dures. The ratings are molded into

the sidewall of the tire.

Vehicle Placard

A label permanently attached to a

vehicle showing the original equip-

ment tire size and recommended

inflation pressure.

7-50

Radial-ply tires have the same load

carrying capacity, as bias-ply or bias

belted tires of the same size, and use

the same recommended inflation

pressure. Mixing of radial-ply tires

with bias-ply or bias belted tires is

not recommended. Any combina-

tions of radial-ply and bias-ply or bias

belted tires when used on the same

vehicle will seriously deteriorate

vehicle handling. The best rule to fol-

low is: Identical pairs of radial-ply

tires should always be used as a set

for the front tires and a set for the

rear tires.

Longer wearing tires can be more

susceptible to irregular tread wear. It

is very important to follow the tire

rotation interval in this chapter to

achieve the tread life potential of

these tires. Cuts and punctures in

radial-ply tires are repairable only in

the tread area, because of sidewall

flexing. Consult your tire dealer for

radial-ply tire repairs.

Snow Tires

WARNING

If you equip your car with snow tires,

they should be the same size and

have the same load capacity as the

original tires. Snow tires should be

installed on all four wheels; other-

wise, poor handling may result. Snow

tires should carry 4 psi (28 kPa)

more air pressure than the pressure

recommended for the standard tires

on the tire label on the driver’s side of

the center pillar, or up to the maxi-

mum pressure shown on the tire

sidewall, whichever is less. Do not

drive faster than 75 mph (120 km/h)

when your vehicle is equipped with

snow tires.

Do not mix bias ply and radial

ply tires under any circum-

stances.This may cause unusu-

al handling characteristics that

may cause loss of vehicle con-

trol resulting in an accident.

Low Aspect Ratio Tires

The aspect ratio is lower than 50 on

low aspect ratio tires.

Because low aspect ratio tires are

optimized for handling and braking,

their sidewall is a little stiffer than a

standard tire. Also low aspect ratio

tires tend to be wider and conse-

quently have a greater contact patch

with the road surface. In some

instances they may generate more

road noise compared with standard

tires.

Radial-Ply Tires

Radial-ply tires provide improved

tread life, road hazard resistance and

smoother high speed ride. The radi-

al-ply tires used on this vehicle are of

belted construction, and are selected

to complement the ride and handling

characteristics of your vehicle.

7

7-51

Maintenance

CAUTION

Because the sidewall of a low

aspect ratio tire is shorter than

a standard tire, the rim of the

wheel and the tire itself is more

easily susceptible to damage.

Use caution when driving and

follow the guidelines below to

help minimize damage to the

wheel and tire:

- When driving on a rough road

or off road, drive cautiously

because tires and wheels may

be damaged. And after driving,

inspect tires and wheels.

• It is not easy to recognize tire

damage with your own eyes.

But if there is the slightest

hint of tire damage, have the

tire checked or replaced

because the tire damage may

cause air leakage from the

tire.

• If the tire is damaged by driv-

ing on a rough road, off road,

pothole, manhole, or curb

stone, it will not be covered by

the warranty.

- When passing over a pothole,

speed bump, manhole, or curb

stone, drive slowly so that the

tires and wheels are not dam-

aged.

- If the tire is subjected to a

severe impact, have the tire

and wheel inspected by an

authorized HYUNDAI dealer.

- Inspect the tire condition and

pressure every 1,800 miles

(3,000km).

7-52

FUSES

■ Blade type

A vehicle's electrical system is pro-

tected from electrical overload dam-

age by fuses.

WARNING

NEVER replace a fuse with any-

thing but another fuse of the

same rating.

• A higher capacity fuse could

cause damage and possibly

cause a fire.

• Do not install a wire or alu-

minum foil instead of the

proper fuse - even as a tem-

porary repair. It may cause

extensive wiring damage and

possibly a fire.

This vehicle has 2 (or 3) fuse panels,

one located in the driver's side panel

bolster, the other in the engine com-

partment near the battery.

If any of your vehicle's lights, acces-

sories, or controls do not work, check

the appropriate circuit fuse. If a fuse

has blown, the element inside the

fuse will be melted or broken.

If the electrical system does not

work, first check the driver's side

fuse panel. Before replacing a blown

fuse, turn the engine and all switches

off, and then disconnect the negative

battery cable. Always replace a

blown fuse with one of the same rat-

ing.

If the replacement fuse blows, this

indicates an electrical problem. Avoid

using the system involved and imme-

diately consult an authorized

HYUNDAI dealer.

Normal

Blown

■ Cartridge type

Normal

Blown

■ Multi fuse

NOTICE

Do not use a screwdriver or any

other metal object to remove

fuses because it may cause a

short circuit and damage the sys-

tem.

Normal

Blown

7

Blown

Normal

OLF074075

7-53

Maintenance

In an emergency, if you do not have

a spare fuse, use a fuse of the same

rating from a circuit you may not

need for operating the vehicle.

Instrument Panel Fuse

Replacement

If the headlamps or other electrical

components do not work and the

fuses are undamaged, check the

fuse panel in the engine compart-

ment. If a fuse is blown, it must be

replaced with the same rating.

OOS077026

5. Pull the suspected fuse straight

out. Use the removal tool provided

in the engine compartment fuse

panel.

OOS077028

1. Turn the engine off.

2. Turn all other switches OFF.

3. Open the fuse panel cover.

4. Refer to the label on the inside of

the fuse panel cover to locate the

suspected fuse location.

6. Check the removed fuse; replace it

if it is blown. Spare fuses are pro-

vided in the instrument panel fuse

panels (or in the engine compart-

ment fuse panel).

7. Push in a new fuse of the same

rating, and make sure it fits tightly

in the clips. If it fits loosely, consult

an authorized HYUNDAI dealer.

7-54

Fuse switch

Engine Compartment Panel

Fuse Replacement

i

Information

■ Blade type fuse

OOS077027

OOS047142L

OOS077024

Always, place the fuse switch to the

ON position.

If you move the switch to the OFF

position, some items such as the

audio system and digital clock must

be reset and the smart key may not

work properly.

If the fuse switch is OFF, the above

message will appear.

■ Cartridge type fuse

NOTICE

• Always place the fuse switch in

the ON position while driving the

vehicle.

7

• Do not move the fuse switch

repeatedly. The fuse switch may

be damaged.

