Get Instrument cluster -> Warning and indicator lights Guide for Hyundai Santa Fe SUV 2023

04

Fuel economy (for 12.3-inch cluster)

Transmission shift indicator

Automatic transmission / Dual

clutch transmission shift indicator

ꢀ4.2-inch

ꢀ12.3-inch

OTMA040002

The average fuel economy (1) and instant

fuel economy (2) is displayed at the

bottom of the cluster.

OTM040016

OCN7040013N

This indicator informs the current gear

engaged.

Automatic reset

To automatically reset the average fuel

economy, select between "After Ignition"

or "After Refueling" from the Settings

menu in the infotainment system screen.

4-9

Instrument cluster

Parking brake & Brake fluid

warning light

Warning and indicator lights

Information

Make sure that all warning lights are OFF

after starting the engine. If any light is still

ON, this indicates a situation that needs

attention.

This warning light illuminates:

śꢀ When you set the ignition switch or

the Engine Start/Stop button to the

ON position.

- The parking brake & brake fluid

warning light illuminates for about 3

seconds and will then turn off once

the parking brake is released.

Seat belt warning light

śꢀ Whenever the parking brake is

applied.

This warning light informs the driver that

the seat belt is not fastened.

For more details, refer to “Seat Belts”

section in chapter 3.

śꢀ Whenever the brake fluid level in the

reservoir is low.

- If the warning light illuminates

with the parking brake released, it

indicates the brake fluid level in the

reservoir is low.

Air bag warning light

If the brake fluid level in the reservoir is

low:

This warning light illuminates:

śꢀ When you turn the ignition switch or

the Engine Start/Stop button to the

ON position.

1. Drive carefully to the nearest safe

location and stop your vehicle.

2. With the engine stopped, check the

brake fluid level immediately and add

fluid as required (For more details,

refer to “Brake Fluid” section in

chapter 9). After adding brake fluid,

check all brake components for fluid

leaks. If a brake fluid leak is found, or

if the warning light remains on, or if

the brakes do not operate properly, do

not drive the vehicle. Have the vehicle

inspected by an authorized HYUNDAI

dealer.

- It illuminates for approximately 3~6

seconds and then goes off.

śꢀ When there is a malfunction with the

SRS.

In this case, have the vehicle

inspected by an authorized HYUNDAI

dealer.

4-10

04

Dual-diagonal braking system

Anti-lock Brake System (ABS)

warning light

Your vehicle is equipped with dual-

diagonal braking system. This means you

still have braking on two wheels even if

one of the dual systems should fail.

With only one of the dual systems

working, more than normal pedal travel

and greater pedal pressure is required to

stop the vehicle.

Also, the vehicle will not stop in as short

a distance with only a portion of the

brake system working.

If the brakes fail while you are driving,

shift to a lower gear for additional engine

braking and stop the vehicle as soon as it

is safe to do so.

This warning light illuminates:

śꢀ When you set the ignition switch or

the Engine Start/Stop button to the

ON position.

- The ABS warning light illuminates

for about 3 seconds and then goes

off.

śꢀ Whenever there is a malfunction with

the ABS.

Note that the hydraulic braking

system will still be operational even if

there is a malfunction with the ABS.

If this occurs, have the vehicle

inspected by an authorized HYUNDAI

dealer.

WARNING

Parking Brake & Brake Fluid warning

Electronic Brake Force

Distribution (EBD) system

warning light

light

Driving the vehicle with a warning light

ON is dangerous. If the Parking Brake

& Brake Fluid warning light illuminates

with the parking brake released, it

indicates that the brake fluid level is

low.

When the ABS warning and

Parking Brake warning lights are on

simultaneously, it may indicate a

problem with the Electronic Brake Force

Distribution system.

If this occurs, have the vehicle

inspected by an authorized HYUNDAI

dealer.

If this occurs, have the vehicle inspected

by an authorized HYUNDAI dealer.

4-11

Instrument cluster

Electric Power Steering (EPS)

warning light

WARNING

Electronic Brake Force Distribution

(EBD) system warning light

This warning light illuminates:

śꢀ When you set the ignition switch or

the Engine Start/Stop button to the

ON position.

