Get Starting and driving -> HomeLink Guide for Volvo XC60 SUV 2020

STARTING AND DRIVING

HomeLink^®is delivered integrated in the rear-

view mirror. The HomeLink^®panel consists of

three programmable buttons and an indicator

light in the mirror.

HomeLink^®*²³

WARNING

HomeLink^®24is a programmable remote con-

trol, integrated in the vehicle electrical sys-

tem, that can control up to three different

devices (e.g. garage door opener, alarm sys-

tem, outdoor and indoor lighting) and thereby

replace the remote controls for these.

No person or object should be behind the

tow truck when the vehicle is lifted onto

the bed of the truck.

For more information about HomeLink^®,

please visit: www.HomeLink.com or call

1-800-355-3515.

CAUTION

The towing eyelet is only intended for tow-

ing on roads, and must not be used to pull

vehicles from ditches or any similar pur-

pose involving severe strain. Call a tow

truck for professional assistance.

Save the original remote controls for future

programming (e.g. for use in another vehicle).

It is also advisable to delete the button pro-

gramming if the vehicle is sold.

General

Related information

•

Using HomeLink^®* (p. 445)

Programming HomeLink^®* (p. 443)

Type approval for HomeLink^®* (p. 445)

CAUTION

Note that the vehicle must always be

towed with the wheels rolling forward.

Related information

Attaching and removing the towing eyelet

(p. 439)

•

The illustration is generic – the design may vary.

Button 1

Button 2

Button 3

Indicator light

Certain markets only.

HomeLink and the HomeLink house symbol are registered trademarks of Gentex Corporation.

442

* Option/accessory.

STARTING AND DRIVING

Programming HomeLink^®*²⁵

Follow these instructions to program

HomeLink^®, reset all programming, or pro-

gram individual buttons.

1. Point the remote control at the

HomeLink^®button to be programmed and

hold it about 2-8 cm (1-3 inches) from the

button. Do not obstruct the HomeLink^®

indicator light.

3. Do not release the buttons until the indica-

tor light has stopped flashing slowly

(about once a second) and either flashes

quickly (about 10 times a second) or

glows steadily.

NOTE

> If the indicator light glows steadily:

Indication that programming is com-

plete. Press the programmed button

twice to activate.

Note: Some remote controls are more

effective at programming HomeLink^®from

a distance of about 15-20 cm (6-12

inches). Keep this in mind if you experi-

ence any programming difficulties.

In some vehicles, the ignition must be on

or in the "accessory position" before

HomeLink^®can be programmed or used. It

can be a good idea to put new batteries in

the remote control being replaced by

HomeLink^®for faster programming and

better radio signal transmission. The

HomeLink^®buttons should be reset before

programming.

If the indicator light flashes quickly:

The device being programmed with

HomeLink^®may have a security func-

tion that requires an extra step. Try

pressing the programmed button twice

to see whether the programming

works. Otherwise, continue with the

following steps.

2. Press and hold both the remote control

button and the HomeLink^®button to be

programmed.

WARNING

While HomeLink^®is being programmed,

the garage door or gate being programmed

may be activated. Make sure that no one is

near the door or gate during programming.

When programming a garage door opener,

it is advised to park outside of the garage.

Certain markets only.

}}

* Option/accessory. 443

STARTING AND DRIVING

www.HomeLink.com, or call

1–800–355–3515.

Related information

•

Using HomeLink^®* (p. 445)

HomeLink^®* (p. 442)

Programming individual buttons

To program an individual HomeLink^®button:

Type approval for HomeLink^®* (p. 445)

1. Press and hold the desired button for

about 20 seconds.

When the indicator light on HomeLink^®

starts flashing slowly, it is possible to pro-

gram as usual.

4. Locate the "training" button²⁶on the

receiver for the e.g. garage door opener. It

is usually located near the antenna bracket

on the receiver.

Note: If the button you are reprogram-

ming does not program with a new

device, it will return to the previously

saved programming.

5. Press and release the "training" button

once. Programming must be completed

within 30 seconds after pressing the but-

ton.

Resetting the HomeLink^®buttons

It is only possible to reset all HomeLink^®but-

tons at once. It is not possible to reset individ-

ual buttons. Individual buttons can only be

reprogrammed.

Press and release the HomeLink^®button

to be programmed. Repeat the press/

hold/release sequence a second time. For

some receivers, the sequence may need to

be repeated a third time.

