Get Locking and unlocking -> Keyless entry system Guide for Mitsubishi Outlander SUV 2020

Electronic immobilizer (Anti-theft starting system)

Key number tag

CAUTION

Keyless entry system

Do not modify or add parts to the immobiliz-

er system. Doing so could cause the immo-

bilizer to malfunction.

The key number is stamped on the tag as in-

dicated in the illustration.

Press the remote control switch, and all doors

and the tailgate will be locked or unlocked as

desired.

Make a record of the key number and store

the key and key number tag in separate pla-

ces, so that you can order a key from your

MITSUBISHI MOTORS Authorized Service

Point in the event the original keys are lost.

NOTE

If the plug-in hybrid EV system does not

start, we recommend you to contact your

MITSUBISHI MOTORS Authorized Serv-

ice Point.

If you lose one of keyless operation keys,

contact your MITSUBISHI MOTORS Au-

thorized Service Point as soon as possible.

To obtain a replacement or extra spare key,

take your vehicle and all remaining keys to

your MITSUBISHI MOTORS Authorized

Service Point. All the keys have to be re-reg-

istered in the immobilizer computer unit.

The immobilizer can register up to four dif-

ferent keys.

1- LOCK switch

2- UNLOCK switch

3- Electric tailgate switch*

4- Indication lamp

Electronic immobilizer

5- Charging timer cancel switch*

(Anti-theft starting system)

NOTE

The electronic immobilizer has been de-

signed to significantly reduce the possibility

of vehicle theft. The purpose of the system is

to immobilize the vehicle if an invalid start is

attempted. A valid start attempt can only be

achieved by using a key “registered” to the

immobilizer system.

The charging lid is also locked/unlocked,

when the driver’s door is locked/unlocked.

Locking and unlocking

4-03

OGGE20E1

Keyless entry system

To lock

NOTE

The door and tailgate unlock function can be

set so that only the driver’s door unlocks

when the UNLOCK switch (2) is pressed

once.

If the door and tailgate unlock function is set

to work as described above, all the doors and

the tailgate unlock when the UNLOCK

switch is pressed two times in succession.

Refer to “Setting of door and tailgate unlock

function” on page 4-05.

If the UNLOCK switch (2) is pressed and no

door or tailgate is opened within approxi-

mately 30 seconds, relocking will automati-

cally occur.

If either of the following problems occurs,

the battery may be exhausted.

phone-link Display Audio (SDA) navigation

system, screen operations can be used to

make the adjustment. Refer to the separate

owner’s manual for details.

Press the LOCK switch (1). All the doors and

the tailgate will be locked. The turn-signal

lamps will blink once when the doors and the

tailgate are locked.

The time for automatic relocking can be

changed.

•

The confirmation function (flashing of the

turn-signal lamps) can be set to operate

only when the doors and backdoor are

locked or only when the doors and back-

door are unlocked.

To unlock

•

Press the UNLOCK switch (2). All the doors

and the tailgate will be unlocked. If the doors

and tailgate are unlocked when the front

room lamp switch is in the “DOOR” position

or the rear room lamp switch is in the middle

(•) position, the room lamp will illuminate for

approximately 15 seconds and the turn-signal

lamps will blink twice.

The position and tail lamps can also be set to

turn on for approximately 30 seconds. Refer

to “Instruments and controls: Welcome light”

on page 6-64.

The confirmation function (this indicates

locking or unlocking of the doors and tail-

gate with the blink of the turn-signal

lamps) can be deactivated.

The number of times the turn-signal

lamps are flashed by the confirmation

function can be changed.

•

The remote control switch is operated at

the correct distance from the vehicle, but

the doors and tailgate are not locked/

unlocked in response.

•

The outside rear-view mirrors automatically

retract or extend when the doors and tailgate

are locked or unlocked using the remote

control switches of the keyless entry system.

Refer to “Starting and driving: Outside rear-

view mirrors” on page 7-08.

The indication lamp (4) is dim or does not

come on.

•

For further information, please consult

your MITSUBISHI MOTORS Authorized

Service Point.

If you replace the battery yourself, refer to

“Procedure for replacing the remote con-

trol switch battery” on page 4-06.

