Get Maintenance -> Light bulbs Guide for Hyundai Kona SUV 2020

LIGHT BULBS

Consult an authorized HYUNDAI

dealer to replace most vehicle light

bulbs. It is difficult to replace vehicle

light bulbs because other parts of the

vehicle must be removed before you

can get to the bulb. This is especially

true for removing the headlamp

assembly to get to the bulb(s).

Headlamp, Position lamp,

Daytime Running Light, Turn

signal lamp, Cornering lamp

and Side marker

WARNING

• Prior to replacing a lamp,

depress the foot brake, move

the shift lever into P (Park)

apply the parking brake, place

the ignition switch to the

LOCK/OFF position, and take

the key with you when leaving

the vehicle to avoid sudden

movement of the vehicle and

to prevent possible electric

shock.

Type A

Removing/installing the headlamp

assembly can result in damage to

the vehicle.

i

Information

• Be aware the bulbs may be

hot and may burn your fin-

gers.

The headlamp and tail lamp lenses

could appear frosty if the vehicle is

washed after driving or the vehicle is

driven at night in wet weather. This

condition is caused by temperature

difference between the lamp inside

and outside and, it does not indicate a

problem with your vehicle. When

moisture condenses in the lamp, it will

be removed after driving with the

headlamp on. The removable level

may differ depending on lamp size,

lamp position and environmental con-

dition. However, if moisture is not

removed, we recommend that your

vehicle is inspected by an authorized

HYUNDAI dealer.

OOS077033N

(1) Headlamp (Low)

(2) Headlamp (High)

(3) Daytime running light (if equipped)

/Position lamp

7

(4) Turn signal lamp

(5) Front fog lamp (if equipped)

(6) Side marker

(7) Side reflex reflector

7-69

Maintenance

■ High/Low beam

• Always handle them carefully, and

avoid scratches and abrasions. If

the bulbs are lit, avoid contact with

liquids.

WARNING

• Never touch the glass with bare

hands. Residual oil may cause the

bulb to overheat and burst when lit.

• A bulb should be operated only

when installed in a headlamp.

• If a bulb becomes damaged or

cracked, replace it immediately

and carefully dispose of it.

OOS077034

OLMB073042L

[1] : High beam, [2] : Low beam

• Handle halogen bulbs with

care. Halogen bulbs contain

pressurized gas that will pro-

duce flying pieces of glass that

could cause injuries if broken.

• Wear eye protection when

changing a bulb. Allow the

bulb to cool down before han-

dling it.

1. Open the hood.

2. Disconnect the negative battery

cable.

3. Remove the headlamp bulb cover

by turning it counterclockwise.

4. Disconnect the headlamp bulb

socket-connector.

7-70

5. Remove the bulb from the head-

lamp assembly.

6. Install a new headlamp bulb and

snap the headlamp bulb retaining

wire into position by aligning the

wire with the groove on the bulb.

5. Install a new bulb by inserting it

into the socket and rotating it until

it locks into place.

6. Install the socket in the assembly

by aligning the tabs on the socket

with the slots in the assembly.

7. Connect the headlamp bulb sock-

et-connector.

7. Push the socket into the assembly

and turn the socket clockwise.

8. Install the headlamp bulb cover by

turning it clockwise.

Position lamp and daytime running

light

OOS077038

i

Information

Your vehicle is equipped with LED

lamps. LED lamps do not have

replaceable bulbs. If the LED lamp

does not operate, have the vehicle

checked by an authorized HYUNDAI

dealer.

Turn signal

The headlamp aiming should be

adjusted after an accident or after the

headlamp assembly is reinstalled at an

authorized HYUNDAI dealer.

1. Open the hood.

2. Disconnect the negative battery

cable.

3. Remove the socket (1) from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

4. Remove the bulb from the socket

by pressing it in and rotating it

counterclockwise until the tabs on

the bulb align with the slots in the

socket. Pull the bulb out of the

socket.

Side marker

If the light bulb does not operate,

have the vehicle checked by an

authorized HYUNDAI dealer.

7

7-71

Maintenance

• Always handle them carefully, and

avoid scratches and abrasions. If

the bulbs are lit, avoid contact with

liquids.

Type B

WARNING

• Never touch the glass with bare

hands. Residual oil may cause the

bulb to overheat and burst when lit.

• A bulb should be operated only

when installed in a headlamp.

• If a bulb becomes damaged or

cracked, replace it immediately

and carefully dispose of it.

OLMB073042L

OOS078052N

• Handle halogen bulbs with

care. Halogen bulbs contain

pressurized gas that will pro-

duce flying pieces of glass that

could cause injuries if broken.

