2008-2015 Peugeot 3008 SUV Monitoring User Manual

MY CAR USER MANUAL

Monitoring for Your Peugeot 3008 SUV First Generation (2008-2015)

Monitoring  
Instruments  
1. Rev counter.  
Instrument panels  
Indicates the engine speed (x 1 000 rpm).  
2. Coolant temperature gauge.  
Indicates the temperature of the engine  
coolant (° Celsius).  
3. Fuel gauge.  
Indicates the quantity of fuel remaining in  
the tank.  
4. Speedometer.  
Indicates the current speed of the moving  
vehicle (mph or km/h).  
5. Screen.  
6. Control switch.  
Temporary display of the service indicator  
and driving range with the AdBlue®  
additive.  
Display and reset the selected function (trip  
distance recorder or service indicator).  
7. Instrument panel lighting dimmer.  
Adjusts the brightness of the lighting of  
the instruments and controls, if the vehicle  
lighting is on.  
For more information, refer to the  
section corresponding to the button or  
function and its associated display.  
Panel grouping together the vehicle operation indication dials and warning lamps.  
14  
Monitoring  
Screen(s)  
1
A. Speed limiter  
or  
Cruise control.  
(mph or km/h)  
B. Trip distance recorder.  
(miles or km)  
C. Service indicator.  
(miles or km) or,  
Engine oil level indicator (depending  
on version).  
or  
distance recorder.  
(miles or km)  
D. Gear shift indicator.  
Electronic or automatic gearbox.  
E. Warning messages and function  
status messages, trip computer,  
GPS navigation information.  
15  
Monitoring  
Indicator and warning lamps  
Visual indicators informing the driver that a system is in operation (operation or deactivation indicator lamps) or of the occurrence of a fault (warning  
lamp).  
When the ignition is switched on  
Associated warnings  
The warning lamps may come on  
continuously (fixed) or flash.  
Certain warning lamps come on for a  
few seconds when the vehicle's ignition is  
switched on.  
When the engine is started, these same  
warning lamps should go off.  
The illumination of certain warning lamps may  
be accompanied by an audible signal and a  
message in the multifunction screen.  
Certain warning lamps may come on  
in one of two different modes. Only by  
relating the type of illumination to the  
operating status of the vehicle can it  
be ascertained whether the situation is  
normal or whether a fault has occurred.  
If they remain on, before moving off, refer to the  
information on the warning lamp concerned.  
Operation indicator lamps  
If one of the following indicator lamps comes on, this confirms that the corresponding system has come into operation.  
Warning/indicator lamp  
is on  
Cause  
Action / Observations  
Left-hand  
flashing with buzzer.  
The lighting stalk is pushed down.  
direction indicator  
Right-hand  
flashing with buzzer.  
The lighting stalk is pushed up.  
direction indicator  
Sidelamps  
fixed.  
fixed.  
fixed.  
The lighting stalk is in the  
"Sidelamps" position.  
Dipped beam  
headlamps  
The lighting stalk is in the "Dipped  
beam headlamps" position.  
Main beam  
headlamps  
The lighting stalk is pulled towards  
you.  
Pull the stalk to return to dipped beam headlamps.  
16  
Monitoring  
1
Warning/indicator lamp  
Front foglamps  
is on  
Cause  
Action / Observations  
fixed.  
The front foglamps are switched on  
using the ring on the lighting control  
stalk.  
Turn the ring on the lighting control stalk rearward  
twice to switch off the front foglamps.  
Rear foglamps  
fixed.  
fixed.  
fixed.  
The rear foglamps are on.  
Turn the ring on the stalk rearward to switch off the  
rear foglamps.  
Diesel engine  
pre-heating  
The ignition switch is at the  
2nd position (ignition on).  
Wait until the warning lamp has switched off before starting.  
The duration for which the warning lamp is on is  
determined by the climatic conditions.  
Release the electric parking brake to switch off the  
warning lamp: with your foot on the brake pedal, pull  
the electric parking brake control lever.  
Electric parking  
brake  
The electric parking brake is applied.  
Observe the safety recommendations.  
For more information on the electric parking brake,  
refer to the corresponding section.  
Deactivation of  
the automatic  
functions of the  
electric parking  
brake  
fixed.  
The "automatic application"  
(on switching off the engine) and  
"automatic release" functions are  
deactivated or faulty.  
Activate the function (depending on the country of  
sale) via the vehicle configuration menu or contact a  
PEUGEOT dealer or a qualified workshop if automatic  
application / release is not possible.  
For more information on the electric parking brake,  
refer to the corresponding section.  
17  
Monitoring  
Warning/indicator lamp  
is on  
Cause  
Action / Observations  
Foot on the  
brake pedal  
fixed.  
The brake pedal is not pressed.  
You must press the brake pedal firmly to:  
-
start the engine with an electronic gearbox (lever  
in position N),  
-
manually release the parking brake.  
With an electronic gearbox, if you  
hold the vehicle on an incline using  
the accelerator for too long, the  
clutch overheats.  
flashing.  
Use the brake pedal and/or the electric parking brake.  
Parking space  
sensors  
fixed.  
The parking space sensors function  
is active.  
Press the corresponding button to deactivate it.  
flashing.  
fixed.  
The system is measuring the space.  