When both ABS and Parking Brake &

Brake Fluid warning lights are on, the

brake system will not work normally

and you may experience an unexpected

and dangerous situation during sudden

braking.

If this occurs, avoid high speed driving

and abrupt braking.

Have the vehicle inspected by an

authorized HYUNDAI dealer as soon as

possible.

- The electric power steering warning

light illuminates for about 3 seconds

and then goes off.

śꢀ Whenever there is a malfunction with

the electric power steering.

If this occurs, have the vehicle

inspected by an authorized HYUNDAI

dealer.

NOTICE

Electronic Brake Force Distribution

(EBD) system warning light

Charging system warning

light

When the ABS warning light is on

or both ABS and Parking Brake &

Brake Fluid warning lights are on, the

speedometer, odometer, or tripmeter

may not work. Also, the EPS warning

light may illuminate and the steering

effort may increase or decrease.

If this occurs, have the vehicle

inspected by an authorized HYUNDAI

dealer as soon as possible.

This warning light illuminates:

When there is a malfunction with either

the alternator or electrical charging

system.

If there is a malfunction with either the

alternator or electrical charging system:

1. Drive carefully to the nearest safe

location and stop your vehicle.

2. Turn the engine off and check the

alternator drive belt for looseness or

breakage.

If the belt is adjusted properly, there

may be a problem in the electrical

charging system.

If this occurs, have the vehicle

inspected by an authorized HYUNDAI

dealer as soon as possible.

4-12

04

Engine oil pressure warning

light

NOTICE

If the engine is not stopped

immediately after the Engine Oil

This warning light illuminates:

When the engine oil pressure is low.

Pressure warning light is illuminated,

severe damage could result.

If the engine oil pressure is low:

Low fuel level warning light

1. Drive carefully to the nearest safe

location and stop your vehicle.

This warning light illuminates:

When the fuel tank is nearly empty.

Add fuel as soon as possible.

2. Turn the engine off and check the

engine oil level (For more details,

refer to “Engine Oil” section in

chapter 9). If the level is low, add oil

as required.

If the warning light remains on after

adding oil or if oil is not available, have

the vehicle inspected by an authorized

HYUNDAI dealer as soon as possible.

Continued driving with the warning light

on may cause engine failure.

NOTICE

Driving with the Low Fuel Level warning

light on or with the fuel level below “E

or 0” can cause the engine to misfire

and damage the catalytic converter.

Information

When engine oil pressure decreases due to

insufficient engine oil, etc., the Engine Oil

Pressure warning light will illuminate. In

addition, the enhanced engine protection

system which limits engine power will

be activated. If the engine oil pressure is

restored, the Engine Oil Pressure warning

light and the enhanced engine protection

system will turn off. However, for gasoline

2.5 turbo engine and 2.5 gdi engine, when

the engine oil pressure is restored, the

warning light and the enhanced engine

protection system will turn off after the

engine is restarted.

4-13

Instrument cluster

Malfunction Indicator Lamp

(MIL)

Exhaust system (GPF)

warning light (for gasoline

engine, if equipped)

This indicator light illuminates:

śꢀ When you set the ignition switch or

the Engine Start/Stop button to the

ON position.

śꢀ This warning light illuminates, when

accumulated soot reaches a certain

amount.

śꢀ When this warning light illuminates, it

may turn off after driving the vehicle

at more than 50 mph (80km/h) for

about 30 minutes (above 3rd gear

with 1500 ~ 4000 engine rpm).

- The malfunction indicator light

illuminates for about 3 seconds and

then goes off.

śꢀ Whenever there is a malfunction with

either the emission control system or

the engine or the vehicle powertrain.

If this warning light blinks in spite

of the procedure (at this time LCD

warning message will be displayed),

have the GPF system checked by an

authorized HYUNDAI dealer.

If this occurs, have the vehicle

inspected by an authorized HYUNDAI

dealer.

NOTICE

If you continue to drive with the GPF

warning light blinking for a long time,

the GPF system can be damaged and

fuel consumption can worsen.

