Interior features -> Other interior features-Other interior features for Your Toyota Corolla 4 Door 2023

277  
5-4. Other interior features  
5-4.Other interior features  
Rear (if equipped)  
Other interior features  
USB charging port (if  
equipped)  
The USB charging port are used  
to supply 3.0 A of electricity at 5  
V to external devices.  
The USB charging port are for  
charging only. They are not  
designed for data transfer or  
other purposes.  
Depending on the external  
device, it may not charge prop-  
erly. Refer to the manual  
The USB charging port can be  
used when  
The engine switch is in ACC or ON.  
Situations in which the USB  
charging port may not operate  
correctly  
included with the device before  
using a USB charging port.  
If a device which consumes more  
than 3.0 A at 5 V is connected  
If a device designed to communi-  
cate with a personal computer,  
such as a USB memory device, is  
connected  
Using the USB charging  
5
port  
Front  
If the connected external device is  
Lift the lid while pulling up the  
knob.  
turned off (depending on device)  
If the temperature inside the vehi-  
cle is high, such as after the vehi-  
cle has been parked in the sun  
About connected external  
device  
Depending on the connected exter-  
nal device, charging may occasion-  
ally be suspended and then start  
again. This is not a malfunction.  
NOTICE  
To prevent damage to the  
USB charging port  
Do not insert foreign objects into  
the port.  
Do not spill water or other liq-  
uids into the port.  
278  
5-4. Other interior features  
NOTICE  
The power outlet can be used  
when  
Do not apply excessive force to  
or impact the USB charging  
port.  
The engine switch is in ACC or ON.  
When turning the engine switch  
off  
Do not disassemble or modify  
the USB charging port.  
Disconnect electrical devices with  
charging functions, such as mobile  
battery packs.  
If such devices are left connected,  
the engine switch may not be turned  
off normally.  
To prevent damage to exter-  
nal devices  
Do not leave external devices in  
the vehicle. The temperature  
inside the vehicle may become  
high, resulting in damage to an  
external device.  
NOTICE  
To prevent the fuse from  
Do not push down on or apply  
unnecessary force to an exter-  
nal device or the cable of an  
external device while it is con-  
nected.  
being blown  
Do not use an accessory that  
uses more than 12 V 10 A.  
To avoid damaging the power  
outlet  
To prevent battery discharge  
Close the power outlet lid when  
the power outlet is not in use.  
Foreign objects or liquids that  
enter the power outlet may cause  
a short circuit.  
Do not use the USB charging port  
for a long period of time with the  
engine stopped.  
Power outlet  
To prevent the battery from  
being discharged  
The power outlet can be used  
for 12 V accessories that run on  
less than 10 A.  
Do not use the power outlet lon-  
ger than necessary when the  
engine is not running.  
Lift the lid while pulling up the  
knob and open the power outlet  
lid.  
Wireless charger (if  
equipped)  
A portable device, such as a  
smartphone or mobile battery,  
can be charged by just placing it  
on the charging area, provided  
the device is compatible with the  
Qi wireless charging standard  
created by the Wireless Power  
Consortium.  
The wireless charger cannot be  
used with a portable device that  
279  
5-4. Other interior features  
detected in the charge area, the  
charging coil inside the wireless  
charger will move toward it and  
start charging. If the charging coil  
inside a portable device moves  
outside of the charge area,  
charging will automatically stop.  
If 2 or more portable devices are  
placed on the charging tray, their  
charging coils may not be prop-  
erly detected and they may not  
be charged.  
is larger than the charging area.  
Additionally, depending on the  
portable device, the wireless  
charger may not operate prop-  
erly. Refer to the operation man-  
ual of the portable device.  
The “Qi” symbol  
The “Qi” symbol is a trademark  
of the Wireless Power Consor-  
tium.  
Using the wireless charger  
1 Press the power supply  
switch of the wireless char-  
ger.  
Name for all parts  
Pressing the switch again turns the  
wireless charger off.  
When turned on, the operation indi-  
cator light (green) comes on.  
When the engine switch is turned  
off, the on/off state of the wireless  
charger will be memorized.  
5
Power supply switch  
Operation indicator light  
Charge area*  
2 Place a portable device on  
the charging area with its  
charging surface facing  
down.  
Charging tray  
*
: Portable devices and wireless  
While charging, the operation indi-  
cator light (orange) will be illumi-  
nated.  
chargers contain charging coils.  
The charging coil in the wireless  
charger can be moved within the  
charge area near the center of  
the charging tray. If the charging  
coil inside a portable device is  
If charging does not begin, move  
the portable device as close to the  
center of the charging area as pos-  
sible.  
If charging is not performed, the  
280  
5-4. Other interior features  
operation indicator light will slowly  
illuminate in green and orange  
alternatively and a sound of  
Recharging function  
If a certain amount of time has  
elapsed since charging com-  
pleted and the portable device  
has not been moved, the  
wireless charger will restart  
charging.  
charging coil operation may be  
heard repeatedly. Depending on  
the portable device, its charging coil  
may not be in the center of the  
device. In this case, place the por-  
table device so that its charging coil  
is centered in the charging area.  