It is possible to modify functions as follows:

For further information, please contact your

MITSUBISHI MOTORS Authorized Serv-

ice Point.

NOTE

The keyless entry system does not operate in

the following conditions:

For the operation of the Electric tailgate

switch (3), refer to “Electric tailgate” on

page 4-20.

The operation mode is not in OFF.

The LOCK switch (1) is pressed while a

door or the tailgate is open.

•

For the operation of the Charging timer can-

cel switch (5), refer to “MITSUBISHI Re-

mote Control” on page 3-20.

On vehicles equipped with the Smartphone-

link Display Audio (SDA) or the Smart-

4-04

Locking and unlocking

OGGE20E1

Keyless entry system

Number of

chimes

Condition

Step i:

NOTE

Press and hold the LOCK switch (1) for 4 to

8 seconds.

The remote control switch will operate with-

in approximately 4 m from the vehicle.

However, the operating range of the remote

control switch may change if the vehicle is

located near a power station, or radio/TV

broadcasting station.

If your remote control switch is lost or dam-

aged, please contact your MITSUBISHI

MOTORS Authorized Service Point for a re-

placement remote control switch.

If you wish to add a remote control switch,

we recommend you to contact your

MITSUBISHI MOTORS Authorized Serv-

ice Point.

The below remote control switches are avail-

able for your vehicle.

When the UNLOCK

switch (2), driver’s or

front passenger’s door

One chime [Fac- lock/unlock switch, or

tory setting]

tailgate open switch is

pressed one time, all

doors and the tailgate

unlock.

Step ii:

While holding the LOCK switch (1), press

the UNLOCK switch (2).

When the UNLOCK

switch (2) or the driver’s

door lock/unlock switch

is pressed one time, only

the driver’s door un-

locks. When the UN-

LOCK switch (2) or the

Step iii:

While holding the UNLOCK switch (2), re-

lease the LOCK switch (1).

Keyless operation key: up to four remote

control switches

•

Two chimes

driver’s

door

lock/

unlock switch is pressed

two times in succession,

all doors and the tailgate

unlock.

Setting of door and tailgate un-

lock function

The door and tailgate unlock function can be

set to the following two conditions.

Each time the door and tailgate unlock func-

tion is set, a chime will sound to tell you the

condition of the door and tailgate unlock

function.

Step iv:

Release the UNLOCK switch (2).

1. Put the operation mode in OFF.

2. Place the combination headlamps and

dipper switch in the “OFF” position, and

leave the driver’s door open.

3. Perform the following steps.

Steps ii to iv should be completed within

8 seconds.

NOTE

The number of chimes indicates the current

setting.

Locking and unlocking

4-05

OGGE20E1

Keyless entry system

1. Before replacing the battery, remove

static electricity from your body by

touching a metal grounded object.

2. Remove the emergency key from the

key.

NOTE

WARNING

Be sure to press the switches correctly when

If you think batteries might have been

swallowed or placed inside any part of

a person’s body, seek immediate medi-

cal attention.

•

performing the procedures. If you perform

the procedures incorrectly, the setting can be

changed unintentionally.

The charging lid is also unlocked, when the

driver’s door is unlocked.

Refer to “Emergency key” on page

4-14.

To prevent that can result in an explosion

or the leakage of flammable liquid or gas.

On vehicles equipped with the Smartphone-

Do not replace an incorrectly battery.

•

3. With the MITSUBISHI mark facing you,

insert the cloth covered tip of a straight

blade (or minus) screwdriver into the

notch in the remote control switch case

and use it to open the case.

link Display Audio (SDA) or the Smart-

phone-link Display Audio (SDA) navigation

system, screen operations can be used to

make the adjustment. Refer to the separate

owner’s manual for details.

Replace only with the same battery or

an equivalent type.

Do not dispose of a battery into fire or

incinerator, or mechanically crushing

or cutting of a battery.

•

Do not use, store in or bring into a bat-

tery where it may be exposed to ex-

tremely high temperature or extremely

low air pressure.

Procedure for replacing the re-

mote control switch battery

CAUTION

WARNING

When the remote control switch case is

opened, be careful to keep water, dust, etc.

out. Also, do not touch the internal compo-

nents.

