Get Safety Seats seat belts and supplemental restraint system -> Child restraints Guide for Nissan Qashqai SUV 2020

CHILD RESTRAINTS

seriously injured or killed in a sudden

stop or collision.

SSS0099

JVR0473X

If you answered no to any of these

questions, the child should remain in a

booster seat using a three-point type

seat belt.

NOTE:

Laws in some communities may follow

different guidelines. Check local and

state regulations to confirm your child

is using the correct restraint system

before traveling.

WARNING

Never let a child stand or kneel on

any seat and do not allow a child in

the cargo area. The child could be

SSS0100

Safety — Seats, seat belts and supplemental restraint system 1-21

PRECAUTIONS ON CHILD RE-

STRAINTS

seat than in the front seat. If

you must install a forward-

facing child restraint in the

front seat, see “Forward-fa-

cing child restraint installation

using the seat belts” (P.1-34).

will not be properly installed

using the damaged ancho-

rage, and a child could be

seriously injured or killed in a

collision.

WARNING

— Never use the anchor points

for adult seat belts or har-

nesses.

— A child restraint with a top

tether strap should not be

used in the front passenger

seat.

— Keep seatbacks as upright as

possible after fitting the child

restraint.

— Infants and children should

always be placed in an appro-

priate child restraint while in

the vehicle.

.

Failure to follow the warnings

and instructions for proper use

and installation of child restraints

could result in serious injury or

death of a child or other passen-

gers in a sudden stop or collision:

— Even with the NISSAN Ad-

vanced Air Bag System, never

install a rear-facing child re-

straint in the front seat. An

inflating air bag could ser-

iously injure or kill a child. A

rear-facing child restraint

must only be used in the rear

seat.

— Be sure to purchase a child

restraint that will fit the child

and vehicle. Some child re-

straints may not fit properly

in your vehicle.

— Child restraint anchorages are

designed to withstand only

those loads imposed by cor-

rectly fitted child restraints.

Under no circumstances are

they to be used to attach

adult seat belts, or other

items or equipment to the

vehicle. Doing so could da-

mage the child restraint an-

chorages. The child restraint

— The child restraint must be

used and installed properly.

Always follow all of the child

restraint manufacturer’s in-

structions for installation and

use.

— Infants and children should

never be held on anyone’s

lap. Even the strongest adult

cannot resist the forces of a

collision.

— Do not put a seat belt around

both a child and another pas-

senger.

— NISSAN recommends that all

child restraints be installed in

the rear seat. Studies show

that children are safer when

properly restrained in the rear

.

When the child restraint is not in

use, keep it secured with the

LATCH system or a seat belt. In a

sudden stop or collision, loose

objects can injure occupants or

damage the vehicle.

1-22 Safety — Seats, seat belts and supplemental restraint system

.

Check the child restraint in your

vehicle to be sure it is compatible with

the vehicle’s seat and seat belt sys-

tem.

If the child restraint is compatible with

your vehicle, place your child in the

child restraint and check the various

adjustments to be sure the child

restraint is compatible with your child.

Choose a child restraint that is de-

signed for your child’s height and

weight. Always follow all recom-

mended procedures.

If the combined weight of the child

and child restraint is less than 65 lbs

(29.5 kg), you may use either the

LATCH anchors or the seat belt to

install the child restraint (not both at

the same time).

If the combined weight of the child

and child restraint is greater than 65

lbs (29.5 kg), use the vehicle’s seat belt

(not the lower anchors) to install the

child restraint.

law requires the top tether strap on

forward-facing child restraints be se-

cured to the designated anchor point

on the vehicle.

CAUTION

A child restraint in a closed vehicle

can become very hot. Check the

seating surface and buckles before

placing a child in the child restraint.

This vehicle is equipped with a universal

child restraint anchor system, referred to

as the LATCH (Lower Anchors and

Tethers for CHildren) system. Some child

restraints include rigid or webbing-

mounted attachments that can be con-

nected to these anchors.

For details, see “Lower Anchors and

Tethers for CHildren (LATCH) system”

(P.1-24).

