Tires and wheels -> Wheel trim for Your Volkswagen Golf 4 Door 2023

WARNING  
Hubcaps  
The temperature grade for this tire  
is established for a tire that is prop-  
erly inflated and not overloaded.  
Excessive speed, underinflation or  
or in combination, can cause heat  
buildup and possible tire failure.  
Please read the introductory information and  
heed the Warnings and Notice  
298.  
and on page  
Wheel trim  
Introduction  
WARNING  
Unsuitable wheel covers and improper installation  
of wheel covers can cause accidents and severe in-  
juries.  
Fig. 181 Pulling the hubcap off.  
Improperly installed wheel covers can come  
loose while driving and endanger other moto-  
rists and cyclists.  
·
Do not use damaged wheel covers.  
·
·
Always make sure that the flow of air for brake  
system cooling is not blocked or reduced before  
installing wheel covers. This applies to both fac-  
tory-installed wheel covers and aftermarket  
wheel covers. Insufficient air supply may signifi-  
cantly increase stopping distance.  
NOTICE  
To help prevent damage to the vehicle, be careful  
when removing wheel covers and be sure to install  
them properly.  
Fig. 182 Twisting the hubcap off.  
The hubcaps are designed to protect the wheel bolts  
and should be installed again after a wheel change.  
Depending on the vehicle model, the hubcaps can  
either be pulled off → fig. 181 or removed by twist-  
ing → fig. 182.  
To remove: Take the wire clip out of vehicle tool  
kit and hook it into one of the holes in the hubcap  
fig. 181.  
— Pull the hubcap off in the direction of the arrow.  
To install: Press the hubcap against the rim until it  
298  
Tires and wheels  
     
Vehicles with twist-off hubcaps  
Wheel bolt caps  
To remove: Twist the hubcap to the left or right  
until it loosens from the wheel rim → fig. 182.  
Please read the introductory information and  
heed the Warnings and Notice  
298.  
and on page  
— Grasp behind one of the lugs and pull the hubcap  
off.  
rim.  
Wheel covers  
Please read the introductory information and  
heed the Warnings and Notice  
298.  
and on page  
Fig. 184 Pulling cover caps off wheel bolts.  
— Take the wire clip out of the vehicle tool kit  
→ page 227, Vehicle tool kit.  
— Insert the wire clip through the opening of the  
cover cap → fig. 184 and pull off in the direction  
of the arrow.  
change.  
The anti-theft wheel bolt (if equipped) has a sepa-  
rate cap. This only fits the anti-theft wheel bolt, but  
not the standard wheel bolts.  
Fig. 183 Pulling the wheel cover off.  
Pulling off the wheel cover  
— Take the lug wrench (if equipped) and wire clip  
out of the vehicle tool kit → page 227, Vehicle  
tool kit.  
Changing a wheel  
— Place the wire clip hook in one of the openings of  
the wheel cover.  
Introduction  
— Slide the lug wrench through the clip → fig. 183  
and pull the wheel cover off in the direction of  
the arrow.  
Change a wheel by yourself only if the vehicle is  
parked in a safe location, you are familiar with safety  
procedures and the technical steps, and you have  
proper tools available. Otherwise, get expert assis-  
tance.  
Installing the wheel cover  
— Screw the anti-theft wheel bolt (if equipped) into  
position → fig. 186 2 or 3 in relation to the po-  
sition of the tire valve. Otherwise, the wheel cov-  
er cannot be installed.  
The vehicle jack can only be safely used to change  
the wheel on a vehicle that has only one flat or dam-  
aged tire. If the vehicle does not have the support it  
needs from 3 fully inflated tires, the vehicle can fall  
off the jack. If more than 1 tire on the vehicle is flat  
or damaged, do not lift the vehicle with the vehicle  
jack. Instead, get expert assistance.  
— Align the valve cutout with the valve  
fig. 186 1 , and press the wheel cover onto the  
wheel rim.  
Make sure that the wheel cover is latched onto the  
rim along the entire circumference.  
Changing a wheel  
299