Get Pre-driving checks and adjustments -> Security system Guide for Nissan X Trail SUV 2020

SECURITY SYSTEM

Your vehicle has either or both of the following

security systems:

Hazard indicator mode (except for South Africa and Europe)

DOOR UNLOCK

HAZARD - none

Theft warning

Operation

DOOR LOCK

NISSAN Anti-theft System (NATS)*

Intelligent Key system (using

The security condition will be shown by the

door handle or back door re- HAZARD - twice

security indicator light.

quest switch)

(* immobilizer)

Remote keyless entry system

HAZARD - twice

(using

button)

THEFT WARNING SYSTEM (if equipped)

The theft warning system provides visual and

audio alarm signals if parts of the vehicle are

disturbed.

Hazard indicator and horn mode (except for South Africa and Europe)

DOOR UNLOCK

Operation

DOOR LOCK

Intelligent Key system (using

door handle or back door re-

quest switch)

HAZARD - once

HAZARD - twice

Security indicator light

OUTSIDE CHIME - once

OUTSIDE CHIME - twice

HAZARD - once

HORN - none

Remote keyless entry system HAZARD - twice

(using or button) HORN - once

Switching procedure (if equipped)

To switch the hazard indicator and horn

(chime) operation, push the LOCK

and

UNLOCK

buttons on the Intelligent Key

simultaneously for more than 2.5 seconds.

When the hazard indicator mode is set, the

hazard indicator flashes 3 times.

When the hazard indicator and horn mode

are set, the hazard indicator flashes once

and the horn chirps once.

SIC2045

The security indicator light, located on the

meter panel, operates whenever the ignition

switch is in the “LOCK” or “OFF” position. This is

normal.

3-22 Pre-driving checks and adjustments

Theft warning system operation:

Cancel switch for ultrasonic sensor:

For models with ultrasonic sensor

How to activate system:

The warning system will give the following

alarm:

1. Close all windows and sunroof (if

The hazard indicator blinks and the alarm

sounds intermittently for approximately 30

seconds. (The alarm will repeat 8 times.)

The alarm automatically turns off after

approximately 30 seconds. However, the

alarm reactivates if the vehicle is tampered

with again.

equipped).

2. Place the ignition switch in the “OFF”

position.

3. Carry the remote controller or the Intelli-

gent Key with you and get out of the

vehicle.

4. Make sure the hood and the back door are

closed. Close and lock all doors with the

remote controller, the Intelligent Key or the

request switch.

The alarm is activated when:

operating the door or the back door with-

out using the remote controller, the Intel-

ligent Key or the request switch.

JVP0311X

The ultrasonic sensors

(volumetric sensing),

If a door or the hood is open, the buzzer will

sound. The buzzer will stop when the door

is correctly closed.

opening the hood (if equipped).

located on the ceiling, detect movement in the

passenger’s compartment. When the theft

warning system is set to the armed position,

it will automatically switch on the ultrasonic

sensor.

the volumetric sensing system (ultrasonic

sensors) is triggered (when it is activated).

5. Confirm that the security indicator light

comes on. The security indicator light

blinks rapidly for approximately 20 seconds

and then blinks slowly. The system is now

activated. If, during this 20-second time

period, the door is unlocked by the remote

controller, the Intelligent Key or the request

switch, or the ignition switch is placed in

the “ON” position, the system will not

activate.

the power supply is disconnected.

How to stop alarm:

It is possible to exclude the ultrasonic (for

example, when leaving pets inside the car or

transporting the vehicle on a ferry).

To exclude the ultrasonic:

1. Close all the windows.

The alarm will stop by unlocking a door

with the request switch (if equipped) or the

“UNLOCK”

Key.

button on the Intelligent

The alarm will stop if the ignition switch is

placed in the “ON” position.

2. Place the ignition switch in the “OFF”

position.

Even when the driver and/or passengers are

in the vehicle, the system will activate with all

doors locked and the ignition switch off.

Place the ignition switch in the “ON” position

to turn the system off.

If the system malfunctions, the short beep

sounds 5 times when the system is activated.

Have the system checked by a NISSAN dealer.

3. Push the cancel switch

located on the

ceiling. The security indicator light will start

flashing rapidly.

4. Close the doors, hood and back door. Lock

them using the remote controller, the

Intelligent Key or the request switch. The

security indicator light will start flashing

faster and a buzzer will sound once.

The ultrasonic sensor is now excluded from the

theft warning system. All other functions of the

system remain activated until the theft warning

system is disarmed again.

Pre-driving checks and adjustments 3-23

1. Remove any items that may be causing the

interference away from the NATS key.

Theft warning system operation:

For models without ultrasonic sensor

How to activate system:

The vehicle security system will give the

2. Leave the ignition switch in the “ON” posi-

following alarm:

1. Close all windows and sunroof (if

tion for approximately 5 seconds.

The hazard indicator or headlight blinks

and the horn sounds intermittently.

The alarm automatically turns off after

approximately 30 or 50 seconds. However,

the alarm reactivates if the vehicle is

tampered with again.

equipped).

3. Place the ignition switch in the “OFF” or

“LOCK” position, and wait approximately 10

seconds.