Once the measurement has been done, the warning  
lamp comes on fixed again.  
When the vehicle stops (red lights,  
traffic jams, ...) the Stop & Start  
system has put the engine into STOP  
mode.  
Stop & Start  
The warning lamp goes off and the engine restarts  
automatically in START mode, as soon as you want to  
move off.  
STOP mode is temporarily  
unavailable.  
or  
flashes for a few  
seconds, then  
goes off.  
For more information on Stop & Start, refer to the  
corresponding section.  
START mode is invoked  
automatically.  
18  
Monitoring  
Deactivation indicator lamps  
If one of the following indicator lamps comes on, this confirms that the corresponding system has been switched off intentionally.  
This is may be accompanied by an audible signal and a message in the multifunction screen.  
1
Warning/indicator lamp  
is on  
Cause  
Action / Observations  
Passenger's  
fixed.  
The control, located in the glove box, Set the control to the ON position to activate the  
airbag system  
is set to the OFF position.  
The passenger's front airbag is  
deactivated.  
passenger's front airbag.  
In this case, do not fit a child seat in the rearward  
facing position.  
You can install a rearward facing  
child seat, unless there is a fault with  
the operation of the airbags (Airbag  
warning lamp on).  
Warning lamps  
When the engine is running or the vehicle is being driven, the illumination of one of the following warning lamps indicates a fault which requires action  
on the part of the driver.  
Any fault resulting in the illumination of a warning lamp must be investigated further by reading the associated message in the multifunction screen.  
If you encounter any problems, do not hesitate to contact a PEUGEOT dealer or a qualified workshop.  
Warning/indicator lamp  
STOP  
is on  
Cause  
Action / Observations  
fixed, alone or  
associated with  
another warning lamp,  
accompanied by an  
audible signal and a  
Illumination of this warning lamp is  
associated with a serious fault with  
the braking system, power steering,  
engine lubrication system or cooling  
Stop as soon as it is safe to do so as there is a risk  
that the engine will cut out while driving.  
Park, switch off the ignition and contact a PEUGEOT  
dealer or a qualified workshop.  
message in the screen. system.  
19  
Monitoring  
Warning/indicator lamp  
Service  
is on  
Cause  
Action / Observations  
temporarily,  
accompanied by a  
message.  
One or more minor faults for which  
there is no specific warning lamp  
have been detected.  
Identify the cause of the fault using the message  
displayed in the screen.  
You can deal with some problems yourself, such as a  
door open or the start of saturation of the particle filter  
(as soon as the traffic conditions allow, regenerate  
the filter by driving at a speed of at least 40 mph  
(60 km/h), until the warning lamp goes off).  
For any other problems, such as a fault with the tyre  
under inflation detection system, contact a PEUGEOT  
dealer or a qualified workshop.  
fixed, accompanied by One or more major faults for which  
Identify the cause of the fault using the message  
displayed in the screen; you must then contact a  
PEUGEOT dealer or a qualified workshop.  
a message.  
there is no specific warning lamp  
have been detected.  
fixed, associated  
with the flashing and  
then fixed display of  
the service indicator  
spanner.  
The servicing interval has been  
exceeded.  
Only on BlueHDi Diesel versions.  
Your vehicle must be serviced as soon as possible.  
20  
Monitoring  
1
Warning/indicator lamp  
is on  
Cause  
Action / Observations  
You must stop as soon as it is safe to do so.  
Electric parking  
brake  
flashing.  
The electric parking brake is not  
applied automatically.  
The application/release is faulty.  
Park on flat level ground, engage a gear (or place the  
lever in position P for an automatic gearbox), switch  
off the ignition and contact a PEUGEOT dealer or a  
qualified workshop.  
Contact a PEUGEOT dealer or a qualified workshop  
without delay.  
Electric parking  
brake fault  
fixed.  
The electric parking brake has a fault.  
For more information on the electric parking brake,  
refer to the corresponding section.  
You must stop as soon as it is safe to do so.  
Top up with brake fluid recommended by PEUGEOT.  
If the problem persists, have the system checked by a  
PEUGEOT dealer or a qualified workshop.  
Braking  
fixed, associated with  
the STOP warning  
lamp.  
The braking system fluid level has  
dropped significantly.  
+
+
fixed, associated with the The braking system has a fault.  
electric parking brake  
malfunction warning  
lamp, if the parking brake  
is released.  
You must stop as soon as it is safe to do so.  
Park, switch off the ignition and contact a PEUGEOT  
dealer or a qualified workshop.  
fixed, associated with  
the STOP and ABS  
warning lamps.  
The electronic brake force distribution You must stop as soon as it is safe to do so.  
(EBFD) system has a fault.  
Have it checked by a PEUGEOT dealer or a qualified  
workshop.  
Anti-lock  
Braking System  
(ABS)  
fixed.  
The anti-lock braking system has a  
fault.  
The vehicle retains conventional braking.  
Drive carefully at reduced speed and contact a  
PEUGEOT dealer or a qualified workshop without  
delay.  
21  
Monitoring  
Warning/indicator lamp  
is on  
Cause  
Action / Observations  
Dynamic  
stability control  
(DSC/ASR)  
flashing.  
The DSC/ASR regulation is  
operating.  
The system optimises traction and improves the  
directional stability of the vehicle in the event of loss of  
grip or trajectory.  
fixed.  
