Instruments and controls -> Headlight and turn signal switch for Your Nissan Qashqai SUV 2020

HEADLIGHT AND TURN SIGNAL SWITCH  
or  
position.  
The Intelligent Auto Headlight system can  
turn on the headlights automatically  
when it is dark and turn off the headlights  
when it is light.  
The headlights will also be turned on  
automatically at twilight or in rainy  
weather (when the windshield wiper is  
operated continuously).  
If the ignition switch is placed in the OFF  
position and one of the doors is opened  
and this condition is continued, the head-  
lights remain on for 5 minutes.  
JVI1624X  
JVI1616X  
HEADLIGHT SWITCH  
Lighting  
Intelligent Auto Headlight system  
The Intelligent Auto Headlight system  
allows the headlights to be set so they  
turn on and off automatically.  
Rotate the switch to the  
position, and  
the front parking, tail, license plate, and  
instrument panel lights will come on.  
To set the Intelligent Auto Headlight  
system:  
Rotate the switch to the  
position, and  
the headlights will come on and all the  
other lights remain on.  
1. Make sure the headlight switch is in  
the AUTO position  
.
2. Place the ignition switch in the ON  
position.  
3. The Intelligent Auto Headlight system  
automatically turns the headlights on  
and off.  
To turn the Intelligent Auto Headlight  
system off, turn the switch to the OFF,  
Instruments and controls 2-53  
For automatic headlights off delay  
setting, see “Vehicle Settings” (P.2-23).  
JVI0510X  
JVI1617X  
Be sure not to put anything on top of  
Headlight beam select  
the photo sensor  
located on the top  
To select the high beam function, push  
the lever forward. The high beam lights  
of the instrument panel. The photo  
sensor controls the Intelligent Auto  
Headlight; if it is covered, the photo  
sensor reacts as if it is dark and the  
headlights will illuminate.  
come on and the  
light illuminates.  
Pull the lever back to select the low beam.  
Pulling and releasing the lever flashes the  
headlight high beams on and off.  
Automatic headlights off delay:  
You can keep the headlights on for up to  
180 seconds after you place the ignition  
switch in the OFF and open any door then  
close all the doors. You can adjust the  
period of the automatic headlights off  
delay from 0 seconds (OFF) to 180 sec-  
onds. The factory default setting is 45  
seconds.  
2-54 Instruments and controls  
High beam assist  
the vicinity of the vehicle.  
.
The timing of switching the low  
beam and high beam may  
change under the following situa-  
tions.  
— The brightness of the head-  
lights of the oncoming vehicle  
or leading vehicle.  
— The movement and direction  
of the oncoming vehicle and  
the leading vehicle.  
The high beam assist system will operate  
when the vehicle is driven at speeds of  
approximately 19 MPH (30 km/h) and  
above. If an oncoming vehicle or leading  
vehicle appears in front of your vehicle  
when the headlight high beam is on, the  
headlight will be switched to the low  
beam automatically.  
— When the headlights of the  
oncoming vehicle or the lead-  
ing vehicle are turned off,  
when the color of the light is  
affected due to foreign mate-  
rials on the lights, or when the  
light beam is out of position.  
— When there is a sudden, con-  
tinuous change in brightness.  
Precautions on high beam assist:  
— When only one light on the  
oncoming vehicle or the lead-  
ing vehicle is illuminated.  
— When the oncoming vehicle or  
the leading vehicle is a two-  
wheeled vehicle.  
Road conditions (incline,  
curve, the road surface, etc.).  
— The number of passengers  
and the amount of cargo.  
— When driving on a road that  
passes over rolling hills, or a  
road that has level differ-  
ences.  
— When driving on a road with  
many curves.  
— When a sign or mirror-like  
surface is reflecting intense  
light towards the front of the  
vehicle.  
WARNING  
.
.
The high beam assist system is a  
convenience but it is not a sub-  
stitute for safe driving operation.  
The driver should remain alert at  
all times, ensure safe driving  
practices and switch the high  
beams and low beam manually  
when necessary.  
— When the container, etc. being  
towed by a leading vehicle is  
reflecting intense light.  
The high beam or low beam may  
not switch automatically under  
the following conditions. Switch  
the high beam and low beam  
manually.  
— When  
a headlight on your  
vehicle is damaged or dirty.  
— During bad weather (rain, fog,  
— When the vehicle is leaning at  
an angle due to a punctured  
tire, being towed, etc.  
snow, wind, etc.).  