When charging is complete, the  
operation indicator light (green) will  
illuminate.  
If a portable device is moved  
significantly within the  
charging area, the charging  
coil may disconnect and  
charging may temporarily be  
stopped. However, if a  
charging coil is detected  
within the charging area, the  
charging coil inside the wire-  
less charger will move near  
the other coil and charging  
will resume.  
Operation indicator light status  
Operation indicator light  
Off  
State  
The Wireless charger is off  
Standby (charging is possible)  
Green (illuminated)  
*
Charging is complete  
A portable device has been placed on the  
charging area (identifying the portable  
device)  
Orange (illuminated)  
Charging in progress  
*
: Depending on the portable device, the operation indicator light may stay  
illuminated (orange) after charging has completed.  
If the operation indicator light blinks  
If an error is detected, the operation indicator light will blink (orange). Take  
the appropriate measures according to the table below.  
281  
5-4. Other interior features  
Operation indicator light Suspected cause Measure  
If the engine is running,  
stop and then restart the  
engine.  
If the engine switch is in  
ACC, start the engine.  
Blinks (orange) at a one  
second interval continu-  
ously  
Vehicle to charger com-  
munication failure.  
A foreign object exists  
between the portable  
device and charging  
area.  
Remove the foreign  
object.  
Blinks (orange) 3 times  
repeatedly  
If there is a case or  
cover attached to the  
portable device, remove  
it.  
Portable device is not  
positioned properly on  
the charging area.  
Stop charging, remove  
the portable device from  
the charging tray, wait  
for the temperature to  
drop, and then start  
charging again.  
The temperature of the  
wireless charger is  
excessively high.  
Blinks (orange) 4 times  
repeatedly  
5
certain genuine manufacture parts)  
and/or accessory attached, it may  
not be possible to charge the porta-  
ble device. If the portable device is  
placed on the charging area and  
does not charge, remove the cover  
and/or accessories.  
The wireless charger can be  
operated when  
The engine switch is in ACC or ON.  
Portable devices that can be  
charged  
Portable devices compatible with  
the Qi wireless charging standard  
can be charged by the wireless  
charger. However, compatibility  
with all devices which meet the Qi  
wireless charging standard is not  
guaranteed.  
If interference is heard in AM  
radio broadcasts while  
charging  
Turn off the wireless charger and  
check if the noise is reduced. If  
noise is reduced, press and hold the  
power supply switch of the wireless  
charger for 2 seconds. The fre-  
quency of the wireless charger is  
changed and noise may be  
reduced. When the frequency is  
changed, the operation indicator  
light will blink (orange) 2 times.  
The wireless charger is designed  
to supply low power electricity (5  
W or less) to a cellular phone,  
smartphone, or other portable  
device.  
If a cover or accessory is  
attached to the portable device  
Charging precautions  
Do not charge a portable device if a  
cover or accessory which is not Qi  
compatible is attached. Depending  
on the type of cover (including for  
If the electronic key cannot be  
detected in the cabin, charging  
cannot be performed. When a  
282  
5-4. Other interior features  
door is opened and closed,  
To prevent damage or burns  
charging may be temporarily sus-  
pended.  
Observe the following precau-  
tions.  
Failure to do so may result in a  
equipment failure and damage,  
catch fire, burns due to overheat  
or electric shock.  
While charging, the wireless char-  
ger and the portable device will  
become warm.  
This is not a malfunction.If a porta-  
ble device becomes warm while  
charging and charging stops due  
to the protection function of the  
portable device, wait until the por-  
table device cools down and  
charge it again.  
Do not insert any metallic  
objects between the charge  
area and the portable device  
while charging  
Do not attach an aluminum  
sticker or other metallic object to  
the charge area.  
Sound generated during opera-  
tion  
When the power supply switch is  
turned on or while a portable device  
is being identified, operation sounds  
may be heard. This is not a malfunc-  
tion.  
Do not attach an aluminum  
sticker or other metallic object to  
the side of the portable device  
(or to its case or cover) that  
touches the charge area.  
Cleaning the wireless charger  
P.291  
Do not use the charging tray as  
a small storage space.  
WARNING  
Do not subject to a strong force  
or impact.  
Caution while driving  
Do not disassemble, modify or  
When charging a portable device,  
for safety reasons, the driver  
should not operate the main part  
of the portable device while driv-  
ing.  
remove.  
Do not charge devices other  
than specified portable devices.  
Keep away from magnetic  
items.  
Caution while in motion  
Do not charge lightweight devices  
such as wireless headphones  
while in motion. These devices  
are very light and may be ejected  
from the charging tray, which may  
lead to unforeseen accidents.  
Do not charge devices if the  
charge area is covered in dust.  
Do not cover with a cloth or sim-  
ilar material.  
