Convenience features for Your Hyundai Santa Fe SUV 2023

05  
ACCESSING YOUR VEHICLE  
Remote key (if equipped)  
WARNING  
Do not leave the keys in your  
vehicle with unsupervised children.  
Unattended children could place the  
key in the ignition switch and may  
operate power windows or other  
controls, or even make the vehicle  
move, which could result in serious  
injury or death.  
Unlocking  
To unlock:  
OPD046001  
1. Press the Door Unlock button (2) on  
the remote key.  
Your HYUNDAI uses a remote key, which  
you can use to lock or unlock the driver  
and passenger doors or the liftgate.  
1. Door Lock  
2. Door Unlock  
3. Liftgate Open  
4. Panic  
2. The doors will unlock. The hazard  
warning lights will blink two times.  
Also, the side view mirror will unfold,  
LIꢀœ&RQYHQLHQFHꢀƟꢀ:HOFRPHꢀPLUURUꢁ  
OLJKWꢀƟꢀ2QꢀGRRUꢀXQORFNŔꢀLVꢀVHOHFWHGꢀ  
from the User Settings mode on the  
LCD display. For more details, refer to  
“LCD Display” in chapter 4.  
Locking  
To lock :  
Information  
After unlocking the doors, the doors will  
lock automatically after 30 seconds unless  
a door is opened.  
1. Close all doors, engine hood and  
liftgate.  
2. Press the Door Lock button (1) on the  
remote key.  
3. The doors will lock. The hazard  
warning lights will blink. Also, the side  
view mirror will fold, if ‘Convenience  
Ɵꢀ:HOFRPHꢀPLUURUꢁOLJKWꢀƟꢀ2QꢀGRRUꢀ  
unlock’ is selected from the User  
Settings mode on the LCD display. For  
more details, refer to “LCD Display”  
in chapter 4.  
Panic alarm  
The horn sounds and the hazard warning  
lights blink for about 30 seconds if this  
button is pressed for more than 0.5  
seconds. To stop the horn and lights,  
press any button on the transmitter.  
4. Make sure the doors are locked by  
checking the position of the door lock  
button inside the vehicle.  
5-5  
Convenience features  
Mechanical key  
Information  
The word “HOLD” is written on the  
button to inform you that you must press  
and hold the button for more than one  
second.  
Start-up  
For detailed information refer to “Key  
Ignition Switch” in chapter 6.  
NOTICE  
OPD046003  
To prevent damaging the remote key:  
If the remote key does not operate  
normally, you can lock or unlock the door  
by using the mechanical key.  
To unfold the key, press the release  
button then the key will unfold  
automatically.  
śꢀ Keep the remote key away from  
water or any liquid and fire. If  
the inside of the remote key gets  
damp (due to drinks or moisture),  
or is heated, internal circuit may  
malfunction, excluding the car from  
the warranty.  
To fold the key, fold the key manually  
while pressing the release button.  
śꢀ Avoid dropping or throwing the  
remote key.  
NOTICE  
śꢀ Protect the remote key from extreme  
temperatures.  
Do not fold the key without pressing the  
release button. This may damage the  
key.  
Remote key precautions  
The remote key will not work if any of the  
following occur:  
śꢀ The key is in the ignition switch.  
śꢀ You exceed the operating distance  
limit (about 10 m [30 feet]).  
śꢀ The remote key battery is weak.  
śꢀ Other vehicles or objects may be  
blocking the signal.  
śꢀ The weather is extremely cold.  
śꢀ The remote key is close to a radio  
transmitter such as a radio station or  
an airport which can interfere with  
normal operation of the remote key.  
5-6  
05  
When the remote key does not work  
correctly, open and close the door  
with the mechanical key. If you have  
a problem with the remote key, it is  
recommended that you contact an  
authorized HYUNDAI dealer.  
Battery replacement  
If the remote key is in close proximity to  
your mobile phone, the signal could be  
blocked by your mobile phone’s normal  
operational signals.  
This is especially important when the  
phone is active such as making and  
receiving calls, text messaging, and/ or  
sending/receiving emails.  
OPD046002  
Avoid placing the remote key and your  
mobile phone in the same location and  
always try to maintain an adequate  
distance between the two devices.  
Battery Type: CR2032  
1. Insert a slim tool into the slot and  
gently pry open the cover.  
2. Remove the old battery and insert the  
new battery. Make sure the battery  
position is correct.  
3. Reinstall the rear cover of the remote  
key.  
If you suspect your remote key might  
have sustained some damage, or you feel  
your remote key is not working correctly,  
it is recommended that you contact an  
authorized HYUNDAI dealer.  
Information  
This device complies with Part 15 of the  
FCC rules.  
Operation is subject to the following three  
conditions:  
1. This device may not cause harmful  
interference.  
2. This device must accept any  
interference received, including  
interference that may cause undesired  
operation.  
3. Changes or modifications not expressly  
approved by the party responsible  
for compliance could void the user’s  
authority to operate the device.  
WARNING  
THIS PRODUCT CONTAINS A BUTTON  
BATTERY.  
If swallowed, a lithium button battery  
can cause severe or fatal injuries within  
2 hours. Keep batteries out of reach of  
children.  
If you think batteries may have been  
swallowed or placed inside any part  
of the body, seek immediate medical  
attention.  
NOTICE  
Keep the remote key away from  
electromagnetic materials that block  
electromagnetic waves to the key  
surface.  
5-7  
Convenience features  
„Type C  
Information  
An inappropriately disposed  
battery can be harmful to  
the environment and human  
health. Dispose of the battery  
according to your local law(s)  
and regulation.  
Smart key (if equipped)  
„Type A  
OTMA050022  
„Type D  
OTM050003  
„Type B  
OTMA050021  
1. Door lock  
2. Door unlock  
3. Panic  
4. Remote Smart Parking Assist  
(Forward)  
5. Remote Smart Parking Assist  
(Rearward)  
6. Remote start  
OTM050004  
Your HYUNDAI uses a smart key, which  
you can use to lock or unlock a door (and  
liftgate) and even start the engine even  
just carrying the key.  
1. Door lock  
2. Door unlock  
3. Liftgate Open (Liftgate)  
Liftgate Open / Close (Power liftgate)  
4. Panic Open / Close  
5. Remote Smart parking Assist  
(Forward)  
6. Remote Smart parking Assist  
(Rearward)  
7. Remote start  
5-8  
05  
Locking your vehicle (Button type)  
Locking your vehicle (Touch sensor  
type)  
OTM048000  
OTMA050001  
To lock :  
1. Close all of the doors, the hood and  
the liftgate.  
1. Close all doors, engine hood and  
liftgate.  
2. Make sure you have the smart key in  
your possession and touch either the  
touch sensor on the door handle (the  
engraved part) or press the Door Lock  
button (1) on the smart key within 1  
second.  
2. Carry the smart key.  
3. Either press the door handle button or  
press the Door Lock button (1) on the  
smart key.  
4. The hazard warning lights will blink.  
Also, the side view mirror will fold,  
LIꢀœ&RQYHQLHQFHꢀƟꢀ:HOFRPHꢀPLUURUꢁ  
OLJKWꢀƟꢀ2QꢀGRRUꢀXQORFNꢀRUꢀ2QꢀGULYHUꢀ  
approach’ is selected from the User  
Settings mode on the LCD display. For  
more details, refer to “LCD Display”  
in chapter 4.  
3. The doors, hood and trunk are locked.  
The chime will sound once and the  
hazard warning lights will blink.  
śꢀ The door handle button will only  
operate when the smart key is within  
28~40 inches (0.7~1 m) from the  
outside door handle.  
5. Make sure the doors are locked by  
checking the position of the door lock  
button inside the vehicle.  
śꢀ Make sure the doors are locked by  
pulling the door handle.  
śꢀ If you locked the door with the touch  
sensor on the door handle, the doors  
cannot be unlocked with the sensor  
within 3 seconds.  
5-9  
Convenience features  
Even though you press the outside  
door handle button, the doors will not  
lock and the chime will sound for three  
seconds if any of the following occur:  
Unlocking your vehicle  
„Button type  
śꢀ The Smart Key is in the vehicle.  
śꢀ The Engine Start/Stop button is in  
ACC or ON position.  
śꢀ Any door except the liftgate is open.  
CAUTION  
When you leave your vehicle with  
the smart key, make sure to press the  
button on the front door handle or  
touch the touch sensor on the front  
door handle to lock the doors after  
close all of the doors, the hood and the  
trunk. If you do not press the button  
or touch the touch sensor firmly, the  
doors might not be locked so please use  
caution.  
OTM048000  
„Touch sensor type  
WARNING  
OTM050005  
Do not leave the Smart Key in your  
vehicle with unsupervised children.  
Unattended children could press the  
Engine Start/ Stop button and may  
operate power windows or other  
controls, or even make the vehicle  
move, which could result in serious  
injury or death.  
1. Make sure you have the smart key in  
your possession.  
2. Press the Door Unlock button (2) on  
the smart key, press the button on the  
front door handle or touch the door  
unlock sensor inside of the front door  
handle to unlock the doors.  
3. All of the doors will unlock. When the  
doors unlock, the hazard warning  
lights will blink two times and the  
chime will sound.  
śꢀThe door handle button will only  
operate when the smart key is  
within 28~40 inches (0.7~1 m) from  
the outside door handle.  
śꢀIf you do not open the door after  
unlocking within 30 seconds, it will  
return to the lock mode.  
śꢀIf you unlocked the door with the  
door handle, the doors cannot be  
locked with the sensor within 2  
seconds.  
5-10  
05  
Opening the liftgate  
To open the liftgate:  
Remotely moving vehicle forward or  
reverse (if equipped)  
With the smart key, the driver can move  
the vehicle forward or reverse using the  
Forward or Reverse button on the smart  
key.  
For more details, refer to “Remote  
Smart Parking Assist (RSPA)” section in  
chapter 7.  
1. Make sure you have the smart key in  
your possession.  
2. Press either the liftgate open/close  
button on the vehicle or press and  
hold the liftgate open button on the  
smart key for more than one second.  
The hazard warning lights will blink  
two times and the liftgate will open.  
Panic alarm  
Remotely starting vehicle  
(if equipped)  
You can start the vehicle using the  
Remote Start button on the smart key.  
The horn sounds and the hazard warning  
lights blink for about 30 seconds if this  
button is pressed for more than 0.5  
seconds. To stop the horn and lights,  
press any button on the transmitter.  
To start the vehicle remotely:  
1. Press the door lock button on the  
smart key within 32 feet (10 m) from  
the vehicle.  
2. Press the Remote Start button for  
more than 2 seconds within 4 seconds  
after pressing the door lock button.  
Start-up  
You can start the vehicle without  
inserting the key.  
For more details, refer to the “Engine  
Start/Stop Button” section in chapter 6.  
3. The hazard warning lights will blink  
and the engine will start.  
4. To turn off the remote start function,  
press the Remote Start button once.  
Information  
If the smart key is not moved for some  
time, the detection function for smart key  
operation will pause. Lift the smart key to  
activate the detection again.  
Information  
śꢀ The vehicle must be in P (Park) for the  
NOTICE  
To prevent damaging the smart key:  
remote start function to start.  
śꢀ The engine turns off if you get on the  
śꢀ Keep the smart key in a cool,  
dry place to avoid damage or  
malfunction. Exposure to moisture  
or high temperature may cause  
the internal circuit of the smart key  
to malfunction which may not be  
covered under warranty.  
vehicle without a registered smart key.  
śꢀ The engine turns off if you do not get  
on the vehicle within 10 minutes after  
remotely starting the vehicle.  
śꢀ The Remote Start button may not  
operate if the smart key is not within 32  
feet (10 m).  
śꢀ Avoid dropping or throwing the  
śꢀ The vehicle will not remotely start if the  
smart key.  
engine hood or liftgate is opened.  
śꢀ Protect the smart key from extreme  
śꢀ Do not idle the engine for a long period.  
temperatures.  
5-11  
Convenience features  
Mechanical key  
Loss of a smart key  
If the Smart Key does not operate  
normally, you can lock or unlock the  
driver’s door by using the mechanical  
key.  
To remove the mechanical key from the  
smart key FOB:  
A maximum of two smart keys can  
be registered to a single vehicle. If  
you happen to lose your smart key,  
it is recommended that you should  
immediately take the vehicle and  
remaining key to your authorized  
HYUNDAI dealer or tow the vehicle, if  
necessary.  
Smart key precautions  
The smart key may not work if any of the  
following occur:  
śꢀ The smart key is close to a radio  
transmitter such as a radio station or  
an airport which can interfere with  
normal operation of the transmitter.  
śꢀ The smart key is near a mobile two  
OFE048007  
way radio system or a mobile phone.  
Press and hold the release button (1) and  
remove the mechanical key (2). Insert the  
mechanical key into the key hole on the  
door.  
To reinstall the mechanical key, put the  
key into the hole and push it until a click  
sound is heard.  
śꢀ Another vehicle’s smart key is being  
operated close to your vehicle.  
If the smart key does not work correctly,  
open and close the door with the  
mechanical key. If you have a problem  
with the smart key, it is recommended to  
contact an authorized HYUNDAI dealer.  
If the smart key is in close proximity to  
your mobile phone, the signal could be  
blocked by your mobile phone’s normal  
operational signals. This is specifically  
relevant when the phone is active such  
as making and receiving calls, text  
messaging, and/or sending/receiving  
emails. When possible, avoid keeping the  
smart key and your mobile phone in the  
same location such as a pants or jacket  
pocket in order to avoid interference  
between the two devices.  
5-12  
05  
Battery replacement  
If the Smart Key is not working properly,  
try replacing the battery with a new one.  
Battery Type: CR2032  
To replace the battery:  
Information  
This device complies with Part 15 of the  
FCC rules.  
Operation is subject to the following three  
conditions:  
1. This device may not cause harmful  
interference.  
2. This device must accept any  
interference received, including  
interference that may cause undesired  
operation.  
3. Changes or modifications not expressly  
approved by the party responsible  
for compliance could void the user’s  
authority to operate the device.  
ODN8059266  
NOTICE  
If the Smart Key is not working properly,  
try replacing the battery with a new one.  
Remove the smart key cover by turning  
the screwdriver clockwise by inserting  
the screwdriver (-) into the hole.  
śꢀ Keep the smart key away from  
electromagnetic materials that  
blocks electromagnetic waves to the  
key surface.  
śꢀ Always have the smart key with  
you when leaving the vehicle. If the  
smart key is left near the vehicle, the  
vehicle battery may be discharged.  
Battery Type: CR2032  
To replace the battery:  
1. Remove the mechanical key.  
2. Use a slim tool to pry open the rear  
cover of the smart key.  
3. Remove the old battery and insert the  
new battery. Make sure the battery  
position is correct.  
4. Reinstall the rear cover of the smart  
key.  
If you suspect your smart key might have  
sustained some damage, or you feel  
your smart key is not working correctly,  
it is recommended that you contact an  
authorized HYUNDAI dealer.  
5-13  
Convenience features  
Do not attempt to alter this system  
or add other devices to it. Electrical  
problems could result that may make  
your vehicle inoperable.  
WARNING  
THIS PRODUCT CONTAINS A BUTTON  
BATTERY.  
If swallowed, a lithium button battery  
can cause severe or fatal injuries within  
2 hours. Keep batteries out of reach of  
children.  
If you think batteries may have been  
swallowed or placed inside any part  
of the body, seek immediate medical  
attention.  
WARNING  
In order to prevent theft of your  
vehicle, do not leave spare keys  
anywhere in your vehicle. Your  
immobilizer password is a customer  
unique password and should be kept  
confidential.  
Information  
NOTICE  
An inappropriately disposed  
battery can be harmful to  
the environment and human  
health. Dispose of the battery  
according to your local law(s) or  
regulations.  
The transponder in your key is an  
important part of the immobilizer  
system. It is designed to give years  
of trouble-free service, however you  
should avoid exposure to moisture,  
static electricity and rough handling.  
Immobilizer system malfunction could  
occur.  
Immobilizer system  
The immobilizer system helps protect  
your vehicle from theft. If an improperly  
coded key (or other device) is used, the  
engine’s fuel system is disabled.  
When the Engine Start/Stop button  
is pressed to the ON position, the  
immobilizer system indicator should  
come on briefly, then go off. If the  
indicator starts to blink, the system does  
not recognize the coding of the key.  
Press the Engine Start/Stop button to  
the OFF position, then press the Engine  
Start/Stop button to the ON position  
again.  
The system may not recognize your  
key’s coding if another immobilizer  
key or other metal object (for example,  
key chain) is near the key. The engine  
may not start because the metal may  
interrupt the transponder signal from  
transmitting normally.  
Information  
This device complies with Part 15 of the  
FCC rules.  
Operation is subject to the following three  
conditions:  
1. This device may not cause harmful  
interference.  
2. This device must accept any  
interference received, including  
interference that may cause undesired  
operation.  
3. Changes or modifications not expressly  
approved by the party responsible  
for compliance could void the user’s  
authority to operate the device.  
If the system repeatedly does not  
recognize the coding of the key, it is  
recommended that you contact your  
HYUNDAI dealer.  
5-14  
05  
Digital key (smartphone) NFC  
function  
Hyundai Digital Key  
Digital Key Application  
You can use the Digital Key NFC (Near  
Field Communication) function after turn  
your smartphone NFC settings on. And  
you should unlock & turn on smartphone  
screen to use it.  
à To change the NFC mode of the  
smartphone, please refer to the  
smartphone manual or contact  
to the customer service center of  
smartphone manufacturers.  
To use Hyundai Digital Key mobile app,  
you should install Hyundai digital key  
application. Search ‘Hyundai digital key’  
in the Google Play Store and download  
the app. Please refer to the detailed  
manual of the digital key app. The option  
can be found under the following app  
menu:  
0HQXꢀƟꢀ$SSOLFDWLRQꢀ,QIRꢀƟꢀ7XWRULDO  
Please note the manual before using the  
app.  
à This service is only available for  
Android smartphones. Please confirm  
supported/compatible devices on our  
website.  
WARNING  
For used vehicle  
If any of the digital key (smartphone key  
or card key) is already registered when  
you press ON button after unlocking the  
doors, the message ‘Digital key(s) active’  
appears on the instrument cluster once.  
If you buy a used vehicle, you should  
confirm the message and delete the  
registered smartphone key and card key.  
In addition, please notify the Hyundai  
Customer Care Center.  
If the card key does not work properly,  
please delete the card key and register  
the smartphone key and re-register the  
card key.  
For vehicle maintenance  
If you need to have your Digital Key  
System repaired or replaced please  
ensure you Smartphone Key is still active.  
You may have to pair your phone again.  
In the case, re-initialize your Digital Keys  
using the Hyundai Digital Key mobile app.  
5-15  
Convenience features  
Digital key (smartphone)  
Information  
The [Save] button will be disabled if the  
digital key (Smartphone key) is already  
saved.  
Please refer to “Digital Key Delete” in this  
manual and follow the digital key delete  
procedure in your car before Digital key  
save.  
Please refer to the ‘Tutorial’ on your  
Digital key app and delete the previous  
saved key in your smartphone before save.  
ODN8A059129  
3. Select the vehicle to save on your  
Digital key application and activate  
the save mode.  
à Save mode is available only on  
the vehicle owner’s Digital key  
application.  
4. Place the backside of smartphone  
onto the wireless charging pad(in-  
vehicle authentication pad).  
The saving process will begin  
automatically.  
ODN8A059240  
5. Once the digital key save is complete,  
a message will be shown on the  
infotainment screen or cluster.  
6. Remove the smartphone from the pad  
and complete the saving process.  
Hyundai Digital Key (Smartphone)  
Pairing  
1. Turn the vehicle on with the Smart key  
and make sure to keep the smart key  
inside the vehicle during digital key  
registration.  
2. Register your Digital key from the  
vehicle user setting menu as follows.  
à With Navigation screen :  
From the infotainment screen menu,  
go to [Setup] - [Vehicle] - [Digital Key]  
- [Smart Phone Key] then select the  
[Save] from submenu.  
à Without navigation screen :  
From cluster menu, go to [Digital Key]  
- [Smart Phone Key] and select [Save].  
OTM050022  
[A] : Indicator light  
[B] : Wireless Charging Pad  
(In-vehicle Authentication Pad)  
5-16  
05  
3. Once the digital key delete is  
complete, a message will be shown  
on the infotainment screen or cluster.  
4. Go to [Initialize Digital Key] menu on  
the digital key application and select  
the vehicle to delete the digital key  
information.  
śꢀ 2SHQꢀWKHꢀ+\XQGDLꢀ'LJLWDOꢀ.H\ꢀDSSꢀƟꢀ  
0HQXꢀƟꢀ,QLWLDOL]Hꢀ'LJLWDOꢀ.H\  
à If the saved digital key information  
in your car is deleted due to vehicle  
maintenance, the digital key in your  
smartphone should be deleted as well.  
ODN8A059129  
à For more information, please refer to  
the ‘Tutorial’ on your Digital key app.  
CAUTION  
śꢀ If the smartphone is removed  
from the interior authentication  
pad during enrollment, the saving  
process will be cancelled.  
śꢀ If the infotainment or instrument  
cluster screen is changed during  
enrollment, the saving process will  
be cancelled.  
ODN8A059130  
Hyundai Digital Key (Smartphone Key)  
Deletion  
1. Turn the vehicle on with the Smart  
key and make sure to keep the smart  
key inside the vehicle during delete  
process.  
śꢀ If the vehicle is turned off during  
enrollment, the saving process will  
be cancelled.  
śꢀ If the gear is shifted, the saving  
2. Delete your Digital key from the  
vehicle user setting menu as follows.  
process will be cancelled.  
śꢀ If you try to save the smartphone  
which is not logged in with the  
vehicle owner’s ID or if you try to  
save the Card key, the saving process  
will not begin.  
à With Navigation screen :  
From the infotainment screen menu,  
go to [Setup] - [Vehicle] - [Digital Key]  
- [Smart Phone Key] then select the  
[Delete] from submenu.  
śꢀ If the NFC setting on your  
smartphone is off, the saving process  
will not begin.  
śꢀ If the smartphone screen is changed  
to off or locked status, the saving  
process will be cancelled.  
śꢀ If there is no Smart key during the  
save process, the saving process will  
not begin.  
à Without navigation screen :  
From cluster menu, go to [Digital  
Key] - [Smart Phone Key] and select  
[Delete].  
Information  
The [Delete] button will be disabled if there  
is no digital key (Smartphone key) saved.  
5-17  
Convenience features  
Set up main vehicle  
You can manage multiple digital keys  
from the Digital key app. From the list of  
digital keys you own, select the vehicle  
you want to make your priority vehicle.  
For more information, please refer to  
the ‘Tutorial’ on your Digital key app.  
OTMA050020  
[1] : Door handle authentication pad  
NFC door lock/unlock  
You should contact your smartphone’s  
NFC antenna(backside of phone) to door  
handle authentication pad (1) marked  
position near by the lock button) of  
driver’s (or front passenger’s) outside  
door for 2 seconds to lock or unlock the  
doors. If the Two Press Unlock feature  
is applied (press twice for unlocking),  
driver’s seat door will be unlocked by  
contacting the digital key (smartphone  
key). In this state, if you contact one  
more time within 4 seconds, all the doors  
unlock. Please make sure the doors are  
locked. If you do not open any of the  
doors after unlocking, it automatically  
re-lock after 30 seconds.  
Note that you cannot lock your vehicle  
when you contact NFC antenna in the  
smartphone to the door handle pad if  
any of the following occurs:  
śꢀ The Proximity / Smart Key is in the  
vehicle.  
śꢀ The Engine Start/Stop button is in  
ACC or ON position.  
śꢀ Any of the doors, hood and trunk is  
opened.  
If the smartphone digital key does not  
work, please remove the smartphone  
more than 4 inches (0.1 m) from the door  
handle authentication pad and try it  
again.  
5-18  
05  
After unlock the door or start up the  
vehicle with digital key, even though  
the driver tries to lock the doors by the  
central door lock switch, the door lock  
will be once locked and immediately  
released at the moment of door closed.  
The solution allows for offline mode usage  
when the mobile data connection of the  
smartphone is weak. When you are in the  
place where the mobile data connection  
of your smartphone is available and  
place your smartphone on the interior  
authentication pad (wireless charger) and  
start up your vehicle or contact the digital  
key on the door handle to lock or unlock  
the door, the remote renewal of security  
information starts automatically. Even  
though the engine is turned on, please  
wait until the remote renewal process  
is completed and wireless charger is  
converted to charging mode.  
Start-up with Digital Key  
1. After placing your registered  
smartphone onto the interior  
authentication pad (wireless charger),  
step on the brake and press the  
Engine Start/Stop button.  
2. After start-up, the digital key data  
will be automatically updated. It  
takes 5 to 20 seconds, after that,  
the smartphone can be go into the  
wireless charging mode automatically.  
Once the engine started, you can  
remove the smartphone from the pad.  
CAUTION  
The engine can be turned on if the  
registered smartphone or card key is  
placed on the interior authentication  
pad (wireless charger). Do not leave  
unsupervised children or people who  
are not aware of the system since it  
can result in serious injury or death.  
Always have the registered digital key  
(smartphone) or card key with you to  
prevent vehicle theft when leaving the  
vehicle.  
For more information, refer to the  
Engine Start/Stop button in chapter 6.  
OTM050022  
[A] : Indicator light  
[B] : Wireless Charging Pad  
(In-vehicle Authentication Pad)  
Information  
After reconnecting the vehicle battery  
power supply or charging the battery, it  
may take time to operate due to remote  
renewal of security information. When you  
lock or unlock the door with NFC, please  
contact and hold your smartphone on the  
door handle until it works.  