śꢀ Driving with the Malfunction

Indicator Lamp (MIL) on may cause

damage to the emission control

system which could affect drivability

and/or fuel economy.

śꢀ If the enhanced engine protection

system becomes activated due to

lack of engine oil, engine power

will be limited. If such condition

continues repeatedly, the

Malfunction Indicator Lamp will

illuminate.

NOTICE

If the Malfunction Indicator Lamp

(MIL) illuminates, potential catalytic

converter damage is possible which

could result in loss of engine power.

If this occurs, have the vehicle

inspected by an authorized HYUNDAI

dealer as soon as possible.

4-14

04

Electronic Parking Brake

(EPB) warning light

(if equipped)

Low tire pressure warning

light

This warning light illuminates:

śꢀ When you set the ignition switch or

the Engine Start/Stop button to the

ON position.

śꢀ When you set the ignition switch or

the Engine Start/Stop button to the

ON position.

- The low tire pressure warning light

illuminates for approximately 3

seconds and then goes off.

- The EPB warning light illuminates

for about 3 seconds and then goes

off.

śꢀ When one or more of your tires are

significantly underinflated. (The

location of the underinflated tires are

displayed on the LCD display.)

For more details, refer to “Tire Pressure

Monitoring System (TPMS)” section in

chapter 8.

śꢀ Whenever there is a malfunction with

EPB.

If this occurs, have the vehicle

inspected by an authorized HYUNDAI

dealer.

Information

This warning light remains ON after

blinking for approximately 60 seconds, or

repeatedly blinks ON and OFF in 3 second

intervals:

When there is a malfunction with the

TPMS.

The Electronic Parking Brake (EPB)

warning light may illuminate when

the Electronic Stability Control (ESC)

indicator light comes on to indicate that

ESC is not working properly. This does

not indicate malfunction of EPB.

If this occurs, have the vehicle inspected

by an authorized HYUNDAI dealer as

soon as possible.

AUTO HOLD indicator light

For more details, refer to “Tire Pressure

Monitoring System (TPMS)” section in

chapter 8.

This indicator light illuminates:

śꢀ [White] When you activate Auto Hold

by pressing the AUTO HOLD switch.

śꢀ [Green] When you stop the vehicle

completely by depressing the brake

pedal with Auto Hold activated.

WARNING

Safe Stopping

śꢀ The TPMS cannot alert you to severe

and sudden tire damage caused by

external factors.

śꢀ [Yellow] Whenever there is a

malfunction with the Auto Hold

function.

śꢀ If you notice any vehicle instability,

immediately take your foot off the

accelerator pedal, apply the brakes

gradually with light force, and slowly

move to a safe position off the road.

If this occurs, have the vehicle

inspected by an authorized HYUNDAI

dealer.

For more details, refer to “Electronic

Parking Brake (EPB)” section in chapter

6.

4-15

Instrument cluster

Forward Safety warning light

(if equipped)

Lane Safety indicator light

(if equipped)

This warning light illuminates:

śꢀ When you set the ignition switch or

the Engine Start/Stop button to the

ON position.

This indicator light illuminates:

śꢀ [Green] When the system operating

conditions are satisfied.

śꢀ [White] When the system operating

- The Forward Safety warning light

illuminates for approximately 3

seconds and then goes off.

conditions are not satisfied.

śꢀ [Yellow] Whenever there is a

malfunction with Lane Keeping Assist.

śꢀ Whenever there is a malfunction with

If this occurs, have the vehicle

inspected by an authorized HYUNDAI

dealer.

Forward Collision-Avoidance Assist.

If this occurs, have the vehicle inspected

by an authorized HYUNDAI dealer.

For more details, refer to “Forward

Collision-Avoidance Assist (FCA)”

section in chapter 7.

For more details, refer to “Lane Keeping

Assist (LKA)” section in chapter 7.

4 Wheel Drive (4WD) warning

light

This warning light illuminates:

Whenever there is a malfunction with the

4WD system.

If this occurs, have the vehicle inspected

by an authorized HYUNDAI dealer.

