Get When Driving -> Rear View Monitor Guide for Mazda Cx-5 SUV 2023

When Driving

Rear View Monitor (Mazda Connect (Type A))

Rear View Monitor (Mazda Connect (Type A))^*

The rear view monitor provides visual images of the rear of the vehicle when reversing.

WARNING

Always drive carefully conﬁrming the safety of the rear and the surrounding conditions by

looking directly with your eyes:

Reversing the vehicle by only looking at the screen is dangerous as it may cause an accident

or a collision with an object. The rear view monitor is only a visual assist device when

reversing the vehicle. The images on the screen may be diﬀerent from the actual conditions.

CAUTION

Do not use the rear view monitor under the following conditions: Using the rear view

monitor under the following conditions is dangerous and could result in injury or vehicle

damage or both.

Icy or snow-covered roads.

Tire chains or a temporary spare tire is installed.

The liftgate is not fully closed.

The vehicle is on a road incline.

When the display is cold, images may course across the monitor or the screen and may be

dimmer than usual, which could cause diﬃculty in conﬁrming the surrounding conditions

of the vehicle. Always drive carefully conﬁrming the safety of the rear and the surrounding

conditions by looking directly with your eyes.

Do not apply excessive force to the camera. The camera position and angle may deviate.

Do not disassemble, modify, or remove it as it may no longer be waterproof.

The camera cover is made of plastic. Do not apply degreasing agents, organic solvents,

wax, or glass coating agents to the camera cover. If any are spilled on the cover, wipe oﬀ

with a soft cloth immediately.

Do not rub the camera cover forcefully with an abrasive or hard brush. The camera cover or

lens may be scratched which might aﬀect the images.

NOTE



If water, snow, or mud is stuck on the camera lens, wipe it off using a soft cloth. If it

cannot be wiped off, use a mild detergent.

If the camera temperature changes rapidly (Hot to cold, cold to hot), the rear view



monitor may not operate correctly.

When replacing the tires, consult an Authorized Mazda Dealer. Replacing the tires could



result in deviation of the guide lines which appear on the display.

*Some models.

4-280

When Driving

Rear View Monitor (Mazda Connect (Type A))



If the vehicle's front, side, or rear has been involved in a collision, the alignment of the

rear view parking camera (location, installation angle) may have deviated. Always

consult an Authorized Mazda Dealer to have the vehicle inspected.

If “No camera signal.” is indicated in the display, there could be a problem with the

camera. Have your vehicle inspected at an Authorized Mazda Dealer.



Rear View Parking Camera Location

▼

Rear view parking camera

Switching to the Rear View Monitor Display

▼

Shift the selector lever to R with the ignition switched ON to switch the display to the rear

view monitor display.

NOTE

When the selector lever is shifted from R to another selector lever position, the screen

returns to the previous display.

4-281

When Driving

Rear View Monitor (Mazda Connect (Type A))

Displayable Range on the Screen

▼

The images on the screen may be different from the actual conditions.

(Screen display)

Garnish

Bumper

(Actual view)

Object

NOTE



The displayable range varies depending on the vehicle and road conditions.

The displayable range is limited. Objects under the bumper or around the bumper ends

cannot be displayed.



The distance appearing in the displayed image is different from the actual distance

because the rear view parking camera is equipped with a specific lens.

Some optionally installed vehicle accessories may be picked up by the camera. Do not

install any optional parts that can interfere with the camera view, such as illuminating

parts or parts made of reflective material.



It may be difficult to see the display under the following conditions, however, it does not

indicate a malfunction.



In darkened areas.

When the temperature around the lens is high/low.

When the camera is wet such as on a rainy day or during periods of high humidity.

When foreign material such as mud is stuck around the camera.



When the camera lens reflects sunlight or headlight beams.



Image display may be delayed if the temperature around the camera is low.

4-282

When Driving

Rear View Monitor (Mazda Connect (Type A))

Viewing the Display

▼

Guide lines which indicate the width of the vehicle (yellow) are displayed on the screen as a

reference to the approximate width of the vehicle in comparison to the width of the parking

space you are about to back into.

Use this display view for parking your vehicle in a parking space or garage.

a

b

a) Vehicle width guide lines (yellow)

These guide lines serve as a reference to the approximate width of the vehicle.

b) Distance guide lines.

