Get Starting and driving -> Cruise control system operations Guide for Nissan Juke SUV 2020

CRUISE CONTROL (where fitted)

NOTE

–

When driving on slippery (rain, snow, ice,

etc.) roads

CRUISE CONTROL SYSTEM

OPERATIONS

If your vehicle is fitted with Intelligent Cruise Con-

trol (ICC) or ProPILOT, refer to the dedicated sec-

tion later in this manual for information on Cruise

Control.

CAUTION

On manual transmission models, do not shift into

N (Neutral) without depressing the clutch pedal

when the cruise control is set. Should this occur,

depress the clutch pedal and turn the cruise con-

trol main switch off immediately. Failure to do so

may cause engine damage.

ICC: See “Intelligent Cruise Control (ICC) and

Steering Assist (where fitted) (on Manual

Transmission vehicles)” later in this section.

•

ProPILOT: See “ProPILOT (where fitted)” later in

this section.

•

The cruise control system allows driving at constant

speeds without keeping your foot on the accelera-

tor pedal.

When the cruise control system is on the speed lim-

iter cannot be operated.

NIC4320

The cruise control system operation switches are

located on the steering wheel (right side).

<CANCEL> switch

➀

WARNING

<RES/+> (Resume) switch

<SET/—> switch

The cruise control system ONLY maintains a

•

The cruise control system operating condition is

shown in the vehicle information display.

constant vehicle speed, it does not replace the

driver.

Speed limiter main “ON/OFF” switch

(For details, see “Speed limiter (where fitted)”

later in this section) (where fitted)

➁

➂

PRECAUTIONS ON CRUISE

CONTROL

Always observe the posted speed limits and

do not set the speed above them.

•

Do not use the cruise control system when

The cruise control system will be automatically

•

Cruise control main “ON/OFF” switch

driving under the following conditions. Doing

so could cause a loss of vehicle control and

result in an accident.

cancelled when there is a malfunction. Have the

system checked by a NISSAN dealer or qualified

workshop.

–

When it is not possible to keep the vehicle

at a constant speed

To properly set the cruise control system, per-

form the steps as described in “Setting a cruis-

ing speed” later in this section.

•

–

When driving in heavy traffic

When driving in traffic that varies speed

When driving in windy areas

When driving on winding or hilly roads

NIC3814

Before setting speed

232 Starting and driving

Changing a cruising speed

Use any one of the following methods to change

the cruising speed.

Cancelling the cruise control system

To cancel a set speed limit, push the <CANCEL>

switch

➀

The cruise control symbol

and the set speed

➃

Slow the vehicle as normal using the footbrake

•

value

play turn grey.

at the top of the vehicle information dis-

➄

pedal.

When the vehicle reaches the desired cruising

speed, push and release the <SET> switch B .

The cruise control system will also be cancelled au-

tomatically by any of the following:

The new set speed value will be displayed in the

top of the vehicle information display.

Pressing the footbrake pedal.

•

Press the accelerator pedal.

NIC3815

Pressing the clutch pedal.

•

When the vehicle reaches the desired cruising

After setting speed

Cruise control symbol

Shifting the shift lever to the N (Neutral) posi-

tion. First depress clutch pedal.

•

speed, push and release the <SET> switch B .

The new set speed value will be displayed in the

top of the vehicle information display.

➃

➄

If the vehicle slows down more than approxi-

mately 12 km/h (8 MPH) below the set speed.

•

Set speed value

Push and release the <RES> (resume) A switch

to increase or the <SET> switch B to decrease

the set speed in steps of 1 km/h (1 MPH).

The new set speed value will be displayed in the

top of the vehicle information display.

Turning the cruise control system on

Resuming a previous cruising speed

Push the cruise control main switch . The cruise

➂

If the cruising speed has been cancelled, the last set

speed value will be stored in the cruise control sys-

tem memory and displayed in grey at the top of the

vehicle information display. This cruising speed can

be reactivated by pressing the <RES> (Resume)

control symbol

set speed value [— — —]

information display.

appears together with a blank

➃

at the top of the vehicle

➄

Push and hold the <RES> (resume) A switch or

Setting a cruising speed

the <SET> switch B . The vehicle speed will in-

switch A .

1. Accelerate to the desired cruising speed.

crease or decrease to the new set speed.

The new set speed value will be displayed in the

top of the vehicle information display.

If the vehicle speed is less than a minimum set

speed, it will not be possible to resume to the

cruising speed.

2. Push the <SET> switch B and release it.

3. The cruise control symbol changes to green

➃

with the set speed value (desired cruising speed)

in the top of the vehicle information display.