The DSC/ASR system has a fault.  
Have it checked by a PEUGEOT dealer or a qualified  
workshop.  
Engine  
flashing.  
The engine management system has Risk of destruction of the catalytic converter.  
autodiagnosis  
system  
a fault.  
Have it checked by a PEUGEOT dealer or a qualified  
workshop.  
The warning lamp should go off when the engine is started.  
If it does not go off, contact a PEUGEOT dealer or qualified  
workshop without delay.  
fixed.  
The emission control system has a  
fault.  
Low fuel level  
fixed with the needle  
in the red zone.  
When it first comes on there remains Refuel as soon as possible to avoid running out of fuel.  
approximately 6 litres of fuel in the  
This warning lamp will come on every time the ignition  
is switched on, until a sufficient addition of fuel is made.  
tank.  
At this point, you begin to use the fuel Fuel tank capacity: approximately 60 litres.  
reserve.  
Never continue to drive until you run out of fuel, as  
this could damage the emission control and injection  
systems.  
Maximum coolant fixed with the needle  
The temperature of the cooling  
system is too high.  
Stop as soon as it is safe to do so.  
Wait until the engine has cooled down before topping  
up the level, if necessary.  
temperature  
in the red zone.  
If the problem persists, contact a PEUGEOT dealer or  
a qualified workshop.  
Engine oil  
pressure  
fixed.  
There is a fault with the engine  
lubrication system.  
You must stop as soon it is safe to do so.  
Park, switch off the ignition and contact a PEUGEOT  
dealer or a qualified workshop.  
22  
Monitoring  
1
Warning/indicator lamp  
is on  
Cause  
Action / Observations  
AdBlue® additive fixed, on switching  
(BlueHDi Diesel) on the ignition,  
accompanied by an  
The remaining driving range is  
between 350 miles (600 km) and  
1500 miles (2400 km).  
Have the AdBlue® additive tank topped up as soon  
as possible: go to a PEUGEOT dealer or a qualified  
workshop, or carry out this operation yourself.  
audible signal and a  
message indicating  
the remaining driving  
range.  
+
flashing associated  
with the SERVICE  
warning lamp,  
The remaining driving range is  
between 0 and 350 miles (600 km).  
You must top-up the AdBlue® additive tank to avoid  
a breakdown: go to a PEUGEOT dealer or a qualified  
workshop, or carry out this operation yourself.  
accompanied by an  
audible signal and a  
message indicating  
the remaining driving  
range.  
flashing, associated  
with the SERVICE  
warning lamp,  
accompanied by an  
audible signal and a  
message indicating  
that starting is  
The AdBlue® tank is empty: the  
starting inhibition system required  
by legislation prevents starting of the  
engine.  
To be able to start the engine, you must top-up the  
AdBlue® additive tank: go to a PEUGEOT dealer  
or a qualified workshop, or carry out this operation  
yourself.  
It is essential to add at least 3.8 litres of AdBlue® to  
the additive tank.  
prevented.  
For topping-up or for more information on the AdBlue® additive, refer to the corresponding section.  
23  
Monitoring  
Warning/indicator lamp  
is on  
Cause  
Action / Observations  
SCR emissions  
control system  
(BlueHDi Diesel) the SERVICE and engine  
diagnostic warning lamps,  
fixed, on switching on the  
ignition, associated with  
A fault with the SCR  
emissions control system has return to normal levels.  
been detected.  
This alert disappears once the exhaust emissions  
+
+
accompanied by an audible  
signal and a message.  
flashing, on switching on  
the ignition, associated with  
the SERVICE and engine  
diagnostic warning lamps,  
accompanied by an audible  
signal and a message  
indicating the remaining  
driving range.  
After confirmation of the fault  
with the emissions control  
system, you can drive for up  
to 650 miles (1 100 km) before  
the engine starting inhibition  
system is triggered.  
Contact a PEUGEOT dealer or a qualified workshop  
without delay, to avoid a breakdown.  
flashing, on switching on  
the ignition, associated with  
the SERVICE and engine  
diagnostic warning lamps,  
accompanied by an audible  
signal and a message.  
You have exceeded the  
authorised driving limit  
following confirmation of  
a fault with the emissions  
control system: the engine  
starting inhibition system  
prevents starting of the  
engine.  
To be able to start the engine, you must call on a  
PEUGEOT dealer or a qualified workshop.  
24  
Monitoring  
1
Warning/indicator lamp  
is on  
Cause  
Action / Observations  
The warning lamp should go off when the engine is  
Battery charge*  
fixed.  
The battery charging circuit has a  
fault (dirty or loose terminals, slack or started.  
cut alternator belt, ...).  
If it does not go off, contact a PEUGEOT dealer or a  
qualified workshop.  
Door(s) open  
fixed if the speed is  
below 6 mph (10 km/h).  
A door, the boot, the lower tailgate  
or the bonnet (with alarm only) is still  
open.  
Close the door or boot.  
fixed and accompanied  
by an audible signal  
if the speed is above  
6 mph (10 km/h).  
Seat belt not  
fastened /  
unfastened  
fixed then flashing  
accompanied by an  
increasing audible  
signal.  
The driver and/or the front passenger Pull the strap then insert the tongue in the buckle.  
has not fastened or has unfastened  
their seat belt.  