Caution regarding interfer-  
ence with electronic devices  
NOTICE  
People with implantable cardiac  
pacemakers, cardiac resynchroni-  
zation therapy pacemakers or  
implantable cardioverter defibrilla-  
tors, as well as any other electri-  
cal medical device, should consult  
their physician about the usage of  
the wireless charger.  
Situations in which the func-  
tion may not operate normally  
Devices may not be charged nor-  
mally in the following situations.  
The portable device is fully  
charged  
283  
5-4. Other interior features  
The portable device is being  
When the portable device is in  
contact with, or is covered by  
any of the following metallic  
objects:  
charged with a cable connected  
There is foreign matter between  
the charge area and portable  
device  
• A card that has metal on it, such  
as aluminum foil, etc.  
Charging has caused the porta-  
ble device to heat up  
• A pack of cigarettes that  
includes aluminum foil  
The temperature around the  
charging tray is 95°F (35°C) or  
higher, such as in extreme heat  
• A wallet or bag that is made of  
metal  
• Coins  
The portable device is placed  
with its charging side facing up  
• A heating pad  
The portable device is placed in  
an area misaligned from the  
charge area  
• CDs, DVDs or other media  
• A metal accessory  
• A case or cover made of metal  
The portable device is larger  
than the charging tray  
• A case which has magnet in it  
on the charging side of the por-  
table device.  
A foldable and portable device  
is placed outside the charge  
area  
5
Electric wave type wireless  
remote controls are being used  
nearby  
The camera lens protrudes 0.12  
in (3 mm) or more from the sur-  
face of the portable device  
NOTICE  
The vehicle is in an area where  
strong electrical waves or noise  
are emitted, such as near a tele-  
vision tower, power plant, gaso-  
line station, broadcasting  
station, large display, airport,  
etc.  
2 or more portable devices are  
placed on the charging tray at  
the same time  
If charging is abnormal or the  
operation indicator light contin-  
ues to flash for any other reason,  
the wireless charger may be mal-  
functioning. Contact your Toyota  
dealer.  
Any of the following objects that  
is 0.08 in (2 mm) or thicker is  
between the charging side of  
the portable device and the  
charge area  
• Thick cases or covers  
• A case or cover attached with  
an uneven or tilted surface, so  
that the charging side is not flat  
• Thick decorations  
• Accessories, such as finger  
rings, straps, etc.  
284  
5-4. Other interior features  
To prevent malfunctions and  
data corruptions  
Sun visors  
When charging, bringing a  
credit, or other magnetic card,  
or magnetic storage media  
close to the charge area may  
clear any stored data due to  
magnetic influence. Also, do not  
bring a wristwatch or other pre-  
cision instrument close to the  
charge area since doing so may  
cause it to malfunction.  
Do not charge with a non-con-  
tact IC card such as a transpor-  
tation system IC card inserted  
between the charging side of a  
portable device and the charge  
area. The IC chip may become  
extremely hot and damage the  
portable device or IC card. Be  
especially careful not to charge  
a portable device inside a case  
or cover with a non-contact IC  
card attached.  
1 To set the visor in the forward  
position, flip it down.  
2 To set the visor in the side  
position, flip down, unhook,  
and swing it to the side.  
3 To use the side extender,  
place the visor in the side  
position, then slide it back-  
ward. (if equipped)  
Do not leave portable devices  
inside the vehicle. The inside of  
the vehicle can become hot in  
extreme heat, which could  
cause a malfunction.  
Vanity mirrors  
Slide the cover to open.  
If the smartphone OS has  
been updated  
The vanity light turns on. (if  
equipped)  
If the smartphone OS has been  
updated to a newer version, its  
charging specifications may have  
changed significantly. For details,  
check the information on the man-  
ufacturer’s website.  
To prevent battery discharge  
Do not use the wireless charger  
for a long period of time with the  
engine stopped.  
To prevent battery discharge  
(vehicles with vanity lights)  
If the vanity lights remain on when  
the engine switch is OFF, the lights  
will go off automatically after 20 min-  
utes.  
285  
5-4. Other interior features  
WARNING  
NOTICE  
To prevent the battery from  
being discharged (vehicles  
with vanity lights)  
Assist grip  
Do not use the assist grip when  
getting in or out of the vehicle or  
rising from your seat.  
Do not leave the vanity lights on  
for extended periods while the  
engine is stopped.  
NOTICE  
To prevent damage to the  
assist grip  
Armrest (if equipped)  
Do not hang any heavy object or  
put a heavy load on the assist  
grip.  
Fold down the armrest for use.  
Coat hooks  
The coat hooks are provided  
with the rear assist grips.  
5
NOTICE  
To prevent damage to the  
armrest  
Do not apply too much load on the  
armrest.  
Assist grips  
WARNING  
Items that cannot be hung on  
An assist grip installed on the  
ceiling can be used to support  
your body while sitting on the  
seat.  
the coat hook  
Do not hang coat hangers or  
other hard or sharp objects on the  
hook. If the SRS curtain shield air-  
bags deploy, these items may  
become projectiles, causing death  
or serious injury.  
286  
5-4. Other interior features