Get Vehicle care -> Bulb replacement Guide for Vauxhall Grandland X SUV 2020

Vehicle care

219

Within one minute after switching off

ignition, operate the wiper lever to

position the wiper blades vertically on

the windscreen.

Lift the wiper arm until it stays in the

raised position, press button to

disengage the wiper blade and

remove.

Attach the wiper blade slightly angled

to the wiper arm and push until it

engages.

Bulb replacement

Switch off the ignition and switch off

the relevant switch or close the doors.

Only hold a new bulb at the base. Do

not touch the bulb glass with bare

hands.

Use only the same bulb type for

replacement.

Lower wiper arm carefully.

Attach the wiper blade slightly angled

to the wiper arm and push until it

engages.

Replace headlight bulbs from within

the engine compartment.

Lower wiper arm carefully.

Bulb check

Rear window

After a bulb replacement switch on

the ignition, operate and check the

lights.

Halogen headlights

Halogen headlights with separate

bulbs for low beam and high beam.

Lift wiper arm. Disengage wiper blade

as shown in illustration and remove.

220

Vehicle care

1. Remove the protective cover by

pulling.

3. Detach the bulb from the bulb

socket and replace the bulb.

4. Insert the bulb socket into the

reflector housing.

5. Fit the protective cover on.

Low beam (2)

High beam (1) inner bulb.

Low beam (2) outer bulb.

2. Press retaining clip downwards

and pull the bulb socket toward

the rear.

High beam (1)

1. Remove the protective cover by

pulling.

Vehicle care

221

4. Insert the bulb socket into the

reflector housing.

5. Fit the protective cover on.

Tail lights

Tail lights, daytime running lights and

3rd-brake light are designed as LEDs.

In case of failure, have LEDs replaced

by a workshop.

Front turn lights

In case of defective LEDs, have them

replaced by a workshop.

Light assembly in the body

Side light

In case of defective LEDs, have them

replaced by a workshop.

2. Press retaining clip upwards and

pull the bulb socket toward the

rear.

Daytime running light

In case of defective LEDs, have them

replaced by a workshop.

LED headlights

Headlights for low and high beam,

sidelights, daytime running lights and

turn lights are designed as LEDs and

cannot be changed.

1. Open the tailgate then unclip the

access cover on the relevant side.

Have lights repaired by a workshop in

case of failure.

Front fog lights

3. Detach the bulb from the bulb

socket and replace the bulb.

Have bulbs replaced by a workshop.

222

Vehicle care

2. Slacken the light fixing nut using a

box spanner or socket.

5. From the outside, carefully

withdraw the light assembly from

recess and remove. Take care

that the cable duct remains in

position.

6. Turn the bulb socket

anticlockwise and remove it from

the light assembly.

7. Detach the bulb from the bulb

socket and replace the bulb.

To avoid losing the nut if it drops

into the wing trim, first place a

cloth below it.

3. Manually unscrew and remove

the light fixing nut.

4. Disengage the retaining clip,

while pushing the light out slightly.

Brake light(1)

Vehicle care

223

2. Slacken the light fixing nut using a

box spanner or socket.

Light assembly in the tailgate

3. Manually unscrew and remove

the light fixing nut.

4. Disengage the retaining clip,

while pushing the light assembly

out slightly.

5. From the outside, carefully

withdraw light assembly from

recess and remove. Take care

that the cable duct remains in

position.

Turn light (2)

8. Insert the bulb socket into the light

assembly. Fit the light assembly in

the recess and tighten the light

fixing nut from the inside. Attach

the cover.

1. Open the tailgate and remove the

cover.

6. Turn the bulb socket

anticlockwise and remove it from

the light assembly.

224

Vehicle care

7. Detach the bulb from the bulb

socket and replace the bulb:

Rear fog light (2)

Side turn lights

8. Insert the bulb socket into the light

assembly. Fit the light assembly in

the recess and tighten the light

fixing nut from the inside. Attach

the cover.

To replace bulb, remove light

assembly:

3rd-brake light

The 3rd-brake light is designed as

LED and can not be changed.

Have lights repaired by a workshop in

case of failure.

Bulb check

Reverse light (1)

Switch on the ignition, operate and

check all lights.

1. Slide the light assembly forward

and remove it at the back.

Vehicle care

225

4. Insert bulb socket and turn

anticlockwise.

Electrical system

5. Insert left end of the light

assembly, slide to the left and

insert right end.

Fuses

Data on the replacement fuse must

match the data on the defective fuse.

There are two fuse boxes in the

Number plate light

vehicle:

Number plate lights are designed as

LEDs and can not be changed.

●

engine compartment

instrument panel

Have lights repaired by a workshop in

case of failure.

Before replacing a fuse, turn off the

respective switch and the ignition.

2. Turn bulb socket clockwise and

remove from light assembly.

A blown fuse can be recognised by its

melted wire.

Interior lights

Have the following bulbs replaced by

a workshop:

Caution

●

courtesy light, reading lights

load compartment light

instrument panel illumination

Do not replace the fuse until the

cause of the fault has been

remedied.

Some functions are protected by

several fuses.

Fuses may also be inserted without

existence of a function.

3. Detach the bulb from the bulb

socket and replace the bulb.

Vehicle care -> Bulb replacement for Your Vauxhall Grandland X SUV 2020

Popular Manuals