5-19  
Convenience features  
Remote Control with Digital Key  
To use the remote control function with  
your android smartphone, Bluetooth  
must be turned on.  
CAUTION  
śꢀ If metallic window tint was applied  
to your vehicle, it may cause  
bad Bluetooth connection or  
performance degradation of the  
digital key.  
śꢀ If multiple users operate the remote  
control function simultaneously, the  
connection between the digital key  
and the vehicle might result in failed  
commands. Please connect and  
operate the remote control function  
only the necessary user.  
śꢀ When using the remote control  
operation, the driver (the remote  
control user) should leave the vehicle  
after confirming the door lock (the  
chime sounds once and the hazard  
warning lights blink).  
śꢀ The remote functions of the Digital  
Key app enable the vehicle to be  
controlled from a set distance. If  
the digital key or the vehicle goes  
beyond the operable distance, the  
remote control function might be  
disconnected or cancelled.  
Remote Control Connection with Digital  
Key  
1. Open Hyundai digital key application  
on the smartphone. Select the  
vehicle to activate the remote control  
function as a main vehicle.  
2. Approach with the activated  
smartphone app to your vehicle  
and you can check whether the  
connection is available. If it enables  
your smartphone to connect, connect  
with your vehicle by pressing the  
connect button. The remote control  
function is activated after completing  
the process.  
Remote Control Operation with Digital  
Key  
You can execute the remote control  
operation including door lock/unlock,  
panic on/off, remote start / remote  
stop and trunk opening. The icon for  
each function will be highlighted and  
alarm/vibration also provided when the  
operation is performed.  
Note that you cannot lock your vehicle  
using the Hyundai digital key app if any  
of the following occurs:  
śꢀ If the digital key (smartphone) is  
connected with the vehicle for the  
remote control, the driver with the  
key goes far away from the vehicle,  
the function might not work.  
śꢀ If the remote control operation  
is executed where the mobile  
śꢀ The Engine Start/Stop button is in  
connection is weak, Bluetooth  
ACC or ON position.  
connection is poor due to several  
Bluetooth devices or there is an  
object such as metal or concrete, it  
might be delayed or the operable  
distance might decrease. You should  
not cover the smartphone with your  
hand or place other devices which  
can cause frequency interference. It  
may result in poor performance.  
śꢀ Any doors are open.  
When the smartphone and the vehicle  
are connected by the Bluetooth function  
but the remote control command  
cannot be received over 5 minutes, the  
remote control connection is cancelled  
automatically.  
śꢀ If the remote control function is not  
available, please use NFC function to  
lock or unlock the doors.  
5-20  
05  
Remote Start with Digital Key  
Smartphone change/App deletion  
śꢀ When the shift button of your vehicle  
is in P (Park) and all of the doors  
including trunk and hood is locked  
and the vehicle is off, press the Door  
Lock button in the Hyundai Digital  
Key app then press the Remote Start  
button within 4 seconds.  
If you change your smartphone or delete  
the Hyundai Digital Key App, please refer  
to the following to set up your Digital  
Key:  
Smartphone Change/ Reset  
If you change or reset the smartphone,  
the registered digital key in your previous  
smartphone may not be used. Please  
refer to following procedure to use the  
digital key.  
1. Install the digital key application and  
log in.  
2. If you are the owner, retry the Digital  
key save process.  
3. If you are the sharer, need to re-share  
the key from owner.  
You can confirm the engine is on if the  
hazard warning lights blinks two times  
and the chime sounds.  
śꢀ If you want to turn off the engine,  
press Remote Engine Stop. Air  
Conditioner / Heating system  
maintains the same status as when  
you last used the vehicle.  
śꢀ Unless you put the registered digital  
key(smartphone) on the interior  
authentication pad (wireless charger)  
when the remote start function is on,  
the engine will turn off.  
App delete & reinstall/ Delete App data  
śꢀ If you do not get on the vehicle within  
10 minutes after the engine turns on,  
the vehicle will turn off.  
You can re-download the digital key  
from server in these cases as follow  
procedure.  
For more information, refer to the Engine  
Start/Stop button in chapter 6.  
1. Reinstall the application and log in.  
2. Input the PIN number for user  
verification.  
3. If PIN is correct, digital key data  
will be re-downloaded to your  
smartphone and you can use it  
without any further registration or  
sharing.  
Vehicle information Display  
The digital key application displays  
the vehicle information such as  
driving or door conditions through the  
communication with the vehicle.  
śꢀ How to check : Select the vehicle  
what you want to check and touch  
the vehicle image, then vehicle  
information display page will be  
shown.  
śꢀ Contents : accumulated odometer,  
latest fuel economy, driving range,  
fuel remaining, tire pressure, doors  
lock/unlock status and last data  
updated time.  
Smartphone operability with Digital Key  
The digital key application may not  
be available to old type smartphones.  
Please check the available smartphone  
models with your dealer. NFC antenna  
position on the smartphone can be  
confirmed on each smartphone’s manual  
or contact to customer service center of  
the smartphone manufacture.  
à Displayed vehicle date could be  
differed from the current vehicle  
condition.  
à For more information, please refer to  
the ‘Tutorial’ on your Digital key app.  
5-21  
Convenience features  
śꢀ If the remote control function is not  
activated, please use NFC function to  
lock or unlock the doors  
śꢀ You should be careful not to  
press the remote control button  
on the digital key (smartphone)  
accidentally.  
śꢀ If the digital key (smartphone) is  
discharged or defective or you  
cannot use the digital key since the  
vehicle battery is discharged, use the  
inside door lock button to lock all of  
the doors.  
CAUTION  
śꢀ Do not leave the registered digital  
key (smartphone) and card key in  
your vehicle. Please carry around  
your keys all the times.  
śꢀ If you happen to lose your digital  
key (smartphone) or card key  
registered as a main user’s key, you  
should immediately delete the key  
on the vehicle’s key menu. For more  
information, refer to the Digital Key  
Deletion in this chapter.  
śꢀ If you registered your digital key  
(smartphone) or card key in the  
vehicle, a message appears on the  
instrument cluster and let you know  
the key is registered.  
CAUTION  
śꢀ Hyundai digital key app on the  
smartphone and card key may not  
work if any of the following occurs:  
(Message: Digital key(s) active.)  
śꢀ If you buy a used vehicle, you should  
confirm the message and delete the  
registered smartphone key and card  
key. In this case, you should carry  
your smart key.  
- Hyundai digital key app on the  
smartphone is deleted. (Required  
to reinstall the app)  
- Account log in information of  
Hyundai digital key app is expired.  
(Required to re-log in)  
- When you try to log in to another  
smartphone instead of the  
registered smartphone with same  
user account.  
- Smartphone rooting or app  
hacking is detected.  
- Smartphone battery or the vehicle  
battery is discharged.  
- Smartphone’s screen is off or  
locked.  
- NFC or Bluetooth is turned off on  
the smartphone settings.  
- Smartphone’s mobile network  
setting is off or airplane mode is  
activated.  
- A credit card is overlapped in the  
back of your smartphone or metal  
or thick case is used.  
- Use the card key with insert it  
into the wallet or card holder or  
overlapping with other cards.  
śꢀ If you keep place the NFC card  
of the digital key on the interior  
authentication pad (wireless  
charger) while driving, it may cause a  
malfunction of the NFC card.  
śꢀ You should remove your NFC card  
of the digital key on the interior  
authentication pad after turning on  
the engine.  
śꢀ Hyundai digital key app may not  
work properly when the NFC or  
Bluetooth communication between  
smartphone and car is not good.  
śꢀ If the remote control operation  
is executed where the mobile  
connection is weak, Bluetooth  
connection is poor due to lots of  
Bluetooth devices or there is an  
object such as metal or concrete, it  
might be delayed or the operable  
distance might decrease. Especially,  
you should not cover the smartphone  
with your hand or place other  
devices which can cause frequency  
interference. It may result in poor  
performance.  
5-22  
05  
- If you use a smart phone cover that  
uses wireless communication or is  
made of metal, the digital key NFC  
function may not work properly.  
Remove the smart phone cover  
before using the digital key NFC  
function.  
Digital key (Card key)  
śꢀThe vehicle may not be controlled by  
the smartphone if any of the following  
occurs:  
- Basic and necessary functions of  
the smartphone manufacturer are  
operating. (General call, urgent  
call, audio or NFC payment)  
ODN8A059243  
- Wireless earphone is operating.  
(General call, urgent call or audio)  
- The digital key app function such  
as basic setting or app launching  
is limited by prior policy according  
to the manufacturer while using a  
smartphone produced by domestic  
and foreign manufactures.  
à If you change the smartphone  
number, you should modify the user  
account information on the HYUNDAI  
customer web site to use the digital  
key app.  
à If the vehicle owner changes  
the smartphone device, the new  
smartphone should be registered in  
the car after deleting the registered  
digital key(smartphone).  
ODN8A059131  
Digital key (Card key) save  
1. Install Hyundai digital key app in  
main user’s smartphone and register  
the digital key (smartphone). Please  
refer to the registration method of the  
digital key (smartphone).  
2. Using the [Pair Card Key] menu on  
the digital key application, you can  
activate the Card Key registration  
mode.  
à If a sharer changes or reset the  
smartphone, the key should be re-  
shared from owner.  
à NFC authentication : enter the NFC  
authentication menu and contact  
the smartphone on the outside door  
handle.  
à Some of the old smartphone may  
not work properly. Please check the  
available smartphone models with  
your dealer.  
à Bluetooth authentication : enter the  
Bluetooth authentication menu and  
press the [OK] button for activation.  
à NFC antenna position on the  
smartphone can be confirmed  
on each smartphone’s manual or  
contact to customer service center  
of the smartphone manufacture.  
If you activate the registration mode,  
you should complete the Card saving  
process with in 5 minutes.  
à If you have not registered the digital  
key (smartphone), please register the  
digital key (card key) with two smart  
keys.  
5-23  
Convenience features  
Ã
3. Register the NFC card key on the  
User’s Settings menu after turning on  
the vehicle.  
à With Navigation screen : From the  
infotainment screen menu, go to  
[Setup] - [Vehicle] - [Digital Key] -  
[Card Key] then select the [Save] from  
submenu.  
à Without navigation screen : From  
cluster menu, go to [Digital Key] -  
[Card Key] and select [Save].  
ODN8A059243  
The [Save] button will be disabled if  
the digital key (Card key) is already  
saved.  
Please refer to “Digital Key Delete” in  
this manual and follow the digital key  
delete procedure in your car before  
Digital key save.  
4. Place the NFC card key onto the  
interior authentication pad (wireless  
charger). The saving process will  
begin automatically.  
5. If the key is enrolled, the message  
will be displayed on the infotainment  
screen or instrument cluster.  
ODN8A059132  
Digital key (Card key) deletion  
You should have the smart key to delete  
the digital key (card key) so please carry  
around the key.  
1. Get on the vehicle with the smart key.  
śꢀ Once the card key registration mode  
is activated, the process should be  
completed within 5 minutes. After  
then, you should reactivate once  
again for registration.  
śꢀ For the digital key(card key) saving,  
the smart key(fob) must be exist inside  
of vehicle.  
2. Delete the NFC card key on the User’s  
Settings menu after turning on the  
engine.  
à With Navigation screen : From the  
infotainment screen menu, go to  
[Setup] - [Vehicle] - [Digital Key] -  
[Card Key] then select the [Delete]  
from submenu.  
śꢀ Once a Card key is registered, it  
à Without navigation screen : From  
cluster menu, go to [Digital Key] -  
[Card Key] and select [Delete].  
cannot be reuse onto another vehicle.  
If there is no saved digital key(card key),  
[Delete] menu will not be activated.  
5-24  
05  
śꢀ To delete the saved digital key (card  
key), the smart key must be exist  
inside the vehicle.  
śꢀ The deleted digital key (card key) can  
be re-registered before registering a  
new digital key (card key).  
śꢀ If you try to register a new digital key  
(card key), the previously registered  
digital key (card key) cannot be used  
again.  
OTMA050020  
[1] : Door handle authentication pad  
NFC door lock/unlock  
You should contact digital key (card key)  
to door handle authentication pad (1,  
marked position near by the lock button)  
of driver’s (or front passenger’s) outside  
door for 2 seconds to lock or unlock the  
doors. If the Two Press Unlock feature  
is applied (press twice for unlocking),  
driver’s seat door will be unlocked by  
contacting the digital key (card key). In  
this state, if you contact one more time  
within 4 seconds, all the doors unlock.  
Inoperable condition  
If you do not contact the digital key (card  
key) to the center of the door handle  
authentication pad accurately., it may  
not work. In addition, if you overlap and  
use the key with NFC-enabled cards such  
as transportation card or credit card, it  
does not work.  
Note that if you try to lock your vehicle  
with digital key (card key) in following  
cases, the doors will not be locked and  
chime will sound for 3 seconds.  
śꢀ The Smart Key is in the vehicle.  
śꢀ The Engine Start/Stop button is in  
ACC or ON position.  
śꢀ Any of the doors, hood and trunk are  
open  
5-25  
Convenience features  
If the digital key (card key) does not  
work, please detach the key around  
4 inches (0.1 m) from the handle  
Start-up with Card key  
After placing your registered card key  
onto the interior authentication pad  
(wireless charger), step on the brake and  
press the Engine Start/Stop button.  
authentication pad and retry to contact.  
The card key may be damaged by the  
impact. It would not work properly if  
the key is damaged. You should buy a  
new card and register again. Long-time  
exposure to high temperature may cause  
the card key to malfunction. Please be  
careful not to expose the key to direct  
sunlight or high temperature.  
WARNING  
śꢀ If you do not place the digital key  
(card key) onto the center of the  
interior authentication pad (wireless  
charger) exactly, the card key may  
not be recognized. If the engine is  
not turned on, adjust and place the  
key again.  
śꢀ If you overlap and use the key  
with NFC-enabled cards such as  
transportation card or credit card,  
the card key may not be recognized.  
After unlock the door or start up the  
vehicle with digital key, even though  
the driver tries to lock the doors by the  
central door lock switch, the door lock  
will be once locked and immediately  
released at the moment of door closed.  
śꢀ If the digital key (card key) does not  
work, please detach the key around  
4 inches (0.1 m) from the handle  
authentication pad and retry to  
contact.  
śꢀ The card key may be damaged due to  
impact. It would not work properly if  
the key is damaged. You should buy a  
new card and register again.  
For more information, refer to the  
Engine Start/Stop button in chapter 6.  
5-26  
05  
„Type A  
CAUTION  
If you uncheck Enable digital keys, it is  
impossible to lock or unlock the doors  
or start up the vehicle with digital keys  
such as smartphone and card key. If  
you check Enable digital keys again, the  
registered digital keys(smartphone and  
card key) are available. Even though  
you stop the digital key function, the  
registered keys (smartphone and card  
key) are not deleted.  
ODN8A059133  
„Type B  
Personalized profile and vehicle  
settings  
Connect the registered digital key with  
personalized profile. Then in case you  
lock or unlock the door with the digital  
key NFC function or unlock the door  
remotely by digital key application  
Bluetooth connection, the vehicle  
will play the personalized user profile  
settings. Profile connection and  
personalization are available for Driver 1  
and Driver 2.  
ODN8A059247  
Digital key application/cancellation  
If you do not want to use the digital key  
(smartphone and card key), you can  
disable the function temporarily. You  
should have the smart key when you  
change the settings  
à With Navigation screen :  
From the infotainment screen menu,  
go to [Setup] - [Vehicle] - [Digital Key]  
- [Enable Digital Keys] (deselect)  
à Without navigation screen :  
From cluster menu, go to [Digital Key]  
- [Enable Digital Keys] (deselect)  
Information  
For the digital key disable, the smart key  
must be exist inside the car. For the digital  
key enable, the smart key does not need.  
5-27  
Convenience features  
Profile link/unlinked  
Profile link  
PRECAUTION for vehicle profile link and  
unlink  
When you link or unlink the profile of  
digital key, you should be careful of the  
following.  
śꢀ Profile link is possible to use with the  
digital key. (Infotainment Vehicle  
6HWWLQJVꢀ0RGHꢀƟꢀ'LJLWDOꢀ.H\ꢀƟꢀ(QDEOHꢀ  
Digital Keys)  
śꢀ Profile link information remains even  
when you set the digital key function  
disable.  
ꢂꢃꢀꢀ 6HOHFWꢀ6HWXSꢀƟꢀ8VHUꢀ3URILOHꢀƟꢀ  
3URILOHꢀ6HWWLQJVꢀƟꢀ/LQNꢀ'LJLWDOꢀ.H\ꢀ  
(Smartphone) on the infotainment  
system menu.  
2. Unlock and place your smartphone on  
the wireless charger according to a  
message and it automatically starts to  
interwork.  
3. It begins the profile link with a  
message.  
śꢀ Only the smart phone with digital key  
app enables you to link your profile.  
(Impossible to link with NFC card)  
4. If you select Link, the registered  
phone number’s digital key and the  
user’s profile are linked.  
śꢀ Profile link works only when the  
smart phone and the digital key are  
registered to the vehicle. The smart  
phone with another vehicle’s digital  
key cannot link profile.  
śꢀ If you remove the smart phone  
from the wireless charger before  
completing the profile link, it does not  
work.  
5. The interconnection process is  
completed with a message.  
Profile unlink  
1. Select Digital Key information on  
infotainment Vehicle Settings menu. It  
is possible to unlink only if the profile  
is interconnected.  
2. Profile unlink is completed with a  
message.  
śꢀ To unlink the profile, the smart phone  
does not need to be on the wireless  
charger.  
Information  
If you connect both Driver 1 and Driver 2  
with a single smartphone, the smartphone  
digital key always works as Driver 1.  
If you unlink the Driver 1, personalization  
function will operate as Driver 2.  
5-28  
05  
Vehicle personalization operation  
The personalization function linked with  
digital key works as following conditions:  
śꢀ Contact the driver’s door handle with  
the profile linked smart phone to lock  
or unlock the doors (Personalization  
does not operate when locking or  
unlocking the front passenger door.)  
Precaution for digital key profile link and  
unlink  
Profile operation according to door lock/  
unlock system is as follows.  
Personalization  
Item  
Operation  
Initial value  
Guest  
Profile linked  
smart phone  
key  
Profile unlinked  
smart phone  
key  
śꢀ Remote door unlock with the profile  
Linked profile  
linked smartphone digital key app.  
The profile linked with digital key can be  
changed manually in the infotainment  
system setup screen.  
Recently activated  
profile  
NFC card key  
Smart key  
śꢀ The personalization function using  
the digital key can be operated  
after linking the digital key on the  
infotainment system profile menu.  
śꢀ You should use the personalization  
function during stopping your vehicle  
safely.  
5-29  
Convenience features  
Vehicle personalization with digital key  
The available personalization function in the vehicle is as follows.  
System  
Personalization Item  
Position adjustment of image, Information display  
selection, Size and color of speedometer  
HUD  
Lamp  
Blink number of one-touch signal lamps  
Information display on the cluster, Voice volume,  
Welcome sound  
Cluster  
USM  
Seat position, O/S mirror position, Easy Access  
Intelligent driving posture assist (Smart IMS)  
Seat/Mirror  
Convenience Wireless charging system on/off  
Door  
Automatic door lock/unlock, Two Press Unlock  
Preferred volume of the navigation system, Recent  
destination  
Navigation  
User preset  
AVN  
My menu list settings, Radio preset  
Phone  
connectivity  
Bluetooth preferential connect  
CarPlay/Android Auto/MirrorLink On/Off  
Latest operation setup of the following functions:  
Operating  
condition  
Air conditioning  
Temperature, AUTO, air flow direction, air volume,  
air conditioner, air intake control, SYNC, Front  
windshield defroster, OFF  
For more information of personalization, refer to the infotainment system manual.  
CAUTION  
If you leave the digital key after locking or unlocking the doors or starting up the  
vehicle with the smart key, the doors can be locked by the central door lock. Please  
carry around the digital key all the time.  
5-30  
05  
DOOR LOCKS  
Remote key  
Operating door locks from  
outside the vehicle  
Mechanical key  
„Remote key  
OTMA050015MX  
To lock the doors, press the Door Lock  
button (1) on the remote key.  
To unlock the doors, press the Door  
Unlock button (2) on the remote key.  
OTM048001L  
„Smart key  
Once the doors are unlocked, they may  
be opened by pulling the door handle.  
When closing the door, push the door by  
hand. Make sure that doors are closed  
securely.  
OTM050083  
[A] : Unlock, [B] : Lock  
First, pull the outside door handle (1)  
and push the hook (2) located inside  
of outside door handle by using the  
mechanical key. And remove the cover  
(3).  
Turn the key toward the rear of the  
vehicle to lock and toward the front of  
the vehicle to unlock.  
If you lock/unlock the driver’s door with  
a key, a driver’s door will lock/unlock.  
Once the doors are unlocked, they may  
be opened by pulling the door handle.  
When closing the door, push the door by  
hand. Make sure that doors are closed  
securely.  
5-31  
Convenience features  
Smart key  
Operating door locks from inside  
the vehicle  
With the door lock button  
OTM048000  
To lock the doors, press the button on  
the outside door handle while carrying  
the smart key with you or press the door  
lock button on the smart key.  
To unlock the doors, press the button on  
the outside door handle while carrying  
the smart key with you or press the door  
unlock button on the smart key.  
Once the doors are unlocked, they may  
be opened by pulling the door handle.  
When closing the door, push the door by  
hand. Make sure that doors are closed  
securely.  
OTM048003  
śꢀ To unlock a door, push the door lock  
button (1) to the “Unlock” position.  
The red mark (2) on the door lock  
button will be visible.  
śꢀ To lock a door, push the door lock  
button (1) to the “Lock” position. If the  
door is locked properly, the red mark  
(2) on the door lock button will not be  
visible.  
śꢀ To open a door, pull the door handle  
(3) outward.  
śꢀ Front doors cannot be locked if the  
key is in the ignition switch and any  
front door is open.  
śꢀ Doors cannot be locked if the smart  
key is in the vehicle and any door is  
open.  
Information  
śꢀ In cold and wet climates, door lock  
and door mechanisms may not work  
properly due to freezing conditions.  
śꢀ If the door is locked/unlocked multiple  
times in rapid succession with either  
the vehicle key or door lock switch, the  
system may stop operating temporarily  
in order to protect the circuit and  
prevent damage to system components.  
5-32  
05  
With the central door lock/unlock  
switch  
Information  
If a power door lock ever fails to function  
while you are in the vehicle try one or  
more of the following techniques to exit:  
Operate the door unlock feature  
repeatedly (both electronic and manual)  
while simultaneously pulling on the door  
handle.  
Operate the other door locks and handles.  
Lower a front window and use the  
mechanical key to unlock the door from  
outside.  
OTM050215  
When pressing the ( ) portion (1) on the  
switch, all vehicle doors will lock.  
śꢀ If any door is opened, the doors will  
not lock even though the lock button  
(1) of the central door lock switch is  
pressed.  
śꢀ If the smart key is in the vehicle and  
any door is opened, the doors will  
not lock even though the lock button  
(1) of the central door lock switch is  
pressed.  
When pressing the ( ) portion (2) on the  
switch, all vehicle doors will unlock.  
5-33  
Convenience features  
WARNING  
CAUTION  
śꢀ The doors should always be fully  
closed and locked while the  
vehicle is in motion. If the doors  
are unlocked, the risk of being  
thrown from the vehicle in a crash is  
increased.  
Opening a door when something is  
approaching may cause damage or  
injury. Be careful when opening doors  
and watch for vehicles, motorcycles,  
bicycles or pedestrians approaching the  
vehicle in the path of the door.  
śꢀ Do not pull the inner door handle of  
the driver’s or passenger’s door while  
the vehicle is moving.  
WARNING  
If you stay in the vehicle for a long time  
while the weather is very hot or cold,  
there are risks of injuries or danger to  
life. Do not lock the vehicle from the  
outside when someone is in the vehicle.  
WARNING  
Do not leave the elderly, children or  
animals unattended in your vehicle. An  
enclosed vehicle can become extremely  
hot, causing death or serious injury  
to the elderly, unattended children  
or animals who cannot escape from  
the vehicle. Children might operate  
features of the vehicle that could injure  
them, or they could encounter other  
harm, possibly from someone gaining  
entry to the vehicle.  
WARNING  
Always secure your vehicle.  
Leaving your vehicle unlocked increases  
the potential risk to you or others from  
someone hiding in your vehicle.  
To secure your vehicle, while  
depressing the brake, shift the gear  
to the P (Park) position, engage the  
parking brake, and press the Engine  
Start/Stop button to the OFF position,  
close all windows, lock all doors, and  
always take the key with you.  
5-34  
05  
Auto door lock/unlock features  
Child-protector rear door locks  
(if equipped)  
Your vehicle is equipped with features  
that will automatically lock or unlock  
your vehicle based on settings you select  
in the infotainment system screen.  
Auto LOCK Enable on speed  
When this feature is set in the  
infotainment system screen, all the doors  
will be locked automatically when the  
vehicle exceeds 9 mph (15 km/h).  
Auto LOCK Enable on shift  
When this feature is set in the  
infotainment system screen, all the doors  
will be locked automatically when the  
vehicle is shifted out of P (Park) while the  
engine is running.  
OTM048005  
The child safety lock is provided to help  
prevent children seated in the rear from  
accidentally opening the rear doors. The  
rear door safety locks should be used  
whenever children are in the vehicle.  
The child safety lock is located on the  
edge of each rear door. When the child  
safety lock is in the lock position, the  
rear door will not open if the inner door  
handle is pulled.  
Auto UNLOCK On Shift to P  
When this feature is set in the  
infotainment system screen, all the doors  
will be unlocked automatically when the  
vehicle is shifted back into P (Park) while  
the engine is running.  