Passing another vehicle

➄

Depress the accelerator pedal to accelerate. After

releasing the accelerator pedal, the vehicle will re-

turn to the previously set speed.

4. Take your foot off the accelerator pedal.

The vehicle will maintain the set speed.

If the vehicle speed is less than the minimum set

speed, it will not be possible to set the cruise con-

trol system.

The set speed value

will flash until the vehicle

➄

returns to the previously set speed.

Starting and driving 233

SPEED LIMITER (where fitted)

NOTE

When additional floor mats are used, be sure

that they are correctly secured and that they

cannot interfere with the accelerator pedal.

Mats not adapted to the vehicle may prevent

proper operation of the speed limiter.

Turn the cruise control system off

The cruise control system will be turned off when

one of the following operations is performed:

•

If your vehicle is fitted with ProPILOT or Intelli-

gent Cruise Control (ICC) and Steering Assist, refer

to the dedicated ProPILOT Speed Limiter or Intel-

ligent Cruise Control (ICC) and Steering Assist

Speed Limiter section later in this manual.

Push the cruise control main “ON/OFF” switch

•

. The cruise control symbol

and the set

➃

➂

speed value

will turn off in the combination

➄

The speed limiter operation switches are located

on the steering wheel (right hand side).

The speed limiter allows you to set the desired ve-

hicle speed limit. While the speed limiter is activated,

you can perform normal braking and acceleration,

but the vehicle will not exceed the set speed.

meter display.

Push the speed limiter main “ON/OFF” switch

➁

•

The speed limiter operating condition is shown on

the top of Vehicle Information Display. For details,

see “Vehicle information display” in the “2. Instru-

ments and controls” section.

The cruise control system information in the

combination meter will be replaced with the

speed limiter information. For details see “Speed

limiter (where fitted)” later in this section.

When the vehicle reaches the set speed limit or if

the set speed limit is lower than the actual vehicle

speed, the accelerator pedal will not work (unless

fully depressed) until the vehicle speed drops below

the set speed limit.

SPEED LIMITER OPERATIONS

When the vehicle is stopped and the ignition is

turned to the off position.

•

Turning off the cruise control system will erase

the cruise control system memory.

When the actual vehicle speed exceeds the set

speed, an audible warning will be heard a short time

after the set speed is exceeded and driver interven-

tion is not detected.

When the speed limiter is on the cruise control sys-

tem cannot be operated.

WARNING

NIC4320

The speed limiter will not automatically brake

•

the vehicle to the set speed limit.

<CANCEL> switch

➀

Always observe posted speed limits. Do not

•

set the speed above them.

<RES +> (Resume) switch

<SET –> (Set) switch

Always confirm the setting status of the speed

limiter in the Vehicle Information Display.

•

Speed limiter main “ON/OFF” switch

➁

➂

When the speed limiter is set, avoid hard ac-

•

Cruise control main “ON/OFF” switch. (For

details, see “Cruise control (where fitted)”

earlier in this section)

celeration to reach the set limit to ensure that

the system can limit the speed of the vehicle

correctly.

234 Starting and driving

It is also possible to override the speed limiter by

fully depressing the accelerator pedal beyond the

resistance point.

Setting speed limit

Push the <SET> switch B .

The speed limit will be set at the current speed.

WARNING

When driving less than 30 km/h (20 MPH), the speed

limiter will be set to the minimum possible set speed

of 30 km/h (20 MPH).

The vehicle may accelerate when the speed

•

limiter cancels.

When the speed limit is set, the speed limiter sym-

When additional floor mats are used, be sure

•

bol

and the set speed value

will turn green.

➄

➃

that they are correctly secured and that they

cannot interfere with the accelerator pedal.

Mats not adapted to the vehicle may prevent

proper operation of the speed limiter.

Changing a speed limit

Use either of the following operations to change an

active speed limit:

NIC3816

Before setting speed

Fully depress the accelerator pedal beyond the re-

sistance point. The speed limiter will be suspended

to allow driving above the set speed. The set speed

Push and release the <RES> (Resume) switch

•

A or <SET> switch B . Each time you do this, the

set speed will increase or decrease by 1 km/h

(1 MPH).

value will flash and an audible warning will sound.

➄

The speed limiter will automatically resume when

the vehicle speed drops below the set speed limit.

Push and hold the <RES> (Resume) switch A or

<SET> switch B . The set speed will increase or

•

Resuming a previous set speed

decrease to the next multiple of 5 km/h (5 MPH)

and then in steps of 5 km/h (5 MPH).

