Get Starting and driving -> Cruise control Guide for Mitsubishi Outlander SUV 2020

Cruise control*

ASC OFF indicator

NOTE

CAUTION

The system may be malfunctioning.

Park your vehicle in a safe place and stop

the Plug-in Hybrid EV System.

Restart the Plug-in Hybrid EV System and

check whether the display/indicator goes

out. If they go out, there is no abnormal con-

dition. If they do not go out or appear fre-

quently, it is not necessary to stop the vehi-

cle immediately, but we recommend you to

have your vehicle inspected.

This indicator will turn on

when the ASC is turned off

with the ASC OFF switch.

The indicator may turn on when you start

the Plug-in Hybrid EV System. This means

that the battery voltage momentarily drop-

ped when the Plug-in Hybrid EV System

was started. It does not indicate a malfunc-

tion, provided that the indicator goes out im-

mediately.

CAUTION

When

indicator blinks, ASC is operating,

which means that the road is slippery or that

your vehicle’s wheels are beginning to slip.

If this happens, drive slower with less accel-

erator input.

If the temperature in the braking system con-

tinues to increase due to continuous brake

control on a slippery road surface, the in-

dicator will blink. To prevent the brake sys-

tem from overheating, the brake control of

the traction control function will be tempora-

rily suspended.

ASC warning lamp/display

If an abnormal condition occurs in the sys-

tem, the following warning lamp/warning

display will turn on.

Cruise control*

Cruise control is an automatic speed control

system that keeps a set speed. It can be acti-

vated at approximately 40 km/h (25 mph) or

more.

Warning lamp

- ASC operation indicator

The Plug-in Hybrid EV System control of

the traction control function and normal

brake operation will not be affected. Park

your vehicle in a safe place. When the tem-

perature in the braking system has come

down, the indicator will be turned off and

the traction control function will start operat-

ing again.

- ASC OFF indicator

Warning display

CAUTION

When you do not wish to drive at a set

speed, turn off the cruise control for safety.

Do not use cruise control when driving con-

ditions will not allow you to stay at the same

speed, such as in heavy traffic or on roads

that are winding, icy, snow-covered, wet,

slippery, on a steep downhill slope.

7-44

Starting and driving

OGGE20E1

Cruise control*

C- "RES +" switch

NOTE

Used to increase the set speed and to re-

turn to the original set speed.

D- “CANCEL” switch

Cruise control may not be able to keep your

speed on uphills or downhills.

Your speed may decrease on a steep uphill.

You may use the accelerator pedal if you

want to stay at your set speed.

Used to deactivate the set speed driving.

2. Accelerate or decelerate to your desired

speed, then push down and release the

"SET -" switch (B). The vehicle will

then maintain the desired speed.

The “SET” indicator appears on the in-

formation screen in the meter cluster.

Your speed may increase to more than the

set speed on a steep downhill. You must use

the brake to control your speed. As a result,

the set speed driving is deactivated.

The regenerative level B0 or B1 cannot be

selected under the cruise control. The buzzer

sounds if you try to select these levels.

NOTE

When operating the cruise control switches,

press the cruise control switches correctly.

The set speed driving may be deactivated

automatically if two or more switches of the

cruise control are pressed at the same time.

Cruise control switches

To activate

1. With the operation mode in ON, press

the CRUISE CONTROL ON/OFF

switch (A) to turn on the cruise control.

The indicator display in the meter cluster

will come on.

NOTE

When you release the "SET -" switch (B),

the vehicle speed will be set.

A- CRUISE CONTROL ON/OFF switch

Used to turn on and off the cruise con-

trol.

To increase the set speed

There are 2 ways to increase the set speed.

B- "SET -" switch

Used to reduce the set speed and to set

the desired speed.

Starting and driving

7-45

OGGE20E1

Cruise control*

When you reach your desired speed, release

the switch. Your new cruising speed is now

set.

"RES +" switch

Accelerator pedal

Push up and hold the "RES +" switch (C)

while driving at the set speed, and your speed

will then gradually increase.

When you reach your desired speed, release

the switch. Your new cruising speed is now

set.

While driving at the set speed, use the accel-

erator pedal to reach your desired speed and

then push down the "SET -" switch (B) and

release the switch momentarily to set a new

desired cruising speed.

To slow down your speed in small amounts,

push down the "SET -" switch (B) for less

than approximately 1 second and release it.

Each time you push down the "SET -" switch

(B), your vehicle will slow down by approxi-

mately 1.6 km/h (1 mph).

To decrease the set speed

There are 2 ways to decrease the set speed.

To increase your speed in small amounts,

push up the "RES +" switch (C) for less than

approximately 1 second and release it.

Each time you press the "RES +" switch (C),

your vehicle will go approximately 1.6 km/h

(1 mph) faster.

"SET -" switch

Push down and hold the "SET -" switch (B)

while driving at the set speed, and your speed

will slow down gradually.