To lock the child safety lock, insert a  
small flat blade tool (like a screwdriver or  
similar) (1) into the slot and turn it to the  
lock position as shown.  
To allow a rear door to be opened from  
inside the vehicle, unlock the child safety  
lock.  
Auto UNLOCK Vehicle off  
When this feature is set in the  
infotainment system screen, all the doors  
will be unlocked automatically when the  
vehicle is turned off.  
See additional information in supplied  
Infotainment Manual.  
WARNING  
Additional unlock safety feature air  
bag deployment  
As an additional safety feature, all doors  
will be automatically unlocked when an  
impact causes the air bags to deploy.  
If children accidently open the rear  
doors while the vehicle is in motion,  
they could fall out of the vehicle. The  
rear door safety locks should always  
be used whenever children are in the  
vehicle.  
5-35  
Convenience features  
śꢀ If the power is supplied again after  
removing the battery or battery is  
discharged while the electronic child  
safety lock button is in the LOCK  
position, press the button once more  
to match the state of the indicator on  
the electronic child safety lock button  
and actual status of the electronic  
child safety lock function.  
Electronic child safety lock (if  
equipped)  
śꢀ If the airbag is activated while the  
electronic child safety lock button  
is in the LOCK position (indicator  
light ON), the rear doors will unlock  
automatically.  
OTM050084L  
śꢀ Vehicles equipped with the electronic  
child safety lock feature is not  
provided with a manual child safety  
lock.  
When the electronic child safety lock  
button is pressed and the indicator  
light on the button illuminates, the rear  
doors cannot be opened from inside the  
vehicle.  
WARNING  
śꢀ The rear door window cannot be  
opened or closed while the electronic  
child safety lock button is in the LOCK  
position (indicator light ON).  
If children accidentally opens the rear  
door while the vehicle is in motion, they  
could fall out of the vehicle. Electronic  
child safety lock should always be used  
whenever children are in the vehicle.  
For more details, refer to “Windows”  
section in this chapter.  
śꢀ Electronic child safety lock does not  
automatically turn on unless the driver  
presses the electronic child safety  
lock button.  
śꢀ If 3 minutes passes after the Engine  
Start/Stop button is pressed to the  
OFF or ACC, the indicator on the  
button turns off, and the driver cannot  
turn off electronic child safety lock by  
pressing the button. To turn off the  
function, press the Engine Start/Stop  
button to the ON position, and then  
press the electronic child safety lock  
button.  
5-36  
05  
NOTICE  
Safe Exit Assist (if equipped with  
electronic child safety lock)  
Child safety lock failure / Child safety  
lock error  
„Type A  
Safe Exit Assist helps prevent the rear  
occupant from opening the rear door.  
When an approaching vehicle from the  
rear area is detected after the vehicle  
stops, the rear doors will not unlock even  
when the driver tries to unlock the rear  
doors using the electronic child safety  
lock button.  
„Type B  
For more details, refer to “Safe Exit  
Assist (SEA)” section in chapter 7.  
OJX1059018L  
OJX1059254L  
When electronic child safety lock does  
not work even though the button is  
pressed, the message will be displayed  
and an alarm will sound. If this occurs,  
have the vehicle be inspected by an  
authorized HYUNDAI dealer.  
5-37  
Convenience features  
7+()7ǘ$/$50ꢀ6<67(0  
This system helps to protect your vehicle  
and valuables. The horn will sound and  
the hazard warning lights will blink  
continuously if any of the following  
occur:  
Information  
śꢀ Do not lock the doors until all  
passengers have left the vehicle. If the  
remaining passenger leaves the vehicle  
when the system is armed, the alarm  
will be activated.  
śꢀ If the vehicle is not disarmed with the  
smart key, open the doors by using the  
mechanical key and start the engine by  
directly pressing the Engine Start/Stop  
button with the smart key.  
śꢀ If the system is disarmed by unlocking  
the vehicle, but neither a door or the  
liftgate is opened within 30 seconds, the  
doors will relock and the system will  
rearm automatically.  
-
-
-
A door is opened without using the  
smart key.  
The liftgate is opened without using  
the smart key.  
The engine hood is opened.  
The alarm continues for 30 seconds, then  
the system resets. To turn off the alarm,  
unlock the doors with the smart key.  
The Theft Alarm System automatically  
sets 30 seconds after you lock the  
doors and the liftgate. For the system to  
activate, you must lock the doors and  
the liftgate from outside the vehicle with  
the smart key or by touching the touch  
sensor on the outside of the door handle  
with the smart key in your possession.  
The hazard warning lights will blink and  
the chime will sound once to indicate the  
system is armed.  
Once the security system is set, opening  
any door, the liftgate, or the hood  
without using the smart key will cause  
the alarm to activate.  
The Theft Alarm System will not set if the  
hood, the liftgate, or any door is not fully  
closed. If the system will not set, check  
the hood, the liftgate, or the doors are  
fully closed.  
Do not attempt to alter this system or  
add other devices to it.  
5-38  
05  
,17(*5$7('ꢀ0(025<ꢀ6<67(0ꢀǣ,)ꢀ(48,33('Ǥ  
Information  
śꢀ If the battery is disconnected, the  
memory settings will be erased.  
śꢀ If integrated memory system does not  
operate normally, have the system  
inspected by an authorized HYUNDAI  
dealer.  
Storing memory positions  
1. Shift to P (Park) while the Engine  
Start/Stop button is in the ON  
position.  
2. Adjust the driver’s seat position,  
side view mirror position, steering  
wheel position, instrument panel  
illumination intensity and head-up  
display height/brightness to the  
desired position.  
OTM050087  
Integrated Memory System for the  
driver’s seat is provided to store and  
recall the following memory settings with  
a simple button operation.  
śꢀ Driver’s seat position  
śꢀ Side View mirror position  
3. Press the SET button. The system  
will beep once and notify you ‘Press  
button to save settings’ on the cluster  
LCD display.  
4. Press one of the memory buttons (1  
or 2) within 4 seconds. The system  
will beep twice when the memory has  
been successfully stored.  
WARNING  
Never attempt to operate the  
integrated memory system while the  
vehicle is moving.  
This could result in loss of control, and  
an accident causing death, serious  
injury, or property damage.  
5. ‘Driver 1 (or 2) settings saved’ will  
appear on the cluster LCD display. The  
message appears only for the driver’s  
seat position memory setting.  
5-39  
Convenience features  
Recalling memory positions  
1. Shift to P (Park) while the Engine  
Start/Stop button is in the ON  
position.  
Resetting the system  
Take the following procedures to reset  
integrated memory system, when it does  
not operate properly.  
2. Press the desired memory button (1  
or 2). The system will beep once, and  
then the driver’s seat position, side  
view mirror position, steering wheel  
position, instrument panel illumination  
intensity and head-up display height/  
brightness will automatically adjust to  
the stored positions.  
Resetting integrated memory  
system  
1. Stop the vehicle and open the driver’s  
door with the Engine Start/Stop  
button in the ON position and the  
vehicle shifted to P (Park).  
2. Adjust the driver’s seat and seatback  
to the foremost position.  
3. Press the SET button and push  
forward the driver’s seat movement  
switch over 2 seconds simultaneously.  
3. ‘Driver 1 (or 2) settings applied’ will  
appear on the cluster LCD display.  
Information  
śꢀ If you press the SET button or the  
corresponding button which the  
setting is being recalled, the setting will  
temporarily deactivate. If you press the  
other buttons, the setting of the pressed  
button will activate.  
While resetting integrated memory  
system  
1. Resetting starts with a notification  
sound.  
2. The driver’s seat and seatback is  
adjusted to the rearward position with  
the notification sound.  
3. The driver’s seat and seatback is  
re-adjusted to the default position  
(central position) with the notification  
sound.  
For example, if you press the SET  
button or number 1 button with the  
number 1 setting in operation, the  
setting will temporarily deactivate. If  
you press the number 2 button, the  
number 2 setting will activate.  
śꢀ If you adjust the seat, rearview mirror,  
However, in the following cases, the  
resetting procedure and the notification  
sound may stop.  
śꢀ The memory button is pressed.  
śꢀ The seat control switch is operated.  
śꢀ The gear is shifted out of P (Park).  
steering wheel, instrument panel  
illumination or head-up display while  
recalling the stored positions, the pre-  
set settings will become ineffective.  
śꢀ The driving speed exceeds  
2 mph (3km/h).  
śꢀ The driver’s door is closed.  
5-40  
05  
NOTICE  
Easy access function  
śꢀ While integrated memory system  
is being reset, if the resetting  
and notification sound stops  
incompletely, restart the resetting  
procedure again.  
śꢀ Make sure that there is no objects  
around the driver’s seat in advance  
of resetting the integrated memory  
system.  
The system will move the driver’s seat  
automatically as follows:  
śꢀ With remote key  
- It will move the driver’s seat  
rearward when the ignition key is  
removed.  
- It will move the driver’s seat forward  
when the ignition key is inserted.  
śꢀ With smart key  
- It will move the driver’s seat  
rearward when the Engine Start/  
Stop button is pressed to the OFF  
position.  
- It will move the driver’s seat forward  
when the Engine Start/Stop button  
is pressed to the ACC or START  
position.  
You can activate or deactivate the Easy  
Access Function from the User Settings  
mode on the LCD display. ‘Convenience  
Ɵꢀ6HDWꢀ(DV\ꢀ$FFHVVꢀƟꢀ2IIꢁ1RUPDOꢁ  
Extended.  
For more details, refer to “LCD Display”  
In chapter 4.  
CAUTION  
Driver should be cautious when using  
this function to assure no injury to  
passenger or child on the back seat.  
In case of emergency the driver has to  
stop movement of front seat (when easy  
access feature is activated) by pressing  
SET button or any of the driver seat  
control switches.  
5-41  
Convenience features  
STEERING WHEEL  
Electric Power Steering (EPS)  
Information  
The system assists you with steering the  
vehicle. If the vehicle is turned off or  
if the power steering system becomes  
inoperative, you may still steer the  
vehicle, but it will require increased  
steering effort.  
The following symptoms may occur during  
normal vehicle operation:  
śꢀ The steering effort may be high  
immediately after pressing the Engine  
Start/Stop button to the ON position.  
This happens as the system performs  
the EPS system diagnostics. When the  
diagnostics are completed, the steering  
wheel effort will return to its normal  
condition.  
Should you notice any change in the  
effort required to steer during normal  
vehicle operation, have the system  
checked by an authorized HYUNDAI  
dealer.  
śꢀ When the battery voltage is low, you  
might have to put more steering effort.  
However, it is a temporary condition so  
that it will return to normal condition  
after charging the battery.  
śꢀ A click noise may be heard from the  
EPS relay after the Engine Start/Stop  
button is in the ON or OFF position.  
śꢀ Motor noise may be heard when the  
vehicle is at a stop or at a low driving  
speed.  
śꢀ When you operate the steering wheel  
in low temperatures, abnormal noise  
may occur. If the temperature rises, the  
noise will disappear. This is a normal  
condition.  
CAUTION  
If Electric Power Steering does not  
operate normally, the  
and the message ‘Check motor driven  
power steering’ will illuminate on the  
instrument cluster. You may steer the  
vehicle, but it will require increased  
steering efforts. Take your vehicle to  
an authorized HYUNDAI dealer or to  
a service station and have the system  
checked as soon as possible.  
warning light  
śꢀ When an error is detected from EPS,  
the steering effort assist function will  
not be activated in order to prevent  
fatal accidents. Instrument cluster  
warning lights may be on or the  
steering effort may be high. If these  
symptoms occur, drive the vehicle to  
a safe area as soon as it is safe to do  
so. Have the system be checked by an  
authorized HYUNDAI dealer as soon  
as possible.  
5-42  
05  
Tilt / Telescopic steering  
Information  
When adjusting the steering wheel to a  
comfortable position, adjust the steering  
wheel so that it points toward your chest,  
not toward your face. Make sure you can  
see the instrument cluster warning lights  
and gauges. After adjusting, push the  
steering wheel both up and down to be  
certain it is locked in position.  
Sometimes the lock release lever may not  
engage completely. This may occur when  
the gears of the locking mechanism do not  
completely mesh. If this occurs, pull down  
on the lock-release lever, readjust the  
steering wheel again, and then pull back  
up on the release lever to lock the steering  
wheel in place.  
Always adjust the position of the steering  
wheel before driving.  
Heated steering wheel  
(if equipped)  
WARNING  
NEVER adjust the steering wheel while  
driving. This may cause loss of vehicle  
control resulting in an accident.  
OTM050009  
When the ignition switch is in the ON  
position or when the engine is running,  
press the heated steering wheel button  
to warm the steering wheel.  
OTM050008  
The indicator on the button will  
illuminate.  
To turn the heated steering wheel off,  
press the button again. The indicator on  
the button will turn off.  
To adjust the steering wheel angle and  
height:  
1. Pull down the lock-release lever (1).  
2. Adjust the steering wheel to the  
desired angle (2) and distance  
forward/back (3).  
3. Pull up the lock-release lever to lock  
the steering wheel in place.  
5-43  
Convenience features  
śꢀ Auto Comfort Control (for driver’s  
Horn  
seat) (if equipped)  
- The heated steering wheel  
automatically controls the steering  
wheel temperature depending on  
the ambient temperature and the  
set climate control temperature  
when the engine is running. If the  
heated steering wheel switch is  
pushed, the heated steering wheel  
will have to be controlled manually.  
To use this function, it must be  
activated from the Settings menu in  
the AVN system screen.  
OTM050088  
To sound the horn, press the area  
indicated by the horn symbol on your  
steering wheel (see illustration). The  
horn will operate only when this area is  
pressed.  
- The heated steering wheel defaults  
to the OFF position whenever the  
ignition switch is ON. However, if  
the Auto Comfort Control function  
is ON, the heated steering wheel  
will turn on and off depending on  
the ambient temperature and the  
set climate control temperature.  
NOTICE  
Do not strike the horn severely to  
operate it, or hit it with your fist. Do not  
press on the horn with a sharp-pointed  
object.  
For more details, contact an authorized  
HYUNDAI dealer.  
Information  
The heated steering wheel will turn off  
automatically approximately 30 minutes  
after the heated steering wheel is turned  
on.  
NOTICE  
Do not install any cover or accessory  
on the steering wheel. This cover or  
accessory could cause damage to the  
heated steering wheel system.  
5-44  
05  
0,55256  
Electric Chromic Mirror (ECM)  
(if equipped)  
Inside rearview mirror  
Before driving your vehicle, check to  
see that your inside rearview mirror is  
properly positioned. Adjust the rearview  
mirror so that the view through the rear  
window is properly centered.  
WARNING  
Make sure your line of sight is not  
obstructed. Do not place objects in the  
rear seat, cargo area, or behind the rear  
headrests which could interfere with  
your vision through the rear window.  
OTM050019  
[A] : Indicator  
Some vehicles come equipped with an  
electrochromic mirror that helps control  
glare while driving at night or under low  
light driving conditions.  
When the engine is running, the glare is  
automatically controlled by the sensor  
mounted in the rearview mirror. The  
sensor detects the light level around the  
vehicle, and automatically adjusts to  
control the headlight glare from vehicles  
behind you.  
Whenever the the gear is shifted to R  
(Reverse), the mirror will automatically  
go to the brightest setting in order to  
improve the driver’s view behind the  
vehicle.  
WARNING  
To prevent serious injury during an  
accident or deployment of the air bag,  
do not modify the rearview mirror and  
do not install a wide mirror.  
WARNING  
NEVER adjust the mirror while driving.  
This may cause loss of vehicle control  
resulting in an accident.  
NOTICE  
When cleaning the mirror, use a paper  
towel or similar material dampened  
with glass cleaner. Do not spray glass  
cleaner directly on the mirror as this  
may cause the liquid cleaner to enter  
the mirror housing.  
5-45  
Convenience features  
Day/night rearview mirror  
(if equipped)  
OTMA050002  
(1) HomeLink Channel 1  
(2) HomeLink Channel 2  
(3) HomeLink Channel 3  
(4) Garage Door Opener Status Indicator:  
Closing or Closed  
(5) HomeLink Operation Indicator  
(6) Garage Door Opener Status Indicator:  
Opening or Opened  
OTM050018  
[A]: Day, [B]: Night  
Make this adjustment before you start  
driving and while the day/night lever is in  
the day position.  
Pull the day/night lever towards you to  
reduce glare from the headlights of the  
vehicles behind you during night driving.  
(7) HomeLink User Interface Indicator  
Remember that you lose some rearview  
clarity in the night position.  
Automatic-Dimming Night Vision Safety™  
(NVS®) Mirror (if equipped)  
Electrochromic mirror (ECM) with  
HomeLink® system (if equipped)  
Your vehicle may be equipped with  
a Gentex Automatic-Dimming Mirror  
with an Integrated HomeLink® Wireless  
Control System.  
During nighttime driving, this feature  
will automatically detect and reduce  
rearview mirror glare. The HomeLink®  
Universal Transceiver allows you to  
activate your garage door(s), electric  
gate, home lighting, etc.  
The NVS® Mirror automatically reduces  
glare by monitoring light levels in the  
front and the rear of the vehicle. Any  
object that obstructs either light sensor  
will degrade the automatic dimming  
control feature.  
For more information regarding NVS®  
mirrors and other applications, please  
refer to the Gentex website:  
www.gentex.com  
Your mirror will automatically dim  
upon detecting glare from the vehicles  
traveling behind you.  
The mirror defaults to the ON position  
each time the vehicle is started.  
5-46  
05  
Integrated HomeLink® Wireless Control  
System  
1. Programming HomeLink®  
The following steps show how to  
program HomeLink. If you have any  
questions or are having difficulty  
programming your HomeLink buttons,  
refer to the HomeLink website or call the  
HomeLink customer support toll-free  
number. Do this before going back to the  
dealer who sold you the car.  
The HomeLink® Wireless Control System  
provides a convenient way to replace  
up to three hand held radio-frequency  
transmitters used to activate compatible  
devices such as gate operators, garage  
door openers, entry door locks, security  
systems, and home lighting.  
śꢀ Visit the HomeLink website at: www.  
homelink.com. Then at the top of the  
page, choose your vehicle make. Then  
watch the You Tube video, and/or  
NOTICE  
HomeLink® operates while the ignition  
switch is in the ACC or ON position  
for safety reasons. It is to prevent  
unintentional security problems from  
happening when the vehicle is parked  
outside the garage.  
access additional website information.  
śꢀ If you choose to access the website  
via your cell phone, scan the QR code.  
WARNING  
Before programming HomeLink® to a  
garage door opener or gate operator,  
make sure people and objects are out  
of the way of the device to prevent  
potential harm or damage. Do not  
use the HomeLink® with any garage  
door opener that lacks the safety  
stop and reverse features required  
by U.S. federal safety standards (this  
includes any garage door opener model  
manufactured before April 1, 1982).  
A garage door that cannot detect an  
object - signaling the door to stop and  
reverse - does not meet current U.S.  
federal safety standards. Using a garage  
door opener without these features  
increases the risk of serious injury or  
death.  
śꢀ Or call HomeLink customer support  
at 1-800-355-3515 (Please have the  
vehicle make/model and the opener  
device make/model readily available.)  
For more information, contact  
HomeLink® at www.homelink.com, or  
call Home-Link customer support at  
1-800-355-3515.  
It is also recommended that a new  
battery be replaced in the handheld  
transmitter of the device being trained  
to HomeLink® for quicker training and  
accurate transmission of the radio  
frequency.  
5-47  
Convenience features  
1) Programming Preparation  
OTMA050005  
2. Position the garage door opener  
OTMA050003  
remote 1 – 3 inches (2 – 8cm) away  
from the HoleLink buttons.  
1. When programming a garage door  
opener, it is advised to park the  
vehicle outside of the garage.  
2. It is recommended that a new battery  
be placed in the handheld transmitter  
of the device being programmed to  
HomeLink for quicker training and  
accurate transmission of the radio-  
frequency signal.  
3. While the HomeLink indicator light (7)  
is flashing orange, press and hold the  
hand-held remote button. Continue  
pressing the handheld remote button  
until the HomeLink indicator light (7)  
light changes from orange to green.  
You may now release the handheld  
remote button.  
4. Wait until your garage door comes  
to a complete stop, regardless of  
position, before proceeding to the  
next steps.  
3. Place the ignition switch to the ACC  
(Accessory) position for programming  
of HomeLink.  
2) Programming a New HomeLink®  
5. Press and release the HomeLink  
button you are programming and  
observe the indicator light.  
śꢀIf the indicator light remains solid  
green, your device should operate  
when the HomeLink button is  
pressed. At this point, if your device  
operates, programming is complete.  
śꢀIf the indicator light rapidly  
flashes green, firmly press, hold  
for two seconds and release the  
HomeLink button up to three times  
in a row slowly to complete the  
programming process. Do not press  
the HomeLink button rapidly. At  
this point if your device operates,  
programming is complete. If the  
device does not operate, continue  
with step 6.  
OTMA050004  
1. Press and release the HomeLink  
button (1), (2) or (3), you would like  
to program. The HomeLink indicator  
light (7) will flash orange slowly (if  
not, perform the steps of “Erasing  
HomeLink Buttons” section, and start  
over).  
5-48  
05  
3) Two-Way Communication  
6. At the garage door opener motor,  
(security gate motor, etc.) locate the  
“Learn, Smart, Set” or “Program”  
button. This can usually be found  
where the hanging antenna wire is  
attached to the motor-head unit (see  
the device’s manual to identify this  
button). The name and color of the  
button may vary by manufacturer.  
Programming (For select garage door  
openers)  
If your garage door opener has the  
‘myQ’ logo on its side, your opener  
likely has Two-Way Communication  
capability. HomeLink has the capability  
to establish Two-Way Communication  
with your garage door opener. HomeLink  
can receive and display “closing”  
or “opening” status messages from  
compatible garage door openers. At  
any time, Home-Link can also recall  
and display the last recorded status  
communicated by the garage door  
opener to indicate your garage door  
being “closed” or “opened.  
To check if your garage door opener is  
compatible with this feature, refer to  
www.homelink.com/compatible/Two-  
way-Communication. If your garage  
door opener has this functionality, AND  
the Two-Way Communication indicators  
(4), (6) in the mirror appear while the  
garage door is opening/closing, then  
no further steps are needed. Two-Way  
Communication Programming is already  
complete. However, if your garage door  
opener has this functionality, AND the  
Two-Way Communication indicators (4),  
(6) in the mirror DO NOT appear while  
the garage door is opening/closing, use  
the following instructions to enable this  
functionality.  
ODL3A040504  
à A ladder and/or second person may  
simplify the following steps.  
7. Firmly press and release the “Learn,  
“Smart, Set” or “Program” button.  
You now have up to 30 seconds in  
which to complete the next step.  
8. Return to the vehicle and firmly press,  
hold for two seconds and release,  
the HomeLink button up to three  
times in a row slowly. Do not press  
the HomeLink button rapidly. As soon  
as you see the garage door start to  
move, stop pressing any buttons  
until a few seconds after the garage  
door has come to a complete stop,  
regardless of position. At this point,  
programming is complete and your  
device should operate when the  
HomeLink button is pressed and  
released.  
1. In your vehicle, press and hold the  
programmed HomeLink button for 2  
seconds, then release. Confirm that  
the garage door is moving. AFTER it  
stops, you will have one minute to  
complete the following steps:  
à A ladder and/or second person may  
simplify the following steps.  
5-49  
Convenience features  
4) Canadian Programming  
2. On your garage door opener in your  
garage, locate the “Learn” button  
(usually near where the hanging  
antenna wire is attached to the garage  
door opener). If there is difficulty  
locating this button, reference the  
device’s owner’s manual.  
Canadian radio-frequency laws require  
transmitter remote signals to “time-  
out” (or quit) after a couple seconds of  
transmission, which may not be long  
enough for HomeLink to pick up the signal  
during programming.  
3. Press and release the “Learn” button.  
4. A light on your garage door opener  
may flash, and your Two-Way  
If you live in Canada or you are having  
difficulties programming a gate operator  
or garage door opener by using the  
programming procedures, replace  
“Programming a New HomeLink Button”  
step 3 with the following:  
Communication indicators (4), (6) in  
your vehicle may flash, confirming  
completion of the process.  
While the HomeLink indicator light (7) is  
flashing orange, press and release (“cycle”)  
your device’s handheld remote every two  
seconds until the HomeLink indicator light  
(7) changes from orange to green. You may  
now release the hand-held remote button.  
Then proceed with “Programming a New  
HomeLink Button” step 4.  
5. Return to the vehicle and firmly  
press and release the programmed  
HomeLink button to activate  
your garage door. The Two-Way  
Communication indicators (4), (6)  
flash in orange when the door is  
moving. Do not make any additional  
button presses until AFTER the garage  
door has come to a complete stop.  
6. Your Two-Way Communication  
programming is now complete.  
Information  
If your garage door opener has Two-  
Way Communication functionality,  
it is possible for HomeLink to stop  
functioning the garage door shortly  
after initial programming, IF the Two-  
Way Communication Programming  
wasn’t properly completed. This  
usually happens after the first 10 times  
a programmed HomeLink button is  
pressed. If you experience this, completing  
the “Programming a New HomeLink  
Button” and “Two-Way Communication  
Programming” will restore door  
operation.  
5-50  
05  
2. Operating HomeLink®  
1) Operating HomeLink®  
OTMA050007  
2. The indicator (4) and (6) operates as  
below, if your garage door opener  
has Two-Way Communication  
functionality.  
śꢀ If the indicator (4) flashes in Orange,  
it indicates that the garage door is  
“Closing.  
OTMA050004  
1. Press and release the desired  
programmed HomeLink button (1, 2  
or 3).  
Information  
The HomeLink indicator (7) should  
light green, solid or flashing, and your  
programmed device should operate.  