Airbags  
temporarily.  
This lamp comes on for a  
few seconds when you turn on the  
ignition, then goes off.  
This lamp should go off when the engine is started.  
If it does not go off, contact a PEUGEOT dealer or a  
qualified workshop.  
fixed.  
One of the airbag or seat belt  
pretensioner systems has a fault.  
Have it checked by a PEUGEOT dealer or a qualified  
workshop.  
Water in Diesel  
fixed.  
The Diesel fuel filter contains water.  
Risk of damage to the injection system on Diesel  
engines.  
Contact a PEUGEOT dealer or a qualified workshop  
without delay.  
* Depending on the country of sale.  
25  
Monitoring  
Warning/indicator lamp  
is on  
Cause  
Action / Observations  
Directional  
headlamps  
flashing.  
The directional headlamps system  
has a fault.  
Have it checked by a PEUGEOT dealer or a qualified  
workshop.  
Under-inflation  
fixed.  
The pressure in one or more wheels  
is too low.  
Check the pressure of the tyres as soon as possible.  
This check should preferably be carried out when the  
tyres are cold.  
+
flashing then fixed,  
accompanied by the  
Service warning lamp. on one of the wheels.  
The tyre pressure monitoring system  
has a fault or no sensor is detected  
Under-inflation detection is not assured.  
Have the system checked by a PEUGEOT dealer or a  
qualified workshop.  
Coolant temperature gauge  
With the engine running, when the needle is:  
After driving for a few minutes, the temperature  
and pressure in the cooling system increase.  
To top up the level:  
-
-
in zone A, the temperature is correct,  
in zone B, the temperature is too high;  
the max temperature warning lamp 1 and  
the central STOP warning lamp come on,  
accompanied by an audible signal and a  
message in the screen.  
F
F
wait for the engine to cool,  
unscrew the cap by two turns to allow the  
pressure to drop,  
F
F
when the pressure has dropped, remove  
the cap,  
top up the level to the "MAX" mark.  
You must stop as soon as it is safe to do so.  
Wait a few minutes before switching off the  
engine.  
Contact a PEUGEOT dealer or a qualified  
workshop.  
26  
Monitoring  
Service indicator  
1
System which informs the driver when the  
next service is due, in accordance with the  
manufacturer's servicing schedule.  
The point at which the service is due is  
calculated from the last indicator zero reset,  
according to the mileage covered since the last  
service.  
For BlueHDi Diesel versions, depending on the  
country of sale, the level of deterioration of the  
engine oil may also be taken into account.  
More than 1 800 miles (3 000 km)  
Less than 600 miles (1 000 km)  
remain before the next service is due  
remain before the next service is due  
When the ignition is switched on, no service  
information appears in the screen.  
Example: 400 miles (900 km) remain before  
the next service is due.  
For 5 seconds after the ignition is switched on,  
the screen indicates:  
Between 600 miles (1 000 km)  
and 1 800 miles (3 000 km) remain  
before the next service is due  
For 5 seconds after the ignition is switched on, the  
spanner symbolising the service operations comes  
on. The distance recorder display line indicates the  
distance remaining before the next service is due.  
Example: 1 700 miles (2 800 km) remain before  
the next service is due.  
5 seconds after the ignition is switched on,  
the distance recorder resumes its normal  
operation. The spanner remains on to  
indicate that a service must be carried out  
soon.  
For 5 seconds after the ignition is switched on, the  
screen indicates:  
5 seconds after the ignition is switched on,  
the spanner goes off; the distance recorder  
resumes its normal operation. The screen then  
indicates the total and trip distances.  
27  
Monitoring  
Service overdue  
For 5 seconds after the ignition is switched on,  
the spanner flashes to indicate that the service  
must be carried out as soon as possible.  
Example: the service is overdue by 180 miles  
(300 km).  
If you have carried out the service on your  
vehicle yourself:  
For BlueHDi versions, the spanner may  
also come on early, according to the  
level of deterioration of the engine oil,  
which depends on the driving conditions  
in which the vehicle is used.  
F
F
switch off the ignition,  
press and hold the trip distance recorder  
zero reset button,  
F
F
switch on the ignition; the distance recorder  
display begins a countdown,  
when the display indicates "=0", release  
the button; the spanner disappears.  
For 5 seconds after the ignition is switched on,  
the screen indicates:  
Resetting the service  
indicator  
If you have to disconnect the battery  
following this operation, lock the vehicle  
and wait at least five minutes for the  
reset to be registered.  
5 seconds after the ignition is switched on,  
the distance recorder resumes its normal  
operation. The spanner remains on.  
Retrieving the service  
information  
You can access the service information at any  
time.  
With BlueHDi Diesel versions, the  
Service warning lamp also comes on  
when the ignition is switched on.  
F
Press the trip distance recorder zero reset  
button.  
The service information is displayed for a  
few seconds, then disappears.  
After each service, the service indicator must  
be reset to zero.  
28  
Monitoring  
Engine oil level indicator*  
1
On versions fitted with an electric oil level  
indicator, the state of the engine oil level  
is displayed in the instrument panel for a  
few seconds when the ignition is switched on,  
after the service information.  
Oil level indicator fault  
The level shown will only be correct  
if the vehicle is on level ground and  
the engine has been off for more than  
30 minutes.  
