Practical information -> Roof bars for Your Peugeot 3008 SUV Third Generation (2024-2025)

Practical information  
► Remove the cap from the lock and press it  
onto the head of the key.  
► Release the wheel; it automatically locks in  
the unlocked position (position B).  
Maximum load distributed over the roof  
bars, for a loading height not exceeding  
40 cm: 70 kg.  
As this value may change, please verify the  
maximum load quoted in the guide supplied  
with the roof bars.  
7
If the height exceeds 40 cm, adapt the speed  
of the vehicle to the profile of the road to  
avoid damaging the roof bars and the fixings  
on the vehicle.  
Be sure to refer to national legislation in order  
to comply with the regulations for transporting  
objects that are longer than the vehicle.  
► Insert the key into the lock 7.  
► Open the lock using the key.  
► Replace the protective plug 2 into the  
carrier 1.  
Recommendations  
Distribute the load uniformly, taking care  
to avoid overloading one of the sides.  
Arrange the heaviest part of the load as close  
as possible to the roof.  
► Stow the towball in its bag to protect it from  
knocks and dirt.  
Roof bars  
Secure the load firmly.  
Drive gently: the vehicle will be more  
susceptible to the effects of side winds and its  
stability may be affected.  
Regularly check the security and tight  
fastening of the roof bars, at least before each  
trip.  
As a safety measure and to avoid  
damaging the roof, it is essential to use  
transverse roof bars approved for your  
vehicle.  
Observe the instructions on fitting and use  
contained in the guide supplied with the roof  
bars.  
Remove the roof bars once they are no longer  
needed.  
► Hold the towball 5 firmly in one hand; using  
the other hand, pull and turn the wheel 6 fully in  
a clockwise direction until it stops; do not release  
the wheel.  
► Extract the towball from the base of its  
carrier 1.  
Sunroof  
Check that the load does not protrude  
below the roof bars, so that it does not  
161  
Practical information  
impede movement of the sunroof - risk of  
major damage!  
The roof bar fixings have a stud which must be  
inserted into the opening of each anchorage  
point.  
Installation tips  
To t the snow chains during a journey, stop  
the vehicle on a flat surface at the side of the  
road.  
► Apply the parking brake and position any  
wheel chocks under the wheels to prevent  
movement of the vehicle.  
► Fit the snow chains following the instructions  
provided by the manufacturer.  
Fitting on longitudinal bars  
Snow chains  
In wintry conditions, snow chains improve  
traction as well as the behaviour of the vehicle  
when braking.  
Snow chains must be fitted only to the  
front wheels.  
They must never be fitted to "space-saver"  
type spare wheels.  
► Move off gently and drive for a few moments,  
without exceeding 31 mph (50 km/h).  
► Stop the vehicle and check that the snow  
chains are correctly tightened.  
The transverse bars must be fixed at the  
markings located on the longitudinal bars.  
It is strongly recommended that you  
practise fitting the snow chains on a level  
and dry surface before setting off.  
Observe the legislation in force in your  
country relating to the use of snow  
chains and maximum authorised speeds.  
Direct fitting on roof  
Avoid driving with snow chains on roads  
that have been cleared of snow to avoid  
damaging the vehicle's tyres and the road  
surface. If the vehicle is fitted with alloy  
wheels, check that no part of the chain or its  
fixings is in contact with the wheel rim.  
Only use chains that have been designed to be  
fitted on the type of wheel on the vehicle:  
Original tyre size  
215/65R16  
Maximum link size  
9 mm (Polaire XP9)  
9 mm (Polaire XP9)  
215/60R17  
215/55R18  
10 mm  
(Polaire 0112)  
Very cold climate screen  
(Depending on country of sale)  
This removable device prevents the  
accumulation of snow around the radiator  
cooling fan.  
For more information on snow chains, contact a  
PEUGEOT dealer or a qualified workshop.  
The transverse bars must only be fixed at the  
four anchorage points located on the roof frame.  
These points are concealed by the vehicle doors  
when the doors are closed.  
162