Dispose of used batteries according to regu-

lations for the disposal of battery.

Do not swallow a coin type battery.

This product contains a coin type bat-

tery.

•

If a coin type battery is swallowed, it

can cause severe internal burns and can

lead to death.

NOTE

There have been cases where a swal-

lowed battery has caused severe inter-

nal burns in just 2 hours.

Keep new and used batteries away

from children.

If the remote control switch case does

not close securely, stop using the prod-

uct and keep it away from children.

Be sure to perform the procedure with the

NOTE

MITSUBISHI mark facing you. If the

MITSUBISHI mark is not facing you when

you open the remote control switch case, the

transmitter may come out.

•

You may purchase a replacement battery at

an electric appliance store.

MITSUBISHI MOTORS Authorized

Service Point can replace the battery for you

if you prefer.

4. Remove the used battery.

4-06

Locking and unlocking

OGGE20E1

Keyless operation system

5. Install a new battery with the + side (A)

up.

The driver should always carry the keyless

operation key. This key is necessary for lock-

ing and unlocking the doors and tailgate,

starting the Plug-in Hybrid EV System and

otherwise operating the vehicle, so before

locking and leaving the vehicle, be sure to

check that you have the keyless operation

key.

WARNING

When using electro-medical devices other

than implantable cardiac pacemakers or

implantable cardiovascular-defibrillators,

contact the electromedical device manu-

facturer ahead of time to determine the

affects of radio waves on the devices. Elec-

tromedical device operations could be ad-

versely effected by radio waves.

+ side

- side

WARNING

People with implantable cardiac pace-

Coin type battery

CR2032

You can limit the possible operations of

the keyless operation system in the fol-

lowing ways. (The keyless operation

system can be used as a keyless entry

system.) Please consult a MITSUBISHI

MOTORS Authorized Service Point.

• You can limit operations to locking

and unlocking the doors and tailgate.

• You can limit operations to starting

the Plug-in Hybrid EV System.

makers or implantable cardiovascular-de-

fibrillators should not go near the exterior

transmitters (A) or the interior transmit-

ters (B). The radio waves used by the key-

less operation system could adversely af-

fect implantable cardiac pacemakers or

implantable cardiovascular-defibrillators.

6. Close the case firmly.

7. Install the emergency key removed in

step 2.

8. Check the keyless operation function to

see that it works.

Keyless operation system

• The keyless operation system can be

disabled.

The keyless operation system allows you to

lock and unlock the doors and tailgate and

start the Plug-in Hybrid EV System simply

by carrying the keyless operation key with

you.

The keyless operation key can also be used as

the keyless entry system remote control

switch.

NOTE

The keyless operation key uses an ultra-

weak electromagnetic wave. In the following

cases, the keyless operation system may not

operate properly or may be unstable.

When there is equipment nearby that

emits strong radio waves, such as: a pow-

er station, a radio/TV broadcasting station

or an airport.

•

Refer to “Keyless entry system” on page

4-03.

Locking and unlocking

4-07

OGGE20E1

Keyless operation system

NOTE

The keyless operation system is carried

Because the keyless operation key continual-

ly receives signals, strong radio wave recep-

tion could affect battery wear. Do not leave

the key near a TV, personal computer, or

other electronic device.

If the keyless operation key battery is wear-

ing out or there are strong electromagnetic

waves or noise present, the operating range

may become smaller and operation may be-

come unstable.

•

together with a communications device

such as a cellular phone or radio set, or

with an electronic device such as a per-

sonal computer.

The keyless operation key is touching or

covered by a metal object.

A keyless entry system is being used

nearby.

When the keyless operation key battery is

worn out.

When the keyless operation key is placed

in an area with strong radio waves or

noise.

•

Operating range of the keyless

operation system

Operating range for locking

and unlocking the doors and

tailgate

The operating range is approximately 70 cm

from the driver’s door lock/unlock switch,

front passenger’s door lock/unlock switch,

and tailgate lock/unlock switch.

If you are carrying the keyless operation key,

enter the operating range of the keyless oper-

ation system, and press the driver’s or front

passenger’s door lock/unlock switch, the tail-

gate LOCK switch or the tailgate open

switch, the ID code for your key is verified.