OOS077025

1. Turn the engine off.

2. Turn all other switches OFF.

7-55

Maintenance

3. Remove the fuse panel cover by

pressing the tap and pulling up.

Main fuse

Multi fuse

4. Check the removed fuse; replace it

if it is blown. To remove or insert

the fuse, use the fuse puller in the

engine compartment fuse panel.

5. Push in a new fuse of the same

rating, and make sure it fits tightly

in the clips. If it fits loosely, consult

an authorized HYUNDAI dealer.

CAUTION

OOS077022

OOS077023

After checking the fuse box in

the engine compartment secure-

ly close the fuse box cover

inside the engine compartment,

until it clicks.

If the fuse box is not closed

properly, water may leak in side,

possibly causing a malfunction

with the electrical system.

If the multi fuse is blown, it must be

removed as follows:

1. Turn off the engine.

2. Disconnect the negative battery

cable.

3. Remove the fuse panel cover by

pressing the tab and pulling it up.

If the main fuse is blown, it must be

removed as follows:

1. Turn off the engine.

2. Disconnect the negative battery

cable.

3. Remove the fuse panel cover by

pressing the tab and pulling it up.

4. Remove the nuts shown in the pic-

ture above.

4. Remove the nuts shown in the pic-

ture above.

5. Replace the fuse with a new one

of the same rating.

5. Replace the fuse with a new one

of the same rating.

6. Reinstall in the reverse order of

removal.

6. Reinstall in the reverse order of

removal.

i

Information

i

Information

If the main fuse is blown, consult an

authorized HYUNDAI dealer.

If the multi fuse is blown, consult an

authorized HYUNDAI dealer.

7-56

Fuse/Relay Panel Description

Instrument panel fuse panel

OOS077028

Inside the fuse/relay box cover, you

can find the fuse/relay label describ-

ing fuse/relay names and ratings.

i

Information

7

Not all fuse panel descriptions in this

manual may be applicable to your

vehicle; the information is accurate at

the time of printing. When you inspect

the fuse box on your vehicle, refer to

the fuse box label.

OOS077078N

7-57

Maintenance

Instrument panel fuse panel

Fuse Name

Fuse Rating

Protected Component

ATM Shift Lever IND., Electro Chromic Mirror, AMP, A/V & Navigation Head Unit, A/C Control Module,

Front Air Ventilation Seat Module, Front Seat Warmer Module

MODULE 5

7.5A

MODULE 3

SUNROOF

7.5A

20A

10A

25A

15A

25A

7.5A

20A

Stop Lamp Switch, BCM, ATM Shift Lever

Sunroof Unit

TAIL GATE

OPEN

Tail Gate Relay

P/WINDOW

LH

Power Window LH Relay, Driver Safety Power Window Module

A/V & Navigation Head Unit

MULTI MEDIA

P/WINDOW

RH

Power Window RH Relay, Passenger Safety Power Window Module

Driver Seat Manual Switch

P/SEAT (DRV)

P/SEAT

(PASS)

Passenger Seat Manual Switch

Blind-Spot Collision Warning Unit LH/RH, Active Air Flap, BCM, Parking Distance Warning Buzzer,

Lane Keeping Assist Unit (Line), 4WD ECM

MODULE 4

PDM3

Smart Key Control Module, Immobilizer Module

ICM Relay Box(Power Outlet Relay)

POWER

OUTLET 2

7-58

Instrument panel fuse panel

Fuse Name

Fuse Rating

Protected Component

INTERIOR

LAMP

Glove Box Lamp, Vanity Lamp LH/RH, Room Lamp, Overhead Console Lamp, Wiresess Charger Unit,

Driver Console Switch, Luggage Lamp

7.5A

B/ALARM

HORN

10A

ICM Relay Box(Burglar Alarm Horn Relay)

MEMORY

AMP

A/C Control Module, Head Up Display, Instrument Cluster, Electro Chromic Mirror

AMP

30A

MODULE 6

MDPS

7.5A

Smart Key Control Module, BCM

MDPS Unit

MODULE 1

MODULE 7

A/BAG IND

Active Air Flap, Ignition key Interlock Switch, BCM, Hazard Switch, Data Link Connector, Rain sensor

Front Air Ventilation Seat Module, Front Seat Warmer Module

Instrument Cluster, A/C Control Modulee

7

BRAKE

SWITCH

Stop Lamp Switch, Smart Key Control Module

Transaxle Range Switch(A/T), ECM, ICM Relay Box(Burglar Alarm Relay)

Head Up Display, Instrument Cluster

START

CLUSTER

7-59

Maintenance

Instrument panel fuse panel

Fuse Name

Fuse Rating

Protected Component

DOOR LOCK

20A

Door Lock Relay, Door Unlock Relay, ICM Relay Box(Two Turn Unlock Relay)

PDM 2

FCA

7.5A

10A

20A

7.5A

15A

25A

10A

15A

10A

Start/Stop Button Switch, Immobilizer Module

Forward Collision Avoidance Assist Unit

S/HEATER

A/C 2

Front Seat Warmer Module, Front Air Ventilation Seat Module

A/C Control Module, Blower Motor, Blower Resistor, E/R Junction Block (Blower Relay)

A/C Control Module, E/R Junction Block(PTC Heater #2 Relay, Blower Relay, PTC Heater #1 Relay)

Smart Key Control Module

A/C 1

PDM 1

AIR BAG

IG1

SRS Control Module, Passenger Occupant Detection Sensor

PCB Block(FUSE : ABS 3, ECU 5, SENSOR 4, TCU 2)

Wiresess Charger Unit, Smart Key Control Module, BCM, A/V & Navigation Head Unit,

ICM Relay Box(Power Outlet Relay), Power Outside Mirror Switch, AMP

MODULE2

WASHER

Muntifunction Switch

WIPER

(LO/HI)

BCM, PCB Block (Front Wiper (Low) Relay), Front Wiper Motor

7-60

Instrument panel fuse panel

Fuse Name

Fuse Rating

Protected Component

WIPER RR

15A

Rear Wiper Relay, Rear Wiper Motor

WIPER FRT

25A

10A

20A

15A

Front Wiper Motor, PCB Block(Front Wiper(Low) Relay)

HEATED

MIRROR

Driver/Passenger Power Outside Mirror, A/C Control Module, ECM

POWER

OUTLET 1

Cigarette Lighter

BCM

HEATED

STEERING

7

7-61

Maintenance

Engine compartment fuse panel

OOS077029

Inside the fuse/relay box cover, you

can find the fuse/relay label describ-

ing fuse/relay names and ratings.

i

Information

Not all fuse panel descriptions in this

manual may be applicable to your

vehicle; the information is accurate at

the time of printing. When you inspect

the fuse panel in your vehicle, refer to

the fuse panel label.

