220-240 V AC power supplies*
CAUTION
NOTE
NOTE
When the 220-240 V AC power supply is
not in use, be sure to cancel power supply by
pressing the 220-240 V AC power supply
switch, disconnect the plug and close the lid.
This will prevent the 220-240 V AC power
supply from becoming clogged and short cir-
cuiting.
Do not stand behind the exhaust pipe as the
engine may automatically start depending on
the condition. Heat from the exhaust could
lead to burns.
Make sure that the plug is inserted all the
way into the 220-240 V AC power supply
before using an electrical appliance.
Do not use an electrical appliance in the ve-
hicle which emits heat such as a heater. Heat
damage to interior parts could result.
Do not connect a malfunctioning electrical
appliance to the 220-240 V AC power sup-
ply. Doing so could damage the 220-240 V
AC power supply.
Never leave the vehicle, perform refueling
or washing the vehicle while using the
220-240 V AC power supply.
You may hear operating sounds such as
sounds from the cooling fan near the lug-
gage area when using the 220-240 V AC
power supply. This is normal.
Never use electrical appliance that is vulner-
able to vibration or heat in the cabin. When
exposed to strong direct sunlight, the cabin
will become extremely hot. It could cause
product failure.
Do not use the 220-240 V AC power supply
with the vehicle covered by a car cover.
When closing the window, door or tailgate,
be careful not to trap the power supply cord.
220-240 V AC power supply cannot be used
in the following cases.
automatically after stopping electricity sup-
ply, follow the procedures below.
1 Disconnect the plug of electrical ap-
l
l
l
l
. pliance.
2 Confirm the remaining quantity of
. the drive battery. When it is low,
charge the drive battery by using the
l
battery
SAVE/CHARGE
mode
switch, etc.
→ “Battery SAVE/CHARGE mode
switch” P. 7-27
l
l
l
l
l
l
→
“Normal charging (charging
8
method with rated AC 220-240V out-
let)” P. 3-10
→ “Quick charging (charging meth-
od with quick charger)” P. 3-17
3 Confirm that the ready indicator illu-
. minates. If not, start the Plug-in Hy-
brid EV System.
4 When the vehicle interior tempera-
. ture is too hot or too cold, adjust it
appropriately by using the air condi-
tioner.
5 Press the 220-240 V AC power sup-
. ply switch to turn it on.
6 Confirm that the indication lamp on
. the 220-240 V AC power supply
switch comes on and insert the plug
in the power outlet.
When the Plug-in Hybrid EV System
warning lamp is illuminated.
When the drive battery level display indi-
cates 0.
When the “PROPULSION POWER IS
REDUCED” warning display appears.
•
•
•
NOTE
Electrical appliance may not operate normal-
ly or electricity supply stops under the fol-
lowing conditions. You may hear an opera-
tion noise. This is normal.
l
l
The accessory socket and 220-240 V AC
power supplies can be used simultaneously.
Refer to “Accessory socket*” on page 8-75.
If the plug of the electrical appliance was
loose or wobbled when inserted in the outlet,
have the 220-240 V AC power supply re-
placed at a MITSUBISHI MOTORS Author-
ized Service Point.
l
l
When the power consumption of the elec-
trical appliance exceeds 1500 W.
When the vehicle interior temperature is
too hot or too cold.
•
•
When the 220-240 V AC power supply can-
not be used or is not returned to operation
For pleasant driving
8-79
OGGE20E1