Lighting and visibility -> Automatic wipers for Your Peugeot 3008 SUV 2020

Lighting and visibility  
Fast wiping (heavy rain)  
Off  
Windscreen wash  
4
► Pull the wiper control stalk towards you and  
hold.  
Normal wiping (moderate rain)  
Intermittent wiping  
Screenwash-wipe  
A final wiping cycle is performed when  
screenwashing ends.  
Intermittent wiping (proportional to the  
vehicle’s speed)  
The windscreen wash jets are  
incorporated into the tip of each wiper  
arm.  
Screenwash fluid is sprayed along the length  
of the wiper blade. This improves visibility and  
reduces screenwash fluid consumption.  
Switching off  
Reverse gear  
Automatic wiping  
When reverse gear is engaged, the rear wiper  
will come into operation automatically if the front  
windscreen wipers are operating.  
Refer to the corresponding section.  
The settings are changed via the Driving/  
Vehicle touch screen menu.  
Single wipe  
► Pull the stalk briefly towards you.  
To avoid damaging the wiper blades, do  
not operate the screenwash if the  
screenwash reservoir is empty.  
Only operate the screenwash if there is no  
risk of the fluid freezing on the windscreen  
and hindering visibility. During the winter  
period, use "very cold climate" rated products.  
Never top up with water.  
In the event of accumulation of snow or  
hard frost or if a bicycle carrier is fitted to  
a towing device, deactivate the automatic rear  
wiper via the vehicle configuration menu.  
In position 1 or 2, the wiping frequency is  
automatically reduced when the speed of  
the vehicle drops below 3 mph (5 km/h).  
When the speed is above 6 mph (10 km/h)  
again, the wiping frequency returns to the  
original frequency (fast or normal).  
Rear screenwash  
► Turn the ring all the way towards the  
dashboard and hold.  
The screenwash and the wiper operate for as  
long as the ring remains turned.  
A final wiping cycle is performed when  
screenwashing ends.  
Ha a gyújtást úgy vették le, hogy az  
ablaktörlők jártak, működtesse újra a kart  
a törlés ismételt bekapcsolásához, amint  
visszakapcsolta a gyújtást (kivéve, ha a  
gyújtás levétele egy percen belül történt).  
Rear wiper  
Automatic windscreen  
wipers  
In AUTO mode, the windscreen wipers work  
automatically and adapt to the intensity of the  
rain.  
After switching off the ignition, a slight  
movement of the windscreen wipers to  
store them under the bonnet may occur.  
Turn the ring to align the desired symbol with  
the marking.  
81  
Lighting and visibility  
The rainfall detection function uses a rain/  
sunshine sensor located at the top centre of the  
windscreen, behind the rear view mirror.  
This indicator lamp goes off in the  
instrument panel, accompanied by a  
message.  
Before removing a windscreen wiper blade  
Do not cover the rain/sunshine sensor.  
When using an automatic car wash,  
switch off the automatic wipers and the  
ignition.  
If the ignition has been off for more than  
one minute, the automatic wipers must  
be reactivated by pushing the control stalk  
downwards.  
In winter, wait until the windscreen is  
completely clear of ice before activating the  
automatic wipers.  
Malfunction  
If a fault occurs with the automatic wipers, the  
wipers operate in intermittent mode.  
Have it checked by a PEUGEOT dealer or a  
qualified workshop.  
Switching on  
Operating the wiper control stalk within one  
minute after switching off the ignition will place  
the wiper blades in a vertical position.  
► Proceed with the desired operation or the  
replacement of the wiper blades.  
Special position of the  
windscreen wipers  
This maintenance position is used while cleaning  
or replacing the wiper blades. It can also be  
useful, in wintry weather (ice, snow), to release  
the wiper blades from the windscreen.  
After refitting a windscreen wiper blade  
To return the wiper blades to their initial  
position after the operation, switch on the ignition  
and operate the wiper control stalk.  
► Give a short downwards push to the control  
stalk.  
A wiping cycle confirms that the instruction has  
been accepted.  
This indicator lamp lights up on the  
instrument panel, accompanied by a  
message.  
To maintain the effectiveness of the flat  
wiper blades, it is advisable to:  
– handle them with care.  
– clean them regularly using soapy water.  
– avoid using them to hold cardboard on the  
windscreen.  
– replace them at the first signs of wear.  
Switching off  
► Give the control stalk another brief push  
downwards or place the control stalk in another  
position (Int, 1 or 2).  
82