Get Maintenance and do-it-yourself -> Fuses Guide for Nissan X Trail SUV 2020

FUSES

ENGINE COMPARTMENT

SDI1753

JVM0444X

Type A

QR25DE engine model (Example)

JVM0386X

The holder

also contains the fuses. For

QR25DE engine model (Example)

checking and/or replacing, see a NISSAN dealer.

Fusible links

CAUTION:

Never use fuse of

If any electrical equipment does not operate

and the fuses are in good condition, check the

fusible links. If any of these fusible links are

melted, replace only with genuine NISSAN

parts.

higher or lower

amperage rating than that specified on the

fuse box cover. This could damage the

electrical system or cause a fire.

If any electrical equipment does not operate,

check for an open fuse.

PASSENGER COMPARTMENT

SDI1754

1. Be sure the ignition switch is in the “OFF”

CAUTION:

Type B

position.

7. Remove the fuse using the fuse puller

Never use

a fuse of a higher or lower

2. Be sure the headlight switch is in the “OFF”

position.

3. Open the engine hood.

located in the passenger compartment.

amperage rating than that specified on the

fuse box cover. This could damage the

electrical system or cause a fire.

8. If the fuse is open , replace it with a new

fuse

4. Remove the air cleaner duct. (See “Engine

If the new fuse also opens, after installing, have

the electrical system checked, and if necessary

repaired, by a NISSAN dealer.

If any electrical equipment does not operate,

check for an open fuse.

compartment check locations” (P.8-6).)

5. Remove the fuse/fusible link box cover by

using a suitable tool and pushing the tab.

6. Locate the fuse that needs to be replaced.

Maintenance and do-it-yourself 8-33

6. If the fuse is open , replace it with a new

fuse

Outer side of the instrument panel

If the new fuse also opens, after installing, have

the electrical system checked, and if necessary

repaired, by a NISSAN dealer.

JVM0783X

JVM0784X

SDI1754

For all LHD model

For Stop/Start System or Idling Stop System (if equipped)

1. Be sure the ignition switch is in the “OFF”

position.

2. Be sure the headlight switch is in the “OFF”

position.

3. Remove the fuse box cover.

4. Locate the fuse that needs to be replaced.

5. Remove the fuse using the fuse puller

8-34 Maintenance and do-it-yourself

Glove box

Extended storage fuse switch

JVM0415X

JVM0786X

Example

For all RHD model

1. Be sure the ignition switch is in the “OFF”

To reduce battery drain, the extended storage

fuse switch comes from the factory switched

off. Prior to delivery of your vehicle, the switch is

pushed in (switched on) and should always

remain on.

position.

2. Be sure the headlight switch is in the “OFF”

position.

3. Open the glove box and unlock the damper

If the extended storage fuse switch is not

pushed in (switched on), the “Shipping Mode

On Push Storage Fuse” warning may appear in

the vehicle information display. See “Vehicle

information display warnings and indicators”

(P.2-31).

If any electrical equipment does not operate,

remove the extended storage fuse switch and

push it in again.

4. Hold the glove box lid so that the distance

between the upper end of the lid and the

dashboard is about 5 cm (2 in), and then

pull off the hinges

side of the lid.

located on the under-

SDI1754

5. Unlock the left and right stoppers

and

8. If the fuse is open

fuse

, replace it with a new

remove the glove box lid.

6. Locate the fuse that needs to be replaced.

7. Remove the fuse using the fuse puller.

NOTE:

If the new fuse also opens, after installing, have

the electrical system checked, and if necessary

repaired, by a NISSAN dealer.

If the extended storage fuse switch malfunc-

tions, see a NISSAN dealer.

How to remove the extended storage fuse

switch:

1. To remove the extended storage fuse

switch, be sure the ignition switch is in the

“OFF” or “LOCK” position.

Maintenance and do-it-yourself 8-35

LIGHTS

2. Be sure the headlight switch is in the “OFF”

position.

3. Remove the fuse box cover.

Low-beam:

HEADLIGHTS

LED headlight bulb

If replacement is required, contact a NISSAN

dealer.

4. Pinch the locking tabs

found on each

side of the extended storage fuse switch.

5. Pull the extended storage fuse switch

Halogen headlight bulb

straight out from the fuse box

The halogen headlight is a semi-sealed beam

type which uses replaceable headlight (halo-

gen) bulbs. They can be replaced from inside

the engine compartment without removing the

headlight assembly.

How to remove the extended storage fuse

switch:

1. To remove the extended storage fuse

switch, be sure the ignition switch is in the

“OFF” or “LOCK” position.

CAUTION:

2. Be sure the headlight switch is in the “OFF”

position.

High-pressure halogen gas is sealed inside

the bulb. The bulb may break if the glass

envelope is scratched or the bulb is dropped.

3. Remove the fuse box cover.

4. Pinch the locking tabs

found on each

side of the extended storage fuse switch.

5. Pull the extended storage fuse switch

straight out from the fuse box

JVM0395X

Disconnect the battery negative cable.

Disconnect the electrical connector

from the rear end of the bulb.

Remove the headlight bulb by turning it

counter clockwise. Do not shake or rotate

the bulb when removing it.

Install the new bulb in the reverse order of

removal.

8-36 Maintenance and do-it-yourself

Maintenance and do-it-yourself -> Fuses for Your Nissan X Trail SUV 2020

Popular Manuals