Get Ease of use and comfort -> Front seats Guide for Peugeot 3008 SUV 2020

Ease of use and comfort

When driving

Manually-adjusted seats

5. Lumbar support adjustment

(only on the driver's seat)

Maintain a good driving position and hold the

steering wheel with both hands at the 'quarter to

three' position, so that you can easily and quickly

reach the controls behind and near the steering

wheel.

► Turn the knob forwards or backwards

to increase or decrease the level of lumbar

support.

‘AGR’ certiﬁed seats

Additional adjustments

Never adjust the seats or steering wheel

when driving.

Always keep your feet on the ﬂoor.

Front seats

Before moving the seat backwards,

ensure that there is no person or object

that might prevent the full travel of the seat.

There is a risk of trapping or pinching

passengers if present in the rear seats or of

jamming the seat if large objects are placed

on the ﬂoor behind the seat.

1. Longitudinal adjustment of the seat position

► Raise the control bar and slide the seat

forwards or backwards.

1. Seat cushion length adjustment

► Pull the handle forwards to release the

cushion, then move the front part of the seat

cushion forwards or backwards.

2. Seat cushion angle electric adjustment

► Press and hold the front or rear of the

button to raise or lower the front part of the

seat cushion.

► Release the bar to lock the seat in

position in one of the notches.

2. Seat cushion height adjustment

► Raise or lower the control as many times

as needed to obtain the desired height.

3. Seat backrest angle adjustment

► Turn the knob forwards or backwards to

recline the backrest to the desired angle.

► For a passenger seat that can be placed

in the table position, pull the handle and

guide the backrest forwards or backwards.

4. Head restraint height adjustment

Refer to the corresponding section.

Ease of use and comfort

Folding the backrest

Front head restraints

3. Lumbar support electric adjustment

The control allows independent adjustment of

the depth and vertical position of the lumbar

support.

Adjusting the height

► Press and hold the front or rear of the

control to increase or reduce the lumbar

support.

► Press and hold the top or bottom of the

control to raise or lower the lumbar support

area.

Placing the passenger seat

in the table position

► Pull the control fully upwards to release the

backrest.

The backrest of the passenger seat can be fully

folded forwards and secured in this position.

This function, when associated with folding

of the backrest of the rear seats, helps with

transporting long and bulky objects.

First steps:

► Tip the backrest fully forwards.

Upwards:

► Pull the head restraint up to the desired

position; you can feel the head restraint clicking

into position.

Downwards:

► Press lug A to lower the head restraint.

In this position, the backrest can support

a maximum load of 30 kg.

When sharp deceleration occurs, objects

placed on the folded backrest can turn into

projectiles.

► Lower the head restraint.

► Fold up the “aircraft” type table (depending

on version).

► Move the seat backwards to allow space for

the head restraint.

► Adjust the seat to the lowest position.

► Check that there is nothing that might

interfere with folding of the backrest (seat belt,

child seat, items of clothing, bags, etc.).

The head restraint is correctly adjusted

when its upper edge is level with the top

of the head.

Returning the backrest into position

► Pull the control fully upwards to release the

backrest.

► Raise the backrest and guide it backwards

until it latches into place.

► Check that the backrest is correctly latched

into place.

Removing a head restraint

► Pull the head restraint fully up.

► Press lug A to release the head restraint and

raise it fully.

Deactivation of the front passenger

airbag is recommended.

► Stow the head restraint securely.

Ease of use and comfort

Reﬁtting a head restraint

5. Lumbar support adjustment

► Insert the head restraint rods into the guides

in the corresponding seat backrest.

► Push the head restraint fully down.

► Press the lug A to release the head restraint

and push it down.

The control allows independent adjustment of

the depth and vertical position of the lumbar

support.

► Press and hold the front or rear of the

control to increase or reduce the lumbar

support.

► Adjust the height of the head restraint.

► Press and hold the top or bottom of the

control to raise or lower the lumbar support

area.

Never drive with the head restraints

removed; they should be in place and

adjusted for the occupant of the seat.

Memorising driving

positions

Associated with the electrically-adjusted driver’s

seat, this function allows two driving positions

to be memorised, to make these adjustments

easier if there are frequent driver changes.

It records the electric adjustments made to the

seat and door mirrors.

Electrically-adjusted driver's

seat

1. Seat cushion height and angle adjustment/

Longitudinal adjustment of the seat position

► Raise or lower the front of the control to

obtain the desired seat cushion angle.

► Raise or lower the rear of the control to

raise or lower the seat cushion.

► Slide the control forwards or backwards to

move the seat forwards or backwards.

