Get Pre-driving checks and adjustments -> Back door Guide for Nissan X Trail SUV 2020

BACK DOOR

pushing the back door request switch (if

equipped).

the Intelligent Key.

WARNING:

NOTE:

pushing the door handle request switch (if

Always be sure the back door has been

For models with motion-activated back

door: When washing, waxing or maintain-

ing your vehicle, placing or replacing the

body cover, or splashing water to the

area around the kick motion sensor,

place the power back door main switch

equipped).

closed securely to prevent it from open-

pushing the power door lock switch to the

unlock position.

ing while driving.

Do not drive with the back door open.

This could allow dangerous exhaust

gases to be drawn into the vehicle. See

“Precautions when starting and driving”

(P.5-4) for exhaust gas.

Do not leave children unattended inside

the vehicle. They could unknowingly acti-

vate switches or controls. Unattended

children could become involved in ser-

ious accidents.

To close the back door, pull down until it

securely locks.

in the “OFF”

position.

OPERATING POWER BACK DOOR (if

equipped)

If the power open or close operation is

performed consecutively, the safety

mode activates and the operation cannot

be performed for a certain period of time.

In this case, wait for a while and then

perform the operation.

To operate the power back door, the shift lever

must be in the “P” (Park) position.

The power back door will not operate if the

battery voltage is low.

Always be sure that hands and feet are

clear of the door frame to avoid injury

while closing the back door.

Power open (using switches)

Power back door main switch (if

equipped)

OPERATING MANUAL BACK DOOR

JVP0484X

Power back door switch — Instrument panel

JVP0483X

Power open/close (switch operation)

Manual operation

The power back door operation can be turned

on or off with the power back door main switch

on the instrument panel.

JVP0481X

To open the back door, unlock it and push the

opener switch . Pull up the back door to open.

The back door can be unlocked by:

When the power door main switch is pushed to

the “OFF” position , power operation is avail-

able by using the power back door button on

pushing the “UNLOCK”

button on the

key.

3-28 Pre-driving checks and adjustments

door will fully open automatically by:

pushing the power back door switch

the lower part of the back door

pushing the power back door switch

pushing the power back door button

the instrument panel for more than

second

the key

And then the power back door will move in the

reverse direction if one of the above actions is

performed again.

pushing the back door opener switch

pushing the power back door button

the key for more than 1 second

The outside chime sounds when the back door

The hazard indicator flashes

times (if

starts to reverse.

equipped) and the outside chime sounds

Reverse function (using switches) (if

equipped)

NOTE:

JVP0485X

The back door can be opened by the power

Back door opener switch

back door switch

button

or the power back door

The power back door will reverse immediately if

one of the following actions is performed

during power open or power close.

even if the back door is

locked. The back door can be unlocked and

opened independently of the other doors,

even when they are locked.

pushing the power back door switch

the instrument panel

Power close (using switches)

pushing the power back door switch

the lower part of the back door

When the back door is fully opened, the back

door will fully close automatically by:

pushing the power back door button

on the key.

pushing the power back door switch

the instrument panel

The hazard flashes 4 times and the outside

chime sounds when the back door starts to

reverse.

pushing the power back door switch

SPA2562

Power back door button - Key (example)

the lower part of the back door

pushing the power back door button

the key for more than 1 second

Auto reverse function

The auto-reverse function enables the back

door to automatically reverse when something

is caught in the back door as it is opening or

closing. When the control unit detects an

obstacle, the back door will reverse and return

to the full open or full close position.

The hazard flashes 4 times (if equipped) and

the outside chime sounds when the back door

starts closing.

Stop and reverse function (if equipped)

The power back door will stop immediately if

one of the following actions is performed

during power open or close.

If a second obstacle is detected, the back door

motion will stop. The back door will enter the

manual mode.

A pinch sensor is mounted on each side of the

back door. If an obstacle is detected by the

pinch sensor during power close, the back door

will reverse and return to the full open position

pushing the power back door switch

pushing the back door opener switch

JVP0285X

Power back door switch — Back door

When the back door is fully closed, the back

Pre-driving checks and adjustments 3-29

immediately.