OOS077079N

7-62

Engine compartment fuse panel

Fuse Name

Fuse Rating

Protected Component

ALT

150A

E/R Junction Block (Fuse - ABS 1, ABS 2, 4WD), Alternator

MDPS

B+5

80A

60A

MDPS Unit

PCB Block ((Fuse - HORN, H/LAMP HI, A/C, ECU 4, ECU 3), Engine Control Relay)

IGPM ((Fuse - S/HEATER), IPS0, IPS1, IPS2)

IGPM (IPS3, IPS4, IPS5, IPS6, IPS7, IPS8)

B+2

60A

B+3

60A

IGPM (Fuse - P/WINDOW LH, P/WINDOW RH, TAIL GATE OPEN, SUNROOF, B/ALARM HORN,

POWER OUTLET 2, AMP, P/SEAT (PASS),P/SEAT (DRV))

B+4

50A

COOLING

FAN

60A/50A

40A

E/R Junction Block (Cooling Fan #2 Relay, Cooling Fan #1 Relay)

E/R Junction Block (Rear Defogger Relay)

REAR

HEATED

7

BLOWER

IG1

40A

E/R Junction Block (Blower Relay)

W/O Smark Key : Ignition Switch

With Smark Key : E/R Junction Block (PDM #3 (IG1) Relay, PDM #2 (ACC) Relay)

40A

W/O Smark Key : Ignition Switch, E/R Junction Block (Srart #1 Relay)

With Smark Key : E/R Junction Block (PDM #4 (IG2) Relay, Srart #1 Relay)

IG2

40A

PTC

HEATER 1

50A

E/R Junction Block (PTC Heater #1 Relay)

E/R Junction Block (PTC Heater #2 Relay)

PTC

HEATER 2

50A

7-63

Maintenance

Engine compartment fuse panel

Fuse Name

Fuse Rating

Protected Component

TCU 1

15A

TCM

VACUUM

PUMP

20A

40A

20A

40A

30A

Vacuum Pump

FUEL PUMP

B+1

E/R Junction Block (Fuel Pump Relay)

IGPM ((Fuse - BRAKE SWITCH, PDM 1, DOOR LOCK, MODULE 1, PDM 2), Leak Current Autocut Device)

DCT1

TCM

DCT2

TCM

4WD

4WD ECM

ABS 1

ABS 2

ESC Control Module, Multipurpose Check Connector

ESC Control Module

7-64

Engine compartment fuse panel

■ GAMMA 1.6L T-GDI

Fuse Name

Fuse Rating

Protected Component

PCB Block (A/CON Relay), E/R Junction Block (Cooling Fan #1 Relay), Purge Control Solenoid Valve,

RCV Control Solenoid Valve, Oil Control Valve #1~#2, Canister Close Valve

SENSOR 2

10A

ECU 2

ECU 1

10A

20A

15A

20A

15A

10A

15A

10A

15A

10A

15A

ECM

INJECTOR

SENSOR 1

IGN COIL

ECU 3

-

Oxygen Sensor (Up), Oxygen Sensor (Down)

Ignition Coil #1~#4

ECM

A/C

PCB Block (A/CON Relay)

ECU 5

ECM

7

SENSOR 4

ABS 3

Vacuum Pump

ESC Control Module, Multipurpose Check Connector

TCM, Transaxle Range Switch

E/R Junction Block (Fuel Pump Relay)

ECM

TCU 2

SENSOR 3

ECU 4

7-65

Maintenance

Fuse Name

Fuse Rating

Protected Component

H/LAMP HI

10A

PCB Block (Head Lamp(High) Relay)

PCB Block (Horn Relay)

HORN

15A

Engine compartment fuse panel

■ NU 2.0L MPI

Fuse Name

Fuse Rating

Protected Component

PCB Block (A/CON Relay), E/R Junction Block (Cooling Fan #2 Relay, Cooling Fan #1 Relay),

Purge Control Solenoid Valve, Electronic Thermostat, Variable Intake Solenoid Valve, Oil Control Valve #1~#3,

Canister Close Valve

SENSOR 2

10A

ECU 2

ECU 1

10A

20A

15A

20A

15A

-

PCM

INJECTOR

SENSOR 1

IGN COIL

ECU 3

Injector #1~#4

Oxygen Sensor (Up), Oxygen Sensor (Down)

Ignition Coil #1~#4

PCM

7-66

Fuse Name

Fuse Rating

Protected Component

A/C

10A

PCB Block (A/CON Relay)

ECU 5

SENSOR 4

ABS 3

10A

15A

10A

15A

10A

15A

10A

15A

PCM

-

Multipurpose Check Connector, ESC Control Module

Transaxle Range Switch

TCU 2

SENSOR 3

ECU 4

E/R Junction Block (Fuel Pump Relay)

PCM

H/LAMP HI

HORN

PCB Block (Head Lamp(High) Relay)

PCB Block (Horn Relay)

7

7-67

Maintenance

Engine compartment fuse panel

(Battery terminal cover)

OOS077035

Inside the fuse/relay box cover, you

can find the fuse/relay label describ-

ing fuse/relay names and ratings.

i

Information

Not all fuse panel descriptions in this

manual may be applicable to your

vehicle; the information is accurate at

the time of printing. When you inspect

the fuse panel in your vehicle, refer to

the fuse panel label.

OPD076065

NOTICE

After checking the fuse panel in the engine compartment, securely

install the cover. If it is not securely latched, electrical failure may occur

from water contact.

7-68

LIGHT BULBS

Consult an authorized HYUNDAI

dealer to replace most vehicle light

bulbs. It is difficult to replace vehicle

light bulbs because other parts of the

vehicle must be removed before you

can get to the bulb. This is especially

true for removing the headlamp

assembly to get to the bulb(s).