These guide lines indicate the approximate distance to a point measured from the

vehicle's rear (from the end of the bumper).



The red line indicates the point about 0.5 m (19.7 in) from the rear bumper. The yellow

lines indicate the points about 1.0 m (39.4 in) and 2.0 m (78 in) from the rear bumper.

CAUTION

The guide lines on the screen are ﬁxed lines. They are not synced to the driver's turning of the

steering wheel. Always be careful and check the area to the vehicle's rear and the surrounding

area directly with your eyes while backing up.

Rear View Monitor Operation

▼

The operation of the rear view monitor when reversing the vehicle varies depending on the

traffic, road, and vehicle conditions. The amount of steering and the timing also varies

depending on conditions, so confirm the surrounding conditions directly with your eyes and

steer the vehicle in accordance with the conditions.

Be well aware of the above cautions prior to using the rear view monitor.

NOTE

Images displayed on the monitor from the rear view parking camera are reversed images

(mirror images).

1. Shift the selector lever to R to switch the display to the rear view monitor display.

4-283

When Driving

Rear View Monitor (Mazda Connect (Type A))

2. Confirming the surrounding conditions, reverse the vehicle.

(Display condition)

(Vehicle condition)

3. After your vehicle begins entering the parking space, continue backing up slowly so that

the distance between the vehicle width lines and the sides of the parking space on the

left and right are roughly equal.

4. Continue to adjust the steering wheel until the vehicle width guide lines are parallel to

the left and right sides of the parking space.

5. Once they are parallel, straighten the wheels and back your vehicle slowly into the

parking space. Continue checking the vehicle's surroundings and then stop the vehicle in

the best possible position.

(Display condition)

(Vehicle condition)

6. When the selector lever is shifted from R to another selector lever position, the screen

returns to the previous display.

4-284

When Driving

Rear View Monitor (Mazda Connect (Type A))

NOTE



If the parking space has division lines, straighten the wheels when the vehicle width

guide lines are parallel to them.

Because there may be a difference between the displayed image, such as indicated

below, and the actual conditions when parking, always verify the safety at the rear of

the vehicle and the surrounding area directly with your eyes.



In the image of the parking space (or garage) displayed on the screen, the back end

and distance guide lines may appear aligned in the monitor, but they may not

actually be aligned on the ground.

When parking in a space with a division line on only one side of the parking space,



the division line and the vehicle width guide line appear aligned in the monitor, but

they may not actually be aligned on the ground.

Variance Between Actual Road Conditions and Displayed Image

▼

Some variance occurs between the actual road and the displayed road. Such variance in

distance perspective could lead to an accident. Note the following conditions that may cause

a variance in distance perspective.

4-285

When Driving

Rear View Monitor (Mazda Connect (Type A))

When the vehicle is tilted due to the weight of passengers and load

When the vehicle rear is lowered, the object displayed on the screen appears farther than the

actual distance.

Variance

Object

When there is a steep grade behind the vehicle

When there is a steep upgrade (downgrade) behind the vehicle, the object displayed on the

screen appears farther (downgrade: closer) than the actual distance.

Appears

farther than

actual

Appears

closer than

actual

A

B

A

distance

Object on screen

Object at actual position

Object on screen

Object at actual

position

A: Distance between the vehicle and object displayed on the screen.

B: Actual distance between the vehicle and object.

4-286

When Driving

Rear View Monitor (Mazda Connect (Type A))

Three-dimensional object on vehicle rear

Because the distance guide lines are displayed based on a flat surface, the distance to the

three-dimensional object displayed on the screen is different from the actual distance.

(Screen display)

(Actual condition)

A

B

C

C B

(Actual distance) B>C=A

Sensed distance on screen A>B>C

Picture Quality Adjustment

▼

WARNING

Always adjust the picture quality of the rear view monitor while the vehicle is stopped:

Do not adjust the picture quality of the rear view monitor while driving the vehicle. Adjusting

the picture quality of the rear view monitor such as brightness, contrast, color, and tint while

driving the vehicle is dangerous as it could distract your attention from the vehicle operation

which could lead to an accident.

Picture quality adjustment must be done while the selector lever is in reverse (R).