You can lock and unlock the doors and tail-

gate and start the Plug-in Hybrid EV System

only if the ID codes of your keyless operation

key and the vehicle match.

In such cases, use the emergency key.

Refer to “To operate without using the

keyless operation function” on page

4-14.

Because the keyless operation key receives

signals in order to communicate with the

transmitters in the vehicle, the battery con-

tinually wears down regardless of keyless

operation key use. The battery life is 1 to 3

years, depending on usage conditions. When

the battery wears out, replace the battery ac-

cording to the description in this manual or

have it replaced at your MITSUBISHI

MOTORS Authorized Service Point.

Refer to “Procedure for replacing the remote

control switch battery” on page 4-06.

*: Forward direction

Operating range

4-08

Locking and unlocking

OGGE20E1

Keyless operation system

Operating range for starting the

Plug-in Hybrid EV System and

changing the operation mode

The operating range is the interior of the ve-

hicle.

NOTE

Locking and unlocking operate only when

you press a door or tailgate switch that de-

tects the keyless operation key.

Operation may not be possible if you are too

close to the front door, door window, or tail-

gate.

Even if the keyless operation key is within

70 cm of the driver’s door lock/unlock

switch, front passenger’s door lock/unlock

switch, or tailgate lock/unlock switch, if the

key is near to the ground or high up, the sys-

tem may not operate.

If the keyless operation key is within the op-

erating range, even someone not carrying the

key can lock and unlock the doors and tail-

gate by pressing the driver’s or front pas-

senger’s door lock/unlock switch, the tail-

gate lock switch or the tailgate open switch.

If a keyless operation key is too close to the

door or door window, it may be possible to

start the Plug-in Hybrid EV System or

change the operation mode even when the

key is outside the vehicles.

To operate using the keyless

operation function

NOTE

The charging lid is also locked/unlocked,

when the driver’s door is locked/unlocked.

Locking the doors and tailgate

When you are carrying the keyless operation

key, if you press the driver’s or front pas-

senger’s door lock/unlock switch (A), or the

tailgate LOCK switch (B) within the operat-

ing range, the doors and the tailgate are

locked.

*: Forward direction

Operating range

NOTE

The turn-signal lamps will blink once.

Even if it is within the operating range, if the

keyless operation key is in a small item

holder such as the glove box, on top of the

instrument panel, door pocket or in the lug-

gage area, it may be impossible to start the

Plug-in Hybrid EV System.

Locking and unlocking

4-09

OGGE20E1

Keyless operation system

Also refer to “Locking and unlocking: Doors,

Central door locks, Tailgate” on pages 4-14,

4-16 and 4-19.

Unlocking the doors and tail-

gate

NOTE

For vehicles equipped with the mirror retrac-

tor switch, the outside rear-view mirrors au-

tomatically retract when all the doors and

tailgate are locked using the keyless opera-

tion function.

Refer to “Starting and driving: Outside rear-

view mirrors” on page 7-08.

The keyless operation function does not op-

erate under the following conditions:

When you are carrying the keyless operation

key, if you press the driver’s or front pas-

senger’s door lock/unlock switch (A), or the

tailgate open switch (B) within the operating

range, all the doors and the tailgate are un-

locked.

If the front room lamp switch is in the

“DOOR” position or the rear room lamp

switch is in the middle ( ) position at this

time, the room lamp will turn on for 15 sec-

onds. The turn-signal lamps will blink twice.

If the driver’s or front passenger’s door lock/

unlock switch is pressed and any of the doors

or tailgate is not opened within approximate-

ly 30 seconds, relocking will automatically

occur.

Driver’s or front passenger’s door

lock/unlock switches

The keyless operation key is inside the

vehicle.

The operation mode of the power switch

is not in OFF.

•

A door or the tailgate is open or ajar.

The tailgate open switch (C) can be used to

check that the vehicle is locked properly.

Press the tailgate open switch within approx-

imately 3 seconds of locking the vehicle. If

you wait longer than 3 seconds and press the

tailgate open switch, the doors and tailgate

will be unlocked.