Headlamp, Position lamp,

Daytime Running Light, Turn

signal lamp, Cornering lamp

and Side marker

WARNING

• Prior to replacing a lamp,

depress the foot brake, move

the shift lever into P (Park)

apply the parking brake, place

the ignition switch to the

LOCK/OFF position, and take

the key with you when leaving

the vehicle to avoid sudden

movement of the vehicle and

to prevent possible electric

shock.

Type A

Removing/installing the headlamp

assembly can result in damage to

the vehicle.

i

Information

• Be aware the bulbs may be

hot and may burn your fin-

gers.

The headlamp and tail lamp lenses

could appear frosty if the vehicle is

washed after driving or the vehicle is

driven at night in wet weather. This

condition is caused by temperature

difference between the lamp inside

and outside and, it does not indicate a

problem with your vehicle. When

moisture condenses in the lamp, it will

be removed after driving with the

headlamp on. The removable level

may differ depending on lamp size,

lamp position and environmental con-

dition. However, if moisture is not

removed, we recommend that your

vehicle is inspected by an authorized

HYUNDAI dealer.

OOS077033N

(1) Headlamp (Low)

(2) Headlamp (High)

(3) Daytime running light (if equipped)

/Position lamp

7

(4) Turn signal lamp

(5) Front fog lamp (if equipped)

(6) Side marker

(7) Side reflex reflector

7-69

Maintenance

■ High/Low beam

• Always handle them carefully, and

avoid scratches and abrasions. If

the bulbs are lit, avoid contact with

liquids.

WARNING

• Never touch the glass with bare

hands. Residual oil may cause the

bulb to overheat and burst when lit.

• A bulb should be operated only

when installed in a headlamp.

• If a bulb becomes damaged or

cracked, replace it immediately

and carefully dispose of it.

OOS077034

OLMB073042L

[1] : High beam, [2] : Low beam

• Handle halogen bulbs with

care. Halogen bulbs contain

pressurized gas that will pro-

duce flying pieces of glass that

could cause injuries if broken.

• Wear eye protection when

changing a bulb. Allow the

bulb to cool down before han-

dling it.

1. Open the hood.

2. Disconnect the negative battery

cable.

3. Remove the headlamp bulb cover

by turning it counterclockwise.

4. Disconnect the headlamp bulb

socket-connector.

7-70

5. Remove the bulb from the head-

lamp assembly.

6. Install a new headlamp bulb and

snap the headlamp bulb retaining

wire into position by aligning the

wire with the groove on the bulb.

5. Install a new bulb by inserting it

into the socket and rotating it until

it locks into place.

6. Install the socket in the assembly

by aligning the tabs on the socket

with the slots in the assembly.

7. Connect the headlamp bulb sock-

et-connector.

7. Push the socket into the assembly

and turn the socket clockwise.

8. Install the headlamp bulb cover by

turning it clockwise.

Position lamp and daytime running

light

OOS077038

i

Information

Your vehicle is equipped with LED

lamps. LED lamps do not have

replaceable bulbs. If the LED lamp

does not operate, have the vehicle

checked by an authorized HYUNDAI

dealer.

Turn signal

The headlamp aiming should be

adjusted after an accident or after the

headlamp assembly is reinstalled at an

authorized HYUNDAI dealer.

1. Open the hood.

2. Disconnect the negative battery

cable.

3. Remove the socket (1) from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

4. Remove the bulb from the socket

by pressing it in and rotating it

counterclockwise until the tabs on

the bulb align with the slots in the

socket. Pull the bulb out of the

socket.

Side marker

If the light bulb does not operate,

have the vehicle checked by an

authorized HYUNDAI dealer.

7

7-71

Maintenance

• Always handle them carefully, and

avoid scratches and abrasions. If

the bulbs are lit, avoid contact with

liquids.

Type B

WARNING

• Never touch the glass with bare

hands. Residual oil may cause the

bulb to overheat and burst when lit.

• A bulb should be operated only

when installed in a headlamp.

• If a bulb becomes damaged or

cracked, replace it immediately

and carefully dispose of it.

OLMB073042L

OOS078052N

• Handle halogen bulbs with

care. Halogen bulbs contain

pressurized gas that will pro-

duce flying pieces of glass that

could cause injuries if broken.

• Wear eye protection when

changing a bulb. Allow the

bulb to cool down before han-

dling it.

(1) Headlamp (Low/High)

(2) Cornering light

(3) Daytime running light (if equipped)

/Position lamp

(4) Turn signal lamp

(5) Front fog lamp (if equipped)

(6) Side marker

Headlamp

Your vehicle is equipped with LED

lamps. LED lamps do not have

replaceable bulbs. If the LED lamp

does not operate, have the vehicle

checked by an authorized HYUNDAI

dealer.

(7) Side reflex reflector

7-72

5. Insert a new bulb by inserting it

into the socket and rotating it until

it locks into place.

6. Install the socket in the assembly

by aligning the tabs on the socket

with the slots in the assembly.

7. Push the socket into the assembly

and turn the socket clockwise.

OOS077037

OOS077038

Cornering Lamp

1. Open the hood.

Turn signal

1. Open the hood.

2. Disconnect the negative battery

cable.

2. Disconnect the negative battery

cable.

3. Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

3. Remove the socket (1) from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

7

4. Remove the bulb from the socket

by pressing it in and rotating it

counterclockwise until the tabs on

the bulb align with the slots in the

socket.

4. Remove the bulb from the socket

by pressing it in and rotating it

counterclockwise until the tabs on

the bulb align with the slots in the

socket. Pull the bulb out of the

socket.

Pull the bulb out of the socket.

7-73

Maintenance

5. Install a new bulb by inserting it

into the socket and rotating it until

it locks into place.

6. Install the socket in the assembly

by aligning the tabs on the socket

with the slots in the assembly.

5. Install a new bulb-socket into the

housing by aligning the tabs on the

socket with the slots in the housing.

Push the socket into the housing

and turn the socket clockwise.

Front fog lamp (if equipped)

7. Push the socket into the assembly

and turn the socket clockwise.

Side Repeater Lamp

Replacement

Position lamp and daytime running

light

Your vehicle is equipped with LED

lamps. LED lamps do not have

replaceable bulbs. If the LED lamp

does not operate, have the vehicle

checked by an authorized HYUNDAI

dealer.

OOS077059L

1. Loosen the pin-type retainers of the

under cover and then remove the

undercover.

2. Reach your hand into the back of the

front bumper.