• Wear eye protection when

changing a bulb. Allow the

bulb to cool down before han-

dling it.

(1) Headlamp (Low/High)

(2) Cornering light

(3) Daytime running light (if equipped)

/Position lamp

(4) Turn signal lamp

(5) Front fog lamp (if equipped)

(6) Side marker

Headlamp

Your vehicle is equipped with LED

lamps. LED lamps do not have

replaceable bulbs. If the LED lamp

does not operate, have the vehicle

checked by an authorized HYUNDAI

dealer.

(7) Side reflex reflector

7-72

5. Insert a new bulb by inserting it

into the socket and rotating it until

it locks into place.

6. Install the socket in the assembly

by aligning the tabs on the socket

with the slots in the assembly.

7. Push the socket into the assembly

and turn the socket clockwise.

OOS077037

OOS077038

Cornering Lamp

1. Open the hood.

Turn signal

1. Open the hood.

2. Disconnect the negative battery

cable.

2. Disconnect the negative battery

cable.

3. Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

3. Remove the socket (1) from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

7

4. Remove the bulb from the socket

by pressing it in and rotating it

counterclockwise until the tabs on

the bulb align with the slots in the

socket.

4. Remove the bulb from the socket

by pressing it in and rotating it

counterclockwise until the tabs on

the bulb align with the slots in the

socket. Pull the bulb out of the

socket.

Pull the bulb out of the socket.

7-73

Maintenance

5. Install a new bulb by inserting it

into the socket and rotating it until

it locks into place.

6. Install the socket in the assembly

by aligning the tabs on the socket

with the slots in the assembly.

5. Install a new bulb-socket into the

housing by aligning the tabs on the

socket with the slots in the housing.

Push the socket into the housing

and turn the socket clockwise.

Front fog lamp (if equipped)

7. Push the socket into the assembly

and turn the socket clockwise.

Side Repeater Lamp

Replacement

Position lamp and daytime running

light

Your vehicle is equipped with LED

lamps. LED lamps do not have

replaceable bulbs. If the LED lamp

does not operate, have the vehicle

checked by an authorized HYUNDAI

dealer.

OOS077059L

1. Loosen the pin-type retainers of the

under cover and then remove the

undercover.

2. Reach your hand into the back of the

front bumper.

Side marker

If the light bulb does not operate,

have the vehicle checked by an

authorized HYUNDAI dealer.

3. Disconnect the power connector

from the socket.

4. Remove the bulb-socket from the

housing by turning the socket coun-

terclockwise until the tabs on the

socket align with the slots of the

housing.

OOS077039

If the light bulb does not operate,

have the vehicle checked by an

authorized HYUNDAI dealer.

7-74

(3) Turn signal lamp

(4) Backup lamp

(5) Side marker

Rear Combination Light Bulb

Replacement

■ Type A (Standard)

OOS077066L

Stop/Tail lamp

1. Open the liftgate.

OOS077040N

■ Type B (LED)

2. Open the lamp assembly retaining

screw covers.

3. Loosen the lamp assembly retain-

ing screws with a cross-tip screw-

driver.

7

OOS078041N

(1) Stop/Tail lamp

(2) Tail lamp (Type A),

Stop/Tail lamp (Type B)

7-75

Maintenance

8. Install the socket into the assem- 4. Remove the socket from the

bly by aligning the tabs on the

socket with the slots in the assem-

bly. Push the socket into the

assembly and turn the socket

clockwise.

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

5. Remove the bulb from the socket

by pressing it in and rotating it

counterclockwise until the tabs on

the bulb align with the slots in the

socket. Pull the bulb out of the

socket.

9. Reinstall the lamp assembly to the

body of the vehicle.

OOS077068L

6. Insert a new bulb by inserting it

into the socket and rotating it until

it locks into place.

7. Install the socket into the assem-

bly by aligning the tabs on the

socket with the slots in the assem-

bly. Push the socket into the

assembly and turn the socket

clockwise.

4. Remove the rear combination

lamp assembly from the body of

the vehicle.

5. Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

6. Remove the bulb from the socket

by pressing it in and rotating it

counterclockwise until the tabs on

the bulb align with the slots in the

socket. Pull the bulb out of the

socket.

OOS077069L

Tail lamp (Type A)

8. Reinstall the lamp assembly to the

body of the vehicle.

1. Turn off the engine.

2. Open the tailgate.

3. Remove the service cover using a

flat-blade screwdriver.

7. Insert a new bulb by inserting it

into the socket and rotating it until

it locks into place.

7-76

Tail / Stop lamp (Type B)

7. Remove the high mounted stop

lamp after removing the mounting

nuts.

