Get Locking and unlocking -> Security alarm system Guide for Mitsubishi Outlander SUV 2020

Security alarm system*

The tailgate release (see illustration) is moun-

ted on the tailgate.

2. Move the lever (B) to open the tailgate.

Also, for vehicles equipped with the interior

alarm sensor, the alarm will be activated if

any of the following occurs:

Vehicles without

electric tailgate

Vehicles with

electrictailgate

Attempt to an unlawful moving of the

vehicle (the vehicle inclination detection

function)

Detection of a motion in the vehicle (the

interior intrusion detection function)

Disconnection of the battery terminal

The security alarm system is set to “active”.

When making changes to the settings, please

follow the procedure listed in the section ti-

tled “Changing the security alarm settings”

on page 4-29.

On vehicles equipped with the Smartphone-

link Display Audio (SDA) or the Smart-

phone-link Display Audio (SDA) navigation

system, screen operations can be used to

make the adjustment. Refer to the separate

owner’s manual for details.

3. Push out on the tailgate to open it.

You and your family should familiarise your-

selves with the location and operation of the

tailgate release.

CAUTION

Always keep the release lever lid on the tail-

To open

gate closed when driving so that your lug-

gage cannot accidentally bump against the

lever and open the tailgate.

1. Open the lid (A) inside of the tailgate.

Security alarm system*

CAUTION

Do not modify or add parts to the security

alarm system.

Doing so could cause the security alarm to

malfunction.

The security alarm system is for alerting the

surrounding area of suspicious behaviour to

prevent unlawful entry into the vehicle by op-

erating an alarm if a door, the tailgate or the

bonnet is opened when the vehicle has not

been unlocked using the keyless entry system

or the keyless operation function.

Locking and unlocking

4-27

OGGE20E1

Security alarm system*

The security alarm has four

modes:

NOTE

The alarm system will not be activated if the

Suffering a continuous impact or vibra-

tion by hail, thunder, etc.

•

doors and the tailgate have been locked us-

ing a key, the inside lock knob or the central

door lock switch (instead of the keyless en-

try system or the keyless operation func-

tion).

Air flows by the Remote Climate Control.

According to the situations, please deacti-

vate the vehicle inclination detection

function and the interior intrusion detec-

tion function.

•

System preparation mode (ap-

proximately 20 seconds)

(The buzzer sounds intermittently and the se-

curity indicator (A) blinks.)

For vehicles equipped with the interior alarm

sensor, if the turn-signal lamps do not blink

after the locking and unlocking operation us-

ing the keyless entry system or the keyless

operation function, the security alarm system

may be malfunctioning.

Have the vehicle inspected at

MITSUBISHI MOTORS Authorized Serv-

ice Point.

Refer to “To deactivate the vehicle incli-

nation detection function and the interior

intrusion detection function” on page

4-32.

For vehicles equipped with the interior alarm

sensor, the sensitivity of the interior intru-

sion detection function can be adjusted. For

details, please contact

a MITSUBISHI

If the confirmation function (blinking of the

turn-signal lamps by locking and unlocking

the doors and the tailgate) is deactivated, the

turn-signal lamps do not blink after the lock-

ing and unlocking operation.

MOTORS Authorized Service Point.

For information on the confirmation func-

tion, refer to “Keyless entry system” on page

4-03 and “To operate using the keyless oper-

ation function” on page 4-09.

For vehicles equipped with the interior alarm

sensor, the security alarm system could be

activated in the following situations.

The system preparation time extends from

the point at which all of the doors and the

tailgate are locked by pressing the LOCK

switch on the remote control switch or the

keyless operation function to the point at

which the system armed mode goes into ef-

fect.

Using a car wash

•

Taking the vehicle on a ferry

Parking in an automated car park

Leaving someone or a pet in the vehicle

Leaving a window or the sunroof open

Leaving an unstable object such as a stuf-

fed toy or accessory in the vehicle

4-28

Locking and unlocking

OGGE20E1

Security alarm system*

During this time, it is possible to temporarily

open a door or the tailgate without using the

keyless entry system or the keyless operation

function and without causing the alarm to

sound (for example, when you forget some-

thing inside the vehicle or realize that a win-

dow is open).