If your device does not operate, the  
HomeLink programming was not  
successful, and you’ll need to reprogram  
the button.  
śꢀ The indicator (4) turns solid green  
once the garage door has closed.  
śꢀ If the indicator (6) flashes in Orange,  
it indicates that the garage door is  
“Opening.  
śꢀ The indicator (6) turns solid green  
once the garage door has fully  
opened.  
śꢀ If the indicator (4) or (6) does not  
turn to green, it indicates that the  
last status of garage door was not  
received properly. The HomeLink  
mirror tries to receive the last known  
status of the garage door for a few  
seconds.  
2) Two-Way Communication Display  
Behavior  
OTMA050006  
1. Press and release one of the  
programmed HomeLink buttons (1, 2  
or 3).  
5-51  
Convenience features  
3) Recalling Garage Door Status  
HomeLink mirror with Two-Way  
2) The following instructions will erase  
ALL HomeLink® programming from  
ALL buttons:  
Communication provides a way to view  
the last stored message from the garage  
door opener. In order to recall the last  
known status of the last activated device,  
press the buttons “1 and 2” OR “2 and 3”  
simultaneously.  
śꢀ If the indicator (4) appears solid  
Green, it indicates that the last  
activated device was “closed”  
properly.  
śꢀ If the indicator (6) appears solid  
Green, it indicates that the last  
OTMA050008  
activated device was “open” properly.  
1. Press and hold the buttons (1) and (3)  
simultaneously.  
2. The HomeLink indicator light (7) will  
illuminate solid Orange for about 10  
seconds.  
3. Release the buttons once the  
HomeLink indicator light (7) changes  
to Green and flashes rapidly.  
3. Erasing HomeLink® Buttons  
1) Erasing and Reprogramming a Single  
HomeLink® Button:  
1. Press and hold the desired HomeLink  
button you want to re-program. DO  
NOT release the button.  
2. The HomeLink indicator light (7) will  
illuminate solid green. Release the  
button as soon as the HomeLink  
indicator light (7) begins to flash  
orange, usually about 20 seconds.  
4. Now all three HomeLink buttons  
(1), (2) and (3) are cleared of any  
programming.  
Information  
3. Proceed with the steps in the  
“Programming a New HomeLink  
Button” section.  
HomeLink® and the HomeLink® House  
logo are registered trademarks of Gentex  
Corporation.  
The myQ logo is a registered trademark of  
Information  
The Chamberlain Group, Inc.  
If you do not complete the re-  
programming of a new device to the  
button, it will revert to the previously  
stored programming.  
5-52  
05  
FCC (USA) and ISED (Canada)  
FCC (Htats-Unis) et ISED (Canada)  
This device complies with FCC rules  
part 15 and Innovation, Science, and  
Economic Development Canada RSS-  
210. Operation is subject to the following  
two conditions: (1) This device may not  
cause harmful interference, and (2) This  
device must accept any interference that  
may be received including interference  
that may cause undesired operation.  
WARNING: The transmitter has been  
tested and complies with FCC and  
ISED rules. Changes or modifications  
not expressly approved by the party  
responsible for compliance could void  
the user’s authority to operate the  
device.  
This equipment complies with FCC  
and ISED radiation exposure limits set  
forth for an uncontrolled environment.  
End Users must follow the specific  
operating instructions for satisfying RF  
exposure compliance. This transmitter  
must be at least 20cm from the user and  
must not be co-located or operating in  
conjunction with any other antenna or  
transmitter.  
Cet appareil est conforme aux  
règlements de la FCC, section 15, et  
au CNR-210 d’Innovation, Sciences et  
Dhveloppement économique Canada. Le  
fonctionnement est assujetti aux deux  
conditions suivantes : (1) cet appareil ne  
doit pas causer d’interférences nuisibles  
et (2) cet appareil doit accepter toute  
interférence reçue, y compris celle qui  
pourrait entraîner un dysfonctionnement.  
MISE EN GARDE : L’émetteur a subi des  
tests et est conforme aux règlements de  
la FCC et d’ISDE. Les changements ou  
modifications non approuvés explicitement  
par la partie responsable de la conformité  
pourraient rendre caduque l’autorisation de  
l’utilisateur de se servir du dispositif.  
Cet appareil est conforme aux limites  
d’exposition aux radiations de la FCC et  
d’ISDE établies pour un environnement  
non contrôlé. Les utilisateurs finaux doivent  
respecter les instructions d’utilisation  
spécifiques pour satisfaire aux exigences  
de conformité aux expositions de RF.  
L’émetteur doit se trouver à 20 cm au  
minimum de l’utilisateur et ne doit pas  
être situé au même endroit que tout autre  
émetteur ou antenne ni fonctionner avec  
un autre émetteur ou antenne.  
Méjico  
La operación de este equipo está sujeta  
a las siguientes dos condiciones: (1) es  
posible que este equipo o dispositivo  
pueda no causar interferencia dañina, y  
(2) este dispositivo o dispositivos deben  
aceptar cualquier interferencia, que  
incluye la interferencia que puede causar  
su operación no deseada.  
5-53  
Convenience features  
HomeLink 5 Programing Flow Chart  
OOS040475N  
5-54  
05  
Side View mirrors  
WARNING  
Do not adjust or fold the side view  
mirrors while driving. This may cause  
loss of vehicle control resulting in an  
accident.  
NOTICE  
śꢀ Do not scrape ice off the mirror face;  
this may damage the surface of the  
glass.  
śꢀ If the mirror is jammed with ice, do  
not adjust the mirror by force. Use  
an approved de-icer (not radiator  
antifreeze) spray, or a sponge or soft  
cloth with very warm water, or move  
the vehicle to a warm place and  
allow the ice to melt.  
śꢀ Do not clean the mirror with harsh  
abrasives, fuel or other petroleum  
based cleaning products.  
OTM048015  
Your vehicle is equipped with both left-  
hand and right-hand side view mirrors.  
The mirrors can be adjusted remotely  
with the mirror adjustment control  
switch. The side view mirrors can be  
folded to help prevent damage when  
going through an automatic car wash or  
when passing through a narrow street.  
The right side view mirror is convex.  
Objects seen in the mirror are closer than  
they appear.  
Use the inside rear view mirror or look  
back directly to determine the actual  
distance of other vehicles prior to  
changing lanes.  
Make sure to adjust the side view mirrors  
to your desired position before you begin  
driving.  
5-55  
Convenience features  
Adjusting the side view mirrors  
Folding the side view mirror  
OTM050089  
OTM048430L  
1. Move the lever (1) either to the L (left  
side) or R (right side) to select the side  
view mirror you would like to adjust.  
2. Use the mirror adjustment control (2)  
to position the selected mirror up,  
down, left or right.  
Manual type  
To fold the side view mirror, grasp the  
housing of the mirror and then fold it  
toward the rear of the vehicle.  
3. After adjustment, move the lever (1)  
to the middle to prevent inadvertent  
adjustment.  
NOTICE  
śꢀ The mirrors stop moving when  
they reach the maximum adjusting  
angles, but the motor continues to  
operate while the switch is pressed.  
Do not press the switch longer than  
necessary, because this can damage  
the motor.  
śꢀ Do not attempt to adjust the side  
view mirrors by hand, because this  
can damage the motor.  
OTM050090  
Electric type  
The side view mirror can be folded or  
unfolded by pressing the switch.  
5-56  
05  
śꢀ ,Iꢀœ&RQYHQLHQFHꢀƟꢀ:HOFRPHꢀPLUURUꢁ  
OLJKWꢀƟꢀ2QꢀGRRUꢀXQORFNŔꢀLVꢀVHOHFWHGꢀLQꢀ  
the User Settings mode on the LCD  
display, the outside mirror will fold or  
unfold automatically as follows:  
Reverse parking aid (if equipped)  
- The mirror will fold or unfold when  
the door is locked or unlocked by  
the smart key.  
- The mirror will fold or unfold when  
the door is locked or unlocked by  
the button on the outside door  
handle.  
śꢀ ,Iꢀœ&RQYHQLHQFHꢀƟꢀ:HOFRPHꢀ  
OTM050020  
PLUURUꢁOLJKWꢀƟꢀ2QꢀGRRUꢀXQORFNŔꢀDQGꢀ  
œ&RQYHQLHQFHꢀƟꢀ:HOFRPHꢀPLUURUꢁOLJKWꢀ  
Ɵꢀ2QꢀGULYHUꢀDSSURDFKŔꢀLVꢀVHOHFWHGꢀLQꢀ  
the User Settings mode on the LCD  
display, the outside mirror will unfold  
automatically when you approach the  
vehicle (all doors closed and locked)  
with a smart key in possession.  
When the gear is shifted to the R  
(Reverse) position, the side view mirror(s)  
will rotate downwards to aid with driving  
in reverse.  
The position of the side view mirror  
switch (1) determines whether or not the  
mirrors will move:  
Left/Right : When either the L (Left) or  
R (Right) switch is selected,  
both side view mirrors will  
move.  
Neutral : When neither switch is  
selected, the outside rearview  
mirrors will not move.  
NOTICE  
The electric type side view mirror  
operates even though the ignition  
switch is in the OFF position. However,  
to prevent unnecessary battery  
discharge, do not adjust the mirrors  
longer than necessary while the engine  
is not running.  
The side view mirrors will automatically  
revert to their original positions if any of  
the following occur:  
śꢀ The Engine Start/Stop button is  
pressed to either the OFF position or  
the ACC position.  
NOTICE  
Do not fold the electric type side view  
mirror by hand. It could cause motor  
failure.  
śꢀ The gear is shifted to any position  
except R (Reverse).  
śꢀ The side view mirror adjustment  
button is not selected.  
5-57  
Convenience features  
WINDOWS  
OTMA050018  
(1) Driver’s door power window switch  
(5) Window opening and closing  
(2) Front passenger’s door power  
window switch*  
(3) Rear door (left) power window  
switch*  
(6) Automatic power window*  
(7) Power window lock switch  
* : if equipped  
(4) Rear door (right) power window  
switch*  
5-58  
05  
Auto up/down window (if equipped)  
Power windows  
Pressing or pulling up the power window  
switch momentarily to the second  
detent position (6) completely lowers or  
lifts the window even when the switch  
is released. To stop the window at the  
desired position while the window is in  
operation, pull up or press down and  
release the switch.  
The ignition switch must be in the ON  
position to be able to raise or lower  
the windows. Each door has a Power  
Window switch to control that door’s  
window. The driver has a Power Window  
Lock switch which can block the  
operation of rear passenger windows.  
The power windows will operate for  
approximately 3 minutes after the  
ignition switch is placed in the ACC or  
OFF position. However, if the front doors  
are opened, the Power Windows cannot  
be operated even within the 3 minutes  
period.  
Resetting the power windows  
If the power windows do not operate  
normally, the automatic power window  
system must be reset as follows:  
1. Press the ignition switch to the ON  
position.  
2. Close the window and continue  
pulling up on the power window  
switch for at least one second.  
Window opening and closing  
If the power windows do not operate  
properly after resetting, have the system  
be inspected by an authorized HYUNDAI  
dealer.  
WARNING  
The automatic reverse feature doesn’t  
activate while resetting the power  
window system.Make sure body parts  
or other objects are safely out of the  
way before closing the windows to  
avoid injuries or vehicle damage.  
OTM050213  
To open:  
Press the window switch down to the  
first detent position (5). Release the  
switch when you want the window to  
stop.  
To close:  
Pull the window switch up to the first  
detent position (5). Release the window  
switch when you want the window to  
stop.  
5-59  
Convenience features  
Automatic reverse (if equipped)  
WARNING  
Make sure body parts or other objects  
are safely out of the way before closing  
the windows to avoid injuries or vehicle  
damage.  
Objects less than 0.16 in (4 mm) in  
diameter caught between the window  
glass and the upper window channel  
may not be detected by the automatic  
reverse window and the window will  
not stop and reverse direction.  
OTM050091  
Power window lock button  
If a window senses any obstacle while it  
is closing automatically, it will stop and  
lower approximately 12 in. (30 cm) to  
allow the object to be cleared.  
If the window detects the resistance  
while the power window switch is  
pulled up continuously, the window  
will stop upward movement then lower  
approximately 1 in. (2.5 cm).  
If the power window switch is pulled  
up continuously again within 5 seconds  
after the window is lowered by the  
automatic window reverse feature,  
the automatic window reverse will not  
operate.  
OTM050092L  
The driver can disable the power window  
switches on the rear passenger doors by  
pressing the power window lock button.  
When the power window lock button is  
pressed:  
Information  
The automatic reverse feature is only  
active when the “Auto Up” feature is used  
by fully pulling up the switch to the second  
detent.  
śꢀ The driver’s master control can  
operate all the power windows.  
śꢀ The front passenger’s control can  
operate the front passenger’s power  
window.  
NOTICE  
Do not install any accessories on the  
windows. The automatic reverse  
feature may not operate.  
śꢀ The rear passenger’s control cannot  
operate the rear passengers’ power  
window.  
5-60  
05  
à If the power window lock button is  
operated (indicator turns on), rear  
passenger cannot open the rear door  
(if equipped with the Electronic Child  
Safety Lock System).  
For more details, refer to “Electronic  
Child Safety Lock System” system in this  
chapter.  
WARNING  
Do not allow children to play with the  
power windows. Keep the driver’s  
door power window lock button in the  
LOCK position. Serious injury or death  
can result from unintentional window  
operation by a child.  
NOTICE  
śꢀ To prevent possible damage to the  
power window system, do not open  
or close two windows or more at the  
same time. This will also ensure the  
longevity of the fuse.  
śꢀ Never try to operate the main  
switch on the driver’s door and the  
individual door window switch in  
opposite directions at the same time.  
If this is done, the window will stop  
and cannot be opened or closed.  
5-61  
Convenience features  
3$125$0,&ꢀ681522)ꢀǣ,)ꢀ(48,33('Ǥ  
If your vehicle is equipped with a  
WARNING  
sunroof, you can slide or tilt your sunroof  
with the sunroof control switch located  
on the overhead console.  
śꢀ Never adjust the sunroof or sunshade  
when your vehicle stops. This could  
result in loss of control and an  
accident that may cause, serious  
injury, or property damage.  
śꢀ Do not leave the engine running  
and the key in your vehicle with  
unsupervised children. Unattended  
children could operate the sunroof,  
which could result in serious injury.  
śꢀ Do not sit on the top of the vehicle. It  
may cause injury or vehicle damage.  
OTM050226L  
NOTICE  
The sunroof can only be operated when  
the ignition switch or Engine Start/Stop  
button is in the ON or START position.  
The sunroof can be operated for  
approximately 3 minutes after the  
ignition switch or Engine Start/Stop  
button is in the ACC or LOCK/OFF  
position.  
Do not operate the sunroof when roof  
bars are installed on the vehicle or  
when there is luggage on the roof.  
However, if the front door is open, the  
sunroof cannot be operated even within  
the 3 minute period.  
5-62  
05  
Power sunshade  
Tilt open/close  
OTM050023  
OTM052025L  
Use the power sunshade to block direct  
sunlight coming through the sunroof  
glass.  
- Push the sunroof switch rearward to the  
first detent position, the power sunshade  
automatically slides open.  
śꢀ Push the sunroof switch upward, the  
sunroof glass tilts open. However, if  
the power sunshade is closed, the  
sunshade will open first.  
śꢀ Push the sunroof switch forward, the  
sunroof glass automatically closes.  
- Push the sunroof switch forward to the  
first detent position, the power sunshade  
automatically closes. However, if the  
sunroof glass is open, the glass will close  
first.  
To stop the sunroof movement at any  
point, push the sunroof switch in any  
direction.  
To stop the power sunshade at any point,  
push the sunroof switch in any direction.  
NOTICE  
Do not pull or push the power sunshade  
by hand as such action may damage  
the power sunshade or cause it to  
malfunction.  
Information  
Wrinkles formed on the power sunshade  
are normal due to material characteristic.  
5-63  
Convenience features  
Automatic reversal  
Slide open/close  
ODH043039  
OTM050024  
If the power sunshade or sunroof glass  
senses any obstacle while it is closing  
automatically, it will reverse direction  
then stop at a certain position.  
śꢀ Push the sunroof switch rearward, the  
sunroof glass slides open. However,  
if the power sunshade is closed, the  
power sunshade will open first.  
The auto reverse function may not  
work if an object thin or soft is caught  
between the sliding power sunshade or  
sunroof glass and sunroof sash.  
Push the sunroof switch forward, the  
sunroof glass closes.  
śꢀ Push the sunroof switch forward or  
rearward to the first detent position,  
the sunroof glass moves until the  
switch is released.  
śꢀ Push the sunroof switch forward  
or rearward to the second detent  
position, the sunroof glass operates  
automatically (auto slide feature).  
WARNING  
śꢀ Make sure heads, hands, arms or  
any other body parts or objects are  
out of the way before operating the  
sunroof. Body parts or objects may  
get caught causing injuries or vehicle  
damage.  
śꢀ Never deliberately use your body  
parts to test the automatic reversal  
function. The power sunshade or  
sunroof glass may reverse direction,  
but there is a risk of injury.  
To stop the sunroof movement at any  
point, push the sunroof switch in any  
direction.  
5-64  
05  
NOTICE  
Resetting the sunroof  
śꢀ Do not continue to push the sunroof  
switch after the sunroof is fully  
opened, closed, or tilted. Damage to  
the sunroof motor could occur.  
śꢀ Continuous operations such as slide  
open/close, tilt open/close, etc., may  
cause the motor or sunroof system to  
malfunction.  
śꢀ Regularly remove any accumulated  
dust on the sunroof rail.  
śꢀ Dust accumulated between the  
sunroof and roof panel can make  
noise Open the sunroof and remove  
dust regularly using a clean cloth.  
śꢀ Do not try to open the sunroof when  
the temperature is below freezing  
or when the sunroof is covered  
with snow or ice. The sunroof may  
not work properly and may break if  
opened by force.  
OTM050029  
In some circumstances resetting the  
sunroof operation may need to be  
performed. Some instances where  
resetting the sunroof may be required  
include:  
-
When the 12-volt battery is either  
disconnected or discharged  
When the sunroof fuse is replaced  
If the sunroof one-touch AUTO OPEN/  
CLOSE operation is not functioning  
properly  
-
-
śꢀ Do not open or drive with the sunroof  
glass open immediately after rain or  
washing the vehicle. Water may wet  
the interior of the vehicle.  
śꢀ Do not extend any luggage outside  
the sunroof while driving. Vehicle  
damage may occur if the vehicle  
suddenly stops.  
WARNING  
Do not extend your head, arms, body  
parts or objects outside the sunroof  
while driving. Injuries may occur if the  
vehicle suddenly stops.  
5-65  
Convenience features  
Sunroof resetting procedure:  
Sunroof open warning  
1. It is recommended to perform the  
reset procedure with the vehicle  
engine running. Start the vehicle in P  
(Park).  
2. Make sure the power sunshade and  
sunroof glass are in the fully closed  
position. If the power sunshade  
and sunroof glass are open, push  
the switch forward until the power  
sunshade and sunroof glass are fully  
closed.  
OTM048118  
3. Release the switch when the power  
sunshade and sunroof glass are fully  
closed.  
4. Push the switch forward until the  
power sunshade and sunroof glass  
move slightly. Then release the switch.  
If the driver turns off the engine when  
the sunroof is not fully closed, the  
warning chime will sound for several  
seconds and the sunroof open warning  
will appear on the cluster LCD display.  
Close the sunroof securely when leaving  
your vehicle.  
5. Once again push and hold the sunroof  
switch forward until the power  
sunshade and sunroof glass slide open  
and close. Do not release the switch  
until the operation is completed.  
CAUTION  
Make sure the sunroof is closed fully  
when leaving your vehicle.  
If the sunroof is left open, rain or snow  
may wet the interior of the vehicle.  
If you release the switch during  
operation, start the procedure again  
from step 2.  
Also, leaving the sunroof open when the  
vehicle is unattended may invite theft.  
Information  
If the sunroof is not reset when the vehicle  
battery is disconnected or discharged, or  
the sunroof fuse is blown, the sunroof may  
not operate normally.  
5-66  
05  
EXTERIOR FEATURES  
Closing the hood  
1. Before closing the hood, check in and  
around the engine compartment to  
ensure the following:  
Hood  
Opening the hood  
-
-
-
Any tools or other loose objects  
are removed from the engine room  
area or hood opening area  
All glove, rags, or other  
combustible material is removed  
from the engine compartment  
All filler caps are tightly and  
correctly installed  
2. Lower the hood halfway (lifted  
approximately 12 in. (30 cm) from the  
closed position) and push down to  
securely lock in place. Then double  
check to be sure the hood is secure.  
If the hood can be raised slightly, it is  
not securely locked. Open it again and  
close it with more force.  
OTM050032  
1. Park the vehicle and set the parking  
brake.  
2. Pull the release lever to unlatch the  
hood. The hood should pop open  
slightly.  
WARNING  
śꢀ Before closing the hood, ensure  
all obstructions are removed from  
around the hood opening.  
śꢀ Always double check to be sure that  
the hood is firmly latched before  
driving away. Check there is no  
hood open warning light or message  
displayed on the instrument cluster.  
Driving with the hood opened may  
cause a total loss of visibility, which  
might result in an accident.  
śꢀ Do not move the vehicle with the  
hood in the raised position, as vision  
is obstructed, which might result in  
an accident, and the hood could fall  
or be damaged.  
OTM050069  
3. Go to the front of the vehicle, raise the  
hood slightly, push up the secondary  
latch (1) inside of the hood center and  
lift the hood.  
After the hood has been lifted halfway,  
it will raise completely by itself.  
5-67  
Convenience features  
Closing the liftgate  
Liftgate  
Opening the liftgate  
OTMPH051004N  
OTM050047  
Lower the liftgate lid and press down  
until it locks. To be sure the liftgate lid is  
securely fastened, always check by trying  
to pull it up again without pressing the  
liftgate handle button.  
Make sure the vehicle is in P (Park) and  
set the parking brake.  
Then do one of the following:  
1. Unlock all doors with the Door Unlock  
button on your remote key or smart  
key. Press the liftgate handle button  
and open the liftgate.  
2. Press and hold the liftgate open  
button on the remote key or smart  
key. Press the liftgate handle button  
and open the liftgate.  
WARNING  
Always keep the liftgate lid completely  
closed while the vehicle is in motion. If  
it is left open or ajar, poisonous exhaust  
gases containing carbon monoxide  
(CO) may enter the vehicle and serious  
illness or death may result.  
3. With the Smart Key in your  
possession, press the liftgate handle  
button and open the liftgate.  
NOTICE  
To prevent damage to the liftgate lift  
cylinders and the attached hardware,  
always close the liftgate before driving.  
Information  
In cold and wet climates, liftgate lock  
and liftgate mechanisms may not work  
properly due to freezing conditions.  
5-68  
05  
Emergency liftgate safety release  
WARNING  
OTMPH051006N  
OTM050041  
Your vehicle is equipped with the  
Do not hold the part (gas lifter) that  
supports the liftgate. Be aware that  
the deformation of the part may cause  
vehicle damage and a risk of injury.  
emergency liftgate safety release lever  
located on the bottom of the liftgate.  
When someone is inadvertently locked  
in the luggage compartment. The liftgate  
can be opened by doing as follows:  
WARNING  
1. Remove the cover.  
2. Push the release lever to the right by  
a key.  
śꢀ NEVER allow anyone to occupy the  
luggage compartment of the vehicle  
at any time. If the liftgate is partially  
or totally latched and the person  
is unable to get out, serious injury  
or death could occur due to lack  
of ventilation, exhaust fumes and  
rapid heat build-up, or because of  
exposure to cold weather conditions.  
The luggage compartment is also  
a highly dangerous location in the  
event of a crash because it is not a  
protected occupant space but is a  
part of the vehicle’s crush zone.  
śꢀ Your vehicle should be kept locked  
and keys should be kept out of  
the reach of children. Parents  
should teach their children about  
the dangers of playing in luggage  
compartments.  
3. Push up the liftgate.  
WARNING  
śꢀ For emergencies, be fully aware  
of the location of the emergency  
liftgate safety release lever in the  
vehicle and how to open the liftgate  
if you are accidentally locked in the  
luggage compartment.  
śꢀ No one should be allowed to occupy  
the luggage compartment of the  
vehicle at any time. The luggage  
compartment is a very dangerous  
location in the event of a crash.  
śꢀ Use the release lever for  
emergencies only. Use with extreme  
caution, especially while the vehicle  
is in motion.  
5-69  
Convenience features  
NOTICE  
Power Liftgate (if equipped)  
Power liftgate operating conditions  
śꢀ Do not close or open the liftgate  
manually. This may cause damage to  
the power liftgate. If it is necessary  
to close or open the liftgate manually  
when the battery is discharged or  
disconnected, do not apply excessive  
force.  
śꢀ Do not operate the power liftgate  
more than 10 times continuously  
when the engine is not running. Use  
the power liftgate with the engine  
running when the power liftgate is  
used repeatedly to prevent battery  
discharge.  
The power liftgate operates when  
the gear is in P (Park) with the engine  
running. However, the power liftgate will  
operate regardless of the gear position  
when the engine is off. Also, the liftgate  
can be opened only when vehicle speed  
is below 1.8 mph (3 km/h).  
For safety, before attempting to open or  
close the liftgate, make sure the vehicle  
is in P (Park).  
WARNING  
śꢀ Do not leave the power liftgate open  
for a long period of time. This may  
drain the battery.  
śꢀ Do not apply excessive force when  
the power liftgate is operating. Doing  
so could result in vehicle damage.  
śꢀ Never leave children or animals  
unattended in your vehicle. Children  
may operate the power liftgate.  