For more details, refer to “4 Wheel Drive

(4WD)” section in chapter 6.

4-16

04

4 Wheel Drive (4WD) LOCK

Indicator Light

LED headlight warning light

This indicator light illuminates:

śꢀ Once you set the ignition switch or

Engine Start/Stop Button to the ON

position.

This warning light illuminates:

śꢀ When you set the ignition switch or

the Engine Start/Stop button to the

ON position.

- It illuminates for approximately 3

seconds and then goes off.

- The LED headlight warning light

illuminates for approximately 3

seconds and then goes off.

śꢀ When you select 4WD Lock mode by

pressing the 4WD LOCK button.

śꢀ Whenever there is a malfunction with

the LED headlight.

- The 4WD LOCK mode is to increase

the drive power when driving on

wet pavement, snow covered roads

and/or off-road.

If this occurs, have the vehicle

inspected by an authorized HYUNDAI

dealer.

This warning light blinks:

Whenever there is a malfunction with a

LED headlight related part.

If this occurs, have the vehicle inspected

by an authorized HYUNDAI dealer.

NOTICE

Do not use 4WD LOCK mode on dry

paved roads or highway, it can cause

noise, vibration or damage of 4WD

related parts.

NOTICE

Continuous driving with the LED

Headlight warning light on or blinking

can reduce LED headlight life.

4-17

Instrument cluster

Icy road warning light

(if equipped)

Electronic Stability Control

(ESC) indicator light

This warning light is to warn the driver

the road may be icy.

This indicator light illuminates:

śꢀ When you set the ignition switch or

the Engine Start/Stop button to the

ON position.

When the temperature on the outside

temperature gauge is approximately

below 4°C (40°F), the Icy Road warning

light and Outside Temperature Gauge

blinks and then illuminates. Also, the

warning chime sounds 1 time.

You can activate or deactivate Icy Road

Warning function from the User Settings

menu in the cluster LCD display.

- The Electronic Stability Control

indicator light illuminates for about

3 seconds and then goes off.

śꢀ Whenever there is a malfunction with

ESC system.

If this occurs, have the vehicle

inspected by an authorized HYUNDAI

dealer.

Select:

-

6HWXSꢀƟꢀ8VHUꢀ6HWWLQJVꢀƟꢀ&OXVWHUꢀƟꢀ,F\ꢀ

Road Warning

This indicator light blinks:

While ESC is operating.

Information

For more details, refer to “Electronic

Stability Control (ESC)” section in

chapter 6.

If the Icy Road warning light appears

while driving, you should drive more

attentively and safely refraining from

over-speeding, rapid acceleration, sudden

braking or sharp turning, etc.

Electronic Stability Control

(ESC) OFF indicator light

(if equipped)

This indicator light illuminates:

śꢀ When you set the ignition switch or

the Engine Start/Stop button to the

ON position.

- The ESC OFF indicator light

illuminates for approximately 3

seconds and then goes off.

śꢀ When you deactivate ESC system by

pressing the ESC OFF button.

For more details, refer to “Electronic

Stability Control (ESC)” section in

chapter 6.

4-18

04

Immobilizer Indicator Light

(without smart key)

(if equipped)

Immobilizer Indicator Light

(with smart key)

(if equipped)

This indicator light illuminates:

śꢀ When the vehicle detects the

immobilizer in the key with the

ignition switch in the ON position.

This indicator light illuminates for up to

30 seconds:

śꢀ When the vehicle detects the smart

key in the vehicle with the Engine

Start/Stop button in the ACC or ON

position.

- At this time, you can start the

engine.

- The indicator light goes off after

starting the engine.

- At this time, you can start the

engine.

- The indicator light goes off after

starting the engine.

This indicator light blinks:

śꢀ When there is a malfunction with the

This indicator light blinks for a few

seconds:

immobilizer system.

In this case, have the vehicle

inspected by an authorized HYUNDAI

dealer.

śꢀ When the smart key is not in the

vehicle.

- At this time, you cannot start the

engine.

This indicator light illuminates for 2

seconds and goes off:

śꢀ If the smart key is in the vehicle and

the Engine Start/Stop button is ON,

but the vehicle cannot detect the

smart key.