4. Repeat steps 2 and 3 again.

5. Start the engine.

The system can be armed even if the

windows are open.

2. Place the ignition switch in the “OFF”

position.

3. Remove remote controller or the Intelligent

Key from the vehicle.

4. Close all doors, hood and back door. Lock

all doors. The doors can be locked with

remote controller or the Intelligent Key,

door handle request switch, power door

lock switch or mechanical key.

5. Confirm that the security indicator light

comes on. The security indicator light stays

on for about 30 seconds. The vehicle

security system is now pre-armed. After

about 30 seconds the vehicle security

system automatically shifts into the armed

phase. The security light begins to flash

The alarm is activated by:

6. Repeat the steps above until all possible

Unlocking the door or opening the back

door without using the button on the

remote controller or the Intelligent Key,

the door handle request switch or the

mechanical key. (Even if the door is opened

by releasing the door inside lock knob, the

alarm will activate.)

interferences are eliminated.

If this procedure allows the engine to start,

NISSAN recommends placing the registered

NATS key separate from other devices to avoid

interference.

FCC Notice:

For USA:

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following

two conditions: (1) This device may not cause

harmful interference, and (2) this device must

accept any interference received, including

interference that may cause undesired op-

eration.

Note: Changes or modifications not expressly

approved by the party responsible for com-

pliance could void the user’s authority to

operate the equipment.

Opening the hood.

How to stop alarm:

The alarm will stop only by unlocking a

door by pushing the “UNLOCK” button on

the remote controller or the Intelligent Key.

The alarm will not stop if the ignition switch

once every approximately

3 seconds. If,

is placed in the “ON” position.

during this 30 seconds pre-arm time peri-

od, the door is unlocked, or the ignition

switch is placed in “ON”, the system will not

alarm.

NISSAN ANTI-THEFT SYSTEM (NATS)

The NISSAN Anti-Theft System (NATS) will not

allow the engine to start without the use of the

registered NATS key.

If the engine does not start using the registered

NATS key, it may be due to interference caused

by:

Even when the driver and/or passengers are

in the vehicle, the system will activate with all

doors, hood, and back door locked with the

ignition switch in the “LOCK” position. When

placing the ignition switch in the “ON” posi-

tion, the system will be released.

For Canada:

This device complies with Industry Canada

licence-exempt RSS standard(s). Operation is

subject to the following two conditions: (1)

this device may not cause interference, and

(2) this device must accept any interference,

including interference that may cause un-

desired operation of the device.

Another NATS key.

Automated toll road device.

Automated payment device.

Other devices that transmit similar signals.

Start the engine using the following procedure:

3-24 Pre-driving checks and adjustments

REMOTE ENGINE START (if equipped)

Security indicator light

REMOTE ENGINE START OPERATING

RANGE

WARNING:

To help avoid risk of injury or death through

unintended operation of the vehicle and/or

its systems, do not leave children, people

who require the assistance of others or pets

unattended in your vehicle. Additionally, the

temperature inside

a closed vehicle on a

warm day can quickly become high enough

to cause a significant risk of injury or death

to people and pets.

JVP0445X

SIC2045

The remote engine start

button is on the

Intelligent Key if the vehicle has remote engine

start function. This function allows the engine

to start from outside the vehicle.

Some systems, such as the air conditioner

system, will turn on during a remote engine

start, if the system was on the last time the

ignition switch was turned off.

The security indicator light is located on the

meter panel. It indicates the status of NATS.

The light operates whenever the ignition

switch is in the “LOCK”, “OFF” or “ACC” position.

The security indicator light indicates that the

security systems on the vehicle are operational.

If NATS is malfunctioning, this light will remain

on while the ignition switch is in the “ON”

position.

If the light remains on and/or the engine

does not start, contact a NISSAN dealer for

NATS service as soon as possible. Be sure to

bring all NATS keys that you have when

visiting a NISSAN dealer for service.

The remote engine start function can only be

used when the Intelligent Key is within the

specified operating range from the vehicle.

When the Intelligent Key battery is discharged

or other strong radio wave sources are present

near the operating location, the Intelligent Key

operating range becomes narrower, and the

Intelligent Key may not function properly.

Laws in some local communities may restrict

the use of remote engine starters. For example,

The remote engine start operating range is

some laws require

a person using remote

approximately 60 m (197 ft) from the vehicle.

engine start to have the vehicle in view. Check

local regulations for any requirements.

REMOTE STARTING THE ENGINE

Other conditions may affect the remote engine

start function. See “Conditions the remote

engine start will not work” (P.3-26).

Other conditions can affect the performance of

the Intelligent Key transmitter. See “Intelligent

Key system” (P.5-14) for additional information.

To use the remote engine start function to

start the engine, perform the following:

1. Aim the Intelligent Key at the vehicle.

2. Push the “LOCK”

button to lock all

doors.

3. Within 5 seconds push and hold the remote

engine start

button until the turn

signal lights flash and the tail lights illumi-

nate. If the vehicle is not within view, push

and hold the remote engine start

button for at least 2 seconds.

The following events will occur when the

Pre-driving checks and adjustments 3-25

Pre-driving checks and adjustments -> Security system for Your Nissan X Trail SUV 2020

Popular Manuals