Oil level correct  
This is signalled by the flashing of "OIL--" or the  
display of a message "Oil level measurement  
invalid" in the instrument panel. Contact a  
PEUGEOT dealer or a qualified workshop.  
In the event of a fault with the electric indicator,  
the engine oil level is no longer monitored.  
When the system has a fault, you should check  
the engine oil level using the manual dipstick  
(located under the bonnet).  
Oil level low  
This is signalled by the flashing of "OIL", or the  
display of a message "Oil level incorrect" in the  
instrument panel, accompanied by illumination  
of the service warning lamp and an audible  
signal.  
Refer to the "Checking levels" section.  
If the low oil level is confirmed by a check using  
the dipstick, the level must be topped up to  
prevent damage to the engine.  
Refer to the "Checking levels" section.  
* Depending on version.  
29  
Monitoring  
Distance recorders  
The total and trip distances are displayed for  
thirty seconds when the ignition is switched off,  
when the driver's door is opened and when the  
vehicle is locked or unlocked.  
Trip distance recorder  
It measures the distance travelled since it was  
reset to zero by the driver.  
Operation  
When the vehicle lighting is on:  
F
press the button to change the brightness  
of the instrument panel,  
F
when the lighting reaches the minimum  
setting, release the button, then press  
again to increase it,  
When travelling abroad, you may  
have to change the units of distance:  
the display of road speed must be in  
the official units (miles or km) for the  
country. The change of units is done via  
the screen configuration menu, with the  
vehicle stationary.  
or  
F
when the lighting reaches the maximum  
setting, release the button, then press  
again to reduce it,  
when the lighting reaches the level of  
brightness required, release the button.  
F
With the ignition on, press the button until  
zeros appear.  
F
Lighting dimmer  
System for manual adjustment of the  
brightness of the instrument panel in relation to  
the exterior brightness.  
When the vehicle lighting is on, you  
cannot switch the instrument panel  
lighting off but you can adjust it to  
minimum.  
Total distance recorder  
It measures the total distance travelled by the  
vehicle since its first registration.  
Dimmer deactivated  
When the lighting is off, or in day mode on  
vehicles fitted with daytime running lamps,  
pressing the button does not have any effect.  
30  
Monitoring  
1
Monochrome screen A (without audio equipment)  
Displays in the screen  
Controls  
Main menu  
F
F
Press the "MENU" button to scroll through  
the various menus of the main menu:  
-
-
-
-
-
vehicle configuration,  
options,  
display settings,  
languages,  
units.  
This displays the following information:  
There are three display control buttons:  
Press the "OK" button to select the menu  
-
-
-
time,  
date,  
-
-
-
"ESC" to abandon the operation in  
progress,  
"MENU" to scroll through the menus or  
sub-menus,  
"OK" to select the menu or sub-menu  
required.  
required.  
ambient temperature* (this flashes if there  
is a risk of ice),  
alert messages,  
trip computer (refer to the end of the  
section).  
-
-
Warning messages (e.g.: "Emission control  
system faulty") or information messages  
(e.g.: "Boot open") may appear temporarily.  
Some can be cleared by pressing the "ESC"  
button.  
* With air conditioning only.  
31  
Monitoring  
Options  
Once the "Options" menu has been selected,  
you can start diagnostics of the status of the  
equipment (active, not active, faulty).  
F
Wait for approximately ten seconds without  
any action to allow the changed data to  
be recorded or press the "ESC" button to  
cancel.  
Date and time  
Once the "Display settings" menu has been  
selected, you have access to the following settings:  
The screen then returns to the normal display.  
Vehicle configuration  
-
-
-
-
-
-
year,  
month,  
day,  
hour,  
minutes,  
12 or 24 hour mode.  
Languages  
Once the "Languages" menu has been  
selected, you can change the language used  
by the display (Français, Italiano, Nederlands,  
Portugues, Portugues-Brasil, Türkçe, Deutsch,  
English, Espanol).  
Once the "Vehicle configuration" menu has  
been selected, you can activate or deactivate  
the following equipment:  
Units  
-
-
-
-
-
-
-
wiper linked with reverse gear (refer to the  
"Visibility" section),  
selective unlocking (refer to the "Access"  
section),  
"guide-me-home" lighting (refer to the  
"Visibility" section),  
directional headlamps (refer to the  
"Visibility" section),  
automatic parking brake** (refer to the  
"Driving" section),  
parking space sensors (refer to the  
"Driving" section),  
Once the "Units" menu has been selected, you  
can change the units for:  
-
-
temperature (°C or °F),  
fuel consumption (l/100 km, mpg or km/l).  
F
Once you have selected a setting, press  
the "OK" button to change its value.  
As a safety measure, configuration of  
the multifunction screen by the driver  
must only be done when stationary.  
** Depending on the country of sale.  
...  
32  
Monitoring  
1
Monochrome screen A (with audio equipment)  
Displays in the screen  
Controls  
Main menu  
F
Press the "MENU" button for access to  
the main menu, then press the "5" or  
"6" buttons to scroll through the various  
menus:  
-
-
-
-
-
-
radio-CD,  
vehicle configuration,  
options,  
display settings,  
languages,  
units.  