There are four settings which can be adjusted including, brightness, contrast, tint, and color.

When adjusting, pay sufficient attention to the vehicle surroundings.

1. Select the

icon on the screen to display the tabs.

2. Select the desired tab item.

3. Adjust the brightness, contrast, tint, and color using the slider.

If you need to reset, press the reset button.

4. Select the

icon on the screen to close the tab.

4-287

When Driving

Rear View Monitor (Mazda Connect (Type B))

Rear View Monitor (Mazda Connect (Type B))^*

The rear view monitor provides visual images of the rear of the vehicle when reversing.

WARNING

Always drive carefully conﬁrming the safety of the rear and the surrounding conditions by

looking directly with your eyes:

Reversing the vehicle by only looking at the screen is dangerous as it may cause an accident

or a collision with an object. The rear view monitor is only a visual assist device when

reversing the vehicle. The images on the screen may be diﬀerent from the actual conditions.

CAUTION

Do not use the rear view monitor under the following conditions: Using the rear view

monitor under the following conditions is dangerous and could result in injury or vehicle

damage or both.

Icy or snow-covered roads.

Tire chains or a temporary spare tire is installed.

The liftgate is not fully closed.

The vehicle is on a road incline.

When the display is cold, images may course across the monitor or the screen and may be

dimmer than usual, which could cause diﬃculty in conﬁrming the surrounding conditions

of the vehicle. Always drive carefully conﬁrming the safety of the rear and the surrounding

conditions by looking directly with your eyes.

Do not apply excessive force to the camera. The camera position and angle may deviate.

Do not disassemble, modify, or remove it as it may no longer be waterproof.

The camera cover is made of plastic. Do not apply degreasing agents, organic solvents,

wax, or glass coating agents to the camera cover. If any are spilled on the cover, wipe oﬀ

with a soft cloth immediately.

Do not rub the camera cover forcefully with an abrasive or hard brush. The camera cover or

lens may be scratched which might aﬀect the images.

NOTE



If water, snow, or mud is stuck on the camera lens, wipe it off using a soft cloth. If it

cannot be wiped off, use a mild detergent.

If the camera temperature changes rapidly (Hot to cold, cold to hot), the rear view



monitor may not operate correctly.

When replacing the tires, consult an Authorized Mazda Dealer. Replacing the tires could



result in deviation of the guide lines which appear on the display.

*Some models.

4-288

When Driving

Rear View Monitor (Mazda Connect (Type B))



If the vehicle's front, side, or rear has been involved in a collision, the alignment of the

rear view parking camera (location, installation angle) may have deviated. Always

consult an Authorized Mazda Dealer to have the vehicle inspected.

If “No camera signal.” is indicated in the display, there could be a problem with the

camera. Have your vehicle inspected at an Authorized Mazda Dealer.



Rear View Parking Camera Location

▼

Rear view parking camera

Switching to the Rear View Monitor Display

▼

Shift the selector lever to reverse (R) position with the ignition switched ON to switch the

display to the rear view monitor display.

NOTE

When the selector lever is shifted from reverse (R) position to another selector lever

position, the screen returns to the previous display.

4-289

When Driving

Rear View Monitor (Mazda Connect (Type B))

Displayable Range on the Screen

▼

The images on the screen may be different from the actual conditions.

(Screen display)

Bumper

(Actual view)

Object

NOTE



The displayable range varies depending on the vehicle and road conditions.

If the camera lens is touched or there is any dirt on it, it could affect the screen image.

Wipe the lens using a soft cloth.

The displayable range is limited. Objects under the bumper or around the bumper ends

cannot be displayed.

The distance appearing in the displayed image is different from the actual distance

because the rear view parking camera is equipped with a specific lens.

Images displayed on the monitor from the rear view parking camera are reversed images

(mirror images).

Some optionally installed vehicle accessories may be picked up by the camera. Do not

install any optional parts that can interfere with the camera view, such as illuminating

parts or parts made of reflective material.



It may be difficult to see the display under the following conditions, however, it does not

indicate a malfunction.



In darkened areas.

When the temperature around the lens is high/low.

When the camera is wet such as on a rainy day or during periods of high humidity.



4-290

When Driving

Rear View Monitor (Mazda Connect (Type B))



When foreign material such as mud is stuck around the camera.

