Get Lights Guide for Volkswagen Tiguan 4 Door 2023

Lights

Headlights

Switching the turn signals on and off

Fig. 100 On the left side of the steering column: turn signal and high beam lever.

Right turn signal

Left turn signal

Switching the turn signals on and off

1. Switch the ignition on.

2. Move the turn signal and high beam lever from the center position to the preferred position ﬁg. 100.

3. To cancel the turn signal, move the turn signal and headlamp lever back to its basic position.

If no chime sounds when the turn signal is on, contact suitably qualiﬁed professionals and have the vehicle checked. Volkswagen recommends contacting an

authorized Volkswagen dealer or authorized Volkswagen Service Facility.

3-blink turn signal

To use the 3-blink turn signal, move the turn signal and high beam lever upward or downward to the pressure point and then release the lever. The turn signal will

blink three times.

To stop the 3-blink turn signal before it ends, move the turn signal and high beam lever immediately to the pressure point in the opposite direction and release.

The 3-blink turn signal can be activated and deactivated in the vehicle settings in the Infotainment system ⇒ Vehicle settings menu.

WARNING

Using the turn signals incorrectly, not using the turn signals, or forgetting to turn the turn signal off can mislead other road users. This can cause accidents and

serious or fatal injuries.

Always activate the turn signals correctly when changing lanes, passing, or turning.

Switch the turn signal off again every time you ﬁnish changing lanes, passing, or turning.

The emergency flashers also work when the ignition is switched off ⇒ In case of an emergency.

Switching the lights on and off

123

Fig. 101 Next to the steering wheel: light switch (one version).

Switching the lights on

1. Switch the ignition on.

2. Turn the light switch to the desired position ﬁg. 101:

The side lights or parking lights and daytime running lights are switched on.

Automatic headlight control: the headlights will switch on or off depending on the brightness and weather conditions

⇒

, ⇒ Automatic headlight

control .

The side lights or parking lights and daytime running lights are switched on. The green symbol in the light switch turns on.

The low beam headlights are switched on.

Switching the lights off

1. Switch the ignition off.

2. Turn the light switch to the desired position:

The lights are switched off.

The orientation lighting can be switched on ⇒ “Exit lighting” and “Entry lighting” function (orientation lighting) .

The parking light is switched on ⇒ Parking lights. The green symbol in the light switch turns on.

The low beam headlights are switched off.

Vehicles with ignition switch: As long as the remote control vehicle key is in the ignition switch, the parking light continues to light up.

Vehicles with starter button: As long as the driver door is closed, the parking light continues to light up.

Daytime running lights

The optional daytime running lights can increase the visibility of your vehicle in trafﬁc during the daytime.

The daytime running light turns on automatically every time the ignition is switched on if the light switch is in the

The daytime running lights cannot be switched on or off manually.

position (if brightness detected).

Daytime running lights parking function

Depending on the equipment, the vehicle may have a daytime running lights parking function to turn off the daytime running lights temporarily when the ignition is

switched on.

Switch off the daytime running lights:

1. Switch the ignition on.

2. Turn the light switch to the position.

3. Set the electronic parking brake.

Switch on the daytime running lights:

1. Switch off the electronic parking brake.

WARNING

If the vehicle lighting is not used appropriately for the weather conditions, the road will not be illuminated sufﬁciently. The vehicle will not be visible to other road

users or will be difﬁcult to see. This can cause accidents and serious or fatal injuries.

Always turn on the low beam headlight in the dark, when it is raining, and when visibility is poor.

124

Regularly check that the lighting system and turn signals are functioning correctly.

WARNING

The parking lights or daytime running lights are not bright enough to illuminate the road sufﬁciently and to be seen by other road users. The taillights do not

switch on with the daytime running lights. Without its taillights turned on, the vehicle may not be seen by other road users in the dark, in the fog, and when

visibility is poor. This can cause accidents and serious or fatal injuries.

Always turn on the low beam headlight in the dark, when it is raining, and when visibility is poor.