Doing so can result in injury to  
themselves or others and can  
damage the vehicle.  
śꢀ  
śꢀ  
OTM050046  
OTM050046  
Make sure that there are no people  
or objects in the path of the power  
liftgate or smart liftgate prior to  
use. Serious injury, damage to the  
vehicle or damage to surrounding  
objects (for example, walls, ceilings,  
vehicles, etc.) may result if contact  
with the liftgate occurs.  
Do not grab or hold on to the liftgate  
support struts at any time. Damage  
to the liftgate support struts could  
result. Deformation of the liftgate  
support struts may cause vehicle  
damage and personal injury may  
occur.  
5-70  
05  
śꢀ Do not modify or repair any part  
of the power liftgate by yourself.  
This must be done by an authorized  
HYUNDAI dealer.  
śꢀ Do not operate the power liftgate  
under the following conditions.  
The power liftgate may not operate  
properly.  
Information  
śꢀ If the liftgate is not fully closed and  
vehicle speed is at or above 3 km/h (1.8  
mph), a warning will sound 10 times.  
Immediately park the vehicle at a safe  
place, close the liftgate, and check  
that the liftgate open warning on the  
instrument cluster is turned off.  
- One side of the vehicle is lifted to  
inspect the vehicle or change a tire  
- Parking on an uneven road such as  
a slope, etc.  
śꢀ In cold and wet climates, the outside  
power liftgate open/close button may  
not work properly due to freezing  
conditions. If this occurs, remove the  
ice before using the outside power  
liftgate open/close button or use the  
power liftgate open/close button on the  
smart key or the instrument panel.  
śꢀ Close the liftgate completely and  
lock all doors and liftgate using the  
central door lock button before using  
an automatic car wash.  
śꢀ Operating the power liftgate more  
than 5 times continuously could cause  
damage to the operating motor. If  
this occurs, the power liftgate will not  
operate to prevent the motor from  
overheating. If any of the power liftgate  
buttons are pressed to try to open the  
liftgate, the chime will sound 3 times,  
but the liftgate will remain closed.  
Allow the power liftgate system to cool  
for about 1 minute before operating the  
system again.  
śꢀ Do not spray high pressure water  
directly on the power liftgate outside  
open/close button. The liftgate may  
open unintentionally.  
5-71  
Convenience features  
Operating the power liftgate  
OTM050036  
Power liftgate open/close button (Outside  
the power liftgate)  
OTM050046  
When the liftgate is closed, press the  
power liftgate open/close button to open  
the liftgate.  
If the vehicle is locked, press the power  
liftgate open/close button with the smart  
key in your possession.  
If the liftgate is unlocked, the liftgate  
will open or close with a warning sound  
when the power liftgate open/close  
button is pressed without carrying the  
smart key.  
OTM050050  
Power liftgate open/close button (Smart  
key, Instrument panel)  
Press the power liftgate open/close  
button for 1 second. The liftgate opens or  
closes with a warning sound.  
While the liftgate is opening or closing,  
press the button to stop liftgate  
operation.  
If the smart key is not within operation  
range (approximately 10 m) from the  
vehicle, liftgate operation will stop with a  
warning sound for 5 seconds.  
OTMPH051007N  
Power liftgate open/close button (Inside  
the power liftgate)  
Press the power liftgate open/close  
button. The liftgate opens or closes with  
a warning sound.  
5-72  
05  
Automatic reverse  
Setting the power liftgate  
During power liftgate operation if the  
power liftgate senses any obstacle,  
the liftgate will stop or will fully open.  
The automatic reverse feature may  
not operate properly, or it may operate  
unexpectedly under the following  
circumstances:  
To use each feature, you must select the  
opening speed or opening height from  
the settings menu. Deselect the settings  
when you do not want to use the feature.  
Power liftgate opening speed  
To adjust the power liftgate speed,  
VHOHFWꢀœ6HWXSꢀƟꢀ9HKLFOHꢀ6HWWLQJVꢀƟꢀ'RRUꢁ  
/LIWJDWHꢀƟꢀ3RZHUꢀ/LIWJDWHꢀ2SHQLQJꢀ6SHHGꢀ  
Ɵꢀ)DVWꢁ6ORZŔꢀLQꢀWKHꢀLQIRWDLQPHQWꢀV\VWHPꢃꢀ  
(Default setting is ‘Fast.)  
śꢀ The automatic reverse feature may  
not detect the resistance if the  
detected resistance is below a certain  
level, or if the liftgate is almost fully  
closed near the latched position.  
śꢀ The automatic reverse feature may  
operate if a strong impact is applied  
with no obstructions placed.  
User height setting  
1. Position the liftgate manually to the  
height you prefer.  
2. Press the power liftgate open/close  
button located inside the liftgate for  
more than 3 seconds.  
WARNING  
Never intentionally place any object  
or part of your body in the path of  
the power liftgate to make sure the  
automatic reverse feature operates.  
Serious injury, or damage to the vehicle  
or object may occur.  
If ‘User Height Setting’ is selected for  
the power liftgate opening height, the  
power liftgate will automatically open  
to the height manually set by you.  
Information  
Information  
śꢀ If the power liftgate opening height  
has not been manually set, the power  
liftgate will fully open when ‘User  
Height Setting’ from the infotainment  
system is selected.  
śꢀ If one of the height setting (Full Open/  
Level 3/Level 2/Level 1) is selected from  
the settings menu in the infotainment  
system, and then ‘User Height Setting’  
is selected, the liftgate will open to the  
height manually set by you.  
The power liftgate may stop operating if  
the automatic reverse feature operates  
more than two times while attempting to  
open or close the liftgate. If this occurs,  
carefully open or close the liftgate  
manually, and then after 30 seconds try to  
operate the power liftgate automatically  
again.  
śꢀ The power liftgate opening speed  
and opening height settings change  
according to the linked User Profile.  
If the User Profile is changed, power  
liftgate opening speed and opening  
height settings will change accordingly.  
5-73  
Convenience features  
Resetting the power liftgate  
Emergency liftgate safety release  
In some circumstances resetting the  
power liftgate operation may need to  
be performed. Some instances where  
resetting the power liftgate may be  
required include:  
śꢀ When the 12-volt battery is recharged  
śꢀ When the 12-volt battery is reinstalled  
after removal or replacement  
śꢀ When the related fuse is reinstalled  
after removal or replacement  
OTM050042  
To unlock and open the liftgate manually  
from inside the luggage compartment,  
perform the following procedure:  
1. Insert a long, flat object, such as a key  
into the opening at the bottom of the  
liftgate.  
2. Slide the latch in the direction of the  
arrow to unlock the liftgate.  
3. Push the liftgate to open.  
OTMPH051009N  
1. With the engine off or running, put the  
gear in P (Park).  
2. Press the power liftgate open/close  
inner button (A) and outer button (B)  
simultaneously until a chime sounds.  
WARNING  
śꢀ For emergencies, be fully aware  
of the location of the emergency  
liftgate safety release latch in the  
vehicle and how to open the liftgate  
if you are accidentally locked in the  
luggage compartment.  
śꢀ No one, including animals, should  
be allowed to occupy the luggage  
compartment of the vehicle at any  
time. The luggage compartment is a  
very dangerous location in the event  
of an accident.  
3. Slowly close the liftgate manually.  
4. Press the power liftgate open/close  
outer button. The power liftgate will  
open with a chime sound.  
Wait until the liftgate fully opens to  
complete resetting. If the liftgate  
stops before it is fully open, resetting  
cannot be completed.  
śꢀ Use the release latch for  
emergencies only. Use extreme  
caution, especially while the vehicle  
is in motion.  
Information  
If the power liftgate does not operate  
properly after the above procedure, have  
the system inspected by an authorized  
HYUNDAI dealer.  
5-74  
05  
Smart liftgate (if equipped)  
Information  
The smart liftgate will NOT operate when:  
śꢀ A door is not locked or closed.  
śꢀ The smart key is detected within  
15 seconds from when the doors were  
closed and locked.  
śꢀ The smart key is detected within  
15 seconds after the doors are closed  
and locked, and within 60 in. (1.5  
m) from the front door handles. (for  
vehicles equipped with Welcome Light).  
OTMPH051010N  
śꢀ The smart key is in the vehicle.  
On a vehicle equipped with a smart key,  
the liftgate can be opened with hands-  
free activation using the smart liftgate  
system.  
1. Settings  
To activate the Smart Liftgate, go to  
User Settings Mode and select Smart  
Liftgate on the LCD display.  
Using smart liftgate  
The hands-free smart liftgate system  
can be opened automatically when the  
following conditions are met:  
śꢀ The smart liftgate option is enabled in  
the Settings menu in the infotainment  
system screen.  
śꢀ The smart liftgate is activated and  
ready 15 seconds after all the doors  
are closed and locked.  
2. Detect and Alert  
The smart liftgate detecting area  
extends approximately 20~40 in.  
(50~100 cm) behind the vehicle. If you  
are positioned in the detecting area  
and are carrying the smart key, the  
hazard warning lights will blink and  
the chime will sound to alert you that  
the smart liftgate will open.  
śꢀ The smart liftgate will open when  
the smart key is detected in the area  
behind the vehicle for 3 seconds.  
5-75  
Convenience features  
If you press any button on the smart key  
during the Detect and Alert stage, the  
smart liftgate will be deactivated.  
Make sure to be aware of how to  
deactivate the smart liftgate for  
emergency situations.  
Information  
Do not approach the detecting area if you  
do not want the liftgate to open. If you  
have unintentionally entered the detecting  
area and the hazard warning lights and  
chime starts to operate, move away from  
the area behind the vehicle with the smart  
key. The liftgate will remain closed.  
śꢀ If you press the door unlock button  
(2), the smart liftgate will be  
deactivated temporarily. But, if you do  
not open any door for 30 seconds, the  
smart liftgate will be activated again.  
3. Automatic opening  
After the hazard warning lights blink  
and the chime sounds 6 times, the  
smart liftgate will open.  
śꢀ If you press the liftgate open button  
(3) for more than 1 second, the liftgate  
opens.  
śꢀ The smart liftgate will still be activated  
if you press the door lock button (1) or  
liftgate open/close button (3) on the  
smart key as long as the smart liftgate  
is not already in the Detect and Alert  
stage.  
Deactivating smart liftgate  
„Type A  
„Type B  
śꢀ In case you have deactivated the  
smart liftgate by pressing the smart  
key button and opened a door, the  
smart liftgate can be activated again  
by closing and locking all doors.  
OTMA050009  
OTMA050010  
1. Door lock  
2. Door unlock  
3. Liftgate open (Liftgate)  
Liftgate open / close (Power liftgate)  
5-76  
05  
Detecting area  
Fuel filler door  
Opening the fuel filler door  
OTM050060  
śꢀ The smart liftgate detecting area  
extends approximately 20~40 in.  
(50~100 cm) behind the vehicle. If  
you are positioned in the detecting  
area and are carrying the smart key,  
the hazard warning lights will blink  
and the chime will sound for about 3  
seconds to alert you that the liftgate  
will open.  
OTM050063L  
1. Turn the engine off.  
2. Ensure Driver’s door is unlocked.  
3. Press the rear center edge of the fuel  
filler door.  
śꢀ The alert stops once the smart key is  
moved outside of the detecting area  
within the 3 second period.  
Information  
śꢀ Smart liftgate may not operate  
properly if any of the following occur:  
- The smart key is close to a radio  
transmitter such as a radio station or  
an airport which can interfere with  
normal operation of the transmitter.  
OTM048041  
4. Pull the fuel filler door (1) outward to  
access the fuel tank cap.  
5. To remove the fuel tank cap (2), turn  
it counterclockwise. You may hear a  
hissing noise as the pressure inside  
the tank equalizes.  
- The smart key is near a mobile two  
way radio system or a mobile phone.  
- Another vehicle’s smart key is being  
operated close to your vehicle.  
6. Place the cap on the fuel filler door.  
śꢀ Smart liftgate detecting area may  
change when:  
- The vehicle is parked on an incline  
or slope.  
- One side of the vehicle is raised or  
lowered relative to the opposite side.  
5-77  
Convenience features  
Closing the fuel filler door  
Information  
1. To install the fuel tank cap, turn it  
The fuel filler door will unlock when  
clockwise until it “clicks” one time.  
Driver’s door is unlocked.  
To unlock fuel filler door:  
2. Close the fuel filler door until it is  
latched securely.  
śꢀ Press the unlock button on your smart  
key  
Information  
Make the vehicle door to LOCK position  
and the fuel filler door completely closed  
in order to lock the fuel filler door.  
If the fuel filler door is not completely  
closed, the fuel filler door will not be  
locked.  
śꢀ Press the Central Door unlock button  
on armrest trim of driver’s door  
The fuel filler door will lock when Driver’s  
door is locked.  
To lock fuel filler door:  
śꢀ Press the lock button on your smart key  
śꢀ Press the Central Door lock button on  
armrest trim of driver’s door  
CAUTION  
à All doors will automatically lock after  
the vehicle speed exceeds 9 mph. Fuel  
filler door is also locked when vehicle  
speed exceeds 9 mph.  
Keep the door into LOCK position  
when the vehicle is being washed  
(for example, high pressure washer,  
automatic car washer, etc.)  
Information  
WARNING  
If the fuel filler door does not open  
Automotive fuel is highly flammable  
and explosive. Failure to follow these  
guidelines may result in SERIOUS  
INJURY or DEATH:  
because ice has formed around it, tap  
lightly or push on the door to break the  
ice and release the door. Do not pry on the  
door. If necessary, spray around the door  
with an approved deicer fluid (do not use  
radiator antifreeze) or move the vehicle to  
a warm place and allow the ice to melt.  
śꢀ Read and follow all warnings posted  
at the gas station.  
śꢀ Before refueling, note the location  
of the Emergency Fuel Shut-Off, if  
available, at the gas station.  
śꢀ Before touching the fuel nozzle, you  
should eliminate the potential build-  
up of static electricity by touching  
a metal part of the vehicle, a safe  
distance away from the fuel filler  
neck, nozzle, or other gas source,  
with your bare hand.  
śꢀ Do not use mobile phones while  
refueling. Electric current and/or  
electronic interference from cellular  
phones can potentially ignite fuel  
vapors and cause a fire.  
5-78  
05  
śꢀ Do not get back into a vehicle  
once you have begun refueling.  
You can generate a buildup of  
static electricity by touching,  
rubbing or sliding against any item  
or fabric capable of producing  
static electricity. Static electricity  
discharge can ignite fuel vapors  
causing a fire. If you must re-enter  
the vehicle, you should once again  
eliminate potentially dangerous  
static electricity discharge by  
touching a metal part of the vehicle,  
away from the fuel filler neck, nozzle  
or other fuel source, with your bare  
hand.  
śꢀ Do not over-fill or top-off your  
vehicle tank, which can cause fuel  
spillage.  
śꢀ If a fire breaks out during refueling,  
leave the vicinity of the vehicle, and  
immediately contact the manager  
of the gas station and then contact  
the local fire department. Follow any  
safety instructions they provide.  
śꢀ If pressurized fuel sprays out, it can  
cover your clothes or skin and thus  
subject you to the risk of fire and  
burns. Always remove the fuel cap  
carefully and slowly. If the cap is  
venting fuel or if you hear a hissing  
sound, wait until the condition stops  
before completely removing the cap.  
śꢀ When using an approved portable  
fuel container, be sure to place the  
container on the ground prior to  
refueling. Static electricity discharge  
from the container can ignite fuel  
vapors causing a fire.  
śꢀ Always check that the fuel cap is  
installed securely to prevent fuel  
spillage in the event of an accident.  
Once refueling has begun, contact  
between your bare hand and the  
vehicle should be maintained until  
the filling is complete.  
Information  
Make sure to refuel your vehicle according  
to the “Fuel Requirements” section in  
suggested in chapter 1.  
śꢀ Use only approved portable plastic  
fuel containers designed to carry and  
store fuel.  
NOTICE  
śꢀ Do not spill fuel on the exterior  
surfaces of the vehicle. Any type of  
fuel spilled on painted surfaces may  
damage the paint.  
śꢀ When refueling, always shift the  
gear to the P (Park) position, set  
the parking brake, and press the  
Engine Start/Stop button to the  
OFF position. Sparks produced by  
electrical components related to the  
engine can ignite fuel vapors causing  
a fire.  
śꢀ Do not use matches or a lighter and  
do not smoke or leave a lit cigarette  
in your vehicle while at a gas station,  
especially during refueling.  
śꢀ If the fuel filler cap requires  
replacement, use only a genuine  
HYUNDAI cap or the equivalent  
specified for your vehicle. An  
incorrect fuel filler cap can result  
in a serious malfunction of the fuel  
system or emission control system.  
5-79  
Convenience features  
+($'ǘ83ꢀ',63/$<ꢀǣ+8'Ǥꢀǣ,)ꢀ(48,33('Ǥ  
Head-up display information  
OTMA050019  
The Head-Up Display is an optional  
OTMA050016  
feature that allows the driver to view  
information projected onto a transparent  
screen while still keeping your eyes  
safely on the road ahead while driving.  
1. Turn by Turn (TBT) navigation  
2. Traffic  
3. Speedometer  
4. SCC set speed  
Head-up display settings  
5. SCC Vehicle distance  
6. Highway Driving Assist  
7. Lane Following Assist  
8. Lane Safety  
9. Blind-Spot Safety  
10. Highway Auto Speed Change  
Information  
If you select Turn By Turn (TBT)  
navigation information as Head-Up  
Display contents, the Turn By Turn  
(TBT) navigation information will not be  
displayed in the instrument cluster LCD  
display.  
OIK047152N  
śꢀ Head-up display can be enabled from  
the Settings menu in the User Settings  
mode on the instrument cluster LCD  
display. Select:  
- 6HWXSꢀƟꢀ+HDGꢄ8Sꢀ'LVSOD\ꢀƟꢀ(QDEOHꢀ  
Head-Up Display  
śꢀ After turning on the head-up  
display, you can change the settings  
of ‘Display Height’ and ‘Content  
Selection’ of the Head-Up Display.  
5-80  
05  
śꢀ For your safety, make sure to stop the  
Precautions while using the  
head-up display  
śꢀ It may sometimes be difficult to read  
information on the Head-Up Display in  
the following situations.  
vehicle before adjusting the settings.  
śꢀ Do not tint the front windshield glass  
or add other types of metallic coating.  
Otherwise, the Head-Up Display  
image may be invisible.  
śꢀ Do not place any accessories on the  
crash pad or attach any objects on the  
windshield glass.  
śꢀ When replacing the front windshield  
glass, replace it with a windshield  
glass designed for Head-Up Display  
operation. Otherwise, duplicated  
images may be displayed on the  
windshield glass.  
- The driver is improperly positioned  
in the driver’s seat  
- The driver wears polarizing-filter  
sunglasses  
- An object is located above the  
head-up display cover  
- The vehicle is driven on a wet road  
- Any improper lighting accessory is  
installed inside the vehicle, or there  
is incoming light from outside of the  
vehicle  
- The driver wears glasses  
- The driver wears contact lenses  
WARNING  
Blind-Spot Collision Warning  
warnings on the Head-Up Display are  
supplemental. Do not solely depend on  
them to change lanes. Always take a  
look around before changing lanes.  
When it is difficult to read the Head-  
Up Display information, adjust the  
image height or brightness level from  
the Settings menu in the infotainment  
system screen.  
5-81  
Convenience features  
LIGHTING  
Exterior lights  
Lighting control  
To operate the lights, turn the knob at  
the end of the control lever to one of the  
following positions:  
OTM050098  
AUTO headlight  
The position lamp and headlight will  
be turned ON or OFF automatically  
depending on the amount of daylight as  
measured by the ambient light sensor (1)  
at the upper end of the windshield glass.  
OAD045402  
1. OFF  
2. AUTO headlight  
3. Position lamp  
Even with the AUTO headlight feature  
in operation, it is recommended to  
manually turn ON the headlights when  
driving at night or in a fog, driving in the  
rain, or when you enter dark areas, such  
as tunnels and parking facilities.  
4. Headlight  
Daytime Running Light (DRL)  
The Daytime Running Lights (DRL) can  
make it easier for others to see the front  
of your vehicle during the day, especially  
after dawn and before sunset.  
NOTICE  
śꢀ Do not cover or spill anything on the  
sensor (1) located at the upper end of  
the windshield glass.  
śꢀ Do not clean the sensor using  
a window cleaner, the cleanser  
may leave a light film which could  
interfere with sensor operation.  
śꢀ If your vehicle has window tint or  
other types of metallic coating on the  
front windshield, the AUTO headlight  
system may not work properly.  
The DRL system will turn the dedicated  
lamp OFF when :  
śꢀ The headlights are ON.  
śꢀ The parking brake is applied.  
śꢀ The vehicle is turned off.  
5-82  
05  
High beam operation  
OIG046412  
Position lamp (  
)
OOS047407N  
The position lamp, license plate lamp  
and instrument panel lamp are turned  
ON.  
To turn on the high beam headlight, push  
the lever away from you. The lever will  
return to its original position.  
The high beam indicator will light when  
the headlight high beams are switched  
on.  
To turn off the high beam headlight, pull  
the lever towards you. The low beams  
will turn on.  
OIG046413  
Headlight (  
)
The headlight, position lamp, license  
plate lamp and instrument panel lamp  
are turned ON.  
OIG046414  
Information  
To flash the high beam headlight, pull the  
lever towards you, then release the lever.  
The high beams will remain ON as long  
as you hold the lever towards you.  
The ignition switch must be in the ON  
position to turn on the headlight.  
5-83  
Convenience features  
Turn signals and lane change signals  
Battery saver function  
The purpose of this feature is to prevent  
the battery from being discharged.  
The system automatically turns off the  
position lamp when the driver turns the  
vehicle off and opens the driver-side  
door.  
With this feature, the position lamps will  
turn off automatically if the driver parks  
on the side of road at night.  
However, the position lamps stay ON  
even when the driver-side door is opened  
if the headlight switch is turned to the  
position lamp or AUTO (if equipped)  
position after the engine is turned off.  
If necessary, to keep the lamps on  
turn the position lamps OFF and ON  
again using the headlight switch on  
the steering column after the engine is  
turned off.  
OIG046417  
To signal a turn, push down on the lever  
for a left turn or up for a right turn in  
position (A).  
If an indicator stays on and does not flash  
or if it flashes abnormally, one of the turn  
signal bulbs may be burned out and will  
require replacement.  
One touch turn signal  
To use One Touch Turn Signal push the  
turn signal lever up or down to position  
(B) and then release it.  
The lane change signals will blink 3, 5 or  
7 times.  
You can enable the One Touch Turn  
Signal function or choose the number  
RIꢀEOLQNLQJꢀE\ꢀVHOHFWLQJꢀœ6HWXSꢀƟꢀ8VHUꢀ  
6HWWLQJVꢀƟꢀ/LJKWVꢀƟꢀ2QHꢀ7RXFKꢀ7XUQꢀ6LJQDOꢀ  
Ɵꢀ2IIꢁꢅꢀIODVKHVꢁꢆꢀIODVKHVꢁꢇꢀIODVKHVŔꢀLQꢀWKHꢀ  
instrument panel LCD cluster.  
5-84  
05  
Headlight delay function  
(if equipped)  
Traffic change (if equipped)  
The low beam light distribution is  
asymmetric. If you go abroad to a  
country with opposite traffic direction,  
this asymmetric part will dazzle  
oncoming car driver.  
To prevent dazzle, ECE regulation  
demand several technical solutions (ex.  
automatic change system, adhesive  
sheet, down aiming). These headlights  
are designed not to dazzle opposite  
drivers.  
You can activate or deactivate the Traffic  
Change feature from the User Settings  
PRGHꢀRQꢀWKHꢀ/&'ꢀGLVSOD\ꢃꢀ*RꢀWRꢀœ/LJKWVꢀƟꢀ  
Travel Mode.  
If you place the ignition switch to the  
ACC position or the OFF position with  
the headlights ON, the headlights (and/  
or position lamps) remain on for about  
5 minutes. However, if the driver’s door  
is opened and closed, the headlights  
are turned off after 15 seconds. Also,  
with the vehicle off if the driver’s door is  
opened and closed, the headlights (and/  
or position lamps) are turned off after 15  
seconds.  
The headlights (and/or position lamps)  
can be turned off by pressing the lock  
button on the remote key or smart key  
twice or turning the headlight switch to  
the OFF or AUTO position.  
For more details, refer to “LCD Display”  
In chapter 4.  
You can enable the headlight delay  
IXQFWLRQꢀE\ꢀVHOHFWLQJꢀœ6HWXSꢀƟꢀ8VHUꢀ  
6HWWLQJVꢀƟꢀ/LJKWVꢀƟꢀ+HDGOLJKWꢀ'HOD\ꢃ  
NOTICE  
If the driver exits the vehicle through  
another door besides the driver  
door, the battery saver function  
does not operate and the headlight  
delay function does not turn OFF  
automatically.  
This may cause the battery to  
discharge. To avoid battery discharge,  
turn OFF the headlights manually from  
the headlight switch before exiting the  
vehicle.  
5-85  
Convenience features  
+,*+ꢀ%($0ꢀ$66,67ꢀǣ+%$Ǥꢀ  
NOTICE  
Always keep the front view camera in  
good condition to maintain optimal  
performance of High Beam Assist.  
For more details on the precautions  
of the front view camera, refer to  
“Forward Collision-Avoidance Assist  
(FCA)” section in chapter 7.  
High Beam Assist Settings  
OIK047090  
:LWKꢀWKHꢀHQJLQHꢀRQꢈꢀVHOHFWꢀœ/LJKWVꢀƟꢀ+LJKꢀ  
Beam Assist (or HBA (High Beam Assist))’  
from the Settings menu to turn on High  
Beam Assist and deselect to turn off the  
system.  