In this case, have the vehicle

inspected by an authorized HYUNDAI

dealer.

This indicator light blinks:

śꢀ When there is a malfunction with the

immobilizer system.

In this case, have the vehicle

inspected by an authorized HYUNDAI

dealer.

4-19

Instrument cluster

Downhill Brake Control (DBC)

indicator light

AUTO STOP indicator light

This indicator light illuminates:

śꢀ When you set the ignition switch or

the Engine Start/Stop button to the

ON position.

This indicator light illuminates:

When the engine enters the Idle Stop

mode of ISG (Idle Stop and Go) system.

When the engine automatically starts,

the AUTO STOP indicator on the cluster

Illuminates to white.

- The downhill brake control indicator

light illuminates for about 3 seconds

and then goes off.

For more details, refer to "ISG (Idle Stop

and Go) system" section in chapter 6.

śꢀ When you activate the system by

pressing the DBC button.

This indicator light blinks:

When Downhill Brake Control system is

operating.

Information

When the engine automatically starts

by the ISG system, some warning lights

(ABS, ESC, ESC OFF, EPS or Parking

brake warning light) may turn on for a

few seconds. This happens because of

low battery voltage. It does not mean the

system has malfunctioned.

This indicator light illuminates yellow:

Whenever there is a malfunction with

Downhill Brake Control system.

If this occurs, have the vehicle inspected

by an authorized HYUNDAI dealer.

For more details, refer to "Downhill

Brake Control (DBC)“ section in chapter

6.

4-20

04

Turn signal indicator light

High Beam Assist indicator

light (if equipped)

This indicator light blinks:

When you operate the turn signal

indicator stalk.

This indicator light illuminates:

When the high-beam is on with the light

switch in the AUTO position.

śꢀ White: When High Beam Assist is

If any of the following occur, there may

be a malfunction with the turn signal

system.

ready to operate.

śꢀ Green: When High Beam Assist is

operating.

-

The turn signal indicator light

illuminates but does not blink

The turn signal indicator light blinks

rapidly

The turn signal indicator light does not

illuminate at all

If your vehicle detects oncoming or

preceding vehicles, High Beam Assist

will switch the high beam to low beam

automatically.

For more details, refer to “High Beam

Assist (HBA)” section in chapter 5.

If any of these conditions occur, have

the vehicle inspected by an authorized

HYUNDAI dealer.

Cruise Indicator Light

(if equipped)

High beam indicator light

This indicator light illuminates:

When the cruise control system is

enabled.

This indicator light illuminates:

For more details, refer to "Smart Cruise

Control (SCC)" in chapter 7.

śꢀ When the headlights are on and in the

high beam position

śꢀ When the turn signal lever is pulled

into the Flash-to-Pass position.

4-21

Instrument cluster

SPORT Mode Indicator Light

(if equipped)

SMART Mode Indicator Light

(if equipped)

This indicator light illuminates

When you select "SPORT" mode as drive

mode.

This indicator light illuminates:

When you select ''SMART" mode as drive

mode.

For more details, refer to "Drive Mode

Integrated Control System" in chapter

6.

For more details, refer to "Drive Mode

Integrated Control System'' in chapter

6.

Master warning light

This warning light illuminates:

When there is a malfunction in operation

in any of the following systems:

-

Forward Collision-Avoidance Assist

malfunction (if equipped)

Forward Collision-Avoidance Assist

radar blocked (if equipped)

Blind-Spot Collision Warning

malfunction (if equipped)

Blind-Spot Collision Warning radar

blocked (if equipped)

LED headlight malfunction

(if equipped)

High Beam Assist malfunction

(if equipped)

Smart Cruise Control with Stop & Go

malfunction (if equipped)

Smart Cruise Control with Stop & Go

radar blocked (if equipped)

Tire Pressure Monitoring System

(TPMS) malfunction

To identify the details of the warning,

look at the LCD display.

4-22

04

Key not in vehicle (for smart key

system)

This message is displayed if the smart

key is not in the vehicle when you leave

the vehicle with the Engine Start/Stop

button in the ON or Start position.