If you do not have a LATCH compatible

child restraint, the vehicle seat belts can

be used.

Several manufacturers offer child re-

straints for infants and small children of

various sizes. When selecting any child

restraint, keep the following points in

mind:

.

Be sure to follow the child restraint

manufacturer’s instructions for instal-

lation.

All U.S. states and Canadian provinces

or territories require that infants and

small children be restrained in an ap-

proved child restraint at all times while

the vehicle is being operated. Canadian

.

Choose only a restraint with a label

certifying that it complies with Federal

Motor Vehicle Safety Standard 213 or

Canadian Motor Vehicle Safety Stan-

dard 213.

Safety — Seats, seat belts and supplemental restraint system 1-23

restraint manufacturer’s instructions for

installation.

.

Inspect the lower anchors by in-

serting your fingers into the low-

er anchor area. Feel to make sure

there are no obstructions over

the anchors such as seat belt

webbing or seat cushion material.

The child restraint will not be

secured properly if the lower

anchors are obstructed.

Child restraint anchorages are

designed to withstand only those

loads imposed by correctly fitted

child restraints. Under no circum-

stances are they to be used to

attach adult seat belts, or other

items or equipment to the vehi-

cle. Doing so could damage the

child restraint anchorages. The

child restraint will not be properly

installed using the damaged an-

chorage, and a child could be

seriously injured or killed in a

collision.

CAUTION

Store the loose LATCH covers (for

example, in the console box) where

they will not get damaged to avoid

losing them. (See “Console box” (P.2-

69).)

LATCH lower anchor

JVR0555X

LATCH system anchor location

WARNING

Lower Anchors and Tethers for

CHildren (LATCH) SYSTEM

Failure to follow the warnings and

instructions for proper use and in-

stallation of child restraints could

result in serious injury or death of a

child or other passengers in a sud-

den stop or collision:

Your vehicle is equipped with special

anchor points that are used with LATCH

system compatible child restraints. This

system may also be referred to as the

ISOFIX or ISOFIX compatible system. With

this system, you do not have to use a

vehicle seat belt to secure the child

restraint unless the combined weight of

the child and child restraint exceeds 65

lbs (29.5 kg). If the combined weight of the

child and child restraint is greater than 65

lbs (29.5 kg), use the vehicle’s seat belt

(not the lower anchors) to install the child

restraint. Be sure to follow the child

.

Attach LATCH system compatible

child restraints only at the loca-

tions shown in the illustration.

Do not secure a child restraint in

the center rear seating position

using the LATCH lower anchors.

The child restraint will not be

secured properly.

LATCH lower anchor location

The LATCH lower anchor points are

provided to install child restraints in the

rear outboard seating positions only. Do

not attempt to install a child restraint in

the center seating position using the

LATCH lower anchors.

.

1-24 Safety — Seats, seat belts and supplemental restraint system

SSS0643

LATCH webbing-mounted attachment

SSS0644

LATCH rigid attachment

When installing a child restraint, carefully

read and follow the instructions in this

manual and those supplied with the child

restraint.

Installing child restraint LATCH

lower anchor attachments

LATCH compatible child restraints include

two rigid or webbing-mounted attach-

ments that can be connected to two

anchors located at certain seating posi-

tions in your vehicle. With this system, you

do not have to use a vehicle seat belt to

secure the child restraint. Check your

child restraint for a label stating that it is

compatible with LATCH. This information

may also be in the instructions provided

by the child restraint manufacturer.

Top tether anchor

JVR0556X

LATCH lower anchor cover removal

WARNING

The LATCH lower anchor points are

located under covers labelled ISOFIX at

the bottom of the rear outboard seat

cushions. To access a LATCH lower an-

chor point, insert your finger into the

cover and pull the cover off.