Side marker

If the light bulb does not operate,

have the vehicle checked by an

authorized HYUNDAI dealer.

3. Disconnect the power connector

from the socket.

4. Remove the bulb-socket from the

housing by turning the socket coun-

terclockwise until the tabs on the

socket align with the slots of the

housing.

OOS077039

If the light bulb does not operate,

have the vehicle checked by an

authorized HYUNDAI dealer.

7-74

(3) Turn signal lamp

(4) Backup lamp

(5) Side marker

Rear Combination Light Bulb

Replacement

■ Type A (Standard)

OOS077066L

Stop/Tail lamp

1. Open the liftgate.

OOS077040N

■ Type B (LED)

2. Open the lamp assembly retaining

screw covers.

3. Loosen the lamp assembly retain-

ing screws with a cross-tip screw-

driver.

7

OOS078041N

(1) Stop/Tail lamp

(2) Tail lamp (Type A),

Stop/Tail lamp (Type B)

7-75

Maintenance

8. Install the socket into the assem- 4. Remove the socket from the

bly by aligning the tabs on the

socket with the slots in the assem-

bly. Push the socket into the

assembly and turn the socket

clockwise.

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

5. Remove the bulb from the socket

by pressing it in and rotating it

counterclockwise until the tabs on

the bulb align with the slots in the

socket. Pull the bulb out of the

socket.

9. Reinstall the lamp assembly to the

body of the vehicle.

OOS077068L

6. Insert a new bulb by inserting it

into the socket and rotating it until

it locks into place.

7. Install the socket into the assem-

bly by aligning the tabs on the

socket with the slots in the assem-

bly. Push the socket into the

assembly and turn the socket

clockwise.

4. Remove the rear combination

lamp assembly from the body of

the vehicle.

5. Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

6. Remove the bulb from the socket

by pressing it in and rotating it

counterclockwise until the tabs on

the bulb align with the slots in the

socket. Pull the bulb out of the

socket.

OOS077069L

Tail lamp (Type A)

8. Reinstall the lamp assembly to the

body of the vehicle.

1. Turn off the engine.

2. Open the tailgate.

3. Remove the service cover using a

flat-blade screwdriver.

7. Insert a new bulb by inserting it

into the socket and rotating it until

it locks into place.

7-76

Tail / Stop lamp (Type B)

7. Remove the high mounted stop

lamp after removing the mounting

nuts.

High Mounted Stop Lamp

Replacement

Your vehicle is equipped with LED

lamps. LED lamps do not have

replaceable bulbs. If the LED lamp

does not operate, have the vehicle

checked by an authorized HYUNDAi

dealer.

8. Install a new lamp

9. Reinstall the rear spoiler and the

liftgate upper trim in the reverse

order.

Turn signal lamp / Back up lamp

If the light bulb does not operate,

have the vehicle checked by an

authorized HYUNDAI dealer.

OOS077042

Side marker

1. Open the liftgate.

Your vehicle is equipped with LED

lamps. LED lamps do not have

replaceable bulbs. If the LED lamp

does not operate, have the vehicle

checked by an authorized HYUNDAI

dealer.

2. Gently remove the cover of the lift-

gate trim.

3. Remove the spoiler plug hole.

4. Disconnect the connector and

remove the washer hose and the

plug holes.

7

5. Remove the mounting nuts.

6. Remove the rear spoiler assembly.

7-77

Maintenance

License Plate Light Bulb

Replacement

Interior Light Bulb Replacement

Map lamp, Room lamp, Vanity mirror lamp, Luggage compartment

lamp and Glove box lamp

■ Map lamp (Type A)

■ Room lamp (Type A)

OOS077043

OOS077053

OOS077054

1. Using a flat-blade screwdriver,

gently pry the lens cover from the

lamp housing.

■ Map lamp (Type B)

■ Room lamp (Type B)

2. Remove the bulb by pulling it

straight out.

3. Install a new bulb.

4. Reinstall in the reverse order.

OOS077044

OOS077045

7-78

■ Vanity mirror lamp

■ Glove box lamp

3. Install a new bulb in the socket.

4. Align the lens tabs with the interi-

or lamp housing notches and snap

the lens into place.

NOTICE

Use care not to dirty or damage

lens, lens tab, and plastic hous-

ings.

OOS077046

OOS077047

■ Luggage compartment lamp

1. Using a flat-blade screwdriver,

gently pry the lens from the interi-

or lamp housing.

2. Remove the bulb by pulling it

straight out.

WARNING

7

Prior to working on the Interior

Lights, ensure that the "OFF"

button is depressed to avoid

burning your fingers or receiv-

ing an electric shock.

OOS077048

7-79

Maintenance

APPEARANCE CARE

Exterior Care

Protecting your vehicle's finish

Washing

WARNING

Exterior general caution

To help protect your vehicle’s finish

from rust and deterioration, wash it

thoroughly and frequently at least

once a month with lukewarm or cold

water.

If you use your vehicle for off-road

driving, you should wash it after each

off-road trip. Pay special attention to

the removal of any accumulation of

salt, dirt, mud, and other foreign

materials. Make sure the drain holes

in the lower edges of the doors and

rocker panels are kept clear and

clean.

Insects, tar, tree sap, bird droppings,

industrial pollution and similar

deposits can damage your vehicle’s

finish if not removed immediately.

Even prompt washing with plain

water may not completely remove all

these deposits. A mild soap, safe for

use on painted surfaces, should be

used.

After washing the vehicle, test

the brakes while driving slowly

to see if they have been affected

by water before getting on the

road. If braking performance is

impaired, dry the brakes by

applying them lightly while

maintaining a slow forward

speed.

It is very important to follow the label

directions when using any chemical

cleaner or polish. Read all warning

and caution statements that appear

on the label.

High-pressure washing

• When using high-pressure wash-

ers, make sure to maintain suffi-

cient distance from the vehicle.

Insufficient clearance or excessive

pressure can lead to component

damage or water penetration.

• Do not spray the camera, sensors

or its surrounding area directly with

a high pressure washer. Shock

applied from high pressure water

may cause the device to not oper-

ate normally.

• Do not bring the nozzle tip close to

boots (rubber or plastic covers)or

connectors as they may be dam-

aged if they come into contact with

high pressure water.

• Do not use any high-pressure noz-

zles, which induce either one-direct

water stream or water swirling.

