BEFORE DRIVING -> Windows for Your Suzuki Vitara SUV 2020

BEFORE DRIVING  
Type B  
Theft deterrent light  
(if equipped)  
Windows  
The keyless entry system, transmitter  
model T68L0 and controller model S54P0  
are in compliance with the essential  
requirements and other provisions of  
Directive 1999/5/EC.  
Manual window control  
(if equipped)  
EXAMPLE  
54P000211  
This light will blink with the ignition switch  
in “LOCK” or “ACC” position, or the ignition  
mode “LOCK” (OFF) or “ACC”. The blink-  
ing light is intended to deter theft by lead-  
ing others to believe that the vehicle is  
equipped with a security system.  
60G010A  
Raise or lower the door windows by turning  
the handle located on the door panel.  
NOTE:  
For the theft deterrent alarm system of  
European countries, Mexico and South  
Africa models, refer to “For European  
countries, Mexico and South Africa” in  
“SUPPLEMENT” section.  
2-16  
54P00-01E  
BEFORE DRIVING  
Driver’s side (Type B)  
EXAMPLE  
Passenger’s door  
EXAMPLE  
Electric window controls  
(if equipped)  
The electric windows can only be operated  
when the ignition switch is in “ON” position  
or the ignition mode is “ON”.  
(1)  
(3)  
Driver’s side (Type A)  
EXAMPLE  
(2)  
(5)  
(4)  
(1)  
54P000212  
54P000213  
The driver’s door has a switch (1) to oper-  
ate the driver’s window, and a switch (2) to  
operate the front passenger’s window or  
there are switches (3), (4), to operate the  
rear left and right passenger windows,  
respectively.  
The passenger’s door has a switch (5) to  
operate the passenger’s window.  
(2)  
54P000252  
2-17  
54P00-01E  
BEFORE DRIVING  
Lock switch (type A)  
EXAMPLE  
operating any of the switches (2), (3), (4)  
or (5). To restore normal operation, release  
the lock switch by pushing it again.  
CLOSE  
WARNING  
• You should always lock the pas-  
senger’s window operation when  
there are children in the vehicle.  
Children can be seriously injured if  
they get part of their body caught  
by the window during operation.  
• To avoid injuring an occupant by  
window entrapment, check that no  
part of the occupant’s body such as  
hands or head is in the path of the  
electric windows when closing  
them.  
• Always remove the ignition key or  
take the keyless push start system  
remote controller with you when  
leaving the vehicle even only for a  
short time. Also do not leave chil-  
dren alone in a parked vehicle.  
Unattended children could use the  
electric window switches and get  
trapped by the window.  
OPEN  
81A009  
54P000253  
To open a window, push the top part of the  
switch. To close the window, lift up the top  
part of the switch.  
Lock switch (type B)  
EXAMPLE  
The driver’s window has AUTO-DOWN  
and AUTO-UP features for greater conve-  
nience (at toll booths or drive-through  
restaurants, for example). This means the  
driver can open or close the window with-  
out holding the window switch in DOWN or  
UP position. Press down or lift up the  
driver’s window switch completely and  
release it. To stop the window before it  
reaches the FULL-DOWN or FULL-UP  
position, pull up or push down the switch  
briefly.  
NOTE:  
If you drive with one of the rear windows  
open, you may hear a loud sound caused  
by air vibration. To reduce the sound, open  
the driver’s or front passenger’s window, or  
narrow the rear window opening.  
54P000214  
The driver’s door also has a lock switch for  
the passenger’s window(s). When you  
push in the lock switch, the passenger’s  
window(s) cannot be raised or lowered by  
2-18  
54P00-01E  
BEFORE DRIVING  
To initialize the pinching prevention func-  
tion, use the following procedure:  
1) Turn the ignition switch to “ON” position  
or press the engine switch to change  
the ignition mode to “ON”.  
2) Open the driver’s window fully by hold-  
ing the window switch in DOWN posi-  
tion.  
3) Close the driver’s window by holding  
the switch in UP position, and keep  
holding the switch for 2 seconds after  
the window is fully closed.  
4) Check the driver’s window to see if the  
AUTO-DOWN/UP feature works.  
Pinching prevention function  
CAUTION  
The driver’s window is equipped with a  
pinching prevention function. This function  
detects a foreign object that is caught in  
the window as it is being closed by AUTO-  
UP feature, which allows you to close the  
window without holding the window switch  
in UP position, and stops the window from  
closing to prevent damage.  
• The pinching prevention function  
does not operate while you are  
holding the window switch in UP  
position.  
• The pinching prevention function  
may not detect an object caught in  
the window just before the window  
is fully closed.  
WARNING  
NOTE:  
To avoid injuring an occupant by win-  
dow entrapment, check that no part  
of the occupant’s body such as  
hands or head is in the path of the  
electric window when closing it.  
This function may not detect an  
object due to the size, hardness, or  
position of the object being caught in  
the closing window.  
Even if you cannot close the window by the  
AUTO-UP feature because there may be  
something wrong with the pinching preven-  
tion function, you can close the window by  
holding the window switch in UP position.  
If you drive in extreme off-road condition,  
the pinching prevention function may oper-  
ate accidentally because the window  
reacts to vehicle jolting.  
WARNING  
Whenever you disconnect and recon-  
nect the battery or replace the fuse,  
the pinching prevention function  
needs to be initialized.  
The pinching prevention function will  
not be activated until the initialization  
is completed.  
Pinching prevention function initializa-  
tion  
If the AUTO-DOWN/UP feature will not  
work after initialization, there might be  
something wrong with the pinching preven-  
tion function. Have your vehicle inspected  
by an authorized SUZUKI dealer.  
When you disconnect and reconnect the  
battery or replace the fuse, the function will  
be deactivated. In this condition, the  
AUTO-DOWN feature will be deactivated,  
while the AUTO-UP feature may remain  
activated. The pinching prevention function  
needs to be initialized.  
2-19  
54P00-01E