Properly secure cargo and do not

allow it to contact the top tether

strap when it is attached to the top

tether anchor. Cargo that is not

properly secured or cargo that con-

tacts the top tether strap may da-

mage the top tether strap during a

Safety — Seats, seat belts and supplemental restraint system 1-25

collision. If the parcel shelf contacts

the top tether strap when it is at-

tached to the top tether anchor,

remove the parcel shelf from the

vehicle or secure it on the cargo floor

below its attachment location. If the

parcel shelf is not removed, it may

damage the top tether strap during a

collision. Your child could be ser-

iously injured or killed in a collision

if the child restraint top tether strap

is damaged.

collision.

Anchor points are located on the back

side of the seatbacks.

If a child restraint has a top tether strap, it

must be used when installing with the

LATCH lower anchor attachments or seat

belts.

If you have any questions when instal-

ling a top tether strap child restraint on

the rear seat, it is recommended you

visit a NISSAN dealer for this service.

REAR-FACING CHILD RESTRAINT

INSTALLATION USING LATCH

WAB0058X

Refer to all Warnings and Cautions in the

“Child safety” and “Child restraints” sec-

tions before installing a child restraint.

Top tether anchor point locations

WARNING

Do not use the lower anchors if the

combined weight of the child and the

child restraint exceeds 65 lbs (29.5 kg). If

the combined weight of the child and the

child restraint is greater than 65 lbs (29.5

kg), use the vehicle’s seat belt (not the

lower anchors) to install the child re-

straint. Be sure to follow the child re-

straint manufacturer’s instructions for

installation.

Child restraint anchorages are de-

signed to withstand only those loads

imposed by correctly fitted child

restraints. Under no circumstances

are they to be used to attach adult

seat belts, or other items or equip-

ment to the vehicle. Doing so could

damage the child restraint an-

chorages. The child restraint will not

be properly installed using the da-

maged anchorage, and a child could

be seriously injured or killed in a

1-26 Safety — Seats, seat belts and supplemental restraint system

Follow these steps to install a rear-facing

child restraint using the LATCH system:

1. Position the child restraint on the seat.

Always follow the child restraint man-

ufacturer’s instructions.

SSS0648

SSS0649

Rear-facing web-mounted — step 2

Rear-facing rigid-mounted — step 2

2. Secure the child restraint anchor at-

tachments to the LATCH lower an-

chors. Check to make sure the LATCH

attachment is properly attached to

the lower anchors.

Safety — Seats, seat belts and supplemental restraint system 1-27

in all types of vehicles.

5. Check to make sure the child restraint

is properly secured prior to each use. If

the child restraint is loose, repeat

steps 1 through 4.

REAR-FACING CHILD RESTRAINT

INSTALLATION USING THE SEAT

BELTS

WARNING

The three-point seat belt with Auto-

matic Locking Retractor (ALR) must

be used when installing a child re-

straint. Failure to use the ALR mode

will result in the child restraint not

being properly secured. The restraint

could tip over or be loose and cause

injury to a child in a sudden stop or

collision.

SSS0639

SSS0650

Rear-facing — step 3

Rear-facing — step 4

3. For child restraints that are equipped

with webbing-mounted attachments,

remove any additional slack from the

anchor attachments. Press downward

and rearward firmly in the center of

the child restraint with your hand to

compress the vehicle seat cushion

and seatback while tightening the

webbing of the anchor attachments.

4. After attaching the child restraint, test

it before you place the child in it. Push

it from side to side while holding the

child restraint near the LATCH attach-

ment path. The child restraint should

not move more than 1 inch (25 mm),

from side to side. Try to tug it forward

and check to see if the LATCH attach-

ment holds the restraint in place. If the

restraint is not secure, tighten the

LATCH attachment as necessary, or

put the restraint in another seat and

test it again. You may need to try a

different child restraint or try installing

by using the vehicle seat belt (if

applicable). Not all child restraints fit

1-28 Safety — Seats, seat belts and supplemental restraint system

1. Child restraints for infants must be

used in the rear-facing direction and

therefore must not be used in the

front seat. Position the child restraint

on the seat. Always follow the re-

straint manufacturer’s instructions.

SSS0100

SSS0654

Rear-facing — step 1

Rear-facing — step 2

Refer to all Warnings and Cautions in the

“Child safety” (P.1-19) and “Child restraints”

(P.1-21) before installing a child restraint.