WARNING

The automatic headlights

only turns the low beam headlights on and off when there are changes in brightness. Insufﬁcient lighting on the road may cause accidents and serious or

fatal injuries.

are for assistance only. The driver is always responsible for turning on the correct vehicle lighting. Automatic headlight control

Turn on the low beam headlights manually in certain weather conditions, such as in fog.

When reverse gear is engaged, the cornering lights on both sides of the vehicle will turn on automatically to better illuminate the surroundings while

maneuvering.

Switching the high beam headlights on and off

Fig. 102 On the left side of the steering column: turn signal and high beam lever.

turn on the high beam headlight.

Activate the headlight flashers or turn off the high beam headlights.

If the high beam headlights or headlight ﬂashers are turned on, the blue

indicator light or

will come on in the instrument cluster ⇒

Turning on the high beam headlight

1. Switch the ignition on.

2. Switch on the low beam headlight.

3. Press the turn signal and high beam lever forward out of the center position ﬁg. 102.

Turning off the high beam headlight

1. Pull the turn signal and high beam lever backward out of the center position ﬁg. 102.

Turning the headlight ﬂasher on and off

1. Pull the turn signal and high beam lever backward out of the center position and hold it ﬁg. 102.

Release the turn signal and high beam lever to turn the headlight ﬂasher off.

Light Assist

Depending on the equipment, high beam control (Light Assist) may be available → page , High Beam Control (Light Assist) .

WARNING

Incorrect use of the high beam headlight may distract and blind other road users. This can cause accidents and serious or fatal injuries.

Use the high beam headlights only if other road users cannot be distracted or blinded.

125

High Beam Control (Light Assist)

High beam control (Light Assist) switches off automatically if the system detects oncoming vehicles or vehicles driving ahead. In addition, Light Assist generally

detects well-lit areas such as towns and deactivates the high beam headlights when driving through these areas.

The high beam headlights switch on and off automatically within the limits of the system, depending on the environmental and trafﬁc conditions and the vehicle

speed ⇒

Switching on high beam control (Light Assist)

1. Switch on the ignition and the automatic headlights

2. Tap the turn signal and high beam lever forward out of the basic position.

When Light Assist is switched on, the

indicator light in the instrument cluster display will turn on. When high beam control (Light Assist) is active, the blue

indicator light

for the high beam headlight in the instrument cluster lights up.

Adjusting the sensitivity of Light Assist

Depending on the country, the sensitivity of Light Assist can be set in two stages:

Increasing the sensitivity: press the turn signal and high beam lever forwards from its original position and hold it in this position for around 15 seconds.

The

indicator light on the instrument cluster will blink three times to conﬁrm that this has been applied.

Setting the sensitivity back to its standard setting: press the turn signal and high beam lever forwards from its original position and hold it in this position for

around 15 seconds.

The

indicator light on the instrument cluster will blink three times in quick succession to conﬁrm that this has been applied.

Or: Switch the ignition off and on.

Switching off high beam control (Light Assist)

1. Switch off

automatic headlights.

Or: when Light Assist is switched on and active, pull the turn signal and high beam lever backward.

Or: if high beam control (Light Assist)is switched on and not active, tap the turn signal and high beam lever forward. The manual high beam headlights are now

switched on. Pull the turn signal and high beam lever backwards to switch the high beam headlights off manually if necessary.

Or: Switch off the ignition.

System limitations

The high beams must be switched off manually in the following situations, because Light Assist may not switch them off at the right time or at all:

In poorly lit towns which cannot be recognized as a town by the system.

On poorly lit roads with strongly reﬂective signs.

If there are others on the road who have inadequate lighting, such as pedestrians or cyclists.

On tight curves where the view of trafﬁc is partially obstructed, on steep rises, or in dips.

When there are oncoming vehicles on roads with a center barrier and the drivers in the oncoming vehicle can clearly see above the barrier, for example truck

drivers.

In fog, snow, and heavy rain.

When there are dust and sand in the air.