High Mounted Stop Lamp

Replacement

Your vehicle is equipped with LED

lamps. LED lamps do not have

replaceable bulbs. If the LED lamp

does not operate, have the vehicle

checked by an authorized HYUNDAi

dealer.

8. Install a new lamp

9. Reinstall the rear spoiler and the

liftgate upper trim in the reverse

order.

Turn signal lamp / Back up lamp

If the light bulb does not operate,

have the vehicle checked by an

authorized HYUNDAI dealer.

OOS077042

Side marker

1. Open the liftgate.

Your vehicle is equipped with LED

lamps. LED lamps do not have

replaceable bulbs. If the LED lamp

does not operate, have the vehicle

checked by an authorized HYUNDAI

dealer.

2. Gently remove the cover of the lift-

gate trim.

3. Remove the spoiler plug hole.

4. Disconnect the connector and

remove the washer hose and the

plug holes.

7

5. Remove the mounting nuts.

6. Remove the rear spoiler assembly.

7-77

Maintenance

License Plate Light Bulb

Replacement

Interior Light Bulb Replacement

Map lamp, Room lamp, Vanity mirror lamp, Luggage compartment

lamp and Glove box lamp

■ Map lamp (Type A)

■ Room lamp (Type A)

OOS077043

OOS077053

OOS077054

1. Using a flat-blade screwdriver,

gently pry the lens cover from the

lamp housing.

■ Map lamp (Type B)

■ Room lamp (Type B)

2. Remove the bulb by pulling it

straight out.

3. Install a new bulb.

4. Reinstall in the reverse order.

OOS077044

OOS077045

7-78

■ Vanity mirror lamp

■ Glove box lamp

3. Install a new bulb in the socket.

4. Align the lens tabs with the interi-

or lamp housing notches and snap

the lens into place.

NOTICE

Use care not to dirty or damage

lens, lens tab, and plastic hous-

ings.

OOS077046

OOS077047

■ Luggage compartment lamp

1. Using a flat-blade screwdriver,

gently pry the lens from the interi-

or lamp housing.

2. Remove the bulb by pulling it

straight out.

WARNING

7

Prior to working on the Interior

Lights, ensure that the "OFF"

button is depressed to avoid

burning your fingers or receiv-

ing an electric shock.

OOS077048

7-79

Maintenance

APPEARANCE CARE

Exterior Care

Protecting your vehicle's finish

Washing

WARNING

Exterior general caution

To help protect your vehicle’s finish

from rust and deterioration, wash it

thoroughly and frequently at least

once a month with lukewarm or cold

water.

If you use your vehicle for off-road

driving, you should wash it after each

off-road trip. Pay special attention to

the removal of any accumulation of

salt, dirt, mud, and other foreign

materials. Make sure the drain holes

in the lower edges of the doors and

rocker panels are kept clear and

clean.

Insects, tar, tree sap, bird droppings,

industrial pollution and similar

deposits can damage your vehicle’s

finish if not removed immediately.

Even prompt washing with plain

water may not completely remove all

these deposits. A mild soap, safe for

use on painted surfaces, should be

used.

After washing the vehicle, test

the brakes while driving slowly

to see if they have been affected

by water before getting on the

road. If braking performance is

impaired, dry the brakes by

applying them lightly while

maintaining a slow forward

speed.

It is very important to follow the label

directions when using any chemical

cleaner or polish. Read all warning

and caution statements that appear

on the label.

High-pressure washing

• When using high-pressure wash-

ers, make sure to maintain suffi-

cient distance from the vehicle.

Insufficient clearance or excessive

pressure can lead to component

damage or water penetration.

• Do not spray the camera, sensors

or its surrounding area directly with

a high pressure washer. Shock

applied from high pressure water

may cause the device to not oper-

ate normally.

• Do not bring the nozzle tip close to

boots (rubber or plastic covers)or

connectors as they may be dam-

aged if they come into contact with

high pressure water.

• Do not use any high-pressure noz-

zles, which induce either one-direct

water stream or water swirling.

NOTICE

• Do not use strong soap, chemi-

cal detergents or hot water, and

do not wash the vehicle in direct

sunlight or when the body of the

vehicle is warm.

• Be careful when washing the

side windows of your vehicle.

Especially, with high-pressure

water, water may leak through

the windows and wet the interi-

or.

• To prevent damage to the plastic

parts, do not clean with chemi-

cal solvents or strong deter-

gents.

After washing, rinse the vehicle thor-

oughly with lukewarm or cold water.

Do not allow soap to dry on the fin-

ish.

7-80

Maintenance -> Light bulbs for Your Hyundai Kona SUV 2020

Popular Manuals