2. Route the seat belt tongue through

the child restraint and insert it into the

buckle until you hear and feel the

latch engage. Be sure to follow the

child restraint manufacturer’s instruc-

tions for belt routing.

Do not use the lower anchors if the

combined weight of the child and the

child restraint exceeds 65 lbs (29.5 kg). If

the combined weight of the child and the

child restraint is greater than 65 lbs (29.5

kg), use the vehicle’s seat belt (not the

lower anchors) to install the child re-

straint. Be sure to follow the child re-

straint manufacturer’s instructions for

installation.

Follow these steps to install a rear-facing

child restraint using the vehicle seat belts

in the rear seats:

Safety — Seats, seat belts and supplemental restraint system 1-29

SSS0655

SSS0656

SSS0657

Rear-facing — step 3

Rear-facing — step 4

Rear-facing — step 5

3. Pull the shoulder belt until the belt is

fully extended. At this time, the seat

belt retractor is in the Automatic

Locking Retractor (ALR) mode (child

restraint mode). It reverts to the

Emergency Locking Retractor (ELR)

mode when the seat belt is fully

retracted.

4. Allow the seat belt to retract. Pull up

on the shoulder belt to remove any

slack in the belt.

5. Remove any additional slack from the

seat belt; press downward and rear-

ward firmly in the center of the child

restraint to compress the vehicle seat

cushion and seatback while pulling up

on the seat belt.

1-30 Safety — Seats, seat belts and supplemental restraint system

each use. If the seat belt is not locked,

repeat steps 1 through 6.

After the child restraint is removed and

the seat belt fully retracted, the ALR mode

(child restraint mode) is canceled.

FORWARD-FACING CHILD RE-

STRAINT INSTALLATION USING

LATCH

Refer to all Warnings and Cautions in the

“Child safety” and “Child restraints” sec-

tions before installing a child restraint.

Do not use the lower anchors if the

combined weight of the child and the

child restraint exceeds 65 lbs (29.5 kg). If

the combined weight of the child and the

child restraint is greater than 65 lbs (29.5

kg), use the vehicle’s seat belt (not the

lower anchors) to install the child re-

straint. Be sure to follow the child re-

straint manufacturer’s instructions for

installation.

Follow these steps to install a forward-

facing child restraint using the LATCH

system:

1. Position the child restraint on the seat.

Always follow the child restraint man-

ufacturer’s instructions.

SSS0658

SSS0645

Forward-facing web-mounted — step 2

Rear-facing — step 6

6. After attaching the child restraint, test

it before you place the child in it. Push

it from side to side while holding the

child restraint near the seat belt path.

The child restraint should not move

more than 1 inch (25 mm), from side to

side. Try to tug it forward and check to

see if the belt holds the restraint in

place. If the restraint is not secure,

tighten the seat belt as necessary, or

put the restraint in another seat and

test it again. You may need to try a

different child restraint. Not all child

restraints fit in all types of vehicles.

2. Secure the child restraint anchor at-

tachments to the LATCH lower an-

chors. Check to make sure the LATCH

attachment is properly attached to

the lower anchors.

If the child restraint is equipped with a

top tether strap, route the top tether

strap and secure the tether strap to

the tether anchor point. See “Installing

top tether strap” (P.1-33). Do not install

child restraints that require the use of

a top tether strap in seating positions

that do not have a top tether anchor.

7. Check to make sure that the child

restraint is properly secured prior to

Safety — Seats, seat belts and supplemental restraint system 1-31

child restraint.

SSS0646

Forward-facing rigid-mounted — step 2

SSS0647

Forward-facing — step 4

3. The back of the child restraint should

be secured against the vehicle seat-

back.

4. For child restraints that are equipped

with webbing-mounted attachments,

remove any additional slack from the

anchor attachments. Press downward

and rearward firmly in the center of

the child restraint with your knee to

compress the vehicle seat cushion

and seatback while tightening the

webbing of the anchor attachments.

If necessary, adjust or remove the

head restraint to obtain the correct

child restraint fit. If the head restraint

is removed, store it in a secure place.