The turn-signal lamps blink and the horn (the

siren for vehicles equipped with the interior

alarm sensor) sounds, warning people around

the vehicle of an abnormal condition.

Changing the security alarm

settings

It is possible to set the security alarm to the

“active” mode or “inactive” mode.

Follow the procedure below.

1. Put the operation mode in OFF.

2. Place the lamp switch in the “OFF” posi-

tion, and leave the driver’s door open.

Refer to “Alarm activation” on page 4-33.

NOTE

The alarm will resume if unlawful actions

are taken again, even if the alarm has stop-

ped.

System armed mode

(The buzzer stops and the security indicator

continues to blink with the indicator’s re-

duced lit-up duration time.)

Once the system preparation mode has ended,

the system armed mode starts.

If an unlawful opening of any of the doors,

tailgate or bonnet is detected during the sys-

tem armed mode, the alarm will be activated

to warn people around the vehicle of an ab-

normal condition.

Also, for vehicles equipped with the interior

alarm sensor, if unlawful moving of the vehi-

cle is attempted or a vehicle intrusion is de-

tected, the alarm will be activated.

System cancellation

It is possible to cancel the system activation

during the system preparation mode or the

system armed mode.

In addition, it is possible to cancel the alarm

once it has been activated.

Refer to “Cancelling the system” on page

4-32, “Cancelling the alarm” on page 4-33.

NOTE

When lending the vehicle to another person

or allowing the vehicle to be driven by

someone who is unfamiliar with the security

alarm system, be sure to give the person a

proper explanation of the security alarm sys-

tem.

Alarm activation

Inside alarm (approximately 10 seconds):

The buzzer sounds, warning those inside the

vehicle of an abnormal condition.

(except for vehicles equipped with the interi-

or alarm sensor)

If a person who is unfamiliar with the securi-

ty alarm system accidentally unlocked the

vehicle, causing the alarm to sound, the

alarm would be a nuisance to people nearby.

Outside alarm (approximately 30 seconds):

Locking and unlocking

4-29

OGGE20E1

Security alarm system*

3. Pull the windscreen wiper and washer

switch towards you and hold it there.

(Since the operation mode in OFF, wash-

er fluid will not be sprayed.)

• Placing the lamp switch in any posi-

tion other than “OFF”.

• Allowing 30 seconds to pass without

making any changes to the settings.

NOTE

If anything with regard to making changes to

the security alarm system settings is hard to

understand,

MITSUBISHI MOTORS Authorized Serv-

ice Point.

Avoid leaving valuable items inside the ve-

hicle even when the security alarm system

has been set to the “active” mode.

please

consult

your

The settings mode can be toggled by

pressing the UNLOCK switch. The

mode can be confirmed from the number

of times the buzzer sounds.

Setting the system

Follow the procedure below to set the system

to the system armed mode.

1. Put the operation mode in OFF.

2. Exit the vehicle and close all of the

doors, tailgate and bonnet.

3. Press the LOCK switch (A) on the re-

mote control switch of the keyless oper-

ation key, the driver’s or front passeng-

er’s door lock/unlock switch (B), or the

tailgate LOCK switch (C) in order to

lock all the doors and the tailgate.

4. After approximately 10 seconds, the

buzzer will make a sound. Keep the

windscreen wiper and washer switch

pulled towards you. (If the windscreen

wiper and washer switch was released,

the setting change mode would be can-

celled. To start over, perform the proce-

dure again from step 3.)

5. When the buzzer stops, with the wind-

screen wiper and washer switch still

pulled towards you, press the UNLOCK

switch (A) on the remote control switch

to select the security alarm settings

mode.

Number of

times the

buzzer

Security alarm settings

mode

sounds

Alarm inactive

Alarm active

6. Any of the following operations can be

used to terminate the system settings

change mode.