If a set speed limit has been cancelled, the set speed

will be stored in the speed limiter memory and dis-

played in grey at the top of the vehicle information

display.

The new set speed limit value

the Vehicle Information Display.

will be displayed in

➄

NIC3817

After setting speed

Speed limiter symbol

When the actual vehicle speed exceeds the set

speed, an audible warning will be heard a short time

after the set speed is exceeded and driver interven-

tion is not detected.

This speed limit can be reactivated by pressing the

➃

➄

<RES> (Resume) switch A .

Set speed value

If the current vehicle speed is higher than the previ-

ous set speed, the accelerator pedal will not work

Turning the speed limiter on

The speed limiter can be switched on after engine

start or when driving.

Cancelling a speed limit

To cancel a set speed limit, push the <CANCEL>

and the set speed value

speed drops below the set speed limit.

will flash until the vehicle

➄

switch . The speed limiter symbol

and the set

➃

➀

Push the speed limiter main ON/OFF switch

➁

When the actual vehicle speed exceeds the set

speed, an audible warning will be heard a short time

after the set speed is exceeded and driver interven-

tion is not detected.

speed value

in the Vehicle Information Display

➄

The speed limiter symbol and the set speed value

➃

will turn grey.

will illuminate in the Vehicle Information Display.

➄

Starting and driving 235

INTELLIGENT CRUISE CONTROL (ICC) AND STEERING ASSIST

(where fitted) (on Manual Transmission vehicles)

The ICC and Steering Assist system is only an

aid to assist the driver and is not a collision

warning or avoidance device.

Turning the speed limiter off

The speed limiter system will be turned off when

one of the following operations is performed:

•

WARNING

Failure to follow the warnings and instructions for

proper use of the ICC and Steering Assist system

could result in serious injury or death.

The ICC and Steering Assist system is for use

on motorways with opposing traffic sepa-

rated by a barrier only, and is not intended for

city driving.

Push the speed limiter main ON/OFF switch

➁

•

The speed limiter symbol

and the set speed

➃

ICC and Steering Assist is not a self-driving

•

value

in the Vehicle Information Display will

➄

system. Within the limits of its capabilities, as

described in this manual, it helps the driver

with certain driving activities.

be turned off.

Always observe the posted speed limits and

do not set the speed over them.

•

Push the cruise control main ON/OFF switch

➂

The speed limiter information in the Vehicle In-

formation Display will be replaced with the cruise

control information. For details see “Cruise con-

trol (where fitted)” earlier in this section, “Intelli-

gent Cruise Control (ICC) and Steering Assist

(where fitted) (on ManualTransmission vehicles)”

later in this section, or “ProPILOT (where fitted)”

later in this section.

The ICC and Steering Assist system is not a re-

•

Never take your hands off the steering wheel

when driving. Always keep your hands on the

steering wheel and drive your vehicle safely.

placement for proper driving procedure and is

not designed to correct careless, inattentive

or absent-minded driving. ICC and Steering

Assist will not always steer the vehicle to keep

it in the lane. The ICC and Steering Assist sys-

tem is not designed to prevent loss of control.

It is the driver’s responsibility to stay alert,

drive safely, keep the vehicle in the travelling

lane, and be in control of the vehicle at all

times.

The ICC and Steering Assist system does not

react to stationary or slow moving vehicles.

•

Always drive carefully and attentively when

using the ICC and Steering Assist system. Read

and understand the Owner’s Manual thor-

oughly before using the ICC and Steering As-

sist system. To avoid serious injury or death,

do not rely on the system to prevent accidents

or to control the vehicle’s speed in emergency

situations. Do not use the ICC and Steering As-

sist system except in appropriate road and

traffic conditions.

When the vehicle is stopped and the ignition is

placed in the OFF position.

•

Turning off the speed limiter will erase the set

speed limit memory.

There are limitations to the ICC and Steering

•

Assist system capability. The ICC and Steering

Assist system does not function in all driving,

traffic, weather, and road conditions. It is the

driver’sresponsibilitytostayalert,drivesafely,

keep the vehicle in the travelling lane, and be

in control of the vehicle at all times.

Speed limiter malfunction

If the speed limiter malfunctions, the speed limiter

symbol

flash.

in the Vehicle Information Display will

➃

Turn the speed limiter off by pushing the speed lim-

iter main “ON/OFF” switch and have the system

➁

checked by a NISSAN dealer or qualified workshop.

236 Starting and driving

Starting and driving -> Cruise control system operations for Your Nissan Juke SUV 2020

Popular Manuals