Be sure to reinstall the head re-

straint when the child restraint is

removed. See “Head restraints/head-

rests” (P.1-8) for head restraint adjust-

ment information.

5. Tighten the tether strap according to

the manufacturer’s instructions to

remove any slack.

If the seating position does not have a

head restraint and it is interfering with

the proper child restraint fit, try an-

other seating position or a different

1-32 Safety — Seats, seat belts and supplemental restraint system

7. Check to make sure the child restraint

is properly secured prior to each use. If

the child restraint is loose, repeat

steps 1 through 6.

SSS0638

WAB0058X

Forward-facing — step 6

Installing top tether strap

6. After attaching the child restraint, test

it before you place the child in it. Push

it from side to side while holding the

child restraint near the LATCH attach-

ment path. The child restraint should

not move more than 1 inch (25 mm),

from side to side. Try to tug it forward

and check to see if the LATCH attach-

ment holds the restraint in place. If the

restraint is not secure, tighten the

LATCH attachment as necessary, or

put the restraint in another seat and

test it again. You may need to try a

different child restraint. Not all child

restraints fit in all types of vehicles.

WARNING

Child restraint anchorages are de-

signed to withstand only those loads

imposed by correctly fitted child

restraints. Under no circumstances

are they to be used to attach adult

seat belts, or other items or equip-

ment to the vehicle. Doing so could

damage the child restraint an-

chorages. The child restraint will not

be properly installed using the da-

maged anchorage, and a child could

be seriously injured or killed in a

Safety — Seats, seat belts and supplemental restraint system 1-33

FORWARD-FACING CHILD RE-

STRAINT INSTALLATION USING THE

SEAT BELTS

collision.

The child restraint top tether strap must

be used when installing the child restraint

with the LATCH lower anchor attach-

ments.

WARNING

First, secure the child restraint with the

LATCH lower anchors (rear outboard

seating positions only).

1. Remove the head restraint and store it

in a secure place. Be sure to reinstall

the head restraint when the child

restraint is removed.

The three-point seat belt with Auto-

matic Locking Retractor (ALR) must

be used when installing a child re-

straint. Failure to use the ALR mode

will result in the child restraint not

being properly secured. The restraint

could tip over or be loose and cause

injury to a child in a sudden stop or

collision. Also, it can change the

operation of the front passenger air

bag. See “Front passenger air bag

and status light” (P.1-50).

SSS0640

See “Head restraints/headrests” (P.1-8)

for head restraint adjustment, re-

moval and installation information.

Forward-facing (front passenger seat) — step 1

Refer to all Warnings and Cautions in the

“Child safety” and “Child restraints” sec-

tions before installing a child restraint.

2. Position the top tether strap as

shown.

Do not use the lower anchors if the

combined weight of the child and the

child restraint exceeds 65 lbs (29.5 kg). If

the combined weight of the child and the

child restraint is greater than 65 lbs (29.5

kg), use the vehicle’s seat belt (not the

lower anchors) to install the child re-

straint. Be sure to follow the child re-

straint manufacturer’s instructions for

installation.

3. Secure the top tether strap to the

tether anchor point as shown.

4. Refer to the appropriate child restraint

installation procedure steps in this

section before tightening the tether

strap.

If you have any questions when instal-

ling a top tether strap, it is recom-

mended that you visit a NISSAN dealer

for this service.

Follow these steps to install a forward-

facing child restraint using the vehicle

seat belt in the rear seats or in the front

1-34 Safety — Seats, seat belts and supplemental restraint system

passenger seat:

1. If you must install a child restraint in

the front seat, it should be placed in

a

forward-facing direction only.

Move the seat to the rearmost posi-

tion. Child restraints for infants must

be used in the rear-facing direction

and, therefore, must not be used in

the front seat.

2. Position the child restraint on the seat.

Always follow the child restraint man-

ufacturer’s instructions.

The back of the child restraint should

be secured against the vehicle seat-

back.

SSS0360B

SSS0651

Forward-facing — step 3

Forward-facing — step 4

If necessary, adjust or remove the

head restraint to obtain the correct

child restraint fit. If the head restraint

is removed, store it in a secure place.