LCD display messages

Shift to P (for smart key system)

This message is displayed if you try to

turn off the vehicle without the gear in

the P (Park) position.

If this occurs, the Engine Start/Stop

button turns to the ACC position.

Always turn off the engine before leaving

your vehicle.

Low key battery (for smart key

system)

This message is displayed if the battery

of the smart key is discharged while

changing the Engine Start/Stop button to

the OFF position.

Key not detected (for smart key

system)

This message is displayed if the smart

key is not detected when you press the

Engine Start/Stop button.

Press START button again (for smart

key system)

This message is displayed if you were

unable to start the vehicle when the

Engine Start/Stop button was pressed.

Press START button while turning

wheel (for smart key system)

This message is displayed if the steering

wheel does not unlock normally when

the Engine Start/Stop button is pressed.

If this occurs, attempt to start the engine

by pressing the Engine Start/ Stop button

again.

You should press the Engine Start/Stop

button while turning the steering wheel

right and left.

If the warning message appears each

time you press the Engine Start/Stop

button, have the vehicle inspected by an

authorized HYUNDAI dealer.

Check steering wheel lock system

(for smart key system)

This message is displayed if the steering

wheel does not lock normally while the

Engine Start/Stop button is pressed to

the OFF position.

Press brake pedal to start engine (for

smart key system)

This message is displayed if the Engine

Start/Stop button changes to the ACC

position twice by pressing the button

repeatedly without depressing the brake

pedal.

You can start the vehicle by depressing

the brake pedal and then pressing the

Engine Start/Stop button.

4-23

Instrument cluster

Press START button with key

(for smart key system)

Battery discharging due to external

electrical devices (if equipped)

This message is displayed if you press

the Engine Start/Stop button while the

warning message “Key not detected” is

displayed.

At this time, the immobilizer indicator

light blinks.

This message is displayed if the 12V

battery voltage is weak due to any

non-factory electrical accessories (ex.

dashboard camera) while parking. Be

careful that the battery is not discharged.

If the message appears after removing

the non-factory electrical accessories,

have the vehicle inspected by an

authorized HYUNDAI dealer.

Check BRAKE SWITCH fuse

(for smart key system)

This message is displayed if the brake

switch fuse is disconnected.

You need to replace the fuse with a new

one before starting the engine.

If that is not possible, you can start the

engine by pressing the Engine Start/

Stop button for 10 seconds in the ACC

position.

Shift to P to start engine

(for smart key system)

This message is displayed if you try to

start the engine in any other position

except P (Park).

4-24

04

Door, Hood, Liftgate open indicator

Sunroof open indicator (if equipped)

OTM040032

OTM040034

This warning is displayed if any door or

hood or liftgate is left open. The warning

will indicate which door is open in the

display.

This warning is displayed if you turn off

the engine when the sunroof is open.

Close the sunroof securely before leaving

your vehicle.

Low tire pressure

CAUTION

Before driving the vehicle, you should

confirm that the door/ hood/liftgate are

fully closed.

Also, check there is no door/hood/

liftgate open warning light or message

displayed on the instrument cluster.

OTM040022L

This warning message is displayed if the

tire pressure is low. The corresponding

tire on the vehicle will be illuminated.

For more details, refer to “Tire Pressure

Monitoring System (TPMS)” section in

chapter 8.

4-25

Instrument cluster

Lights

Low washer fluid

This message is displayed if the washer

fluid level in the reservoir is nearly empty.

ꢀType A

ꢀType B

Have the washer fluid reservoir refilled.

Low fuel

This message is displayed if the fuel tank

is almost out of fuel.

When this message is displayed, the low

fuel level warning light in the cluster will

come on.

OJX1049007L

OJX1049062L

It is recommended to look for the nearest

fueling station and refuel as soon as

possible.

This indicator displays which exterior

light is selected using the lighting

control.

You can activate or deactivate Wiper/

Lights display function from the User

Settings menu in the cluster LCD display.

Select:

Low engine oil (if equipped)

This warning message is displayed when

the engine oil level should be checked.