7-46

Starting and driving

OGGE20E1

Cruise control*

Refer to “To resume the set speed” on page

7-48.

Brake pedal

To temporarily increase or de-

crease the speed

While driving at the set speed, use the brake

pedal, which disengages the cruise control,

then push down the "SET -" switch (B) and To temporarily increase the

release the switch momentarily to set a new speed

desired cruising speed.

Depress the accelerator pedal as you would

normally. When you release the pedal, you

will return to your set speed.

To deactivate

The set speed driving can be deactivated as

follows:

Press the CRUISE CONTROL ON/OFF

switch (A) (Cruise control will be turned

off.)

Press the “CANCEL” switch (D).

NOTE

In some driving conditions, the set speed

driving may be deactivated. If this happens,

refer to “To activate” on page 7-45 and re-

peat the speed setting procedure.

To temporarily decrease the

speed

Depress the brake pedal to decrease the

speed. To return to the previously set speed,

push up the "RES +" switch (C).

Starting and driving

7-47

OGGE20E1

Cruise control*

Depress the brake pedal.

WARNING

NOTE

Although the set speed driving will be de-

activated when shifting to the “N” (NEU-

TRAL) position, never move the selector

lever to the “N” (NEUTRAL) position

while driving.

The selector lever is shifted to “B” when

the select position is in “R”.

•

To resume the set speed

You would have no regenerative brake

and could cause a serious accident.

If the set driving speed is deactivated by the

condition described in “To deactivate” on

page 7-47, you can resume the previously set

speed by pushing up the "RES +" switch (C)

while driving at a speed of approximately

40 km/h (25 mph) or higher. The “SET” indi-

cator appears on the information screen in the

meter cluster.

CAUTION

When the set speed driving is deactivated

automatically in any situation other than

those listed above, there may be a system

malfunction.

The set speed driving is deactivated automat-

ically in any of the following ways.

Press the CRUISE CONTROL ON/OFF

switch to turn off the cruise control and have

your vehicle inspected by a MITSUBISHI

MOTORS Authorized Service Point.

When your speed slows to approximate-

ly 15 km/h (9 mph) or more below the

set speed because of a hill, etc.

When your speed slows to approximate-

ly 40 km/h (25 mph) or less.

NOTE

When the Active Stability Control

(ASC) starts operating.

You cannot operate the regenerative brake

while the adaptive cruise control system

(ACC) is operating.

If you perform the following operation, the

buzzer may sound and the select position

may automatically shift to “N” position.

Refer to “Active stability control (ASC)”

on page 7-42.

The electrical parking switch is pressed

during driving.

The selector lever is shifted to “R” during

driving forward.

The selector lever is shifted to “D” during

driving backward.

•

Under either of the following conditions,

however, using the switch does not allow you

to resume the previously set speed. In these

situations, repeat the speed setting procedure:

The CRUISE CONTROL ON/OFF

switch is pressed.

7-48

Starting and driving

OGGE20E1

Speed Limiter*

The operation mode is put in OFF.

The indicator display goes off.

In this case, when vehicle speed keeps ex-

ceeding set speed about +3 km/h (2 mph) for

about 30 seconds after the alert message is

appeared, beep alert is sounded for about 10

seconds at the most.

If the vehicle speeds decreases less than set

speeds after the alert message is appeared,

the message is disappeared. When beep alert

is sounding, the beep alert also goes off.

A- SPEED LIMITER ON/OFF switch

To turn on/off the Speed Limiter.

B- SET - switch

To set the current vehicle speed to a set

speed decrease the set speed.

C- RES + switch

Speed Limiter*

The Speed Limiter is a driver assist function

to prevent from exceeding the speed set by

driver while Plug-in Hybrid EV System pow-

er control.

To resume the Speed Limiter with set

speed memorized or increase the set

speed.

D- CANCEL switch

To cancel the Speed Limiter.

NOTE

CAUTION

Because the system does not use service

brake (hydraulic brake), the vehicle speed

may exceed the set speed on the downhill.

If a driver wants to keep the vehicle speed in

such a situation, he/she must put on a service

brake.

However, this gives priority to audio and

visual signal of safety reasons or driver’s de-

mand.

NOTE

Press the switch one by one.

The Speed Limiter may be cancelled auto-

matically, if two or more switches are press-

ed at the same time.

Speed Limiter control switches

There are 4 switches which relate to the

Speed Limiter on the steering wheel.

If the vehicle speed exceeds the set speed

(about 3 km/h (2 mph)), the indicator will

brink in the combination meter.

If the vehicle speed exceeds the set speed

about +3 km/h (2 mph) more than about 5

seconds after indicated alert message, beep

alert is sounded for about 10 seconds at the

most.

While running without alert message, if you

decrease the set speed and vehicle speed is

more than set speed about +3 km/h (2 mph),

alert message is displayed but beep alert is

delayed.

Starting and driving

7-49

OGGE20E1

Starting and driving -> Cruise control for Your Mitsubishi Outlander SUV 2020

Popular Manuals