Be sure to reinstall the head re-

straint when the child restraint is

removed. See “Head restraints/head-

rests” (P.1-8) for head restraint adjust-

ment, removal and installation

information.

If the seating position does not have

an adjustable head restraint and it is

interfering with the proper child re-

straint fit, try another seating position

or a different child restraint.

3. Route the seat belt tongue through

the child restraint and insert it into the

buckle until you hear and feel the

latch engage. Be sure to follow the

child restraint manufacturer’s instruc-

tions for belt routing.

4. Pull the shoulder belt until the belt is

fully extended. At this time, the seat

belt retractor is in the Automatic

Locking Retractor (ALR) mode (child

restraint mode). It reverts to Emer-

gency Locking Retractor (ELR) mode

when the seat belt is fully retracted.

If the child restraint is equipped with a

top tether strap, route the top tether

strap and secure the tether strap to

the tether anchor point (rear seat

installation only). See “Installing top

tether strap” (P.1-37). Do not install

child restraints that require the use

of a top tether strap in seating posi-

tions that do not have a top tether

anchor.

Safety — Seats, seat belts and supplemental restraint system 1-35

SSS0652

SSS0653

SSS0641

Forward-facing — step 5

Forward-facing — step 6

Forward-facing — step 8

5. Allow the seat belt to retract. Pull up

on the shoulder belt to remove any

slack in the belt.

6. Remove any additional slack from the

seat belt; press downward and rear-

ward firmly in the center of the child

restraint with your knee to compress

the vehicle seat cushion and seatback

while pulling up on the seat belt.

7. Tighten the tether strap according to

the manufacturer’s instructions to

remove any slack.

8. After attaching the child restraint, test

it before you place the child in it. Push

it from side to side while holding the

child restraint near the seat belt path.

The child restraint should not move

more than 1 inch (25 mm), from side to

side. Try to tug it forward and check to

see if the belt holds the restraint in

place. If the restraint is not secure,

tighten the seat belt as necessary, or

put the restraint in another seat and

test it again. You may need to try a

different child restraint. Not all child

restraints fit in all types of vehicles.

9. Check to make sure the child restraint

is properly secured prior to each use. If

1-36 Safety — Seats, seat belts and supplemental restraint system

the seat belt is not locked, repeat

steps 2 through 8.

SSS0676

WAB0058X

Forward-facing — step 10

Installing top tether strap

10. If the child restraint is installed in the

front passenger seat, place the igni-

tion switch in the ON position. The

front passenger air bag status light

should illuminate. If this light is not

illuminated, see “Front passenger air

bag and status light” (P.1-50). Move

the child restraint to another seating

position. Have the system checked. It

is recommended you visit a NISSAN

dealer for this service.

WARNING

Child restraint anchorages are de-

signed to withstand only those loads

imposed by correctly fitted child

restraints. Under no circumstances

are they to be used to attach adult

seat belts, or other items or equip-

ment to the vehicle. Doing so could

damage the child restraint an-

chorages. The child restraint will not

be properly installed using the da-

maged anchorage, and a child could

be seriously injured or killed in a

After the child restraint is removed and

the seat belt is fully retracted, the ALR

mode (child restraint mode) is canceled.

Safety — Seats, seat belts and supplemental restraint system 1-37

.

Check the booster seat in your vehicle

to be sure it is compatible with the

vehicle’s seat and seat belt system.

BOOSTER SEATS

Precautions on booster seats

collision.

The child restraint top tether strap must

be used when installing the child restraint

with the seat belts.

WARNING

First, secure the child restraint with the

If a booster seat and seat belt are not

used properly, the risk of a child

being injured or killed in a sudden

stop or collision greatly increases:

seat belt.

1. Remove the head restraint and store it

in a secure place. Be sure to reinstall

the head restraint when the child

restraint is removed.

.

Make sure the shoulder portion of

the belt is away from the child’s

face and neck and the lap portion

of the belt does not cross the

stomach.