If the windshield is damaged in the camera's ﬁeld of vision.

If the camera visual ﬁeld is fogged over, dirty, or covered by a sticker, snow, or ice.

If the camera switches off automatically due to a high ambient temperature or exposure to direct sunlight for a prolonged period. Light Assist will be available

once the camera is available again.

If the camera is faulty and the power supply is interrupted.

WARNING

Light Assist may not detect all trafﬁc situations correctly and the function may be restricted in certain situations. High beam control (Light Assist) is only an aid.

The driver is always responsible for turning on the correct vehicle lighting. Switching on the high beam headlight at the wrong time may distract and blind other

road users. This can cause accidents and serious or fatal injuries.

Always control the headlights yourself and adapt them to the lighting, visual, and trafﬁc conditions.

Switch the high beam off manually if it could blind other road users.

WARNING

126

If the camera lens is dirty, covered, or damaged, the Light Assist function may be limited. This is also the case if the vehicle lighting system is changed, such as

by adding auxiliary headlights. This can cause accidents and serious or fatal injuries.

Regularly clean the camera view area and keep it free of snow and ice.

Do not cover the camera view area.

Regularly check the windshield for damage in the camera lens area.

Dynamic cornering light

The dynamic cornering lights provide optimum illumination of the roadway.

The dynamic cornering light only works when the automatic headlights

6 mph).

are switched on and at speeds of more than approximately 10 km/h (approximately

Switching the poor weather lights on and off

Poor weather lights help you to illuminate the carriageway more effectively when visibility is poor.

The poor weather light can be switched on when the ignition is switched on and the automatic headlights

or dipped beams

are switched on.

Switching on the Poor Weather Lights

1. Switch the ignition on.

2. Automatic headlights

3. Pull out the light switch up to the ﬁrst retainer.

The green indicator light in the light switch will turn on.

or dipped beams

switched on.

Switching off the Poor Weather Lights

1. Push in the light switch or turn it to the

position.

If the poor weather light is switched on when the automatic headlights are switched on

ambient light level.

, the dipped beams are also switched on, regardless of the

Troubleshooting

Turn signal indicator light

The green indicator light blinks.

If a turn signal light on the vehicle is not working, the indicator light will blink twice as fast.

1. Check the lights and replace any bulbs as necessary ⇒

Introduction.

2. If the malfunction persists, contact a suitably qualiﬁed professional. Volkswagen recommends contacting an authorized Volkswagen dealer or authorized

Volkswagen Service Facility.

Trailer turn signal indicator light

The green indicator light blinks.

If a trailer turn signal or the entire trailer light system is out, the indicator light will turn off.

1. Check the lights and replace any bulbs as necessary ⇒

Introduction.

2. If the malfunction persists, contact a suitably qualiﬁed professional. Volkswagen recommends contacting an authorized Volkswagen dealer or authorized

Volkswagen Service Facility.

Exterior lighting malfunction

The yellow indicator light turns on.

The headlights have completely or partially failed.

1. Check the lights and replace any bulbs as necessary ⇒

Introduction.

2. If the malfunction persists, contact a suitably qualiﬁed professional. Volkswagen recommends contacting an authorized Volkswagen dealer or authorized

Volkswagen Service Facility.

Rain/light sensor malfunction

The yellow indicator light turns on.

In the

light switch position, the vehicle lighting will not turn on or off automatically.

1. Switch the ignition off and on.

127

2. If the malfunction persists, contact a suitably qualiﬁed professional. Volkswagen recommends contacting an authorized Volkswagen dealer or authorized

Volkswagen Service Facility.

Dynamic cornering light

When travel mode is activated, the dynamic cornering light does not work.

The swivel behavior of the bulbs can be inﬂuenced by the selected driving mode.

If the dynamic cornering light malfunctions, this is indicated on the instrument cluster display. Contact a suitably qualiﬁed professional. Volkswagen recommends

contacting an authorized Volkswagen dealer or authorized Volkswagen Service Facility.