2. Seat backrest angle adjustment

To carry out these electric adjustments,

switch on the ignition or start the engine

if the vehicle has gone into energy economy

mode.

These electric adjustments are accessible

about 1 minute after opening the driver's door.

They are deactivated about 1 minute after

switching the ignition oﬀ.

► Turn the control forwards or backwards to

recline the backrest to the desired angle.

3. Head restraint height adjustment

Refer to the corresponding section.

4. Seat cushion length adjustment

► Pull the handle forwards to release the

cushion, then move the front part of the seat

cushion forwards or backwards.

Using buttons M/1/2

Ease of use and comfort

► Enter the vehicle and switch the ignition on.

► Adjust your seat and the door mirrors.

► Press button M, then press button 1 or 2

within 4 seconds.

An audible signal conﬁrms the memorisation.

Memorising a new position cancels the previous

position.

Prolonged use of heated seats is not

recommended for people with sensitive

Heated seats

skin.

There is a risk of burns for people whose

perception of heat is impaired (e.g. illness,

taking medication).

To keep the heated pad intact and to prevent

a short circuit:

Recalling a stored position

– Do not place heavy or sharp objects on the

seat.

– Do not kneel or stand on the seat.

– Do not spill liquids onto the seat.

– Never use the heating function if the seat

is damp.

While the seat is moving, take care that

no person or object hinders the

automatic movement of the seat.

The function is active only with the engine

running.

► Press the button corresponding to the seat.

► Each press changes the heating level; the

corresponding number of indicator lamps come

on.

► To switch oﬀ the heating, press the button

until all of the indicator lamps are oﬀ.

The system status is memorised when the

ignition is switched oﬀ.

With the ignition on or engine running

► Press button 1 or 2 to recall the

corresponding position.

An audible signal sounds when adjustment is

complete.

You can interrupt the current movement by

pressing button M, 1 or 2 or by using one of the

seat adjustment controls.

A stored position cannot be recalled while

driving.

Multipoint massage

System with a choice of type of massage and

adjustment of its intensity.

This system operates with the engine running, as

well as in STOP mode of the Stop & Start.

The massage settings are adjusted via the touch

screen.

Do not use the function when the seat

is not occupied.

Reduce the heating intensity as soon as

possible.

When the seat and passenger compartment

have reached a satisfactory temperature,

switch the function oﬀ; reducing electrical

consumption in turn decreases energy

consumption.

From the front seat:

The recalling of stored positions is deactivated

45 seconds after switching oﬀ the ignition.

► Press this button; its green indicator

lamp comes on.

The settings page is displayed on the touch

screen with the last memorised settings.

If the settings suit you and you make no

changes, the display returns to its previous state,

and the function activates immediately.

Seats must be adjusted one after another,

starting with the driver's seat.

Ease of use and comfort

To modify the settings:

► Adjust the height and reach to suit your

driving position.

► Push the control to lock the steering wheel.

Adjustment

► Begin with the driver’s seat.

► Select a massage intensity from the three

levels oﬀered: "1" (Low), "2" (Normal) or "3"

(High).

► Select another type of massage from those

oﬀered.

For safety reasons, these adjustments

must only be carried out with the vehicle

stationary.

► Wait for the driver's seat settings page to

disappear.

► Next, proceed with the passenger's seat in

the same way.

Mirrors

The changes are applied immediately.

Once activated, the system starts a one hour

massage cycle, made up of sequences of 6

minutes of massage followed by 3 minutes at

rest.

Door mirrors

► Move control A to the right or to the left to

select the corresponding mirror.

► Move control B in any of the four directions

to adjust.

As a safety measure, the mirrors should

be adjusted to reduce the "blind spots".

The objects that you see in the mirrors are

in fact closer than they appear. Take this

into account in order to correctly judge the

distance of vehicles approaching from behind.

The system automatically stops at the end of the

cycle; the indicator lamp for the button goes oﬀ.

► Return control A to its central position.

Manual folding

Steering wheel

adjustment

The mirrors can be folded manually (parking

obstruction, narrow garage, etc.).

► Turn the mirror towards the vehicle.

Demisting/Defrosting

The demisting/defrosting of the door

mirrors works with the demisting/

defrosting of the rear screen.

Electric folding

For more information on Rear screen

demisting/defrosting, refer to the

corresponding section.

Depending on equipment, the door mirrors can

be folded electrically.

► From the inside, with the

ignition on, place control A in the

central position.

► When stationary, pull the control to release

the steering wheel.

► Pull control A backwards.

► Lock the vehicle from the outside.

Ease of use and comfort -> Front seats for Your Peugeot 3008 SUV 2020

Popular Manuals