See “Head restraints/headrests” (P.1-8)

for head restraint adjustment, re-

moval and installation information.

2. Position the top tether strap as

.

Make sure the shoulder belt is not

behind the child or under the

child’s arm.

shown.

3. Secure the top tether strap to the

tether anchor point as shown.

4. Refer to the appropriate child restraint

installation procedure steps in this

section before tightening the tether

strap.

If you have any questions when instal-

ling a top tether strap, it is recom-

mended you visit a NISSAN dealer for

this service.

A

booster seat must only be

installed in a seating position that

has a lap/shoulder belt.

Booster seats of various sizes are offered

by several manufacturers. When selecting

any booster seat, keep the following

points in mind:

.

Choose only a booster seat with a

label certifying that it complies with

Federal Motor Vehicle Safety Standard

213 or Canadian Motor Vehicle Safety

Standard 213.

1-38 Safety — Seats, seat belts and supplemental restraint system

.

Make sure the child’s head will be

properly supported by the booster

seat or vehicle seat. The seatback

must be at or above the center of

the child’s ears. For example, if a low

back booster seat

is chosen, the

vehicle seatback must be at or above

the center of the child’s ears. If the

seatback is lower than the center of

the child’s ears, a high back booster

seat

should be used.

.

If the booster seat is compatible with

your vehicle, place your child in the

booster seat and check the various

adjustments to be sure the booster

seat is compatible with your child.

Always follow all recommended pro-

cedures.

LRS0453

LRS0464

All U.S. states and Canadian provinces

or territories require that infants and

small children be restrained in an ap-

proved child restraint at all times while

the vehicle is being operated.

The instructions in this section apply to

booster seat installation in the rear seats

or the front passenger seat.

Booster seat installation

WARNING

To avoid injury to child, do not use

the lap/shoulder belt Automatic

Locking Retractor (ALR) mode when

LRS0455

Safety — Seats, seat belts and supplemental restraint system 1-39

using a booster seat with the seat

belts.

Refer to all Warnings and Cautions in the

“Child safety”, “Child restraints” and “Boos-

ter seats” sections earlier in this section

before installing a child restraint.

Follow these steps to install a booster

seat in the rear seat or in the front

passenger seat:

SSS0640

LRS0454

Front passenger position

1. If you must install a booster seat in

the front seat, move the seat to the

rearmost position.

3. The booster seat should be positioned

on the vehicle seat so that it is stable.

If necessary, adjust or remove the

head restraint to obtain the correct

booster seat fit. If the head restraint is

removed, store it in a secure place. Be

sure to reinstall the head restraint

when the booster seat is removed.

See “Head restraints/headrests” (P.1-8)

for head restraint adjustment, re-

moval and installation information.

2. Position the booster seat on the seat.

Only place it in

a forward-facing

direction. Always follow the booster

seat manufacturer’s instructions.

If the seating position does not have a

head restraint and it is interfering with

the proper booster seat fit, try another

seating position or a different booster

seat.

1-40 Safety — Seats, seat belts and supplemental restraint system

4. Position the lap portion of the seat

belt low and snug on the child’s hips.

Be sure to follow the booster seat

manufacturer’s instructions for ad-

justing the seat belt routing.

5. Pull the shoulder belt portion of the

seat belt toward the retractor to take

up extra slack. Be sure the shoulder

belt is positioned across the top,

middle portion of the child’s shoulder.

Be sure to follow the booster seat

manufacturer’s instructions for ad-

justing the seat belt routing.

6. Follow the warnings, cautions and

instructions for properly fastening a

seat belt shown in “Seat belts” (P.1-12).

SSS0676

7. If the booster seat is installed in the

front passenger seat, place the igni-

tion switch in the ON position. The

front passenger air bag status light

may or may not illuminate de-

pending on the size of the child and

the type of booster seat used. See

“Front passenger air bag and status

light” (P.1-50).

Safety — Seats, seat belts and supplemental restraint system 1-41

Safety Seats seat belts and supplemental restraint system -> Child restraints for Your Nissan Qashqai SUV 2020

Popular Manuals