Get Access -> Alarm Guide for Peugeot 208 4 Door 2020

Access

System which protects and provides a deterrent

against theft and break-ins.

Boot

Exterior perimeter monitoring

Opening

► After unlocking the vehicle or just the boot,

press the opening control and then raise the

tailgate.

The system checks for opening of the vehicle.

The alarm is triggered if anyone tries to open a

door, the boot or the bonnet, for example.

Interior volumetric monitoring

► Insert a small screwdriver into hole A of the

lock to unlock the boot.

► Move the latch to the left.

Closing

► Lower the tailgate using one of the interior

grab handles.

The system checks for any variation in volume in

the passenger compartment.

The alarm is triggered if anyone breaks a

window, enters the passenger compartment or

moves inside the vehicle.

If the tailgate is not properly closed, this

warning lamp comes on accompanied by

a message, if the engine is running, and an

audible signal, if the vehicle is travelling at more

than 6 mph (10 km/h).

Locking after closing

If the fault persists after closing again, the boot

will remain locked.

Self-protection function

The system checks for the putting out of service

of its components.

The alarm is triggered if the battery, the central

control or the siren wiring is put out of service or

damaged.

In the event of a fault with the central

locking system, it is essential to

disconnect the battery to lock the boot and so

ensure complete locking of the vehicle.

In the event of a malfunction or if you

experience diﬃculty opening or closing

the tailgate, have it checked by a PEUGEOT

dealer or a qualiﬁed workshop without delay,

to avoid the issue deteriorating and prevent

any risk of the tailgate dropping, potentially

causing serious injury.

For all work on the alarm system, contact

a PEUGEOT dealer or a qualiﬁed

workshop.

Alarm

(Depending on version)

Locking the vehicle with full

alarm system

Back-up release

To manually unlock the boot in the event of a

battery or central locking failure.

Activation

► Switch oﬀ the ignition and exit the vehicle.

Unlocking

► Fold the rear seats to gain access to the lock

from inside the boot.

Access

► Lock or deadlock the vehicle using the

remote control or by pressing on the driver's

door handle.

When the monitoring system is active, the red

indicator lamp in the button ﬂashes once per

second and the direction indicators come on for

about 2 seconds.

The exterior perimeter monitoring is activated

after 5 seconds and the interior volumetric

monitoring after 45 seconds.

sidelamps and/or the daytime running lamps

ﬂash for about 2 seconds.

Only exterior perimeter monitoring is activated;

the red indicator lamp in the button ﬂashes every

second.

To take eﬀect, this deactivation must be

performed whenever the ignition is switched

oﬀ.

After unlocking using the remote

control

If the vehicle automatically locks itself again

(as happens if a door or the boot is not

opened within 30 seconds of unlocking), the

monitoring system is automatically activated.

Reactivating interior volumetric

monitoring

► Deactivate exterior perimeter monitoring by

unlocking the vehicle using the remote control or

the "Keyless Entry and Starting" system.

The indicator lamp in the button goes oﬀ.

► Reactivate the full alarm system by locking

the vehicle using the remote control or by

pressing the driver’s door handle.

Locking the vehicle

with exterior perimeter

monitoring only

Disable volumetric monitoring to avoid unwanted

alarm triggering in certain cases, such as:

– Slightly open window.

The alarm does not activate when

locking automatically from a distance.

If an opening (door, boot or bonnet) is not

properly closed, the vehicle is not locked,

but the exterior perimeter monitoring will be

activated after 45 seconds, at the same time

as the interior volumetric monitoring.

The red indicator lamp in the button once again

ﬂashes every second.

– Washing the vehicle.

– Changing a wheel.

Triggering of the alarm

This is indicated by sounding of the siren

and ﬂashing of the direction indicators for 30

seconds.

Depending on the country of sale, certain

monitoring functions remain active until the alarm

has been triggered eleven times consecutively.

When the vehicle is unlocked using the remote

control or the Keyless Entry and Starting system,

rapid ﬂashing of the red indicator lamp in the

button informs you that the alarm was triggered

during your absence. When the ignition is

switched on, this ﬂashing stops.

– Towing your vehicle.

– Transport on a ship or ferry.

Deactivation

► Press one of the remote control unlocking

buttons:

Deactivating interior volumetric

monitoring

► Switch oﬀ the ignition and within 10 seconds

press the alarm button until the indicator lamp is

on ﬁxed.

short press

long press

► Exit the vehicle.

► Immediately lock the vehicle using the remote

control or the "Keyless Entry and Starting"

system.

► Unlock the vehicle by pressing the driver’s

door handle.

The monitoring system is deactivated: the

indicator lamp in the button goes oﬀ and the

Access

Operating the switch again stops the movement

of the window.

Failure of the remote control

To deactivate the monitoring functions:

► Unlock the vehicle using the key in the

driver's door lock.

► Open the door; the alarm is triggered.

► Switch on the ignition; this stops the alarm.

The indicator lamp in the button goes oﬀ.

Electric windows

Window controls remain operational for

approximately 45 seconds after switching

oﬀ the ignition or after locking the vehicle.

After that time, the controls are disabled.

To reactivate them, switch on the ignition or

unlock the vehicle.

1. Left-hand front

2. Right-hand front

Locking the vehicle without

activating the alarm

► Lock or deadlock the vehicle using the key

(integral to the remote control) in the driver's

door lock.

3. Right-hand rear (depending on version)

4. Left-hand rear (depending on version)

5. Deactivation of the electric window controls

located by the rear seats (depending on

version)

Anti-pinch

(Depending on version)

If the window meets an obstacle while rising, it

stops and immediately partially lowers again.

Locking the rear doors - Electric child lock

(depending on version)

Deactivating the rear

controls for the rear electric

windows

Malfunction

When the ignition is switched on, ﬁxed

illumination of the red indicator lamp in the

button indicates a malfunction of the system.

Have it checked by a PEUGEOT dealer or a

qualiﬁed workshop.

For more information on the Electric child lock,

refer to the corresponding section.

Manual operation

► To open/close the window, press/pull the

switch without passing the point of resistance;

the window stops as soon as the switch is

released.

Automatic activation

(Depending on country of sale)

The system is activated automatically 2 minutes

after the last door or the boot is closed.

► To avoid triggering the alarm on entering the

vehicle, ﬁrst press the unlocking button on the

remote control or unlock the vehicle using the

“Keyless Entry and Starting” system.

For your children's safety, press control 5 to

deactivate the controls for the rear electric

windows, irrespective of their positions.

The red indicator lamp in the button comes

on and a conﬁrmation message is displayed.

The lamp will remain lit until the controls are

reactivated.

Automatic operation

(Depending on version)

► To open/close the window, press/pull the

switch past its resistance point: the window

opens/closes completely when the switch is

released.

Access -> Alarm for Your Peugeot 208 4 Door 2020

Popular Manuals