Parking lights

If the

parking light function is switched on, both headlights will come on, along with the parking lights, sections of the taillights, the license plate light and variou

buttons in the vehicle interior.

Automatic parking light deactivation

The vehicle detects that the 12 V vehicle battery is low and switches off the parking light early enough to ensure that the engine can still be started, but not until at

least two hours have passed.

If the battery capacity is not sufﬁcient for the parking light to run for two hours, the 12 V vehicle battery may drain to such an extent that the engine can no longer be

started.

WARNING

If the vehicle is stopped without enough lighting and cannot be seen or is difﬁcult for others on the road to see, this can cause accidents and serious or fatal

injuries.

Always stop the vehicle safely and with enough lighting.

Follow the country-speciﬁc legal regulations.

“Exit lighting” and “Entry lighting” function (orientation lighting)

When you are entering and exiting the vehicle in the dark, the “Exit lighting” and “Entry lighting” function illuminates the immediate area around the vehicle.

Depending on the equipment, the vehicle can have an automatic or manual “Coming home” function:

Automatic “Coming home” function: the “Coming home” and “Leaving home” function automatically control the rain/light sensor.

Manual “Coming home” function: the “Coming home” function is switched on manually.

The “Leaving home” function automatically controls the rain/light sensor.

The lighting time can be adjusted in the vehicle settings in the Infotainment system and the function can be activated or deactivated ⇒ Vehicle settings menu.

Switching on the automatic “Coming home” function

1. Switch the ignition off.

The “Coming home” lighting switches on automatically when the light switch is in the

The lighting time begins when the last vehicle door or trunk lid is closed.

position and the rain/light sensor detects darkness.

Switching on the manual “Coming home” function

1. Switch the ignition off.

2. Press the headlight ﬂasher.

The “Coming home” lighting switches on automatically when the driver door opens. The switch-off delay begins when the last door or the trunk lid is closed.

Switching the “Exit lighting” function off

1. Turns off automatically after the set lighting time has elapsed.

Or: Automatically if a vehicle door or the trunk lid is still open approximately 30 seconds after switching on.

Or: Switch off the light.

Or: Switch on the ignition.

Switching the “Entry lighting” function on

1. Unlock the vehicle when the automatic headlight control

is switched on and the rain/light sensor detects darkness.

Switching the “Entry lighting” function off

128

1. Turns off automatically after the lighting time has elapsed.

Or: Lock the vehicle.

Or: Switch off the light.

Or: Switch on the ignition.

Light functions

Cornering lights

If the low beam headlights are switched on, a cornering light will also switch on during slow turns or in very tight corners.

When reverse gear is engaged, the cornering lights on both sides of the vehicle will turn on automatically to better illuminate the surroundings while

maneuvering.

Automatic headlight control

If automatic headlights

are switched on, the vehicle lighting switches on and off automatically along with the instrument illumination under the following

conditions:

The light sensor has detected darkness.

The windshield wipers are switched on for a long time.

When the lights are turned on, the yellow indicator light

turns on ⇒ Switching the lights on and off .

Automatic headlight control is merely an aid and cannot always accurately detect all driving situations.

If the vehicle is equipped accordingly, the activation time of the automatic headlights can be adjusted in the vehicle settings in the Infotainment system ⇒ Vehicle

settings menu.

Headlight range control

The headlight range must always be adapted to the vehicle load level. This provides the driver with the best possible visibility and oncoming trafﬁc is not dazzled. To

ﬁnd out whether your vehicle features headlight range control, contact an authorized Volkswagen dealer or authorized Volkswagen Service Facility. Volkswagen

recommends contacting an authorized Volkswagen dealer or authorized Volkswagen Service Facility.

Without headlight range control

The beam of the low beam headlights must be adjusted by an authorized Volkswagen dealer or authorized Volkswagen Service Facility to take into account the

vehicle's load ⇒

. Volkswagen recommends contacting an authorized Volkswagen dealer or authorized Volkswagen Service Facility.