From the audio equipment control panel, you  
can:  
F
F
F
press the "MENU" button to gain access to  
the main menu,  
This displays the following information:  
-
-
-
time,  
date,  
press the "5" or "6" buttons to scroll  
through the items on the screen,  
press the "MODE" button to change the  
permanent application (trip computer,  
audio source, ...),  
F
Press the "OK" button to select the menu  
required.  
ambient temperature* (this flashes if there  
is a risk of ice),  
-
-
-
alert messages,  
Radio-CD  
audio sources (radio, CD, ...),  
trip computer (refer to the corresponding  
section).  
F
F
press the "7" or "8" buttons to change a  
setting value,  
press the "OK" button to confirm,  
or  
With the audio equipment switched on, once  
the "Radio-CD" menu has been selected you  
can activate or deactivate the functions linked  
with use of the radio (RDS, REG), the CD or the  
CD changer (introscan, shuffle, CD repeat).  
Warning messages (e.g.: "Emission control  
system faulty") or information messages (e.g.:  
"Boot open") may appear temporarily. Some  
can be cleared by pressing the "<] arrow"  
button.  
F
press this button to abandon the  
operation in progress.  
For more information on the "Radio-  
CD" application, refer to the "Audio  
equipment and telematics" section.  
* With air conditioning only.  
33  
Monitoring  
Vehicle configuration  
Date and time  
Languages  
Once the "Languages" menu has been  
selected, you can change the language used  
by the display.  
Once the "DATE AND TIME" menu has been  
selected, you have access to the following  
settings:  
-
-
-
-
-
-
year,  
month,  
day,  
hour,  
minutes,  
12 or 24 hour mode.  
Units  
Once the "Vehicle Configuration" menu has  
been selected, you can activate or deactivate  
the following equipment:  
Once the "Units" menu has been selected,  
you can change the units of the following  
parameters:  
-
-
-
-
-
-
wiper linked with reverse gear (refer to the  
"Visibility" section),  
selective unlocking (refer to the "Access"  
section),  
guide-me-home lighting (refer to the  
"Visibility" section),  
directional headlamps (refer to the  
"Visibility" section),  
-
-
temperature (°C or °F),  
fuel consumption (l/100 km, mpg or km/l).  
F
Once you have selected a setting, press  
the "7" or "8" buttons to change its value.  
automatic parking brake** (refer to the  
"Driving" section),  
...  
Options  
Once the "Options" menu has been selected,  
you can start diagnostics of the status of the  
equipment (active, not active, faulty).  
F
F
Press the "5" or "6" buttons to switch  
respectively to the previous or next setting.  
Press the "OK" button to record the  
change and return to the normal display or  
press the "<] arrow" button to cancel.  
As a safety measure, configuration of  
the multifunction screen by the driver  
must only be done when stationary.  
** Depending on the country of sale.  
34  
Monitoring  
1
Monochrome screen C (with PEUGEOT Connect Sound (RD5))  
Displays in the screen  
Controls  
Main menu  
F
Press the "MENU" button for access to the  
main menu:  
-
-
audio functions,  
trip computer (see the corresponding  
section),  
From the audio equipment control panel, you  
can:  
-
-
personalisation-configuration,  
telephone (Bluetooth system).  
F
F
F
press the "MENU" button for access to the  
main menu,  
Displays according to context:  
F
Press the "5" or "6" button to select the  
menu required, then confirm by pressing  
the "OK" button.  
-
-
-
time,  
date,  
press the "5" or "6" buttons to scroll  
through the items on the screen,  
press the "MODE" button to change the  
permanent application (trip computer,  
audio source...),  
ambient temperature with air conditioning  
(the value displayed flashes if there is a  
risk of ice),  
"Audio functions" menu  
-
-
audio functions,  
trip computer (see the corresponding  
section),  
F
F
press the "7" or "8" buttons to change a  
setting value,  
press the "OK" button to confirm,  
or  
With the audio equipment switched on, once  
this menu has been selected you can activate  
or deactivate the functions linked with use  
of the radio (RDS, REG, RadioText) or CD  
(introscan, shuffle, CD repeat).  
-
-
alert messages,  
screen and vehicle equipment parameter  
setting menus.  
F
press this button to abandon the  
operation in progress.  
For more information on the "Audio  
functions" application, refer to the  
PEUGEOT Connect Sound (RD5) section.  
35  
Monitoring  
Enter the distance to the  
destination  
"Trip computer"  
menu  
"Personalisation-  
Configuration" menu  
Once this menu has been selected, you can  
consult information concerning the status of the  
vehicle (alert log, status of the functions...).  
F
F
Press the "MENU" button to gain access  
to the general menu.  
Press the arrows, then the "OK" button to  
select the "Trip computer" menu.  
This allows you to enter an approximate value  
for the distance to the final destination.  
Once this menu has been selected, you can  
gain access to the following functions:  
-
-
-
define the vehicle parameters,  
display configuration,  
choice of language.  
Alert log  
This summarises the active warning messages,  
displaying them in succession in the  
multifunction screen.  
Define the vehicle parameters  
Once this menu has been selected, you can  
activate or deactivate the following equipment:  
Status of functions  
-
-
-
-
-
-
wiper linked with reverse gear (refer to the  
"Visibility" section),  
selective unlocking (refer to the "Access"  
section),  
guide-me-home lighting (refer to the  
"Visibility" section),  
directional headlamps (refer to the  
"Visibility" section),  
This summarises the status of the functions  
present on the vehicle.  