NOTICE

• Do not use strong soap, chemi-

cal detergents or hot water, and

do not wash the vehicle in direct

sunlight or when the body of the

vehicle is warm.

• Be careful when washing the

side windows of your vehicle.

Especially, with high-pressure

water, water may leak through

the windows and wet the interi-

or.

• To prevent damage to the plastic

parts, do not clean with chemi-

cal solvents or strong deter-

gents.

After washing, rinse the vehicle thor-

oughly with lukewarm or cold water.

Do not allow soap to dry on the fin-

ish.

7-80

Waxing

NOTICE

A good coat of wax provides a barri-

er between your paint and environ-

mental contamination.

Keeping a good coat of wax on your

vehicle will help protect it.

Matte paint finish vehicle

(if equipped)

Automatic car wash which uses

rotating brushes should not be

used as this can damage the sur-

face of your vehicle. A steam

cleaner which washes the vehicle

surface at high temperature may

result the oil to adhere and leave

stains that is difficult to remove.

Use a soft cloth (e.g. microfiber

towel or sponge) when washing

your vehicle and dry with a

microfiber towel. When you hand

wash your vehicle, you should not

use a cleaner that finishes with

wax. If the vehicle surface is too

dirty (sand, dirt, dust, contami-

nant, etc.), clean the surface with

water before washing the car.

Wax the vehicle when water will no

longer bead on the paint.

Always wash and dry the vehicle

before waxing. Use a good quality

liquid or paste wax, and follow the

manufacturer’s instructions. Wax all

metal trim to protect it and to main-

tain its luster.

Removing oil, tar, and similar materi-

als with a spot remover will usually

strip the wax from the finish. Be sure

to re-wax these areas even if the rest

of the vehicle does not yet need wax-

ing.

OOS077051

NOTICE

• Water washing in the engine

compartment including high

pressure water washing may

cause the failure of electrical cir-

cuits located in the engine com-

partment.

7

• Never allow water or other liq-

uids to come in contact with

electrical/electronic

compo-

nents inside the vehicle as this

may damage them.

7-81

Maintenance

Repairing your vehicle's finish

Bright-metal maintenance

NOTICE

Deep scratches or stone chips in the • To remove road tar and insects,

• Wiping dust or dirt off the body

with a dry cloth will scratch the

finish.

painted surface must be repaired

promptly. Exposed metal will quickly

rust and may develop into a major

repair expense.

use a tar remover, not a scraper or

other sharp object.

• To protect the surfaces of bright-

metal parts from corrosion, apply a

coating of wax or chrome preser-

vative and rub to a high luster.

• Do not use steel wool, abrasive

cleaners, or strong detergents

containing highly alkaline or

caustic agents on chrome-plat-

ed or anodized aluminum parts.

This may result in damage to the

protective coating and cause

discoloration or paint deteriora-

tion.

NOTICE

• During winter weather or in coastal

areas, cover the bright metal parts

with a heavier coating of wax or

preservative. If necessary, coat the

parts with non-corrosive petroleum

jelly or other protective compound.

If your vehicle is damaged and

requires any metal repair or

replacement, be sure the body

shop applies anti-corrosion mate-

rials to the parts repaired or

replaced.

NOTICE

Underbody maintenance

NOTICE

Matte paint finish vehicle

(if equipped)

Corrosive materials used for ice and

snow removal and dust control may

collect on the underbody. If these

Matte paint finish vehicle

(if equipped)

Do not use any polish protector

such as a detergent, an abrasive

and a polish. In case wax is

applied, remove the wax immedi-

ately using a silicon remover and

if any tar or tar contaminant is on

the surface use a tar remover to

clean. However, be careful not to

apply too much pressure on the

painted area.

In case of matte paint finish vehi- materials are not removed, acceler-

cles, it is impossible to modify ated rusting can occur on underbody

only the damaged area and repair parts such as the fuel lines, frame,

of the whole part is necessary. If floor pan and exhaust system, even

the vehicle is damaged and paint- though they have been treated with

ing is required, we recommend rust protection.

that you have your vehicle main-

tained and repaired by an author-

ized HYUNDAI dealer. Take

extreme care, as it is difficult to

restore the quality after the repair.

7-82

Thoroughly flush the vehicle under-

body and wheel openings with luke-

warm or cold water once a month,

after off-road driving and at the end

of each winter. Pay special attention

to these areas because it is difficult

to see all the mud and dirt. It will do

more harm than good to wet down

the road grime without removing it.

The lower edges of doors, rocker

panels, and frame members have

drain holes that should not be

allowed to clog with dirt; trapped

water in these areas can cause rust-

ing.

Aluminum wheel maintenance

Corrosion protection

The aluminum wheels are coated Protecting your vehicle from corro-

with a clear protective finish.

sion

By using the most advanced design

and construction practices to combat

corrosion, HYUNDAI produces vehi-

cles of the highest quality. However,

this is only part of the job. To achieve

the long-term corrosion resistance

your vehicle can deliver, the owner’s

cooperation and assistance is also

required.

NOTICE

• Do not use abrasive cleaner, pol-

ishing compound, solvent, or

wire brushes on aluminum

wheels.

• Clean the wheel when it has

cooled.

• Use only a mild soap or neutral

detergent, and rinse thoroughly

with water. Also, clean the

wheels after driving on salted

roads.

• Do not wash the wheels with

high-speed car wash brushes.

Common causes of corrosion

The most common causes of corro-

sion on your vehicle are:

• Road salt, dirt and moisture that is

allowed to accumulate underneath

the vehicle.

• Removal of paint or protective

coatings by stones, gravel, abra-

sion or minor scrapes and dents

which leave unprotected metal

exposed to corrosion.

WARNING

After washing the vehicle, test

the brakes while driving slowly

to see if they have been affected

by water. If braking performance

is impaired, dry the brakes by

applying them lightly while

maintaining a slow forward

speed.

• Do not use any cleaners con-

taining acid or alkaline deter-

gents.

7

7-83

Maintenance

High-corrosion areas

High temperatures can also acceler- • When cleaning underneath the

ate corrosion of parts that are not

properly ventilated so the moisture

can be dispersed. For all these rea-

sons, it is particularly important to

keep your vehicle clean and free of

mud or accumulations of other mate-

rials. This applies not only to the vis-

ible surfaces but particularly to the

underside of the vehicle.

vehicle, pay particular attention to

the components under the fenders

and other areas that are hidden

from view. Do a thorough job; just

dampening the accumulated mud

rather than washing it away will

accelerate corrosion rather than

prevent it. Water under high pres-

sure and steam are particularly

effective in removing accumulated

mud and corrosive materials.