NOTE:

MOTION-ACTIVATED BACK DOOR (if

equipped)

The kick motion sensor may not function

NOTE:

under the following conditions:

If the pinch sensor is damaged or removed,

— When operating near a location where

strong radio waves are transmitted,

such as a TV tower, power station or

broadcasting station.

the power close function will not operate.

WARNING:

— When the vehicle is parked near

There is a small distance immediately before

the closed position that cannot be detected.

Make sure that all passengers keep their

hands, etc., clear from the back door opening

before closing the back door.

parking meter.

The power back door may not operate

when your foot remains in the operating

range

The kick motion sensor function may not

detect

a kicking motion underneath a

Manual mode

JVP0486X

tow-bar (if equipped), however the nor-

mal functionality is retained either side of

the tow-bar (if equipped).

If power operation is not available, the back

door can be operated manually. Power opera-

tion may not be available if multiple obstacles

have been detected in a single power cycle or if

the battery voltage is low. When the power

back door main switch is in the OFF position,

the back door can be opened manually by

pushing the back door opener switch (if

equipped). If the power back door opener

switch is pushed during power open or close,

the power operation will be canceled and the

back door can be operated manually.

CAUTION:

When the Intelligent Key is carried with

you near the back door, even someone,

who does not carry the Intelligent Key,

may be able to open or close the back

door with a kick motion.

Do not perform a kick motion near the

exhaust system components while they

are hot. You may severely burn yourself.

JVP0487X

The kick motion sensor , located on the back

of the rear bumper, enables you to open or

close the back door in hands-free.

Do not perform

a kick motion on an

unstable place (for example, on a slope

or a muddy ground, etc.).

When you move your foot under and away

from the operating range

similarly to a

kicking motion, the back door will open or

close automatically.

3-30 Pre-driving checks and adjustments

position setting. To change the position of the

back door, repeat steps 1-3 for setting the

position of the back door.

Power open or close function

BACK DOOR RELEASE LEVER

The back door will fully open automatically

using the kick motion sensor.

1. Carry the Intelligent Key.

CAUTION:

2. Move your foot under and away from the

rear bumper similarly to a kicking motion

within the operation range of the kick

motion sensor.

Do not set the height of the back door below

approximately 1/3 of the way to the floor

using garage mode. Even if you set the

height below approximately 1/3 of the way

to the floor, the height will automatically be

set to approximately 1/3 of the way to the

floor.

3. The back door will automatically open or

close.

Stop and reverse function

JVP0280X

The power back door will stop immediately if a

kick motion is performed during power open or

close. The back door can be stopped even if

you do not carry the Intelligent Key.

If the back door cannot be opened with the

power door lock switch due to a discharged

battery, follow these steps.

And then the power back door will move in the

reverse direction if a kick motion is performed

again. The power back door can be reversed

when you carry the Intelligent Key.

1. Fold the rear seats down. See “Seats” (P.1-2).

2. Insert a suitable tool in the access opening.

Move the release lever to the right. The

back door will be unlatched.

3. Push the back door up to open.

AUTO CLOSURE (if equipped)

Contact a NISSAN dealer as soon as possible for

If the back door is pulled down to a partly open

position, the back door will pull itself to the

closed position.

repair.

GARAGE MODE SYSTEM

Do not apply excessive force when the auto

closure is operating. Excessive force applied

may cause the mechanism to malfunction.

The back door can be set to open to a specific

height by performing the following:

1. Open the back door.

CAUTION:

2. Pull the back door down to the desired

position and hold the back door (the back

door will have some resistance when being

manually adjusted).

3. While holding the back door in position,

press and hold the back door switch

located on the back door for approximately

3 seconds or until 2 beeps are heard.

The back door will automatically close

from

a partly open position. To avoid

pinching, keep hands and fingers away

from back door opening.

Do not let children operate the back door.

The back door will open to the selected

Pre-driving checks and adjustments 3-31

Pre-driving checks and adjustments -> Back door for Your Nissan X Trail SUV 2020

Popular Manuals