High Beam Assist will automatically  
adjust the headlight range (switches  
between high beam and low beam)  
depending on the brightness of detected  
vehicles and certain road conditions.  
WARNING  
For your safety, change the Settings  
after parking the vehicle at a safe  
location.  
Detecting sensor (Front view  
camera)  
OTM070001  
[1] : Front view camera  
The front view camera is used as a  
detecting sensor to detect ambient light  
and brightness while driving.  
Refer to the picture above for the  
detailed location of the detecting sensor.  
5-86  
05  
śꢀ When High Beam Assist is operating,  
High Beam Assist Operation  
high beam switches to low beam if  
any of the following conditions occur:  
Display and control  
śꢀ After selecting ‘High Beam Assist’  
in the Settings menu, High Beam  
Assist will operate by following the  
procedure below.  
- When the headlight of an oncoming  
vehicle is detected.  
- When the tail lamp of a vehicle in  
front is detected.  
- When the headlight or tail lamp of a  
motorcycle or a bicycle is detected.  
- When the surrounding ambient light  
is bright enough that high beams  
are not required.  
- Place the headlight switch in  
the AUTO position and push  
the headlight lever towards the  
instrument cluster. The High Beam  
Assist ( ) indicator light will  
illuminate on the cluster and the  
system will be enabled.  
- When the system is enabled, high  
beam will turn on when vehicle  
speed is above 25mph (40km/h).  
When vehicle speed is below 15mph  
(25km/h), high beam will not turn  
on.  
- When streetlights or other lights are  
detected.  
High Beam Assist Malfunction  
and Limitations  
High Beam Assist Malfunction  
„Type A  
„Type B  
- The High Beam (  
) indicator light  
will illuminate on the cluster when  
high beam is on.  
śꢀ When High Beam Assist is operating,  
if the headlight lever or switch is used,  
the system operates as follow:  
- If the headlight lever is pulled  
towards you when the high beam  
is off, the high beam will turn on  
without High Beam Assist canceled.  
When you let go of the headlight  
lever, the lever will move to the  
middle and the high beam will turn  
off.  
- If the headlight lever is pulled  
towards you when the high beam is  
on by High Beam Assist, low beam  
will be on and the system will turn  
off.  
OTM050218N  
OTM050218L  
When High Beam Assist is not working  
properly, the ‘Check High Beam Assist  
(HBA) system’ or ‘Check HBA (High  
Beam Assist system’ warning message  
will appear and warning light will  
illuminate on the cluster. Have the  
system be inspected by an authorized  
HYUNDAI dealer.  
- If the headlight switch is placed  
from AUTO to another position  
(headlight/position/off), High  
Beam Assist will turn off and the  
corresponding lamp will turn on.  
5-87  
Convenience features  
Limitations of High Beam Assist  
High Beam Assist may not work properly  
in the following situations:  
śꢀ Light from a vehicle is not detected  
because of lamp damage, or because  
it is hidden from sight, etc.  
WARNING  
śꢀ At times, High Beam Assist may not  
work properly. It is the responsibility  
of the driver for safe driving  
practices and always check the road  
conditions for your safety.  
śꢀ Headlight of a vehicle is covered with  
śꢀ When High Beam Assist does not  
operate normally, change the  
headlight position manually between  
high beam and low beam.  
dust, snow or water.  
śꢀ A vehicle’s headlights are off but the  
fog lamps are on and etc.  
śꢀ There is a lamp that has a similar  
shape as a vehicle’s lamp.  
śꢀ Headlights have been damaged or not  
repaired properly.  
śꢀ Headlights are not aimed properly.  
śꢀ Driving on a narrow curved road,  
rough road, uphill or downhill.  
śꢀ Vehicle in front is partially visible on a  
crossroad or curved road.  
śꢀ There is a traffic light, reflecting sign,  
flashing sign or mirror ahead.  
śꢀ There is a temporary reflector or flash  
ahead (construction area).  
śꢀ The road conditions are bad such as  
being wet, iced or covered with snow.  
śꢀ A vehicle suddenly appears from a  
curve.  
śꢀ The vehicle is tilted from a flat tire or  
is being towed.  
śꢀ Light from a vehicle is not detected  
because of exhaust fume, smoke, fog,  
snow, etc.  
For more details on the limitations  
of the front view camera, refer to  
“Forward Collision-Avoidance Assist  
(FCA)” section in chapter 7.  
5-88  
05  
INTERIOR LIGHTS  
Front lamps  
WARNING  
Do not use the interior lights when  
driving in the dark. The interior lights  
may obscure your view and cause an  
accident.  
NOTICE  
Do not use the interior lights for  
extended periods when the vehicle is  
turned off or the battery will discharge.  
OTM050227L  
Interior lamp AUTO cut  
Front map lamp (  
):  
The interior lamps will automatically go  
off approximately 10 minutes after the  
vehicle is turned off and the doors are  
closed. If a door is opened, the lamp  
will go off 40 minutes after the vehicle  
is turned off. If the doors are locked by  
the smart key and the vehicle enters the  
armed stage of the theft alarm system,  
the lamps will go off five seconds later.  
Touch either icons to turn the map lamp  
on or off. This light produces a spot  
beam for convenient use as a map lamp  
at night or as a personal lamp for the  
driver and the front passenger.  
Door lamp (  
):  
The front or rear room lamps come on  
when the front or rear doors are opened.  
When doors are unlocked by the smart  
key, the front and rear lamps come on  
for approximately 30 seconds as long as  
any door is not opened. The front and  
rear room lamps go out gradually after  
approximately 30 seconds when the  
door is closed. However, if the Engine  
Start/Stop button is in the ON position  
or all doors are locked, the front and rear  
lamps will turn off. If a door is opened  
with the ignition switch in the ACC  
position or the OFF position, the front  
and rear lamps will stay on for about 10  
minutes.  
Room lamp (  
)
Press the button to turn ON the room  
lamp for the front/rear seats.  
5-89  
Convenience features  
Rear lamps  
Vanity mirror lamp  
„Type A  
OTM048076  
OTM050200  
„Type B  
Push the switch to turn the light on or off.  
śꢀ  
: The lamp will turn on if this  
button is pressed.  
śꢀ  
: The lamp will turn off if this  
button is pressed.  
OTM048409  
Rear room lamp switch :  
Press this button to turn the room lamp  
on and off.  
5-90  
05  
Luggage compartment lamp  
Puddle lamp  
OTMPH051012N  
OTM050080  
śꢀ ON : The luggage compartment lamp  
Welcome light  
stays on at all times.  
When all doors (and liftgate) are closed  
and locked, the puddle lamp will turn on  
for 15 seconds if the door is unlocked by  
the smart key or when you put your hand  
in the outside door handle with the smart  
key in possession.  
śꢀ DOOR : The luggage compartment  
lamp comes on when the liftgate is  
opened.  
śꢀ OFF : The luggage compartment lamp  
is off.  
For more details, refer to “Welcome  
System” in this chapter.  
Escort light  
When the Engine Start/Stop button is in  
the OFF position and the driver’s door is  
opened, the puddle lamp will turn on for  
30 seconds. If the driver’s door is closed  
within the 30 second period, the puddle  
lamp will turn off after 15 seconds. If the  
driver’s door is closed and locked, the  
puddle lamp will turn off immediately.  
The Puddle Lamp Escort Light will turn  
on only the first time the driver’s door is  
opened after the engine is turned off.  
5-91  
Convenience features  
Headlight and position lamp  
Welcome system  
When the headlight (lamp switch in the  
headlight or AUTO position) is on and  
all doors (and liftgate) are locked and  
closed, the position lamp and headlight  
will come on for 15 seconds when the  
door unlock button is pressed on the  
remote key or smart key.  
At this time, if you press the door lock  
or unlock button, the position lamp and  
headlight will turn off immediately.  
OTM050075  
Interior lamp  
Welcome system helps keep the driver  
visible by turning on vehicle lights when  
the driver approaches the vehicle.  
When the interior lamp switch is in the  
position and all doors (and liftgate)  
are closed and locked, the room lamp  
will come on for 30 seconds if any of the  
below is performed.  
Puddle lamp and door handle lamp  
-
When the door unlock button is  
pressed on the remote key or smart  
key.  
When you put your hand in the  
outside door handle while carrying the  
smart key.  
When all the doors (and liftgate) are  
closed and locked, the puddle lamp  
and door handle lamp will turn on for  
approximately 15 seconds if any of the  
below is performed.  
1. ,Iꢀœ&RQYHQLHQFHꢀƟꢀ:HOFRPHꢀPLUURUꢁ  
OLJKWꢀƟꢀ2QꢀGRRUꢀXQORFNŔꢀLVꢀVHOHFWHGꢀLQꢀ  
the User Settings mode on the LCD  
display,  
-
At this time, if you press the door lock  
or unlock button on the smart key the  
lamps will turn off immediately.  
śꢀthe lamps will turn on when the  
door lock button is pressed on the  
smart key.  
śꢀthe lamps will turn on when the  
button of the outside door handle  
is pressed with the smart key in  
possession.  
2. ,IꢀERWKꢀœ&RQYHQLHQFHꢀƟꢀ:HOFRPHꢀ  
PLUURUꢁOLJKWꢀƟꢀ2QꢀGRRUꢀXQORFNŔꢀDQGꢀ  
œ&RQYHQLHQFHꢀƟꢀ:HOFRPHꢀPLUURUꢁOLJKWꢀ  
Ɵꢀ2QꢀGULYHUꢀDSSURDFKŔꢀLVꢀVHOHFWHGꢀLQꢀ  
the User Settings mode on the LCD  
display, the lamps will turn on when  
the vehicle is approached with the  
smart key in possession.  
You can activate or deactivate Welcome  
Light function from the User Settings  
mode on the LCD display.  
5-92  
05  
:,3(56ꢀ$1'ꢀ:$6+(56  
„Front windshield wiper/washer  
Windshield wipers  
Operates as follows when the ignition  
switch is turned ON.  
MIST :  
For a single wiping cycle,  
move the lever upward and  
release it. The wipers will  
operate continuously if the  
lever is held in this position.  
OFF :  
INT :  
Wipers are not in operation.  
Wipers operate intermittently  
at the same wiping intervals.  
Use this mode in light rain  
or mist. To vary the speed  
setting, turn the speed  
control knob.  
OTLE045161  
„Rear windshield wiper/washer  
LO :  
HI :  
The wiper runs at a lower speed.  
The wiper runs at a higher speed.  
Information  
If there is heavy accumulation of snow  
or ice on the windshield, defrost the  
windshield for about 10 minutes, or until  
the snow and/or ice is removed before  
using the windshield wipers to ensure  
proper operation.  
OTLE045508  
A. Wiper speed control (front)  
śꢀMIST – Single wipe  
śꢀOFF – Off  
If you do not remove the snow and/or ice  
before using the wiper and washer, it may  
damage the wiper and washer system.  
śꢀINT – Intermittent wipe  
AUTO* – Auto control wipe  
śꢀLO– Low wiper speed  
śꢀHI – High wiper speed  
B. Intermittent control wipe time  
adjustment  
C. Wash with brief wipes (front)  
(pull lever towards you)  
D. Rear wiper control*  
śꢀHI – High wiper speed  
śꢀLO– Low wiper speed  
śꢀOFF – Off  
E. Wash with brief wipes (rear)  
(pull lever towards you)  
* : if equipped  
5-93  
Convenience features  
AUTO (Automatic) control  
(if equipped)  
The rain sensor located on the upper  
end of the windshield glass senses  
the amount of rainfall and controls the  
wiping cycle for the proper interval.  
The wiper operation time will be  
automatically controlled depends on  
rainfall.  
When the rain stops, the wiper stops.  
To vary the sensitivity setting, turn the  
sensitivity control knob.  
If the wiper switch is set in AUTO mode  
when the Engine Start/Stop button is in  
the ON position, the wiper will operate  
once to perform a self-check of the  
system. Set the wiper to the OFF (O)  
position when the wiper is not in use.  
WARNING  
To avoid personal injury from the  
windshield wipers, when the engine  
is running and the windshield wiper  
switch is placed in the AUTO mode:  
śꢀ Do not touch the upper end of the  
windshield glass facing the rain  
sensor.  
śꢀ Do not wipe the upper end of the  
windshield glass with a damp or wet  
cloth.  
śꢀ Do not put pressure on the  
windshield glass.  
NOTICE  
śꢀ When washing the vehicle, set the  
wiper switch in the OFF (O) position  
to stop the auto wiper operation. The  
wiper may operate and be damaged  
if the switch is set in the AUTO mode  
while washing the vehicle.  
śꢀ Do not remove the sensor cover  
located on the upper end of the  
passenger side windshield glass.  
Damage to system components  
could occur and may not be covered  
by your vehicle warranty.  
śꢀ Because of using a photo sensor,  
temporary malfunction could occur  
according to sudden ambient light  
change made by stone and dust  
while driving.  
5-94  
05  
Front windshield washers  
WARNING  
When the outside temperature is below  
freezing, ALWAYS warm the windshield  
using the defroster to help prevent  
the washer fluid from freezing on the  
windshield and obscuring your vision  
which could result in an accident and  
serious injury or death.  
NOTICE  
śꢀ To prevent possible damage to the  
washer pump, do not operate the  
washer when the fluid reservoir is  
empty.  
śꢀ To prevent possible damage to the  
wipers or windshield, do not operate  
the wipers when the windshield is  
dry.  
śꢀ To prevent damage to the wiper  
arms and other components, do  
not attempt to move the wipers  
manually.  
OTLE045164  
In the OFF position, pull the lever gently  
toward you to spray washer fluid on the  
windshield and to run the wipers 1-3  
cycles. The spray and wiper operation  
will continue until you release the lever. If  
the washer does not work, you may need  
to add washer fluid to the washer fluid  
reservoir.  
śꢀ To prevent possible damage to the  
wipers and washer system, use anti-  
freezing washer fluids in the winter  
season or cold weather.  
5-95  
Convenience features  
Auto rear wiper (if equipped)  
Rear window wiper and washer  
The rear wiper will operate while the  
vehicle is in reverse with the front wiper  
ON by selecting the function from the  
Settings menu on the LCD display.  
Select:  
-
6HWXSꢀƟꢀ8VHUꢀ6HWWLQJVꢀƟꢀ&RQYHQLHQFHꢀ  
Ɵꢀ$XWRꢀ5HDUꢀ:LSHUꢀꢉLQꢀ5ꢊ  
OTLE045165  
The rear window wiper and washer  
switch is located at the end of the wiper  
and washer switch lever. Turn the switch  
to the desired position to operate the  
rear wiper and washer.  
HI – High wiper speed  
LO – Low wiper speed  
OFF – Off  
OTLE045166  
Push the lever away from you to spray  
rear washer fluid and to run the rear  
wipers 1~3 cycles. The spray and wiper  
operation will continue until you release  
the lever.  
5-96  
05  
0$18$/ꢀ&/,0$7(ꢀ&21752/ꢀ6<67(0ꢀǣ,)ꢀ(48,33('Ǥ  
OTM050121L  
1. Fan speed control knob  
2. Temperature control knob  
3. Mode selection button  
6. Air conditioning button  
7. Air intake control button  
4. Front windshield defroster button  
5. Rear window defroster button  
5-97  
Convenience features  
3. Set the temperature control to the  
desired position.  
4. Set the air intake control to the  
outside (fresh) air position.  
5. Set the fan speed control to the  
desired speed.  
6. If air conditioning is desired, turn the  
air conditioning system on.  
Heating and air conditioning  
1. Start the engine.  
2. Set the mode to the desired position.  
To improve the effectiveness of  
heating and cooling, select:  
-
-
Heating:  
Cooling:  
Mode selection (3)  
The actual shape of air conditioner may differ from the illustration.  
OTMA050100  
The mode selection button controls the direction of the air flow through the ventilation  
system.  
5-98  
05  
Floor/Defrost-Level  
(A, C, D, E, F, G)  
Face-Level (B, C, E)  
Air flow is directed toward the upper  
body and face. Additionally, each outlet  
can be controlled to direct the air  
discharged from the outlet.  
Most of the air flow is directed to the  
floor and the windshield with a small  
amount directed to the side window  
defrosters.  
Bi-Level (B, C, D, E, F, G)  
Front defroster (A, D)  
Air flow is directed towards the face and  
the floor.  
Most of the air flow is directed to the  
windshield with a small amount of air  
directed to the side window defrosters.  
A/C MAX-Level (B, D) (if equipped)  
Floor-Level (A, C, D, E, F, G)  
To operate the A/C MAX, turn the  
temperature control knob to extreme  
left. Air flow is directed toward the upper  
body and face.  
In this mode, the air conditioning and the  
recirculated air position will be selected  
automatically.  
Most of the air flow is directed to the  
floor, with a small amount of the air  
being directed to the windshield and side  
window defrosters.  
After the interior has cooled sufficiently,  
whenever possible, move the  
temperature knob away from A/C MAX  
and press the A/C button.  
5-99  
Convenience features  
„Front  
Recirculated air position  
With the recirculated air  
position selected, air from the  
passenger compartment will  
be drawn through the heating  
system and heated or cooled  
according to the function  
selected.  
Outside (fresh) air position  
„Type A  
With the outside (fresh) air  
position selected, air enters  
the vehicle from outside  
and is heated or cooled  
according to the function  
selected.  
OTM050124  
„Rear  
„Type B  
Information  
OTM048308  
Using the system in the fresh air position is  
Instrument panel vents  
recommended.  
The outlet vents can be opened or closed  
separately using the vent control lever.  
If you move the vent control lever to the  
left end, the outlet vents can be closed.  
Prolonged operation of the heater in the  
recirculated air position (without air  
conditioning selected) can cause fogging of  
the windshield and side windows and the  
air within the passenger compartment will  
become stale.  
Temperature control  
In addition, prolonged use of the air  
conditioning with the recirculated air  
position selected will result in excessively  
dry air in the passenger compartment.  
The temperature will increase by turning  
the knob to the right. The temperature  
will decrease by turning the knob to the  
left.  
Air intake control  
This is used to select outside (fresh) air  
position or recirculated air position. To  
change the air intake control position,  
press the control button.  
5-100  
05  
System operation  
Ventilation  
1. Set the mode to the  
2. Set the air intake control to the  
outside (fresh) air position.  
3. Set the temperature control to the  
desired position.  
WARNING  
śꢀ Continued climate control system  
operation in the recirculated air  
position may allow humidity to  
increase inside the vehicle which  
may fog the glass and obscure  
visibility.  
śꢀ Do not sleep in a vehicle with the air  
conditioning or heating system on. It  
may cause serious harm or death due  
to a drop in the oxygen level and/or  
body temperature.  
śꢀ Continued climate control system  
operation in the recirculated air  
position can cause drowsiness  
or sleepiness, and loss of vehicle  
control. Set the air intake control  
to the outside (fresh) air position as  
much as possible while driving.  
position.  
4. Set the fan speed control to the  
desired speed.  
Heating  
1. Set the mode to the  
2. Set the air intake control to the  
outside (fresh) air position.  
3. Set the temperature control to the  
desired position.  
position.  
4. Set the fan speed control to the  
desired speed.  
5. If dehumidified heating is desired,  
Fan speed control  
turn the air conditioning system (if  
equipped) on.  
Turn the knob to the right to increase  
the fan speed and airflow. Turn the knob  
to the left to decrease fan speed and  
airflow.  
If the windshield fogs up, set the mode  
to the  
or  
position.  
Setting the fan speed control knob to the  
“0” position turns off the fan.  
Operation Tips  
śꢀ To help keep dust or unpleasant fumes  
from entering the vehicle through the  
ventilation system, temporarily set the  
air intake control to the recirculated  
air position. Be sure to return the  
NOTICE  
Operating the fan speed when the  
ignition switch is in the ON position  
could cause the battery to discharge.  
Operate the fan speed when the engine  
is running.  
control to the fresh air position when  
the irritation has passed to keep fresh  
air in the vehicle. This will help keep  
the driver alert and comfortable.  
Air conditioning (A/C) (if equipped)  
śꢀ To prevent interior fog on the  
windshield, set the air intake control  
to the fresh air position and fan speed  
to the desired position, turn on the air  
conditioning system, and adjust the  
temperature control to the desired  
temperature.  
Press the A/C button to turn the air  
conditioning system on (indicator light  
will illuminate). Press the button again to  
turn the air conditioning system off.  
5-101  
Convenience features  
Air conditioning system operation tips  
Air conditioning  
śꢀ If the vehicle has been parked in  
direct sunlight during hot weather,  
open the windows for a short time  
to let the hot air inside the vehicle  
escape.  
śꢀ After sufficient cooling has been  
achieved, switch back from the  
recirculated air to the fresh outside air  
position.  
śꢀ To help reduce moisture inside of  
the windows on rainy or humid  
days, decrease the humidity inside  
the vehicle by operating the air  
conditioning system with the windows  
and sunroof closed.  
śꢀ Use the air conditioning system every  
month for a few minutes to ensure  
maximum system performance.  
HYUNDAI Air Conditioning Systems are  
filled with R-1234yf refrigerant.  
1. Start the engine. Push the air  
conditioning button.  
2. Set the mode to the  
position.  
3. Set the air intake control to the  
outside air or recirculated air position.  
4. Adjust the fan speed control and  
temperature control to maintain  
maximum comfort.  
NOTICE  
When using the air conditioning system,  
monitor the temperature gauge closely  
while driving up hills or in heavy traffic  
when outside temperatures are high.  
Air conditioning system operation may  
cause engine overheating. Continue to  
use the fan but turn the air conditioning  
system off if the temperature gauge  
indicates engine overheating.  
śꢀ If you operate the air conditioner  
excessively, the difference between  
the temperature of the outside air and  
that of the windshield could cause  
the outer surface of the windshield to  
fog up, causing loss of visibility. In this  
case, set the mode selection knob to  
the  
position and set the fan speed  
control knob to the lowest speed  
setting.  
5-102  
05  
Checking the amount of air  
conditioner refrigerant and  
compressor lubricant  
System maintenance  
Cabin air filter  
When the amount of refrigerant is low,  
the performance of the air conditioning  
is reduced. Overfilling also reduces the  
performance of the air conditioning system.  
Therefore, if abnormal operation is found,  
have the system be inspected by an  
authorized HYUNDAI dealer.  
NOTICE  
It is important that the correct type and  
amount of oil and refrigerant is used.  
Otherwise, damage to the compressor  
and abnormal system operation may  
occur. To prevent damage, the air  
conditioning system in your vehicle  
should only be serviced by trained and  
certified technicians.  
OIK047401L  
[A] : Outside air, [B] : Recirculated air  
[C] : Cabin air filter, [D] : Blower  
[E] : Evaporator core, [F] : Heater core  
The cabin air filter is installed behind  
the glove box. It filters the dust or other  
pollutants that enter the vehicle through  
the heating and air conditioning system.  
Have the cabin air filter be replaced by  
an authorized HYUNDAI dealer according  
to the maintenance schedule.  
If the vehicle is being driven in severe  
conditions such as dusty or rough roads,  
more frequent climate control filter  
inspections and changes are required.  
If the air flow rate suddenly decreases,  
have the system be checked at an  
authorized HYUNDAI dealer.  
5-103  
Convenience features  
NOTICE  
śꢀ The refrigerant system should only  
be serviced by trained and certified  
technicians to insure proper and safe  
operation.  
śꢀ The refrigerant system should be  
serviced in a well-ventilated place.  
śꢀ The air conditioning evaporator  
(cooling coil) shall never be repaired  
or replaced with one removed from  
a used or salvaged vehicle and new  
replacement MAC evaporators shall  
be certified (and labeled) as meeting  
SAE Standard J2842.  
OTM050040L  
Air Conditioning refrigerant label  
You can find out which air conditioning  
refrigerant is applied to your vehicle on  
the label located inside of the hood.  
WARNING  
Vehicles equipped with R-1234yf  
„Example  
Since the refrigerant is  
mildly flammable and  
operated at high pressure,  
the air conditioning system  
should only be serviced  
by trained and certified  
technicians. It is important  
that the correct type and  
amount of oil and refrigerant  
are used.  
OHYK059001  
All refrigerants should be reclaimed  
with proper equipment.  
Venting refrigerants directly to the  
atmosphere is harmful to individuals  
and environment. Failure to heed these  
warnings can lead to serious injuries.  
Each symbols and specification on  
the air conditioning refrigerant label is  
represented as below:  
1. Classification of refrigerant  
2. Amount of refrigerant  
3. Classification of compressor lubricant  
4. Caution  
5. Flammable refrigerant  
6. To require registered technician to  
service air conditioning system  
5-104  
05  
$8720$7,&ꢀ&/,0$7(ꢀ&21752/ꢀ6<67(0ꢀǣ,)ꢀ(48,33('Ǥ  
The actual shape of air conditioner may differ from the illustration.  
OTMA050101  
1. Driver’s temperature control knob  
2. Passenger’s temperature control knob  
3. AUTO (automatic control) button  
4. Front windshield defroster button  
5. Rear window defroster button  
6. Air conditioning button  
7. SYNC button  
8. OFF button  
9. Fan speed button  
10.Mode selection button  
11. Climate control button  
12.Air intake control button  
5-105  
Convenience features  
Automatic heating and air  
conditioning  
The Automatic Climate Control System  
is controlled by setting the desired  
temperature.  
1. Press the AUTO button. (3)  
The modes, fan speeds, air intake and  
air-conditioning will be controlled  
automatically by the temperature  
setting you select.  
OTM050052  
2. Turn the temperature control knob  
(1, 2) to the desired temperature. If  
the temperature is set to the lowest  
setting (Lo), the air conditioning  
system will operate continuously.  