When the camera lens reflects sunlight or headlight beams.

The surroundings are illuminated by vehicle lights, fluorescent lights, or LED lights

(display may flicker).



Extremely small dark or white dots appear on the screen (dots may flicker).



Image display may be delayed if the temperature around the camera is low.

Viewing the Display

▼

Guide lines which indicate the width of the vehicle are displayed on the screen as a

reference to the approximate width of the vehicle in comparison to the width of the parking

space you are about to back into.

Use this display view for parking your vehicle in a parking space or garage.

a) Vehicle width guide lines

Guide lines serve as a reference to the approximate width of the vehicle.

b) Distance guide lines

These guide lines indicate the approximate distance to a point measured from the

vehicle's rear (from the end of the bumper).

The red line indicates the point about 0.5 m (19 in) from the rear bumper.

The yellow lines indicate the points about 1.0 m (39 in) and 2.0 m (78 in) from the rear

bumper.

Rear View Monitor Operation

▼

The operation of the rear view monitor when reversing the vehicle varies depending on the

traffic, road, and vehicle conditions. The amount of steering and the timing also varies

depending on conditions, so confirm the surrounding conditions directly with your eyes and

steer the vehicle in accordance with the conditions.

Be well aware of the above cautions prior to using the rear view monitor.

NOTE

Images displayed on the monitor from the rear view parking camera are reversed images

(mirror images).

4-291

When Driving

Rear View Monitor (Mazda Connect (Type B))

1. Shift the selector lever to reverse (R) position to switch the display to the rear view

monitor display.

2. Confirming the surrounding conditions, reverse the vehicle.

3. After your vehicle begins entering the parking space, continue backing up slowly so that

the distance between the vehicle width lines and the sides of the parking space on the

left and right are roughly equal.

(Display condition)

(Vehicle condition)

4. Continue to adjust the steering wheel until the vehicle width guide lines are parallel to

the left and right sides of the parking space.

5. Once they are parallel, straighten the wheels and back your vehicle slowly into the

parking space. Continue checking the vehicle's surroundings and then stop the vehicle in

4-292

When Driving

Rear View Monitor (Mazda Connect (Type B))

the best possible position. (If the parking space has division lines, check whether the

vehicle width guide lines are parallel to them.)

(Display condition)

(Vehicle condition)

6. When the selector lever is shifted from reverse (R) position to another selector lever

position, the screen returns to the previous display.

NOTE

Because there may be a difference between the displayed image, such as indicated below,

and the actual conditions when parking, always verify the safety at the rear of the vehicle

and the surrounding area directly with your eyes.



In the image of the parking space (or garage) displayed on the screen, the back end and

distance guide lines may appear aligned in the monitor, but they may not actually be

aligned on the ground.

4-293

When Driving

Rear View Monitor (Mazda Connect (Type B))



When parking in a space with a division line on only one side of the parking space, the

division line and the vehicle width guide line appear aligned in the monitor, but they may

not actually be aligned on the ground.

Variance Between Actual Road Conditions and Displayed Image

▼

Some variance occurs between the actual road and the displayed road. Such variance in

distance perspective could lead to an accident. Note the following conditions that may cause

a variance in distance perspective.

When the vehicle is tilted due to the weight of passengers and load

When the vehicle rear is lowered, the object displayed on the screen appears farther than the

actual distance.

Variance

Object

4-294

When Driving

Rear View Monitor (Mazda Connect (Type B))

When there is a steep grade behind the vehicle

When there is a steep upgrade (downgrade) behind the vehicle, the object displayed on the

screen appears farther (downgrade: closer) than the actual distance.

Appears

farther than

actual

Appears

closer than

actual

A

B

A

distance

Object on screen

Object at actual position

Object on screen

Object at actual

position

A: Distance between the vehicle and object displayed on the screen.

B: Actual distance between the vehicle and object.

Three-dimensional object on vehicle rear

Because the distance guide lines are displayed based on a flat surface, the distance to the

three-dimensional object displayed on the screen is different from the actual distance.

(Screen display)

Sensed distance on screen A>B>C

(Actual view)

A

C B

(Actual distance) B>C=A

4-295

When Driving -> Rear View Monitor for Your Mazda Cx-5 SUV 2023

Popular Manuals