F
In the "Trip computer" menu, select one  
of the applications.  
automatic parking brake* (refer to the  
"Driving" section),  
...  
* Depending on the country of sale.  
36  
Monitoring  
1
F
F
Adjust the settings one by one, confirming  
with the "OK" button.  
Press the "5" or "6" button, then the  
"OK" button to select the "OK" box and  
confirm, or the "Back" button to cancel.  
F
Press the "5" or "6" buttons, then the "OK"  
button to select the "OK" box and confirm  
or press the "<] arrow" button to cancel.  
Choice of language  
Once this menu has been selected, you can  
change the screen display language.  
Example: setting of the duration of the guide-  
me-home lighting.  
Display configuration  
Once this menu has been selected, you have  
access to the following settings:  
"Telephone" menu  
F
Press the "5" or "6" buttons, then the  
"OK" button to select the menu required.  
-
-
-
brightness-video setting,  
date and time setting,  
selection of the units.  
With the audio equipment switched on, once  
this menu has been selected you can configure  
your Bluetooth hands-free kit (pairing), consult  
the various telephone directories (calls log,  
services...) and manage your communications  
(accept call, end call, call on hold, secret  
mode...).  
Adjusting the date and time  
F
F
F
Press the "7" or "8" button to select the  
"Display configuration" menu, then the  
"OK" button.  
Press the "5" or "6" button, to select the  
"Adjust date and time" line, then on the  
"OK" button.  
Press the "7" or "8" button to select the  
setting to modify. Confirm by pressing the  
"OK" button then adjust the setting and  
confirm again to save the modification.  
F
Press the "5" or "6" buttons, then the  
"OK" button to select the "Guide-me-home  
headlamps" line.  
For more information on the telephone  
application, refer to the PEUGEOT  
Connect Sound (RD5) section.  
As a safety measure, configuration of  
the multifunction screen by the driver  
must only be done when stationary.  
F
Press the "7" or "8" buttons to set the  
value required (15, 30 or 60 seconds), then  
press the "OK" button to confirm.  
37  
Monitoring  
16/9 retractable colour screen (PEUGEOT Connect Navigation (RT6))  
Displays in the screen  
Controls  
"SETUP" menu  
From the navigation system control panel, to  
select one of the applications:  
F
Press the "SETUP" button to open the  
configuration menu:  
Depending on the context, it displays the  
following information:  
F
press the dedicated "RADIO", "MUSIC",  
"NAV", "TRAFFIC", "PHONE" or  
"SETUP" button for access to the  
corresponding menu,  
-
-
-
-
-
"Display configuration",  
"Speech synthesis setting".  
"Select language",  
"Define vehicle parameters",  
"Alert log".  
-
-
-
-
time,  
date,  
altitude,  
F
F
F
turn the dial A to select a function, an item  
in a list,  
press button B to confirm the selection,  
or  
press the "Back" button to abandon the  
current operation and return to the previous  
display.  
ambient temperature (the value displayed  
flashes if there is a risk of ice),  
parking sensor information,  
parking space measurement,  
audio functions,  
directory and telephone information,  
satellite navigation system information,  
settings menus for the screen, the satellite  
navigation system and vehicle systems.  
the image from the reversing camera.  
For the operation of the retractable  
screen (opening, closing, adjusting the  
position...), refer to the "Access to the  
retractable screen" section.  
-
-
-
-
-
-
With repeated presses on the C "MODE"  
button, the screen displays:  
As a safety measure, configuration of  
the multifunction screen by the driver  
must only be done when stationary.  
-
-
-
-
"RADIO / MEDIA"*,  
"TELEPHONE"*,  
"FULL SCREEN MAP"*,  
"MAP IN A WINDOW"*,  
-
* For more information on these applications,  
refer to the "Audio equipment and telematics"  
section.  
38  
Monitoring  
1
Display configuration  
Adjusting the voice synthesiser  
-
-
"Vehicle access" (refer to the "Access"  
section):  
● "Plip action: all doors, driver only"  
(Selective unlocking of the driver's door),  
"Lighting configuration" (refer to the  
"Visibility" section):  
This menu is used to select the colour scheme  
for the screen, adjust the brightness, set  
the date and time and to choose the units  
for distance (km or miles), fuel consumption  
(l/100 km, mpg or km/l) and temperature  
(°Celsius or °Fahrenheit).  
This menu is used to adjust the volume setting  
for navigation instructions and to choose the  
type of voice (male or female).  
● "Duration of guide me home lighting:  
OFF / 15 s / 30 s / 60 s" (Automatic  
guide me home lighting),  
● "Directional headlights: ON / OFF"  
(Main / additional directional lighting).  
Choice of language  
This menu is used to choose the language  
used by the screen from a defined list.  
Adjusting the date and time  
-
-
-
Press on SETUP.  
Select "Display configuration" and confirm.  
Select "Set date and time" and confirm.  
Vehicle parameters  
Select "Minute adjustment via GPS" so that  
the minutes are adjusted automatically by  
satellite reception.  
This menu is used to activate or deactivate  
certain driving and comfort systems, classified  
by category:  
Alert log  
This lists the active alerts by displaying in turn  
the different messages associated with them.  