• Releasing the windscreen wiper and

washer switch.

• Closing the driver’s door.

• Put the operation mode in ON or

ACC.

4-30

Locking and unlocking

OGGE20E1

Security alarm system*

By locking the vehicle using the keyless

entry system or the keyless operation

function, the system preparation mode is

activated.

The buzzer makes an intermittent beep-

ing sound and the security indicator (D)

in the instrument cluster flashes for con-

firmation.

NOTE

If the bonnet is open, the security indicator

illuminates, and the system does not enter

the system preparation mode.

When the bonnet is closed, the system enters

the system preparation mode, and after ap-

proximately 20 seconds the system enters

the system armed mode.

4. After approximately 20 seconds, the

buzzer stops, and when the blinking of

the security indicator starts to slow

down, the system armed mode goes into

effect.

Driver’s and front passenger’s door look/unlock switches*

The security indicator continues to blink

during the system armed mode.

NOTE

The security alarm system can be activated

when people are riding inside the vehicle or

when the windows are open. To prevent ac-

cidental activation of the alarm, do not set

the system to the system armed mode while

people are riding in the vehicle.

NOTE

The system preparation mode is not activa-

ted when the doors and the tailgate have

been locked using a method other than the

keyless entry system or the keyless operation

function (namely a key, the inside lock knob

or the central door lock switch).

Tailgate LOCK switch*

Avoid leaving valuable items inside the ve-

hicle even when the security alarm system

has been set to the “active” mode.

Locking and unlocking

4-31

OGGE20E1

Security alarm system*

The buzzer will sound once and the function

will be activated.

Opening any one of the doors or the tail-

gate, when the system is in the system

preparation mode.

Holding the keyless operation key and

pressing the driver’s or front passenger’s

door lock/unlock switch, or the tailgate

open switch to unlock the doors and the

tailgate.

To deactivate the vehicle incli-

nation detection function and

the interior intrusion detection

function*

The vehicle inclination detection function

and the interior intrusion detection function

can be deactivated when parking in automa-

ted car parks, when leaving pets in the vehi-

cle or when leaving the vehicle with the win-

dows slightly open.

NOTE

If the bonnet is opened during the system

preparation mode, the system preparation

mode is suspended.

The system returns to the system preparation

mode when the bonnet is closed.

If the auxiliary battery terminals are discon-

nected while the system is in the system

preparation mode, the memory will be

erased.

It is possible to register up to four remote

control switches for keyless operation sys-

tem.

1. Put the operation mode in OFF.

2. Raise and hold the wiper and washer

switch to the “MIST” position for ap-

proximately 3 seconds. The buzzer will

sound twice and the function will be de-

activated.

NOTE

The function will be activated again if the

following operation is performed.

If the doors and the tailgate are unlocked

using the keyless entry system or the key-

less operation function.

If the operation mode is put in ON or

ACC.

•

To activate the function again, raise and hold

the wiper and washer switch to the “MIST”

position for approximately 3 seconds.

As long as they are registered, any of the re-

mote control switches, other than the one

used to activate the system, can be used to

cancel the system.

Cancelling the system

The following methods can be used to cancel

the system when it is in the system prepara-

tion mode or the system armed mode.

If you want to register additional remote

control switches, please contact

MITSUBISHI MOTORS Authorized Serv-

ice Point.

Pressing the UNLOCK switch on the re-

mote control switch.

Putting the operation mode in ON.

4-32

Locking and unlocking

OGGE20E1

Security alarm system*

with the interior alarm sensor) will

sound intermittently.

Alarm activation

NOTE

When the system is in the system armed

mode, the alarm will be activated as follows

if the vehicle is unlocked or if any of the

doors, tailgate or bonnet is opened using a

method other than the keyless entry system or

the keyless operation function.

1. The inside alarm will be activated for

approximately 10 seconds. (except for

vehicles equipped with the interior alarm

sensor)

The activation distance for keyless entry sys-

tem is approximately 4 m.