–

Press and hold the outer buttons (1 and 3)

on HomeLink^®for about 10 seconds.

> When the indicator light goes from a

steady glow to flashing, the buttons

have been reset and are ready for

reprogramming.

> Programming is now completed and

the garage door, gate, etc. should now

be activated when the programmed

button is pressed.

If you experience any difficulties programming,

please contact HomeLink^®at:

The name and color of the button varies depending on the manufacturer.

444

* Option/accessory.

STARTING AND DRIVING

Using HomeLink^®*²⁷

Type approval for HomeLink^®*²⁸

WARNING

Once HomeLink^®is programmed, it can be

used instead of the separate remote controls.

Press and hold the programming button. The

garage door, gate, alarm system, etc. will be

activated (this may take several seconds). If

the button is held down for more than 20 sec-

onds, reprogramming will begin. The indicator

light will glow steadily or flash when the but-

ton has been pressed. The original remote

controls may be used concurrently with

HomeLink^®if desired.

•

If you use HomeLink^®to open a garage

door or gate, be sure no one is near the

gate or door while it is in motion.

FCC (USA) and IC (Canada)

This device complies with FCC rules part 15

and Industry Canada RSS-210. Operation is

subject to the following two conditions: (1)

This device may not cause harmful interfer-

ence, and (2) This device must accept any

interference that may be received including

interference that may cause undesired opera-

tion.

Do not use HomeLink^®with any

garage door opener that lacks safety

stop and reverse features as required

by US federal safety standards (this

includes any garage door opener model

manufactured before April 1, 1982). A

garage door that cannot detect an

object - signaling the door to stop and

reverse - does not meet current U.S.

federal safety standards. For more

information, contact HomeLink at:

www.homelink.com.

WARNING

The transmitter has been tested and com-

plies with FCC and IC rules. Changes or

modifications not expressly approved by

the party responsible for compliance could

void the user's authority to operate the

device.²⁹

NOTE

When the ignition is switched off,

HomeLink^®will be active for at least

7 minutes.

Related information

•

HomeLink^®* (p. 442)

Programming HomeLink^®* (p. 443)

Type approval for HomeLink^®* (p. 445)

NOTE

Type approval for EU

HomeLink^®cannot be used if the vehicle is

locked and the alarm is armed* from the

outside.

Gentex Corporation hereby declares that

HomeLink^®Model UAHL5 complies with the

Radio equipment directive 2014/53/EU.

Wavelengths within which the radio equip-

ment operates:

433.05MHz-434.79MHz <10mW E.R.P.

868.00MHz-868.60MHz <25mW E.R.P.

•

Certain markets only.

The term "IC:" before the certification/registration number only signifies that Industry Canada technical specifications were met.

}}

* Option/accessory. 445

STARTING AND DRIVING

868.70MHz-868.20MHz <25mW E.R.P.

869.40MHz-869.65MHz <25mW E.R.P.

869.70MHz-870.00MHz <25mW E.R.P.

•

Activating and deactivating the

Compass*

An integrated compass³⁰in the upper right

corner of the rearview mirror shows the

direction the vehicle is traveling.

compass*

An integrated compass³¹in the upper right

corner of the rearview mirror shows the

direction the vehicle is traveling.

Certificate holder address: Gentex Corpora-

tion, 600 North Centennial Street, Zeeland MI

49464, USA

The compass is automatically activated when

the vehicle is started.

For further details, search for support informa-

tion on type approval at www.volvocars.com.

To deactivate/activate the compass manually:

–

Use a paper clip or similar object to press

the button on the bottom of the mirror.

Related information

•

HomeLink^®* (p. 442)

> If the compass is deactivated when the

vehicle is switched off, it will not be

activated the next time the vehicle is

started. The compass will then need to

be activated manually.

Rearview mirror with compass.

Related information

Eight different compass directions are shown

with the abbreviations: N (north), NE (north-

east), E (east), SE (southeast), S (south), SW

(southwest), W (west) and NW (northwest).

Compass * (p. 446)

•

Calibrating the compass* (p. 447)

•

Related information

Activating and deactivating the compass *

•

(p. 446)

Calibrating the compass* (p. 447)

•

Rearview mirror with compass is available as an option only on certain markets and models.

446

* Option/accessory.

Starting and driving -> HomeLink for Your Volvo XC60 SUV 2020

Popular Manuals