The time allowed for checking that the vehi-

cle is locked can be adjusted. For further in-

formation,

Tailgate switches

Also refer to “Locking and unlocking: Doors,

Central door locks, Tailgate” on page 4-14,

“Central door locks” on page 4-16 and

“Tailgate*” on page 4-19.

please

contact

your

MITSUBISHI MOTORS Authorized Serv-

ice Point.

Driver’s and front passenger’s door lock/unlock switches

On vehicles equipped with the Smartphone-

link Display Audio (SDA) or the Smart-

phone-link Display Audio (SDA) navigation

system, screen operations can be used to

make the adjustment. Refer to the separate

owner’s manual for details.

4-10

Locking and unlocking

OGGE20E1

Keyless operation system

Tailgate open switch

When locking:

The turn-signal

lamps will blink

once.

NOTE

In order to make it possible to check that the

doors and tailgate are locked, you cannot un-

lock them by using the tailgate open switch

for 3 seconds after locking them.

The time allowed for checking that the vehi-

cle is locked can be adjusted. For further in-

When unlocking:

The room lamp illu-

minates for approxi-

mately 15 seconds,

the turn-signal lamps

blink twice.

formation,

please

contact

your

MITSUBISHI MOTORS Authorized Serv-

ice Point.

On vehicles equipped with the Smartphone-

link Display Audio (SDA) or the Smart-

phone-link Display Audio (SDA) navigation

system, screen operations can be used to

make the adjustment. Refer to the separate

owner’s manual for details.

The time between unlocking and automatic

locking can be adjusted. Please consult a

MITSUBISHI MOTORS Authorized Serv-

ice Point.

On vehicles equipped with the Smartphone-

link Display Audio (SDA) or the Smart-

phone-link Display Audio (SDA) navigation

system, screen operations can be used to

make the adjustment. Refer to the separate

owner’s manual for details.

NOTE

Functions can be modified as stated below.

For further information, please contact your

MITSUBISHI MOTORS Authorized Serv-

ice Point.

On vehicles equipped with the Smartphone-

link Display Audio (SDA) or the Smart-

phone-link Display Audio (SDA) navigation

system, screen operations can be used to

make the adjustment. Refer to the separate

owner’s manual for details.

NOTE

The outside rear-view mirrors automatically

extend when all the doors and tailgate are

unlocked using the keyless operation func-

tion.

Refer to “Starting and driving: Outside rear-

view mirrors” on page 7-08.

The keyless operation function can be set so

that only the driver’s door unlocks when the

driver’s door lock/unlock switch is pressed.

If the keyless operation function is set to

work as described above, all the doors and

the tailgate unlock when the driver’s door

lock/unlock switch is pressed two times in

succession.

Set the confirmation function (blinking of

the turn-signal lamps) to operate only

when the vehicle is locked or only when

the vehicle is unlocked.

•

Disable the operation confirmation func-

tion (blinking of the turn-signal lamps).

Change the number of blinks for the oper-

ation confirmation function (blinks of the

turn-signal lamps).

•

Operation confirmation when locking and

unlocking

Operation can be confirmed as shown below.

However, the room lamp will only illuminate

if the front room lamp switch is in the

“DOOR” position or the rear room lamp

switch is in the middle (•) position.

Refer to “Setting of door and tailgate unlock

function” on page 4-05.

The keyless operation function does not op-

erate when the operation mode of the power

switch is not in OFF.

Locking and unlocking

4-11

OGGE20E1

Keyless operation system

Warning activation

In order to prevent vehicle theft or the accidental operation of the keyless operation system, the buzzer and the display on the information screen

in the multi-information display are used to alert the driver.

If a warning is activated, always check the vehicle and the keyless operation key. The warning is also displayed if there is a fault in the keyless

operation system.

Item

Display

Buzzer

Note (Solution)

Detection of failure

Inner buzzer sounds

once.

There is a fault in the keyless operation system.

Fall of battery voltage

Key not detected

Inner buzzer sounds

once.

The battery starts to run out, the warning is activated. (The

warning is not activated if the battery is completely dead.)

Inner buzzer sounds

once.

When the operation mode of the power switch is put in ACC or

ON from OFF or when the Plug-in Hybrid EV System is started,

the warning is activated, if any of the following conditions is oc-

curred.

