Restraint systems and airbags -> Seat belts for Your Skoda Kodiaq SUV 2020

42 Restraint systems and airbags › Seat belts  
Settings  
Restraint systems and airbags  
The activation or deactivation of the automatic fold-  
ing of the exterior mirrors, the synchronous adjust-  
ment of the mirror surfaces and the lowering of the  
passenger mirror surface when reversing takes place  
in the infotainment in the following menu.  
Seat belts  
Functionality  
Seat belts that are fastened correctly offer very  
good protection in the event of an accident. They re-  
duce the risk of an injury and increase the chance of  
survival in the event of a major accident.  
Or:  
WARNING  
The seat belts must not be removed or altered in  
any other way.  
Do not attempt to repair the seat belts yourself.  
Have a damaged seat belt replaced immediately by  
a specialist garage.  
Troubleshooting  
Electric mirror control disrupted  
Adjust the mirror surface by lightly pressing your  
finger.  
Automatic belt retractor  
The automatic retractor locks the belt in the event  
of a jerky pull on the belt. The belts lock, for example,  
when brakes are applied fully, when the car acceler-  
ates, when taking turns as well as when being close  
to a vehicle.  
CAUTION  
Risk of burns!  
Do not touch heated exterior mirror surfaces.  
WARNING  
If the seat belt does not lock when pulled jerkily,  
have the retractor checked by a specialist garage.  
Belt tensioners  
The safety for the driver, front passenger and the  
two passengers on the outer seats of the second  
row of seats who are wearing seat belts is en-  
hanced by the belt tensioners fitted to the inertia  
reels of the front seats and the outer seats of the  
second row of seats.  
If there is a collision with a certain severity, the seat  
belt is tightened by the belt tensioner so that unwan-  
ted body movement is prevented.  
The belt tensioner can also be deployed when the  
seat belt is not fastened.  
Belt tensioners are not activated in the event of a  
roll-over, minor collisions or in accidents in which no  
major forces are produced.  
Smoke is released when the belt tensioner is de-  
ployed. This does not indicate a vehicle fire.  
Reversible belt tensioner  
Vehicles with a proactive occupant protection sys-  
tem include reversible belt tensioners » page 186.  
The reversible belt tensioners increase safety for the  
belted driver and front passenger by automatically  
tightening the seat belt tightly over the body in criti-  
cal driving situations and then releasing it again.  
Status display in the instrument cluster display  
Depending on the display type, the display can be as  
follows.  
illuminated – unfastened front or rear seat belt  
Restraint systems and airbags › Seat belts 43  
Illuminates - unoccupied rear seat  
Slowly pull the webbing on the tongue B over  
chest and pelvis.  
illuminated – a rear seat belt is not fastened  
illuminated – a rear seat belt is not fastened  
illuminated – a rear seat belt is fastened.  
illuminated – a rear seat belt is fastened.  
illuminated – a rear seat belt is fastened.  
Insert lock tongue B into the second buckle until  
you hear it click into place.  
Carry out a tensile test to ensure that the lock  
tongues are securely engaged.  
To remove grab the tongue B and release by  
pressing the red button.  
Insert lock tongue A and release by pressing the  
red button.  
Hold the belt so it does not twist when rolling up.  
Settings  
service  
Move the seat belt  
Fastening the seat belt  
height adjuster up-  
wards to increase the  
height.  
Grasp the buckle latch  
and slowly pull the belt  
over the chest and pel-  
vis towards the buckle.  
Insert the buckle latch  
into the buckle until  
there is an audible  
click.  
Carry out a tensile test  
to determine whether  
the lock tongue is se-  
Press the safety button  
and move the seat belt  
height adjuster down  
to reduce the height.  
curely engaged.  
Unfastening the seat belt  
After adjustment, firm-  
ly pull on the belt to  
ensure that the seat  
belt height adjuster has  
correctly locked in  
place and that the belt  
is locked securely.  
Grab the lock tongue  
and release it by press-  
ing the red button.  
Hold the belt so it does  
not twist when rolling  
up.  
Troubleshooting  
Blocked automatic belt retractor  
Put on belt with two buckle latches and put down  
Grasp the strap in the  
middle and pull quickly  
in the direction of the  
arrow.  
Hold the strap and let  
it roll up slowly.  
Pull on the strap to see  
if the retractor is  
working properly.  
If the strap is still  
blocked, repeat the un-  
locking procedure once or twice.  
If the strap is still blocked, seek the help of a spe-  
cialist garage.  
To fasten the belt pull slowly on the tongue A .  
Insert lock tongue A into the buckle until you hear  
it click into place.