-
Select the setting to modify. Confirm by  
pressing on OK, then modify the setting  
and confirm again to save the modification.  
Adjust the settings one by one.  
-
"Driver aid":  
● "Electric brake*" (Automatic electric  
parking brake; refer to the "Driving"  
section),  
-
-
Select "OK" in the screen then confirm to  
save the setting.  
-
"Wiper operation":  
● "Rear wiper operates in reverse: ON /  
OFF" (rear wiper coupled to reverse  
gear; refer to the "Visibility" section),  
* Depending on the country of sale.  
39  
Monitoring  
Access to the retractable screen  
Adjusting the angle of  
the screen  
If you have closed the screen, it will  
open again automatically:  
-
on switching on the audio and  
navigation system (unless it had  
been closed manually while the  
system was in operation),  
when an outgoing telephone call is  
made,  
-
-
-
when a voice command is given,  
when a warning message linked  
with the STOP warning lamp is  
displayed (PEUGEOT Connect  
Navigation (RT6)).  
The screen opens automatically when the  
ignition is switched on. It closes automatically  
three seconds after switching off the ignition if  
the audio and telematics system is switched off.  
You can adjust the angle of the screen to one of  
four defined positions, by repeated presses on  
the front or back of the control B. The position  
of the screen is memorised on closing.  
You can open or close the screen at any time,  
with the ignition on, using control A.  
-
-
Press button A: the screen folds.  
Press button A again: the screen opens  
again.  
40  
Monitoring  
1
Trip computer  
A few definitions  
Range  
Current fuel consumption  
Distance travelled  
(miles or km)  
(mpg or l/100 km or km/l)  
(miles or km)  
The distance which can still be  
Calculated over the last few seconds.  
Calculated since the last trip  
reset.  
travelled with the fuel remaining in the tank  
(related to the average fuel consumption over  
the last few miles (kilometres) travelled).  
This function is only displayed from  
20 mph (30 km/h).  
Stop & Start time counter  
(minutes / seconds or hours /  
minutes)  
This value may vary following a change  
in the style of driving or the relief,  
resulting in a significant change in the  
current fuel consumption.  
Average fuel  
consumption  
(mpg or l/100 km or km/l)  
Calculated since the last trip  
reset.  
If your vehicle is fitted with Stop &  
Start, a time counter calculates the time spent  
in STOP mode during a journey.  
It resets to zero every time the ignition is  
switched on with the key.  
When the range falls below 20 miles (30 km),  
dashes are displayed. After filling with at least  
5 litres of fuel, the range is recalculated and is  
displayed when it exceeds 60 miles (100 km).  
Average speed  
(mph or km/h)  
If dashes are displayed continuously  
while driving in place of the digits,  
contact a PEUGEOT dealer or a  
qualified workshop.  
Calculated since the last trip reset.  
41  
Monitoring  
Trip computer  
System that gives you information on the current journey (range, fuel consumption…).  
The trip computer provides the following  
information:  
F
The next press then returns you to the  
normal display.  
Monochrome screen A  
-
-
-
-
-
-
range,  
current fuel consumption,  
Stop & Start time counter,  
distance travelled,  
average fuel consumption,  
average speed.  
Trip reset  
Information displays  
F
Press the control for more than  
F
Press the button, located at the end of the  
wiper stalk, to display the various items of  
trip computer information in succession.  
two seconds to reset to zero the distance  
travelled, the average fuel consumption  
and the average speed.  
42  
Monitoring  
1
Trip computer  
System which provides instantaneous information on the current trip (range, fuel consumption…).  
Information displays  
Monochrome screen C  
With screen C  
With instrument panel screen  
F Press the button on the end of the wiper  
F
Press the PEUGEOT Connect Sound  
(RD5) "MODE" button repeatedly to  
display the trip comuter information.  
control stalk to display each of the trip  
computer tabs in turn.  
Instrument panel screen  
Then, repeatedly press the button on the end of  
the wiper control stalk to display each of the  
trip computer tabs in turn.  
Or  
F
Press the button on the end of the wiper  
control stalk to temporarily display a  
window with the trip computer information.  
Then, repeatedly press the button on the end of  
the wiper control stalk to display each of the  
trip computer tabs in turn.  
43  
Monitoring  
Trip reset  
Depending on your vehicle's equipment, the  
trip computer information appears in the  
monochrome C screen or in the instrument  
panel screen.  
-
The current information with:  
● the range,  
● the current fuel consumption,  
● the distance remaining to be travelled or  
the Stop & Start time counter.  
-
-
The trip "1" tab with:  
● the average speed,  
for the first trip,  
With the C screen or instrument panel  
screen  
● the average fuel consumption,  
F
When the trip required is displayed, press  
the control for more than two seconds.  
The trip "2" tab with:  
● the average speed,  
for the second trip,  
Trips "1" and "2" are independent but their use  
is identical.  
For example, trip "1" can be used for daily  
figures, and trip "2" for monthly figures.  
● the average fuel consumption,  
With the instrument panel screen  
-
-
A black screen  
A reminder of the navigation instructions  
with the PEUGEOT Connect Navigation  
(RT6) system.  
Press again to return to the current display.  
44  

Related Topics

Instrument panels
Indicator and warning lamps
Service indicator
Distance recorders
Screen A with audio equipment
Trip computer