Carrying another keyless operation key with a different

code, or the keyless operation key could be outside the op-

erating range.

The battery of the keyless operation key is dead.

Communication is blocked by electric wave environment.

Keyless operation key

reminder

Inner buzzer sounds ap- If the operation mode is in OFF and the driver’s door is opened

proximately 1 minute with the keyless operation key in the key slot, a warning is is-

Outer buzzer sounds ap- sued and the outer buzzer sounds for approximately 3 seconds

proximately 3 seconds

intermittently

and the inner buzzer sounds for approximately 1 minute to re-

mind you to remove the key. If the key removed from key slot,

the buzzer is stopped.

4-12

Locking and unlocking

OGGE20E1

Keyless operation system

Item

Display

Buzzer

Note (Solution)

Keyless operation key

take-out monitoring sys-

tem

Inner buzzer sounds

once.

Outer buzzer sounds in-

termittently.

When the vehicle is parked with the operation mode in any

mode other than OFF, if you close the door after opening

any of the doors and taking the keyless operation key out of

the vehicle, a warning is issued until the key is detected in

the vehicle.

If you take the keyless operation key out of the vehicle

through a window without opening a door, the keyless oper-

ation key take-out monitoring system does not operate.

It is possible to change the setting to make the keyless oper-

ation key take-out monitoring system operate if you take

the keyless operation key out from the vehicle through a

window without opening a door.

For further information, please contact a MITSUBISHI

MOTORS Authorized Service Point.

Even if you have the keyless operation key within the oper-

ating range for starting the Plug-in Hybrid EV System, if

the keyless operation key and vehicle ID codes cannot be

matched, for example due to the ambient environment or

electromagnetic conditions, the warning may be activated.

Key lock-in prevention

system

Inner buzzer sounds

once.

When the operation mode is in OFF, if you close all the

doors and the tailgate with the keyless operation key left in

the vehicle and you try to lock the doors and tailgate by

pressing the driver’s or front passenger’s door lock/unlock

switch, or the tailgate LOCK switch, a warning is issued

and you cannot lock the doors and tailgate.

Outer buzzer sounds ap-

proximately 3 seconds

intermittently

Make sure you have the keyless operation key with you be-

fore locking the doors. Even if you leave the keyless opera-

tion key inside the vehicle, it is possible that the doors will

lock depending on the surrounding environment and wire-

less signal conditions.

Locking and unlocking

4-13

OGGE20E1

Doors

Item

Display

Buzzer

Note (Solution)

Door ajar prevention

system

Inner buzzer sounds

once.

When the operation mode in OFF, if you try to lock the doors

and tailgate by pressing the driver’s or front passenger’s door

Outer buzzer sounds ap- lock/unlock switch, or the tailgate LOCK switch with one of the

proximately 3 seconds

intermittently

doors or the tailgate not completely closed, a warning is issued

and you cannot lock the doors and tailgate.

Operation mode OFF re-

minder system

Inner buzzer sounds

once.

When the operation mode is in any mode other than OFF, if you

try to lock the doors and tailgate by pressing the driver’s or front

Outer buzzer sounds ap- passenger’s door lock/unlock switch, or the tailgate LOCK

proximately 3 seconds

intermittently

switch, a warning is issued and you cannot lock the doors and

tailgate.

Refer to “Doors” on page 4-14.

To operate without using the

keyless operation function

NOTE

Only use the emergency key for emergen-

cies. If the keyless operation key battery

wears out, replace it as quickly as possible

so that you can use the keyless operation

key.

After using the emergency key, always re-

turn it into the keyless operation key.

Emergency key

The emergency key is built into the keyless

operation key. If the keyless operation func-

tion cannot be used, for example because the

keyless operation key battery has worn out or

the vehicle battery is flat, you can lock and

unlock the driver’s door with the emergency

key.

Doors

To use the emergency key (A), unlock the

lock knob (B) and remove it from the keyless

operation key (C).

CAUTION

Make sure the doors are closed: driving with

doors not completely closed is dangerous.

Never leave children in the vehicle unatten-

ded.

4-14

Locking and unlocking

OGGE20E1

Locking and unlocking -> Keyless entry system for Your Mitsubishi Outlander SUV 2020

Popular Manuals