Dynamic headlight range control

The headlight range automatically adjusts to the vehicle load when the headlights are switched on ⇒

WARNING

Heavy objects in the vehicle can affect the vehicle level in such a way that causes the headlights to dazzle and distract other road users. This can cause

accidents and serious or fatal injuries.

Always adjust the light cone to the vehicle load so that other road users are not dazzled.

WARNING

If the headlight range control fails or malfunctions, the headlights may blind and distract other road users. This can cause accidents and serious or fatal injuries.

Have the headlight range control inspected immediately by an authorized Volkswagen dealer or authorized Volkswagen Service Facility. Volkswagen

recommends contacting an authorized Volkswagen dealer or authorized Volkswagen Service Facility.

Adjusting headlights (travel mode)

When traveling in countries that drive on the opposite side of the road from your home country, the asymmetric low beam headlights can dazzle oncoming trafﬁc.

Therefore, when driving in such countries, certain headlight variants must be adjusted, or certain areas of the headlight lens must be masked off. For further

information, contact an authorized Volkswagen dealer or authorized Volkswagen Service Facility. Volkswagen recommends contacting an authorized Volkswagen

dealer or authorized Volkswagen Service Facility.

Travel mode may be used only for a short period of time. Contact an authorized Volkswagen dealer or authorized Volkswagen Service Facility for permanent

conversion. Volkswagen recommends contacting an authorized Volkswagen dealer or authorized Volkswagen Service Facility.

Warning tones when lights are not turned off

If the ignition has been switched off and the driver door is opened, warning tones will sound under the following conditions:

129

With the side lights switched on

If the orientation lighting is switched on, the warning tone to indicate that the light is still turned on will not sound when leaving the vehicle ⇒ “Exit lighting” and “En

lighting” function (orientation lighting).

Interior lighting

Instrument and switch illumination

You can adjust the brightness of the instrument illumination in the vehicle settings in the Infotainment system ⇒ Vehicle settings menu.

The selected brightness will automatically adjust to the changing brightness in the vehicle.

If the automatic headlights

outside brightness.

are switched on, a sensor switches the dipped beams and the instrument and switch lighting on and off automatically based on

The instrument illumination for the needles and dials turns on when the ignition is on and the lights are off. The lighting for the gauges reduces automatically

and eventually turns off as brightness outside increases. This function should remind the driver to turn off low beam headlights at the right time, such as when

driving through tunnels.

Interior/reading lights, ambient lighting

Switching on or off interior and reading lights

The scope and the representation of the controls in the headliner vary depending on the vehicle equipment.

Press the corresponding button:

Switch off the interior lights.

Switch on the interior lights.

Switch the rear interior lights on or off.

The interior lights will switch on automatically when

unlocking or leaving the vehicle. The interior lights will switch on automatically when unlocking or leaving the vehicle.

Switch the reading lights on or off.

Glove compartment and luggage compartment lights

The glove compartment and the luggage compartment may be illuminated depending on the vehicle equipment.

The relevant light turns on or off when opening and closing the glove compartment or trunk lid.

Ambient lighting

Depending on vehicle equipment, ambient lighting can provide indirect lighting in various areas of the vehicle interior.

Other areas may also be illuminated, e.g. the footwell.

Depending on vehicle equipment, you can adjust the brightness and color of the ambient lighting in the vehicle settings in the Infotainment system ⇒ Vehicle

settings menu. If you select the setting Auto, the color of the ambient lighting changes depending on the driving mode setting.

Vehicles with a starter button: After the ignition has been switched off, the lights will turn off when the vehicle is locked or automatically after a few minutes.

This reduces the risk of the 12 V vehicle battery being drained.Vehicles with ignition lock: After the vehicle key has been removed from the ignition switch, the

lights will turn off when the vehicle is locked or automatically after several minutes. This reduces the risk of the 12 V vehicle battery being drained.

130

Lights for Your Volkswagen Tiguan 4 Door 2023

Popular Manuals