If this warning message is displayed,

check the engine oil level as soon as

possible and add engine oil as required.

-

6HWXSꢀƟꢀ8VHUꢀVHWWLQJVꢀƟꢀ&OXVWHUꢀƟꢀ

Wiper/Lights display

Slowly pour the recommended oil little

by little into a funnel.

Wiper

Use only the specified engine oil. (Refer

to "Recommended Lubricants and

Capacities“ section in chapter 2.)

ꢀType A

ꢀType B

Do not overfill the engine oil. Make sure

the oil level is not above F (Full) mark on

the dipstick.

OJX1049008L

OJX1049063L

This indicator displays which wiper speed

is selected using the wiper control.

You can activate or deactivate Wiper/

Lights display function from the User

Settings menu in the cluster LCD display.

Select:

-

6HWXSꢀƟꢀ8VHUꢀVHWWLQJVꢀƟꢀ&OXVWHUꢀƟꢀ

Wiper/Lights display

4-26

04

Engine overheated / Engine has

overheated (if equipped)

This message is displayed when the

engine coolant temperature is above

248°F (120°C). This means that the

engine is overheated and may be

damaged.

Check headlight (if equipped)

This warning message is displayed if the

headlights are not operating properly.

In addition, if a specific lamp(turn signal

lamp etc.) is not operating properly, the

warning message according to a specific

lamp (turn signal lamp etc.) is displayed.

If your vehicle is overheated, refer to

“Overheating” section in chapter 8.

A corresponding bulb may need to be

replaced.

Make sure to replace the burned out

bulb with a new one of the same wattage

rating.

Check exhaust system (if equipped)

This message is displayed if there is a

problem with the GPF system. At this

time, the GPF warning light will also

blink. If this occurs, have the GPF system

checked by an authorized HYUNDAI

dealer.

Check turn signal (if equipped)

This message is displayed if the turn

signal lamps are not operating properly.

A lamp may need to be replaced.

Make sure to replace the burned out

bulb with a new one of the same wattage

rating.

GPF : Gasoline Particulate Filter

Check headlight LED (if equipped)

This message is displayed if there is a

problem with the LED headlight. Have

the vehicle inspected by an authorized

HYUNDAI dealer.

4-27

Instrument cluster

Check Forward Collision-Avoidance

Assist system (if equipped)

Check Driver Attention Warning

system (if equipped)

This warning message is displayed

if there is a problem with Forward

Collision-Avoidance Assist. Have the

vehicle inspected by an authorized

HYUNDAI dealer.

For more details, refer to “Forward

Collision-Avoidance Assist (FCA)” in

chapter 6.

This warning message is displayed if

there is a problem with Driver Attention

Warning. Have the vehicle inspected by

an authorized HYUNDAI dealer.

For more details, refer to “Driver

Attention Warning (DAW)” in chapter 6.

Check High Beam Assist system

(if equipped)

This warning message is displayed if

there is a problem with the High Beam

Assist. Have the vehicle inspected by an

authorized HYUNDAI dealer.

Check Lane Keeping Assist system (if

equipped)

This warning message is displayed if

there is a problem with Lane Keeping

Assist. Have the vehicle inspected by an

authorized HYUNDAI dealer.

For more details, refer to “High Beam

Assist (HBA)” in chapter 5.

For more details, refer to “Lane Keeping

Assist (LKA)” in chapter 6.

Check Smart Cruise Control system

(if equipped)

This warning message is displayed if

there is a problem with Smart Cruise

Control. Have the vehicle inspected by

an authorized HYUNDAI dealer.

Check Blind-Spot Collision Warning

system (if equipped)

This warning message is displayed

if there is a problem with Blind-Spot

Collision Warning. Have the vehicle

inspected by an authorized HYUNDAI

dealer.

For more details, refer to “Smart Cruise

Control (SCC)” in chapter 6.

For more details, refer to “Blind-Spot

Collision Warning (BCW) ” in chapter 6.

4-28

Instrument cluster -> Warning and indicator lights for Your Hyundai Santa Fe SUV 2023

Popular Manuals