If it is not possible to lock or unlock the ve-

hicle by pressing the switch at the correct

distance or the security alarm system cannot

be set or cancelled using the switch, the bat-

tery may need to be replaced.

Refer to “Procedure for replacing the remote

control switch battery” on page 4-06.

If the UNLOCK switch on the remote con-

trol switch, or the driver’s or front passeng-

er’s door lock/unlock switch is pressed and

no door or the tailgate is opened within 30

seconds, the doors and the tailgate will auto-

matically relock. In this case as well, the

system preparation mode will go into effect.

The time between pressing the UNLOCK

switch on the remote control switch, or the

driver’s or front passenger’s door lock/

unlock switch and automatic locking can be

NOTE

If the bonnet is opened during the system

3. The alarm will resume if unlawful ac-

tions are taken again, even if the alarm

has stopped.

armed mode, the vehicle outside alarm oper-

ates immediately, without the vehicle inside

alarm operating.

The time for the vehicle inside alarm can be

adjusted. Please consult

MITSUBISHI

Cancelling the alarm

It is possible to halt the activation of an alarm

using the following methods:

adjusted. Please consult

MOTORS Authorized Service Point.

a MITSUBISHI

MOTORS Authorized Service Point.

On vehicles equipped with the Smartphone-

link Display Audio (SDA) or the Smart-

phone-link Display Audio (SDA) navigation

system, screen operations can be used to

make the adjustment. Refer to the separate

owner’s manual for details.

2. The alarm will be activated for approxi-

mately 30 seconds.

The turn-signal lamps will blink, and the

horn (the siren for vehicles equipped

Pressing the LOCK or UNLOCK switch

on the remote control switch.

(After pressing the LOCK switch, the

vehicle will lock if all the doors and the

tailgate are closed, after which the sys-

tem preparation mode will once again go

into effect.)

Putting the operation mode in ON.

Locking and unlocking

4-33

OGGE20E1

Electric window control

Holding the keyless operation key and

Driver’s switches

Electric window control switch

Each door window opens or closes while the

corresponding switch is operated.

locking or unlocking the doors and the

tailgate using the keyless operation func-

tion.

The driver’s switches can be used to operate

all door windows. A window can be opened

or closed by operating the corresponding

switch.

Press the switch down to open the window,

and pull up the switch to close it.

If the switch for the driver’s window is fully

pressed down/pulled up, the door window au-

tomatically opens/closes completely.

If you want to stop the window movement,

operate the switch lightly in the reverse direc-

tion.

Driver’s switch RHD

Driver’s switch LHD

NOTE

Even if a door or the tailgate is closed while

the inside alarm is activating, this will not

cancel the alarm activation. (except for vehi-

cles equipped with the interior alarm sensor)

When the operation mode is put in ON, the

buzzer sounds four times. This operation in-

dicates that the alarm was activated while

the vehicle was parked.

Please check the inside of the vehicle to con-

firm that nothing was stolen.

Even if the auxiliary battery is disconnected,

the alarm activation memory will not be

erased.

1- Driver’s door window

2- Front passenger’s door window

3- Rear left door window

4- Rear right door window

5- Lock switch

NOTE

If the switch is operated continuously, the

electric window protection function will ac-

tivate and the door window may not be

opened and closed automatically even if the

switch is fully pressed down/pulled up.

In such a case, pull up the door window

switch until the window has been fully

closed.

Electric window control

WARNING

The electric windows can only be operated

with the operation mode in ON.

Before operating the electric window con-

trol, make sure that nothing can get trap-

ped (head, hand, finger, etc.).

You should now be able to operate the door

window in the normal fashion.

Never leave the vehicle without removing

the key.

Passenger’s switches

Never leave a child (or other person who

The passenger’s switches can be used to op-

erate the corresponding passenger’s door

windows.

might not be capable of safe operation of

the electric window control) in the vehicle

alone.

4-34

Locking and unlocking

OGGE20E1

Locking and unlocking -> Security alarm system for Your Mitsubishi Outlander SUV 2020

Popular Manuals