• When cleaning lower door panels,

rocker panels and frame members,

be sure that drain holes are kept

open so that moisture can escape

and not be trapped inside to accel-

erate corrosion.

If you live in an area where your vehi-

cle is regularly exposed to corrosive

materials, corrosion protection is

particularly important. Some of the

common causes of accelerated cor-

rosion are road salts, dust control

chemicals, ocean air and industrial

pollution.

Moisture breeds corrosion

Moisture creates the conditions in

which corrosion is most likely to

To help prevent corrosion

Keep your vehicle clean

occur. For example, corrosion is The best way to prevent corrosion is

accelerated by high humidity, partic- to keep your vehicle clean and free

ularly when temperatures are just of corrosive materials. Attention to

above freezing. In such conditions, the underside of the vehicle is partic-

the corrosive material is kept in con- ularly important.

tact with the car surfaces by moisture

that is slow to evaporate.

• If you live in a high-corrosion area

Mud is particularly corrosive

because it is slow to dry and holds

moisture in contact with the vehicle.

Although the mud appears to be dry,

it can still retain the moisture and

promote corrosion.

— where road salts are used, near

the ocean, areas with industrial

pollution, acid rain, etc.—, you

should take extra care to prevent

corrosion. In winter, hose off the

underside of your vehicle at least

once a month and be sure to clean

the underside thoroughly when

winter is over.

7-84

Keep your garage dry

Cleaning the upholstery and

interior trim

Vinyl (if equipped)

Remove dust and loose dirt from

vinyl with a whisk broom or vacuum

cleaner. Clean vinyl surfaces with a

vinyl cleaner.

Interior Care

Don't park your vehicle in a damp,

poorly ventilated garage. This cre-

ates a favorable environment for cor-

rosion. This is particularly true if you

wash your vehicle in the garage or

drive it into the garage when it is still

wet or covered with snow, ice or

mud. Even a heated garage can con-

tribute to corrosion unless it is well

ventilated so moisture is dispersed.

Interior general precautions

Prevent caustic solutions such as

perfume and cosmetic oil, from con-

tacting the interior parts because

they may cause damage or discol-

oration. If they do contact the interior

parts, wipe them off immediately.

See the instructions for the proper

way to clean vinyl.

Fabric (if equipped)

Remove dust and loose dirt from fab-

ric with a whisk broom or vacuum

cleaner. Clean with a mild soap solu-

tion recommended for upholstery or

carpets. Remove fresh spots imme-

diately with a fabric spot cleaner. If

fresh spots do not receive immediate

attention, the fabric can be stained

and its color can be affected. Also, its

fire-resistant properties can be

reduced if the material is not proper-

ly maintained.

NOTICE

Keep paint and trim in good condition

• Never allow water or other liq-

uids to come in contact with

electrical/electronic

nents inside the vehicle as this

may damage them.

• When cleaning leather products

(steering wheel, seats etc.), use

neutral detergents or low alco-

hol content solutions. If you use

high alcohol content solutions

or acid/ alkaline detergents, the

color of the leather may fade or

the surface may get stripped off.

Scratches or chips in the finish

should be covered with "touch-up"

paint as soon as possible to reduce

the possibility of corrosion. If bare

metal is showing through, the atten-

tion of a qualified body and paint

shop is recommended.

Bird droppings are highly corrosive

and may damage painted surfaces in

just a few hours. Always remove bird

droppings as soon as possible.

compo-

7

NOTICE

Using anything but recommended

cleaners and procedures may

affect the fabric's appearance and

fire-resistant properties.

7-85

Maintenance

Leather (if equipped)

• Caring for the leather seats

CAUTION

• Features of seat leather

- Vacuum the seat periodically to

remove dust and sand on the seat.

It will prevent abrasion or damage

of the leather and maintain its qual-

ity.

- Wipe the natural leather seat cover

often with dry or soft cloth.

- Use of proper leather protector

may prevent abrasion of the cover

and helps maintain the color. Be

sure to read the instructions and

consult a specialist when using

leather coating or protective agent.

- Light colored (beige, cream beige)

leather is easily contaminated and

the stain is noticeable. Clean the

seats frequently.

- Leather is made from the outer

skin of an animal, which goes

through a special process to be

available for use. Since it is a nat-

ural product, each part differs in

thickness or density.

Wrinkles may appear as a natural

result of stretching and shrinking

depending on the temperature

and humidity.

- The seat is made of stretchable

fabric to improve comfort.

- The parts contacting the body are

curved and the side supporting

area is high which provides driv-

ing comfort and stability.

• Wrinkles or abrasions which

appear naturally from usage

are not covered by warranty.

• Belts with metallic acces-

sories, zippers or keys inside

the back pocket may damage

the seat fabric.

• Make sure not to wet the seat.

It may change the nature of

natural leather.

• Jeans or clothes which could

bleach may contaminate the

surface of the seat covering

fabric.

- Avoid wiping with wet cloth. It may

cause the surface to crack.

- Wrinkles may appear naturally

from usage. It is not a fault of the

products.

7-86

• Cleaning the leather seats

Cleaning the seat belt webbing

- Remove all contaminations instant-

ly. Refer to instructions below for

removal of each contaminant.

- Cosmetic products (sunscreen,

foundation, etc.)

Apply cleansing cream on a cloth

and wipe the contaminated spot.

Wipe off the cream with a wet cloth

and remove water with a dry cloth.

Clean the belt webbing with any mild

soap solution recommended for

cleaning upholstery or carpet. Follow

the instructions provided with the

soap. Do not bleach or re-dye the

webbing because this may weaken

the seat belt.

Cleaning the interior window

glass

- Beverages (coffee, soft drink, etc.)

If the interior glass surfaces of the

vehicle become fogged (that is, cov-

ered with an oily, greasy or waxy

film), they should be cleaned with

glass cleaner. Follow the directions

on the glass cleaner container.

Apply a small amount of neutral

detergent and wipe until contami-

nations do not smear.

- Oil

Remove

oil

instantly

with

absorbable cloth and wipe with

stain remover used only for natural

leather.