After the interior has cooled  
Information  
Never place anything near the sensor to  
ensure better control of the heating and  
cooling system.  
sufficiently, adjust the knob to  
a higher temperature set point  
whenever possible.  
Manual heating and air  
conditioning  
To turn the automatic operation off,  
select any button of the following:  
The heating and cooling system can be  
controlled manually by pushing buttons  
other than the AUTO button. In this case,  
the system works sequentially according  
to the order of buttons selected. When  
pressing any button except the AUTO  
button while using automatic operation,  
the functions not selected will be  
-
-
Mode selection button  
Front windshield defroster button  
(Press the button one more time  
to deselect the front windshield  
defroster function. The ‘AUTO’ sign  
will illuminate on the information  
display once again.)  
controlled automatically.  
1. Start the engine.  
-
Fan speed control button  
2. Set the mode to the desired position.  
For improving the effectiveness of  
heating and cooling, select:  
The selected function will be  
controlled manually while other  
functions operate automatically.  
-
-
Heating:  
Cooling:  
For your convenience and to improve  
the effectiveness of the climate control,  
use the AUTO button and set the  
temperature to 73°F (23°C).  
3. Set the temperature control to the  
desired position.  
4. Set the air intake control to the  
outside (fresh) air position.  
5. Set the fan speed control to the  
desired speed.  
6. If air conditioning is desired, turn the  
air conditioning system on.  
7. Press the AUTO button to convert to  
full automatic control of the system.  
5-106  
05  
Mode selection (12)  
The actual shape of air conditioner may differ from the illustration.  
OTMA050100  
The mode selection button controls the direction of the air flow through the ventilation  
system.  
5-107  
Convenience features  
„Front  
Face-Level (B, C, E)  
Air flow is directed toward the upper  
body and face. Additionally, each outlet  
can be controlled to direct the air  
discharged from the outlet.  
Bi-Level (B, C, D, E, F, G)  
OTM050124  
„Rear  
Air flow is directed towards the face and  
the floor.  
Floor-Level (A, C, D, E, F, G)  
Most of the air flow is directed to the  
floor, with a small amount of the air  
being directed to the windshield and side  
window defrosters.  
OTM050201  
Instrument panel vents  
The outlet vents can be opened or closed  
separately using the vent control lever.  
If you move the vent control lever to the  
left end, the outlet vents can be closed.  
Floor/Defrost-Level  
(A, C, D, E, F, G)  
Most of the air flow is directed to the  
floor and the windshield with a small  
amount directed to the side window  
defrosters.  
Defrost-Level (A, D)  
Most of the air flow is directed to the  
windshield with a small amount of air  
directed to the side window defrosters.  
5-108  
05  
Adjusting the driver and passenger side  
Temperature control  
temperature individually  
śꢀ Press the “SYNC” button again to  
adjust the driver and passenger side  
temperature individually. The button  
indicator will turn off.  
Temperature conversion  
If the battery has been discharged or  
disconnected, the temperature mode  
display will reset to Centigrade.  
To change the temperature unit from °C  
to °F or °F to °C :  
OTM050103  
The temperature will increase by pushing  
the knob upward. The temperature  
will decrease by pushing the knob  
downward.  
-
Automatic climate control system  
Press the AUTO button for 3 seconds  
while pressing the OFF button.  
-
Instrument cluster  
*RꢀWRꢀ8VHUꢀ6HWWLQJVꢀ0RGHꢀƟꢀ8QLWVꢀƟꢀ  
Temperature Unit.  
The temperature unit on both the cluster  
LCD display and the climate control  
screen will change.  
OTM050108  
Adjusting the driver and passenger side  
temperature equally  
śꢀ Press the “SYNC” button to adjust  
the driver and passenger side  
temperature equally.  
The passenger side temperature will  
be set to the same temperature as the  
driver side temperature.  
śꢀ Turn the driver side temperature  
control knob. The driver and  
passenger side temperature will be  
adjusted equally.  
5-109  
Convenience features  
Air intake control  
This is used to select the outside (fresh)  
air position or recirculated air position.  
To change the air intake control position,  
push the control button.  
Information  
Using the system in the fresh air position is  
recommended.  
Prolonged operation of the heater in the  
recirculated air position (without air  
conditioning selected) can cause fogging of  
the windshield and side windows and the  
air within the passenger compartment will  
become stale.  
In addition, prolonged use of the air  
conditioning with the recirculated air  
position selected will result in excessively  
dry air in the passenger compartment.  
Recirculated air position  
With the recirculated air  
position selected, air from the  
passenger compartment will  
be drawn through the heating  
system and heated or cooled  
according to the function  
selected.  
WARNING  
Outside (fresh) air position  
„Type A  
śꢀ Continued climate control system  
operation in the recirculated air  
position may allow humidity to  
increase inside the vehicle which  
may fog the glass and obscure  
visibility.  
With the outside (fresh) air  
position selected, air enters  
the vehicle from outside  
and is heated or cooled  
according to the function  
selected.  
„Type B  
śꢀ Do not sleep in a vehicle with the air  
conditioning or heating system on. It  
may cause serious harm or death due  
to a drop in the oxygen level and/or  
body temperature.  
śꢀ Continued climate control system  
operation in the recirculated air  
position can cause drowsiness  
or sleepiness, and loss of vehicle  
control. Set the air intake control  
to the outside (fresh) air position as  
much as possible while driving.  
5-110  
05  
Fan speed control  
The fan speed can be set as desired by  
pushing the fan speed control button.  
More air is delivered with higher fan  
speeds.  
Pressing the OFF button turns off the fan.  
System operation  
Ventilation  
1. Set the mode to the  
2. Set the air intake control to the  
outside (fresh) air position.  
3. Set the temperature control to the  
desired position.  
position.  
NOTICE  
4. Set the fan speed control to the  
desired speed.  
Operating the fan when the ignition  
switch is in the ON position could cause  
the battery to discharge. Operate the  
fan when the engine is running.  
Heating  
1. Set the mode to the  
position.  
2. Set the air intake control to the  
outside (fresh) air position.  
3. Set the temperature control to the  
desired position.  
4. Set the fan speed control to the  
desired speed.  
Air conditioning  
Push the A/C button to turn the air  
conditioning system on (indicator light  
will illuminate).  
Push the button again to turn the air  
conditioning system off.  
5. If dehumidified heating is desired,  
turn the air conditioning system on.  
If the windshield fogs up, set the mode  
OFF mode  
Push the OFF button to turn the climate  
control system off. However, you can still  
operate the mode and air intake buttons  
as long as the ignition switch is in the ON  
position.  
to the  
or  
position.  
Operation Tips  
śꢀ To help keep dust or unpleasant fumes  
from entering the vehicle through the  
ventilation system, temporarily set the  
air intake control to the recirculated  
air position. Be sure to return the  
control to the fresh air position when  
the irritation has passed to keep fresh  
air in the vehicle. This will help keep  
the driver alert and comfortable.  
śꢀ To prevent interior fog on the  
windshield, set the air intake control  
to the fresh air position and fan speed  
to the desired position, turn on the air  
conditioning system, and adjust the  
temperature control to the desired  
temperature.  
5-111  
Convenience features  
Air conditioning system operation tips  
Air conditioning  
śꢀ If the vehicle has been parked in  
direct sunlight during hot weather,  
open the windows for a short time  
to let the hot air inside the vehicle  
escape.  
śꢀ After sufficient cooling has been  
achieved, switch back from the  
recirculated air to the fresh outside air  
position.  
śꢀ To help reduce moisture inside of  
the windows on rainy or humid  
days, decrease the humidity inside  
the vehicle by operating the air  
conditioning system with the windows  
and sunroof closed.  
śꢀ Use the air conditioning system every  
month for a few minutes to ensure  
maximum system performance.  
HYUNDAI Air Conditioning Systems are  
filled with R-1234yf refrigerant.  
1. Start the engine. Push the air  
conditioning button.  
2. Set the mode to the  
position.  
3. Set the air intake control to the  
outside air or recirculated air position.  
4. Adjust the fan speed control and  
temperature control to maintain  
maximum comfort.  
NOTICE  
When using the air conditioning system,  
monitor the temperature gauge closely  
while driving up hills or in heavy traffic  
when outside temperatures are high.  
Air conditioning system operation may  
cause engine overheating. Continue to  
use the fan but turn the air conditioning  
system off if the temperature gauge  
indicates engine overheating.  
śꢀ If you operate the air conditioner  
excessively, the difference between  
the temperature of the outside air and  
that of the windshield could cause  
the outer surface of the windshield to  
fog up, causing loss of visibility. In this  
case, set the mode selection button to  
the  
position and set the fan speed  
control knob to the lowest speed  
setting.  
5-112  
05  
Checking the amount of air  
conditioner refrigerant and  
compressor lubricant  
System maintenance  
Cabin air filter  
When the amount of refrigerant is low,  
the performance of the air conditioning  
is reduced. Overfilling also reduces the  
performance of the air conditioning system.  
Therefore, if abnormal operation is found,  
have the system be inspected by an  
authorized HYUNDAI dealer.  
NOTICE  
It is important that the correct type and  
amount of oil and refrigerant is used.  
Otherwise, damage to the compressor  
and abnormal system operation may  
occur. To prevent damage, the air  
conditioning system in your vehicle  
should only be serviced by trained and  
certified technicians.  
OIK047401L  
[A] : Outside air, [B] : Recirculated air  
[C] : Cabin air filter, [D] : Blower  
[E] : Evaporator core, [F] : Heater core  
The cabin air filter is installed behind  
the glove box. It filters the dust or other  
pollutants that enter the vehicle through  
the heating and air conditioning system.  
Have the cabin air filter be replaced  
by an authorized HYUNDAI dealer  
according to the maintenance schedule.  
If the vehicle is being driven in severe  
conditions such as dusty or rough roads,  
more frequent climate control filter  
inspections and changes are required.  
If the air flow rate suddenly decreases,  
have the system be checked at an  
authorized HYUNDAI dealer.  
5-113  
Convenience features  
NOTICE  
śꢀ The refrigerant system should only  
be serviced by trained and certified  
technicians to insure proper and safe  
operation.  
śꢀ The refrigerant system should be  
serviced in a well-ventilated place.  
śꢀ The air conditioning evaporator  
(cooling coil) shall never be repaired  
or replaced with one removed from  
a used or salvaged vehicle and new  
replacement MAC evaporators shall  
be certified (and labeled) as meeting  
SAE Standard J2842.  
OTM050040L  
Air Conditioning refrigerant label  
You can find out which air conditioning  
refrigerant is applied to your vehicle on  
the label located inside of the hood.  
WARNING  
Vehicles equipped with R-1234yf  
„Example  
Since the refrigerant is  
mildly flammable and  
operated at high pressure,  
the air conditioning system  
should only be serviced  
by trained and certified  
technicians. It is important  
that the correct type and  
amount of oil and refrigerant  
are used.  
OHYK059001  
All refrigerants should be reclaimed  
with proper equipment.  
Venting refrigerants directly to the  
atmosphere is harmful to individuals  
and environment. Failure to heed these  
warnings can lead to serious injuries.  
Each symbols and specification on  
the air conditioning refrigerant label is  
represented as below:  
1. Classification of refrigerant  
2. Amount of refrigerant  
3. Classification of compressor lubricant  
4. Caution  
5. Flammable refrigerant  
6. To require registered technician to  
service air conditioning system  
5-114  
05  
WINDSHIELD DEFROSTING AND DEFOGGING  
Manual climate control system  
To defog inside windshield  
WARNING  
Windshield heating  
Do not use the  
position during  
cooling operation in extremely humid  
weather. The difference between the  
temperature of the outside air and that  
of the windshield could cause the outer  
surface of the windshield to fog up,  
causing loss of visibility could cause  
an accident resulting in serious injury  
or death. In this case, set the mode  
selection button to the  
position  
and fan speed control knob to a lower  
speed.  
OTM050115  
1. Select any fan speed except “0”  
position.  
2. Select the desired temperature.  
3. Press the defroster button ( ).  
śꢀ For maximum defrost performance,  
set the temperature control to the  
highest temperature setting and  
the fan speed control to the highest  
setting.  
śꢀ If warm air to the floor is desired while  
defrosting or defogging, set the mode  
to the floor-defrost position.  
śꢀ Before driving, clear all snow and ice  
from the windshield, rear window,  
side view mirrors, and all side  
windows.  
śꢀ Clear all snow and ice from the  
hood and air inlet in the cowl grill  
to improve heater and defroster  
efficiency and to reduce the  
probability of fogging up the inside of  
the windshield.  
4. The outside (fresh) air will be selected  
automatically. Additionally, the  
air conditioning (if equipped) will  
automatically operate if the mode is  
selected to the  
position.  
If the air conditioning and outside  
(fresh) air position are not selected  
automatically, press the corresponding  
button manually.  
NOTICE  
If the engine temperature is still cold  
after starting, then a brief engine warm  
up period may be required for the  
vented air flow to become warm or hot.  
5-115  
Convenience features  
To defrost outside windshield  
Automatic climate control  
system  
To defog inside windshield  
OTM050126  
1. Set the fan speed to the highest  
(extreme right) position.  
OTM050116  
2. Set the temperature to the extreme  
hot position.  
3. Press the defroster button ( ).  
4. The outside (fresh) air and air  
conditioning (if equipped) will be  
selected automatically.  
1. Select the desired fan speed.  
2. Select the desired temperature.  
3. Press the defroster button ( ).  
4. The air-conditioning will turn on  
according to the detected ambient  
temperature, outside (fresh) air  
position and higher fan speed will be  
selected automatically.  
If the air-conditioning, outside (fresh)  
air position and higher fan speed are  
not selected automatically, adjust the  
corresponding button or knob manually.  
If the  
position is selected, lower fan  
speed is controlled to higher fan speed.  
5-116  
05  
To defrost outside windshield  
Auto defogging system (only  
for automatic climate control  
system, if equipped)  
Auto defogging help reduce the  
possibility of fogging up the inside of the  
windshield by automatically sensing the  
moisture on inside the windshield.  
The auto defogging system operates  
when the heater or air conditioning is on.  
Information  
The auto defogging system may not  
operate normally, when the outside  
temperature is below 14°F(-10°C).  
OTM050117  
1. Set fan speed to the highest position.  
2. Set temperature to the extreme hot  
(HI) position.  
To cancel or set the Auto Defogging  
System, keep the front defroster button  
pressed for 3 seconds. The “ADS OFF”  
symbol will be shown in the climate  
display to inform you that the system  
is deactivated. To re-activate the auto  
defogging system, follow the procedure  
mentioned above and the “ADS OFF”  
symbol will disappear.  
3. Press the defroster button ( ).  
4. The air-conditioning will turn  
on according to the detected  
ambient temperature and outside  
(fresh) air position will be selected  
automatically.  
If the  
position is selected, lower fan  
speed is controlled to higher fan speed.  
If the battery has been disconnected  
or discharged, it resets to the auto  
defogging status.  
Information  
For efficiency, do not select recirculated  
air position while the Auto defogging  
system is operating.  
NOTICE  
Do not remove the sensor cover located  
on the top of the windshield glass.  
Damage to system parts could occur  
and may not be covered by your vehicle  
warranty.  
5-117  
Convenience features  
Rear window defroster  
Information  
śꢀ If there is heavy accumulation of snow  
on the rear window, brush it off before  
operating the rear defroster.  
śꢀ The rear window defroster  
automatically turns off after  
approximately 20 minutes or when the  
Engine Start/Stop button is in the OFF  
position.  
NOTICE  
To prevent damage to the rear window  
defroster conducting elements bonded  
to the inside surface of the rear window,  
never use sharp instruments or window  
cleaners containing abrasives to clean  
the window.  
The defroster heats the  
window to remove frost, fog  
and thin ice from the interior  
and exterior of the rear  
window, while the engine is  
running.  
Side view mirror defroster (if  
equipped)  
If your vehicle is equipped with the Side  
view mirror defrosters, they will operate  
at the same time you turn on the rear  
window defroster.  
śꢀ To activate the rear window defroster,  
press the rear window defroster  
button located in the center control  
panel. The indicator on the rear  
window defroster button illuminates  
when the defroster is ON.  
śꢀ To turn off the defroster, press the rear  
window defroster button again.  
5-118  
05  
&/,0$7(ꢀ&21752/ꢀ$'',7,21$/ꢀ)($785(6  
When the Auto Defogging  
Auto defogging system  
System operates, the indicator  
will illuminate.  
If a high amount of humidity is detected  
in the vehicle, the Auto Defogging  
System will be enabled. The following  
steps will be performed automatically:  
Step 1) Air conditioning will turn ON.  
Step 2) Air intake control will change to  
Fresh mode.  
Step 3) Mode will change to defrost to  
direct airflow to the windshield.  
Step 4) Fan speed will be set to MAX.  
OTM050039  
Auto defogging helps reduce the  
If the air conditioning is off or  
possibility of fogging up the inside of the  
windshield by automatically sensing the  
moisture on inside the windshield.  
recirculation mode is manually selected  
while Auto Defogging System is ON, the  
Auto Defogging System indicator will  
blink 3 times to signal that the manual  
operation has been canceled.  
The auto defogging system operates  
when the heater or air conditioning is on.  
Information  
The auto defogging system may not  
operate normally, when the outside  
temperature is below 14°F (10°C).  
5-119  
Convenience features  
NOTICE  
Turning the Auto Defogging System  
ON or OFF  
Climate control system  
Do not remove the sensor cover located  
on the upper end of the windshield  
glass.  
Damage to system parts could occur  
and may not be covered by your vehicle  
warranty.  
Press the front windshield defroster  
button for 3 seconds when the Engine  
Start/Stop button is in the ON position.  
When the Auto Defogging System is  
turned off, the ADS OFF symbol will blink  
3 times and ADS OFF will be displayed on  
the climate control information screen.  
When the Auto Defogging System is  
turned on, the ADS OFF symbol will blink  
6 times without a signal.  
Auto dehumidify (if equipped)  
To increase cabin air quality and reduce  
windshield misting, recirculation mode  
switches off automatically after about 5  
to 30 minutes, depending on the outside  
temperature, and the air intake will  
change to fresh mode.  
Infotainment system  
Auto Defogging System can be turned  
RQꢀDQGꢀRIIꢀE\ꢀVHOHFWLQJꢀœ6HWXSꢀƟꢀ  
9HKLFOHꢀ6HWWLQJVꢀƟꢀ&OLPDWHꢀƟꢀ'HIRJꢁ  
'HIURVWꢀ2SWLRQVꢀƟꢀ$XWRꢀ'HIRJŔꢀIURPꢀWKHꢀ  
infotainment system screen.  
For detailed information, refer to the  
separately supplied infotainment  
system manual.  
Turning Auto Dehumidify ON or OFF  
Climate control system  
To turn the Auto Dehumidify feature  
on or off, select Face level ( ) mode  
and press the air intake control (  
button at least five times within three  
seconds. When Auto Dehumidify is  
)
turned on, the air intake control button  
indicator will blink 6 times. When turned  
off, the indicator will blink 3 times.  
Information  
śꢀ When the air conditioning is turned  
on by Auto Defogging System, if you  
try to turn off the air conditioning, the  
indicator will blink 3 times and the air  
conditioning will not be turned off.  
śꢀ To maintain the effectiveness and  
efficiency of the Auto Defogging  
System, do not select Recirculation  
mode while the system is operating.  
śꢀ When Auto Defogging System is  
operating, fan speed adjustment,  
temperature adjustment, and air intake  
control selection are all disabled.  
Infotainment system  
Auto Dehumidify can be turned on and  
RIIꢀE\ꢀVHOHFWLQJꢀœ6HWXSꢀƟꢀ9HKLFOHꢀ6HWWLQJVꢀ  
Ɵꢀ&OLPDWHꢀƟꢀ$XWRPDWLFꢀ9HQWLODWLRQꢀƟꢀ  
Auto Dehumidify’ from the infotainment  
system screen.  
For detailed information, refer to the  
separately supplied infotainment  
system manual.  
5-120  
05  
Recirculating air when washer  
fluid is used  
Recirculation mode automatically  
activates to reduce any objectionable  
scent of the washer fluid from entering  
the cabin when the windshield washer is  
used.  
Sunroof inside air recirculation  
(if equipped)  
When the is sunroof opened, fresh  
mode will be automatically selected.  
At this time, if you press the air intake  
control button, recirculation mode will  
be selected but will change back to fresh  
mode after 3 minutes. When the sunroof  
is closed, the air intake position will  
return to the original position that was  
selected.  
Turning Activate upon Washer Fluid  
Use ON or OFF  
Climate control system  
To turn the Activate upon Washer Fluid  
Auto. Controls That Use Climate  
Control Settings (for driver’s  
seat)  
The temperature of the driver’s seat  
warmer, air ventilated seat and heated  
steering wheel is automatically  
controlled depending on the inside and  
outside temperature of the vehicle when  
the engine is running.  
To use these features, it must be  
enabled from the Settings menu in the  
infotainment system screen. Select:  
Use feature on or off, select Floor level  
(
) mode, and then press the air  
intake control (  
) button four times  
within two seconds while pressing the  
A/C icon.  
When Activate upon Washer Fluid Use  
ON is turned on, the air intake control  
button indicator will blink 6 times. When  
turned off, the indicator will blink 3  
times.  
Infotainment system  
-
6HWXSꢀƟꢀ9HKLFOHꢀ6HWWLQJVꢀƟꢀ6HDWꢀƟꢀ  
+HDWHGꢁ9HQWLODWHGꢀ)HDWXUHVꢀƟꢀ+HDWHGꢁ  
9HQWLODWHGꢀ)HDWXUHVꢀƟꢀ$XWRꢃꢀ&RQWUROVꢀ  
That Use Climate Control Settings  
Activate upon Washer Fluid Use can be  
WXUQHGꢀRQꢀDQGꢀRIIꢀE\ꢀVHOHFWLQJꢀœ6HWXSꢀƟꢀ  
9HKLFOHꢀ6HWWLQJVꢀƟꢀ&OLPDWHꢀƟꢀ5HFLUFXODWHꢀ  
$LUꢀƟꢀ$FWLYDWHꢀXSRQꢀ:DVKHUꢀ)OXLGꢀ8VHꢀ  
(or Interlocking washer fluid)’ from the  
infotainment system screen.  
For detailed information, refer to the  
separately supplied infotainment  
system manual.  
For more details on Auto Comfort  
Control, refer to “Seat Warmers” and  
“Air ventilation seats” section in chapter  
3 and “Heated Steering Wheel” section  
in chapter 5.  
However, in cold weather to prevent  
the windshield from fogging up, the  
recirculation mode may not be selected.  
5-121  
Convenience features  
6725$*(ꢀ&203$570(17  
Center console storage  
WARNING  
Never store cigarette lighters, propane  
cylinders, or other flammable/explosive  
materials in the vehicle. These items  
may catch fire and/or explode if the  
vehicle is exposed to hot temperatures  
for extended periods.  
WARNING  
ALWAYS keep the storage compartment  
covers closed securely while driving.  
Items inside your vehicle are moving as  
fast as the vehicle. If you have to stop  
or turn quickly, or if there is a crash, the  
items may fly out of the compartment  
and may cause an injury if they strike  
the driver or a passenger.  
OTM050037  
To open:  
Press the button.  
Glove box  
NOTICE  
To avoid possible theft, do not leave  
valuables in the storage compartments.  
OTM050223L  
To open:  
Pull the lever (1).  
WARNING  
ALWAYS close the glove box door after  
use.  
An open glove box door can cause  
serious injury to the passenger in an  
accident, even if the passenger is  
wearing a seat belt.  
5-122  
05  
Tray  
Luggage tray (if equipped)  
„Type A  
OTM050034  
OTM050202  
„Type B  
WARNING  
Do not place the heavy, sharp or  
breakable objects in the tray. Such  
objects can be thrown from the  
tray in the event of a sudden stop  
or an accident, possibly injuring the  
passengers in the vehicle.  
OTM050203  
You can place a first aid kit, a reflector  
triangle (front tray), tools, etc., in the box  
for easy access.  
śꢀ Grasp the handle on the top of the  
cover and lift it.  
5-123  
Convenience features  
INTERIOR FEATURES  
Cup holder  
„Front  
WARNING  
śꢀ Avoid abrupt starting and braking  
when the cup holder is in use to  
prevent spilling your drink. If hot  
liquid spills, you could be burned.  
Such a burn to the driver could cause  
loss of vehicle control resulting in an  
accident.  
śꢀ Do not place uncovered or unsecured  
cups, bottles, cans, etc., in the cup  
holder containing hot liquid while  
the vehicle is in motion. Injuries may  
result in the event of a sudden stop  
or collision.  
OTM050030L  
„Rear  
śꢀ Only use soft cups in the cup holders.  
Hard objects can injure you in an  
accident.  
śꢀ Do not forcefully open the cover. It  
may damage if you forcefully open  
the cover with your fingers, etc..  
WARNING  
Keep cans or bottles out of direct sun  
light and do not put them in a hot  
vehicle. It may explode.  
OTMPH051013N  
Cups or small beverages cups may be  
placed in the cup holders.  
NOTICE  
śꢀ Keep your drinks sealed while  
driving to prevent spilling your drink.  
If liquid spills, it may get into the  
vehicle’s electrical/electronic system  
and damage electrical/electronic  
parts.  
śꢀ When cleaning spilled liquids do not  
use hot air to blow out or dry the cup  
holder. This may damage the interior.  
5-124  
05  
Ashtray (if equipped)  
Sunvisor  
OPDE046419  
OTM048089  
To use the ashtray, open the cover.  
To use the sunvisor, pull it downward.  
To use the sunvisor to block the sun  
from the side window, pull it downward,  
release it from the bracket (1) and swing  
it to the side (2) towards the window.  