— When a light source similar to  
a headlight or tail light is in  
Instruments and controls 2-55  
headlight remains the low beam.  
To turn off the high beam assist system,  
turn the headlight switch to the  
position or select the low beam position  
by placing the lever in the neutral posi-  
tion.  
JVI1621X  
WAC0198X  
High beam assist operations:  
Ambient image sensor maintenance:  
To activate the high beam assist system,  
The ambient image sensor for the high  
beam assist system is located in front of  
the inside mirror. To keep the proper  
operation of the high beam assist system  
and prevent a system malfunction, be  
sure to observe the following:  
turn the headlight switch to the AUTO  
position  
and push the lever forward  
(high beam position). The high beam  
assist indicator light in the meter will  
illuminate while the headlights are turned  
on.  
.
.
Always keep the windshield clean.  
If the high beam assist indicator light  
does not illuminate in the above condi-  
tion, it may indicate that the system is not  
functioning properly. It is recommended  
Do not attach a sticker (including  
transparent material) or install an  
accessory near the ambient image  
sensor.  
you have the system checked by  
a
.
Do not strike or damage the areas  
around the ambient image sensor. Do  
not touch the sensor lens that is  
located on the ambient image sensor.  
NISSAN dealer.  
When the vehicle speed lowers to less  
than approximately 13 MPH (20 km/h), the  
2-56 Instruments and controls  
If the ambient image sensor is damaged  
due to an accident, it is recommended  
you contact a NISSAN dealer.  
if the headlights turn off auto-  
matically.  
WARNING  
When the LED DRL system is active,  
tail lights on your vehicle are not on.  
It is necessary at dusk to turn on  
your headlights. Failure to do so  
could cause an accident injuring  
yourself and others.  
Battery saver system  
Daytime Running Light (DRL) sys-  
tem  
.
When the headlight switch is in the  
or  
position while the ignition  
The LED portion of the headlights auto-  
matically illuminate at 100% intensity  
when the engine is started and the  
parking brake released. The LED Daytime  
Running Light (DRL) operate with the  
headlight switch in the OFF position or  
switch is in the ON position, the lights  
will automatically turn off within a  
period of time after the ignition switch  
has been placed in the OFF position.  
.
When the headlight switch remains in  
the  
or  
position after the lights  
in the  
position. When you turn the  
automatically turn off, the lights will  
turn on when the ignition switch is  
placed in the ON position.  
headlight switch to the  
position for  
full illumination, the LED lights switch  
from LED DRL to the park function.  
If the parking brake is applied before the  
engine is started, the LED DRL do not  
illuminate. The LED DRL illuminate when  
the parking brake is released. The LED  
DRL will remain on until the ignition  
switch is placed in the OFF position.  
It is necessary at dusk to turn the head-  
light switch ON for interior controls and  
switches to illuminate, as those remain  
OFF while the switch is in the OFF  
position.  
CAUTION  
.
.
When you turn on the headlight  
switch again after the lights auto-  
matically turn off, the lights will  
not turn off automatically. Be  
sure to turn the light switch to  
the OFF position when you leave  
the vehicle for extended periods  
of time, otherwise the battery will  
be discharged.  
Never leave the light switch on  
when the engine is not running  
for extended periods of time even  
Instruments and controls 2-57  
signal will automatically flash three times.  
Choose the appropriate method to signal  
a lane change based on road and traffic  
conditions.  
JVI1591X  
JVI0980X  
TURN SIGNAL SWITCH  
Turn signal  
Move the lever up or down to signal the  
turning direction. When the turn is com-  
pleted, the turn signals cancel automati-  
cally.  
FOG LIGHT SWITCH (if so equipped)  
To turn the fog lights on, turn the head-  
light switch to the  
position, then turn  
the fog light switch to the  
position.  
To turn the fog lights on with the head-  
light switch in the AUTO position, the  
headlights must be on, then turn the fog  
light switch to the  
position.  
Lane change signal  
To turn them off, turn the fog light switch  
Move the lever up or down until the turn  
signal begins to flash, but the lever does  
not latch, to signal a lane change. Hold  
the lever until the lane change is com-  
pleted.  
to the OFF position.  
The headlights must be on for the fog  
lights to operate. The fog lights automa-  
tically turn off when the high beam  
headlights are selected.  
Move the lever up or down until the turn  
signal begins to flash, but the lever does  
not latch, and release the lever. The turn  
2-58 Instruments and controls