NOTICE

7

Do not scrape or scratch the

inside of the rear window. This

may result in damage to the rear

window defroster grid.

- Chewing gum

Harden the gum with ice and

remove gradually.

7-87

Maintenance

EMISSION CONTROL SYSTEM

The emission control system of your

vehicle is covered by a written limited

warranty. Please see the warranty

information contained in the Owner’s

Handbook & Warranty Information

booklet in your vehicle.

1. Crankcase Emission Control

System

NOTICE

For

the

Inspection

and

The positive crankcase ventilation

system is employed to prevent air

pollution caused by blow-by gases

being emitted from the crankcase.

This system supplies fresh filtered air

to the crankcase through the air

intake hose. Inside the crankcase,

the fresh air mixes with blow-by

gases, which then pass through the

PCV valve into the induction system.

Maintenance Test (with Electronic

Stability Control (ESC) system)

• To prevent the vehicle from mis-

firing during dynamometer test-

ing, turn the Electronic Stability

Control (ESC) system off by

pressing the ESC switch (ESC

OFF light illuminated).

• After dynamometer testing is

completed, turn the ESC system

back on by pressing the ESC

switch again.

Your vehicle is equipped with an

emission control system to meet all

applicable emission regulations.

There are three emission control

systems, as follows.

(1) Crankcase emission control sys-

tem

(2) Evaporative emission control sys-

tem

2. Evaporative Emission Control

System Including Onboard

Refueling Vapor Recovery

(ORVR)

(3) Exhaust emission control system

The Evaporative Emission Control

System is designed to prevent fuel

vapors from escaping into the atmos-

phere. The ORVR system is

designed to allow the vapors from

the fuel tank to be loaded into a can-

ister while refueling at the gas sta-

tion, preventing the escape of fuel

vapors into the atmosphere.

In order to ensure the proper func-

tion of the emission control systems,

it is recommended that you have

your vehicle inspected and main-

tained by an authorized HYUNDAI

dealer in accordance with the main-

tenance schedule in this manual.

7-88

Canister

Engine exhaust (carbon monox-

ide) precautions

3. Exhaust Emission Control

System

The Exhaust Emission Control

System is a highly effective system

which controls exhaust emissions

while maintaining good vehicle per-

formance.

When the engine starts or fails to

start, excessive attempts to restart

the engine may cause damage to the

emission system.

Fuel vapors generated inside the fuel

tank are absorbed and stored in the

onboard canister.When the engine is

running, the fuel vapors absorbed in

the canister are drawn into the surge

tank through the purge control sole-

noid valve.

• Carbon monoxide can be present

with other exhaust fumes. If you

smell exhaust fumes of any kind in

your vehicle, drive with all the win-

dows fully open. Have your vehicle

checked and repaired immediately.

WARNING

Purge Control Solenoid Valve

(PCSV)

Engine exhaust gases contain

carbon monoxide (CO). Though

colorless and odorless, it is

dangerous and could be lethal if

inhaled. Follow the instructions

on this page to avoid CO poi-

soning.

The purge control solenoid valve is

controlled by the Engine Control

Module (ECM); when the engine

coolant temperature is low during

idling, the PCSV closes so that evap-

orated fuel is not taken into the

engine. After the engine warms-up

during ordinary driving, the PCSV

opens to introduce evaporated fuel to

the engine.

7

7-89

Maintenance

• Do not operate the engine in con-

fined or closed areas (such as

garages) any more than what is

necessary to move the vehicle in or

out of the area.

Operating precautions for cat-

alytic converters (if equipped)

WARNING

CALIFORNIA PROPOSITION 65

WARNING

Engine exhaust and a wide vari-

ety of automobile components

and parts, including compo-

nents found in the interior fur-

nishings in a vehicle, contain or

emit chemicals known to the

State of California to cause can-

cer and birth defects and repro-

ductive harm. In addition, cer-

tain fluids contained in vehicles

and certain products of compo-

nent wear contain or emit chem-

icals known to the State of

California to cause cancer and

birth defects or other reproduc-

tive harm.

• When the vehicle is stopped in an

open area for more than a short

time with the engine running,

adjust the ventilation system (as

needed) to draw outside air into the

vehicle.

• Never sit in a parked or stopped

vehicle for any extended time with

the engine running.

• When the engine stalls or fails to

start, excessive attempts to restart

the engine may cause damage to

the emission control system.

The exhaust system and cat-

alytic converter are very hot

during and immediately after

the engine has been running.To

avoid SERIOUS INJURY or

DEATH:

• Do not park, idle, or drive the

vehicle over or near flamma-

ble objects, such as grass,

vegetation, paper, leaves, etc.

A hot exhaust system can

ignite flammable items under

your vehicle.

• Keep away from the exhaust

system and catalytic convert-

er or you may get burned.

Also, Do not remove the heat

sink around the exhaust sys-

tem, do not seal the bottom of

the vehicle, and do not coat

the vehicle for corrosion con-

trol. It may present a fire risk

under certain conditions.

7-90

Your vehicle is equipped with a cat- • Do not modify or tamper with any

alytic converter emission control

device.

To prevent damage to the catalytic

converter and to your vehicle, take

the following precautions:

• Use only UNLEADED FUEL for

gasoline engines.

• Do not operate the vehicle when

there are signs of engine malfunc-

tion, such as misfire or a noticeable

loss of performance.

part of the engine or emission con-

trol system. All inspections and

adjustments must be made by an

authorized HYUNDAI dealer.

• Avoid driving with extremely low

fuel level. If you run out of gasoline,

it could cause the engine to misfire

and result in excessive loading of

the catalytic converter.

• Do not misuse or abuse the

engine. Examples of misuse are

coasting with the engine off and

descending steep grades in gear

with the engine off.

• Do not operate the engine at high

idle speed for extended periods (5

minutes or more).

7

7-91

Maintenance

CALIFORNIA PERCHLORATE NOTICE

Perchlorate Material-special handling may apply, See: www.dtsc.ca.gov/hazardouswaste/perchlorate.

Notice to California Vehicle Dismantlers:

Perchlorate containing materials, such as air bag inflators, seatbelt pretensioners and keyless remote entry batteries,

must be disposed of according to Title 22 California Code of Regulations Section 67384.10 (a).

7-92

Maintenance for Your Hyundai Kona SUV 2020

Popular Manuals