To use the vanity mirror, pull down the  
sunvisor and slide the mirror cover (3).  
Adjust the sunvisor forward or backward  
(4) as needed (if equipped). Use the  
ticket holder (5) to hold tickets.  
Close the vanity mirror cover securely  
and return the sunvisor to its original  
position after use.  
To clean the ashtray:  
The plastic receptacle should be  
removed by lifting the plastic ashtray  
receptacle upward after turning the  
cover counterclockwise and pulling it  
out.  
WARNING  
Putting lit cigarettes or matches in  
an ashtray with other combustible  
materials may cause a fire.  
WARNING  
For your safety, do not block your view  
when using the sunvisor.  
NOTICE  
The tab (5) adjacent to the vanity mirror  
on the sunvisor can be used for toll  
road tickets or self parking tickets. Use  
caution when inserting tickets into the  
ticket holder to avoid damage. Refrain  
from putting several tickets in the ticket  
holder as this could also damage the  
retaining tab.  
5-125  
Convenience features  
Power outlet  
„Front  
CAUTION  
To prevent damage to the power  
outlets:  
śꢀ Use the power outlet only when the  
engine is running and remove the  
accessory plug after use. Using the  
accessory plug for prolonged periods  
of time with the engine off could  
cause the battery to discharge.  
śꢀ Only use 12 volts electric accessories  
which are less than 180 watts in  
electric capacity.  
OTM050026  
śꢀ Adjust the air-conditioner or heater  
to the lowest operating level when  
using the power outlet.  
„Rear  
śꢀ Close the cover when not in use.  
śꢀ Some electronic devices can  
cause electronic interference  
when plugged into a vehicle’s  
power outlet. These devices may  
cause excessive audio static and  
malfunctions in other electronic  
systems or devices used in your  
vehicle.  
śꢀ Push the plug in as far as it will go. If  
good contact is not made, the plug  
may overheat and the fuse may open.  
śꢀ Plug in battery equipped electrical/  
electronic devices with reverse  
current protection. The current  
from the battery may flow into the  
vehicle’s electrical/electronic system  
and cause system malfunction.  
OTM050031  
The power outlet is designed to provide  
power for mobile telephones or other  
devices designed to operate with vehicle  
electrical systems. The devices should  
draw less than 180 watts with the engine  
running.  
WARNING  
Avoid electrical shocks. Do not place  
your fingers or foreign objects (pin, etc.)  
into a power outlet or touch the power  
outlet with a wet hand.  
5-126  
05  
USB charger  
AC Inverter (if equipped)  
„Front  
OTM050028  
OTMA050011  
„Rear  
The AC inverter supplies 115V/150W  
electric power to operate electric  
accessories or equipments.  
Information  
OTM050058  
The USB charger is designed to recharge  
batteries of small size electrical devices  
using a USB cable.  
The electrical devices can be recharged  
when the Engine Start/Stop button is in  
the ACC or ON (or START) position.  
The battery charging state may be  
monitored on the electrical device.  
Disconnect the USB cable from the USB  
port after use.  
śꢀ A smart phone or a tablet PC may  
get warmer during the re-charging  
process. It does not indicate any  
malfunction with the charging system.  
OJX1070288L  
śꢀ Rated voltage : AC 115 volts  
śꢀ Maximum electric power : 150 watts  
śꢀ In order to avoid an electrical system  
failure, electric shock, etc., be sure to  
read owner’s manual before use.  
śꢀ Be sure to close the cover except the  
time of use.  
śꢀ A smart phone or a tablet PC, which  
adopts a different re-charging  
method, may not be properly re-  
charged. In this case, use an exclusive  
charger of your device.  
śꢀ The charging terminal is only to  
recharge a device. Do not use the  
charging terminal either to turn ON  
an audio or to play media In the  
infotainment system.  
5-127  
Convenience features  
NOTICE  
WARNING  
śꢀ To help prevent the battery from  
being discharged, do not use the  
AC inverter while the engine is not  
running.  
śꢀ When not using the AC inverter,  
make sure to close the AC inverter  
cover.  
śꢀ After using an electric accessory  
or equipment, pull the plug out.  
Leaving the accessory or equipment  
plugged in for a long time may cause  
battery discharge.  
To reduce a risk of serious or fatal  
injuries:  
śꢀ Do not use a heated electric device  
such as a coffeepot, toaster, heater,  
iron, etc.  
śꢀ Do not insert foreign objects into the  
outlet and do not touch the outlet as  
you may get shocked.  
śꢀ Do not let children touch the AC  
inverter.  
śꢀ Do not use an electric accessory or  
equipment the power consumption  
of which is greater than 220  
volts/200 watts.  
śꢀ Some electric accessories or  
equipment can cause electronic  
interference. It may cause excessive  
audio noise and malfunctions in  
other electric systems or devices in  
the vehicle.  
śꢀ Do not use broken electric  
accessories or equipment, which  
may damage the AC inverter and  
electrical systems of the vehicle.  
śꢀ Do not use two or more electric  
accessories or equipment at the  
same time. It may cause damage to  
the electrical systems of the vehicle.  
śꢀ When the input voltage is lower,  
outlet LED will blink and the AC  
inverter will turn off automatically. If  
the input voltage goes up to normal,  
the AC inverter will turn on again.  
5-128  
05  
To charge a cellular phone  
Wireless smart phone charging  
system (if equipped)  
The wireless smart phone charging  
system charges only the Qi-enabled  
smart phones ( ). Read the label on  
the smart phone accessory cover or  
visit your smart phone manufacturer’s  
website to check whether your smart  
phone supports the Qi technology.  
The wireless charging process starts  
when you put a Qi-enabled smart phone  
on the wireless charging unit.  
1. Remove other items, including the  
smart key, from the wireless charging  
unit. If not, the wireless charging  
process may be interrupted. Place  
the smart phone on the center of the  
charging pad.  
2. The indicator light is orange when the  
smart phone is charging. The indicator  
light will turn blue when phone  
charging is complete.  
OTM050022  
[A] : Indicator light, [B] : Charging pad  
On certain models, the vehicle comes  
equipped with a wireless smart phone  
charger.  
The system is available when all doors  
are closed, and when the Engine Start/  
Stop button is in the ACC or ON (or  
START) position.  
3. You can turn ON or OFF the wireless  
charging function from the Settings  
menu on the instrument cluster.  
Select:  
- 6HWXSꢀƟꢀ8VHUꢀVHWWLQJVꢀƟꢀ  
&RQYHQLHQFHꢀƟꢀ:LUHOHVVꢀ&KDUJLQJꢀ  
If your smart phone is not charging:  
-
Slightly change the position of the  
smart phone on the charging pad.  
-
Make sure the indicator light is  
orange.  
5-129  
Convenience features  
The indicator light will blink orange for 10  
seconds if there is a malfunction in the  
wireless charging system.  
In this case, temporarily stop the  
charging process, and re-attempt to  
charge your smart phone again.  
The system warns you with a message on  
the LCD display if the smart phone is still  
on the wireless charging unit after the  
vehicle is turned OFF and the front door  
is opened.  
NOTICE  
śꢀ The wireless smart phone charging  
system may not support certain  
smart phones, which are not verified  
for the Qi specification ( ).  
śꢀ When placing your smart phone on  
the charging pad, position the phone  
in the middle of the mat for optimal  
charging performance. If your smart  
phone is off to the side, the charging  
rate may be less and in some cases  
the smart phone may experience  
higher heat conduction.  
śꢀ In some cases, the wireless charging  
may stop temporarily when the  
smart key is used, either when  
starting the vehicle or locking/  
unlocking the doors, etc.  
śꢀ When charging certain smart  
phones, the charging indicator may  
not change to blue when the smart  
phone is fully charged.  
For some manufacturer’s smart phones,  
the system may not warn you even  
though the smart phone is left on the  
wireless charging unit. This is due to the  
particular characteristic of the smart  
phone and not a malfunction of the  
wireless charging.  
Information  
For some manufacturers’ cellular phones,  
the system may not warn you even though  
the cellular phone is left on the wireless  
charging unit. This is due to the particular  
characteristic of the cellular phone and  
not a malfunction of the wireless charging.  
śꢀ The wireless charging process may  
temporarily stop, when temperature  
abnormally increases inside the  
wireless smart phone charging  
system. The wireless charging  
process restarts, when temperature  
falls to a certain level.  
śꢀ The wireless charging process may  
temporarily stop when there is  
any metallic item, such as a coin,  
between the wireless smart phone  
charging system and smart phone.  
5-130  
05  
śꢀ When charging some smart phones  
with a self-protection feature,  
the wireless charging speed may  
decrease and the wireless charging  
may stop.  
śꢀ If the smart phone has a thick cover,  
the wireless charging may not be  
possible.  
Clock  
The clock can be set from the  
infotainment system.  
For detailed information, refer to the  
separately supplied infotainment  
system manual.  
WARNING  
śꢀ If the smart phone is not completely  
contacting the charging pad,  
wireless charging may not operate  
properly.  
śꢀ Some magnetic items like credit  
cards, phone cards or rail tickets may  
be damaged if left with the smart  
phone during the charging process.  
Do not attempt to adjust the clock  
while driving. Doing so may result in  
distracted driving which may lead to  
an accident involving personal injury or  
death.  
Coat hook  
śꢀ When any smart phone without  
a wireless charging function or a  
metallic object is placed on the  
charging pad, a small noise may  
sound. This small sound is due to the  
vehicle discerning compatibility of  
the object placed on the charging  
pad. It does not affect your vehicle or  
the smart phone in any way.  
Information  
OTM048095  
If the Ignition switch is in the OFF  
These hooks are not designed to hold  
large or heavy items.  
position, the charging also stops.  
Information  
This device complies with part 15 of the  
FCC Rules.  
Operation is subject to the following two  
conditions:  
1. This device may not cause harmful  
interference, and  
2. This device must accept any  
interference received, including  
interference that may cause undesired  
operation.  
5-131  
Convenience features  
WARNING  
WARNING  
The following must be observed when  
installing ANY floor mat to the vehicle.  
śꢀ Ensure to remove a protective  
film attached on the carpet  
before attaching a floor mat on  
the front floor carpet. Otherwise,  
the floor mat may move freely on  
the protective film and it could  
result in unintentional braking or  
accelerating.  
śꢀ Ensure that the floor mats are  
securely attached to the vehicle’s  
floor mat anchor(s) before driving  
the vehicle.  
śꢀ Do not use ANY floor mat that cannot  
be firmly attached to the vehicle’s  
floor mat anchors.  
śꢀ Do not stack floor mats on top of one  
another (for example, all-weather  
rubber mat on top of a carpeted floor  
mat). Only a single floor mat should  
be installed in each position.  
OTM048096  
Do not hang other objects such  
as hangers or hard objects except  
clothes. Also, do not put heavy, sharp  
or breakable objects in the clothes  
pockets. In an accident or when the  
curtain air bag is inflated, it may cause  
vehicle damage or personal injury.  
Floor mat anchor(s)  
IMPORTANT - Your vehicle was  
ALWAYS use the Floor Mat Anchors to  
attach the front floor mats to the vehicle.  
The anchors on the front floor carpet  
keep the floor mats from sliding forward.  
manufactured with driver’s side floor  
mat anchors that are designed to  
securely hold the floor mat in place.  
To avoid any interference with pedal  
operation, HYUNDAI recommends that  
the HYUNDAI floor mat designed for use  
in your vehicle be installed.  
WARNING  
Do not overlay additional mats or liners  
over the floor mats. If using All Weather  
mats, remove the carpeted floor mats  
before installing them. Only use floor  
mats designed to connect to the  
anchors.  
5-132  
05  
Side curtain (if equipped)  
Luggage net holder (if equipped)  
„Type A  
OTM050206  
OTMPH051014N  
„Type B  
To use the side curtain:  
1. Lift the curtain by the hook (1).  
2. Hang the curtain on both sides of the  
hook.  
CAUTION  
śꢀ Always hang both sides of the  
curtain on the hook. This could cause  
damage to the side curtain if only  
one side of the curtain is hooked.  
OTMPH051015N  
śꢀ Do not let any foreign material get  
in between the vehicle and side  
curtain. The side curtain may not be  
lifted up.  
To keep items from shifting in the  
luggage compartment, you can use the 4  
holders located in the luggage side trim  
to attach the luggage net.  
Make sure the luggage net is securely  
attached to the holders in the luggage  
board.  
If necessary, contact your authorized  
HYUNDAI dealer to obtain a luggage net.  
5-133  
Convenience features  
Using the cargo security screen  
WARNING  
Avoid eye injury. DO NOT overstretch  
the luggage net. ALWAYS keep your  
face and body out of the luggage net’s  
recoil path. DO NOT use the luggage net  
when the strap has visible signs of wear  
or damage.  
Use the luggage net to keep only light  
items from shifting in the luggage  
compartment.  
Cargo security screen (if  
equipped)  
OTMPH051017N  
1. Pull the cargo security screen towards  
the rear of the vehicle by the handle  
(1).  
2. Insert the guide pin (2) into the guide  
(3).  
Information  
Pull out the cargo security screen with the  
handle in the center to prevent the guide  
pin from falling out of the guide.  
OTMPH051016N  
When the cargo security screen is not in  
use:  
1. Pull the cargo security screen  
backward and up to release it from  
the guides.  
Use the cargo security screen to cover  
items stored in the cargo area.  
2. The cargo security screen will  
automatically slide back in.  
Information  
The cargo security screen may not  
automatically slide back in if the cargo  
security screen is not fully pulled out. Pull  
the cargo screen out all the way and then  
slowly allow the screen to retract back in.  
5-134  
05  
NOTICE  
Since the cargo security screen may  
be damaged or malformed, do not put  
luggage on it when it is used.  
WARNING  
śꢀ Do not place objects on the cargo  
security screen. Such objects may be  
thrown about inside the vehicle and  
possibly injure vehicle occupants  
during an accident or when braking.  
śꢀ Never allow anyone to ride in the  
luggage compartment. It is designed  
for luggage only.  
śꢀ Maintain the balance of the vehicle  
and locate the weight as forward as  
possible.  
5-135  
Convenience features  
EXTERIOR FEATURES  
Roof side rails  
WARNING  
śꢀ The following specification is the  
maximum weight that can be loaded  
onto the roof side rails. Distribute the  
load as evenly as possible onto the  
roof side rails and secure the load  
firmly.  
Loading cargo or luggage in excess  
of the specified weight limit on the  
roof side rails may damage your  
vehicle.  
OTM050017  
ROOF SIDE  
RAILS  
220 lbs. (100 kg)  
EVENLY DISTRIBUTED  
If your vehicle comes with roof side rails,  
then roof side rails crossbars can be  
installed on top of your vehicle.  
The roof side rails crossbars are an  
accessory and are available at your  
HYUNDAI dealer.  
śꢀ The vehicle center of gravity will be  
higher when items are loaded onto  
the roof side rails. Avoid sudden  
starts, braking, sharp turns, abrupt  
maneuvers or high speeds that may  
result in loss of vehicle control or  
rollover resulting in an accident.  
śꢀ Always drive slowly and turn corners  
carefully when carrying items on the  
roof side rails. Severe wind updrafts,  
caused by passing vehicles or natural  
causes, can cause sudden upward  
pressure on items loaded on the  
NOTICE  
If the vehicle is equipped with a  
sunroof, be sure not to position cargo  
onto the roof side rails in such a way  
that it could interfere with sunroof  
operation.  
roof side rails. This is especially true  
when carrying large, flat items such  
as wood panels or mattresses. This  
could cause the items to fall off the  
roof side rails and cause damage to  
your vehicle or others around you.  
NOTICE  
śꢀ When carrying cargo on the roof side  
rails, take the necessary precautions  
to make sure the cargo does not  
damage the roof of the vehicle.  
śꢀ To prevent damage or loss of cargo  
while driving, check frequently  
before or while driving to make sure  
the items on the roof side rails are  
securely fastened.  
śꢀ When carrying large objects on the  
roof side rails, make sure they do  
not exceed the overall roof length or  
width.  
5-136  
05  
,1)27$,10(17ꢀ6<67(0  
NOTICE  
Antenna  
Shark fin antenna  
śꢀ If you install an aftermarket HID  
head lamp, your vehicle’s audio and  
electronic devices may not function  
properly.  
śꢀ Prevent chemicals such as perfume,  
cosmetic oil, sun cream, hand  
cleaner, and air freshener from  
contacting the interior parts  
because they may cause damage or  
discoloration.  
USB Port  
OTM049420  
The shark fin antenna receives  
transmitted data. (for example: AM/FM,  
DAB, GPS)  
Steering wheel remote controls  
OTM050016  
You can use an USB cable to connect  
audio devices to the vehicle USB port.  
Information  
When using a portable audio device  
connected to the power outlet, noise may  
occur during playback. If this happens,  
use the portable audio device’s power  
source.  
OTM050207  
NOTICE  
Do not operate multiple audio remote  
control buttons simultaneously.  
5-137  
Convenience features  
VOLUME (VOL + / VOL -) (1)  
Infotainment system  
For detailed information, refer to the  
separately supplied infotainment system  
manual.  
śꢀ Rotate the VOLUME scroll up to  
increase volume.  
śꢀ Rotate the VOLUME scroll down to  
decrease volume.  
Voice recognition  
SEEK/PRESET (  
/
) (2)  
If the SEEK/PRESET switch is pressed up  
or down and held for 0.8 second or more,  
it will function in the following modes:  
śꢀ RADIO mode  
It will function as the AUTO SEEK  
select button. It will SEEK until you  
release the button.  
śꢀ MEDIA mode  
It will function as the FF/RW button.  
OTM050209  
If the SEEK/PRESET switch is pressed up  
or down, it will function in the following  
modes:  
For detailed information, refer to the  
separately supplied infotainment  
system manual.  
śꢀ RADIO mode  
It will function as the PRESET STATION  
UP/DOWN button.  
śꢀ MEDIA mode  
It will function as the TRACK UP/  
DOWN button.  
MODE (3)  
Press the MODE button to toggle  
through Radio or Media modes.  
MUTE ( ) (4)  
śꢀ Press the MUTE button to mute the  
sound.  
śꢀ Press the MUTE button again to  
activate the sound.  
Information  
See additional information in supplied  
Infotainment Manual.  
5-138  
05  
Bluetooth® Wireless Technology  
How vehicle radio works  
FM reception  
OTM050208  
OJF045308L  
AM and FM radio signals are broadcast  
from transmitter towers located around  
your city. They are intercepted by the  
radio antenna on your vehicle. This signal  
is then received by the radio and sent to  
your vehicle speakers.  
When a strong radio signal has reached  
your vehicle, the precise engineering  
of your audio system ensures the best  
possible quality reproduction. However,  
in some cases the signal coming to your  
vehicle may not be strong and clear.  
This can be due to factors, such as  
the distance from the radio station,  
closeness of other strong radio stations  
or the presence of buildings, bridges or  
other large obstructions in the area.  
OTM050224L  
(1) Call / Answer button  
(2) Call end button  
(3) Microphone  
For detailed information, refer to the  
separately supplied infotainment  
system manual.  
CAUTION  
To avoid driver distractions, do not  
excessively operate the device while  
driving the vehicle which may lead to  
an accident.  
5-139  
Convenience features  
AM (MW, LW) reception  
FM radio station  
OJF045309L  
OJF045310L  
AM broadcasts can be received at  
greater distances than FM broadcasts.  
This is because AM radio waves are  
transmitted at low frequencies. These  
long, low frequency radio waves can  
follow the curvature of the earth rather  
than travelling straight out into the  
atmosphere.  
FM broadcasts are transmitted at high  
frequencies and do not bend to follow  
the earth’s surface. Because of this, FM  
broadcasts generally begin to fade at  
short distances from the station. Also, FM  
signals are easily affected by buildings,  
mountains, or other obstructions. These  
can result in certain listening conditions  
which might lead you to believe a  
In addition, they curve around  
obstructions so that they can provide  
better signal coverage.  
problem exists with your radio.  
The following conditions are normal and  
do not indicate radio trouble :  
JBM004  
śꢀ Fading - As your vehicle moves away  
from the radio station, the signal will  
weaken and sound will begin to fade.  
When this occurs, we suggest that you  
select another stronger station.  
5-140  
05  
śꢀ Flutter/Static - Weak FM signals  
or large obstructions between the  
transmitter and your radio can disturb  
the signal causing static or fluttering  
noises to occur. Reducing the treble  
level may lessen this effect until the  
disturbance clears.  
Using a cellular phone or a twoway  
radio  
When a cellular phone is used inside  
the vehicle, noise may be produced  
from the audio system. This does not  
mean that something is wrong with the  
audio equipment. In such a case, use  
the cellular phone at a place as far as  
possible from the audio equipment.  
NOTICE  
When using a communication system  
such as a cellular phone or a radio set  
inside the vehicle, a separate external  
antenna must be fitted. When a cellular  
phone or a radio set is used with an  
internal antenna alone, it may interfere  
with the vehicle’s electrical system and  
adversely affect safe operation of the  
vehicle.  
OJF045311L  
śꢀ Station Swapping - As a FM signal  
weakens, another more powerful  
signal near the same frequency may  
begin to play. This is because your  
radio is designed to lock onto the  
clearest signal. If this occurs, select  
another station with a stronger signal.  
WARNING  
Do not use a cellular phone while  
driving. Stop at a safe location to use a  
cellular phone.  
śꢀ Multi-Path Cancellation - Radio  
signals being received from several  
directions can cause distortion or  
fluttering. This can be caused by a  
direct and reflected signal from the  
same station, or by signals from two  
stations with close frequencies. If this  
occurs, select another station until the  
condition has passed.  
5-141  
Convenience features  
iPod®  
iPod® is a registered trademark of Apple  
Inc.  
Bluetooth® Wireless Technology  
The Bluetooth® word mark and logos  
are registered trademarks owned by  
Bluetooth SIG, Inc. and any use of such  
marks by HYUNDAI is under license.  
Other trademarks and trade names are  
those of their respective owners.  
A Bluetooth® Wireless Technology  
enabled cell phone is required to use  
Bluetooth® Wireless Technology.  
5-142  
05  
,1)27$,10(17ꢀ6<67(0ꢀ63(&,),&$7,216ꢀ  
śꢀ Maximum length of folder/file names  
USB  
(Based on Unicode): 40 English or  
Korean characters  
Supported audio formats  
śꢀ Audio file specification  
- WAVeform audio format  
- MPEG1/2/2.5 Audio Layer3  
- Windows Media Audio Ver 7.X/8.X  
śꢀ Bit rates  
śꢀ Supported characters for folder/  
file names (Unicode support): 2,604  
Korean characters, 94 alphanumeric  
characters, 4,888 Chinese characters  
in common use, 986 special  
characters  
- MPEG1 (Layer3):  
32/40/48/56/64/80/96/112/128/160  
/192/224/256/320 kbps  
śꢀ Maximum number of folders: 1,000  
śꢀ Maximum number of files: 5,000  
- MPEG2 (Layer3):  
8/16/24/32/40/48/56/64/80/96/112  
/128/144/160 kbps  
NOTICE  
śꢀ Files that are not in a supported  
format may not be recognised or  
played, or information about them,  
such as the file name, may not be  
displayed properly.  
śꢀ Only files with .mp3/.wma/.wav  
extensions can be recognised by the  
system. If the file is not in supported  
format, change the file format by  
using the latest encoding software.  
śꢀ The device will not support files  
locked by DRM (Digital Rights  
Management).  
śꢀ For MP3/WMA compression files and  
WAV file, differences in sound quality  
will occur depending on the bitrate.  
(Music files with a higher bitrate  
have a better sound quality.)  
- MPEG2.5 (Layer3):  
8/16/24/32/40/48/56/64/80/96/112  
/128/144/160 kbps  
- WMA (High Range):  
48/64/80/96/128/160/192 kbps  
śꢀ Bits Per Sample  
- WAV (PCM(Stereo)): 24 bit  
- WAV (IMA ADPCM): 4 bit  
- WAV (MS ADPCM): 4 bit  
śꢀ Sampling frequency  
- MPEG1: 44100/48000/32000 Hz  
- MPEG2: 22050/24000/16000 Hz  
- MPEG2.5: 11025/12000/8000 Hz  
- WMA: 32000/44100/48000 Hz  
- WAV: 44100/48000 Hz  
śꢀ Japanese or Simplified Chinese  
characters in folder or file names  
may not be displayed properly.  
5-143  
Convenience features  
75$'(0$5.6  
Other trademarks and trade names are  
those of their respective owners.  
Supported USB storage devices  
śꢀ Byte/Sector: 64 kbyte or less  
śꢀ The Bluetooth®  
word mark and  
logos are registered  
trademarks owned  
by Bluetooth SIG,  
Inc. and any use  
of such marks by  
HYUNDAI is under  
licence.  
śꢀ Format system: FAT12/16/32  
(recommended), exFAT/NTFS  
NOTICE  
śꢀ Operation is guaranteed only for a  
metal cover type USB storage device  
with a plug type connector.  
- USB storage devices with a plastic  
plug may not be recognised.  
- USB storage devices in memory  
card types, such as CF card or SD  
cards, may not be recognised.  
śꢀ USB hard disk drives may not be  
recognised.  
śꢀ When you use a large capacity USB  
storage device with multiple logical  
drives, only files stored on the first  
drive will be recognised.  
śꢀ If an application program is loaded  
on a USB storage device, the  
corresponding media files may not  
play.  
śꢀ Use USB 2.0 devices for better  
compatibility.  
Bluetooth  
śꢀ Bluetooth Power Class 2: -6 to 4 dBm  
śꢀ Aerial power: Max 3 mW  
śꢀ Frequency range: 2400 to 2483.5 MHz  
śꢀ Bluetooth patch RAM software  
version: 1  
5-144  

Related Topics