Get Visibility -> Visibility Guide for Volkswagen Tiguan 4 Door 2023

Visibility

Window wipers

Operating the windshield wiper lever

Fig. 103 On the right side of the steering column: operating the windshield wipers.

The windshield wipers only work when the ignition is switched on and the hood or trunk lid is closed. Move the wiper lever into the desired position

Wipers are switched off.

⇒

:

Interval wiping for the windshield or rain sensor mode. Interval wiping for the windshield depends on the driving speed. The higher the speed, the faster

the wipers will move.

Slow wiper speed.

Fast wiping.

One-tap wiping – brief wiping. Press and hold the lever down longer to wipe faster.

Pull the lever to activate the automatic wiper/washer system to clean the windshield. While the wiper/washer system is active, the Climatronic system

switches to recirculation mode for approximately 30 seconds to help prevent the washer fluid odor from entering the vehicle interior.

Switch for interval levels (vehicles without rain/light sensor) or to adjust the sensitivity of the rain/light sensor.

Fig. 104 On the right side of the steering column: operating the rear window wiper.

Move the wiper lever into the desired position ⇒

:

Interval wiping for the rear window. The wiper moves approximately every six seconds.

Press the lever to activate the automatic wiper/washer system to clean the rear window.

WARNING

131

Without the sufﬁcient freeze protection, washer ﬂuid can freeze on the window glass and reduce visibility. This can cause accidents and serious or fatal injuries.

Only use the washer system with sufﬁcient freeze protection in winter temperatures.

Never use the window washer system in winter temperatures if the windshield has not been warmed up with the air conditioning system.

WARNING

Worn or dirty wiper blades reduce visibility and increase the risk of accidents and serious injuries.

Always replace wiper blades if they are damaged or worn and are no longer cleaning the window glass sufﬁciently ⇒ Cleaning and changing wiper

blades.

NOTICE

Incorrect handling of the windshield wipers can cause damage to the windshield, the wiper blades and the wiper motor.

Before driving and before the ignition is switched on, check that the windshield wiper lever is in the basic position.

Remove any snow and ice from the windshield wipers and the windshield.

Always carefully loosen wiper blades that have frozen onto the windshield from the windshield.

Do not turn on the windshield wipers when the windshield is dry.

The activated wiper speed temporarily changes to the next lower speed when the vehicle is stationary.

When parking the vehicle in cold weather conditions, moving the windshield wipers to the service position may be helpful for loosening the wiper blades more

easily from the windshield ⇒ Putting the windshield wipers in the service position .

Wiper function

Automatic rear window wiping

The rear window wiper switches on automatically when the windshield wipers are switched on and reverse gear is engaged. The automatic activation in reverse

gear function can be activated and deactivated in the vehicle settings in the Infotainment system ⇒ Vehicle settings menu.

Heated washer nozzles

The heat thaws frozen washer ﬂuid nozzles. The heat output is automatically regulated when the ignition is switched on and is dependent on the outside

temperature. Only the window washer nozzles are heated and not the washer ﬂuid hoses.

Heated windshield wiper area

If the windshield wipers are in starting position, they can be heated when the temperature is approx. +4 °C (approx. +39 °F) or lower, depending on the vehicle

equipment. The function is switched on automatically as soon as you switch on the defrost function or the rear window defroster, or you start the vehicle via the

remote start relay function. If the vehicle is moved or the windshield wipers have become heated after a few minutes, then the function switches off automatically.

Rain/light sensor

Fig. 105 On the right side of the steering column: windshield wiper lever.

Switch for adjusting the sensitivity of the rain/light sensor.

Rain/light sensor deactivated.

132

Rain/light sensor activated, automatic wiping as necessary.

When switched on, the rain/light sensor automatically shortens or lengthens the delay between wiping cycles depending on how hard it is raining.

Activating and deactivating the rain/light sensor

1. Press the lever into the desired position ﬁg. 105.

Automatic wiping can be activated and deactivated in the vehicle settings in the Infotainment system ⇒ Vehicle settings menu.

If automatic wiping is deactivated in the Infotainment system, the interval time will be set in ﬁxed stages.

Adjusting the sensitivity of the rain/light sensor

The sensitivity of the rain/light sensor can be manually adjusted with the switch in the windshield wiper lever ﬁg. 105 , ⇒

Move the switch to the right – high sensitivity.

.

Move the switch to the left – low sensitivity.

WARNING

The rain/light sensor cannot detect all precipitation sufﬁciently and activate the windshield wipers accordingly. Reduced visibility can cause accidents and

serious or fatal injuries.

If necessary, switch on the windshield wipers manually if water on the windshield is impairing visibility.

Troubleshooting

Washer ﬂuid level too low

The yellow indicator light turns on.

1. Fill the washer ﬂuid reservoir ⇒ Washer ﬂuid.

Windshield wiper malfunction

The yellow indicator light turns on.

The windshield wipers are not working.

1. Switch the ignition off and on.

2. If the malfunction persists, contact a suitably qualiﬁed professional. Volkswagen recommends contacting an authorized Volkswagen dealer or authorized

Volkswagen Service Facility.

Rain/light sensor malfunction

The yellow indicator light turns on.

The windshield wipers will not be automatically activated in rain/light sensor mode when it is raining.

1. Switch the ignition off and on.

2. If the malfunction persists, contact a suitably qualiﬁed professional. Volkswagen recommends contacting an authorized Volkswagen dealer or authorized

Volkswagen Service Facility.

Changes to rain/light sensor reaction

Some possible reasons for malfunctions and misinterpretations in the sensor area of the rain/light sensor ⇒ View from the front could be:

Damaged wiper blades: damaged wiper blades can leave a ﬁlm of water or streaks on the window, and this can extend the activation time, greatly shorten the

wiper intervals, or cause fast wiping time.

Insects: insects hitting the windshield may trigger the wipers.

Salt streaks: salt streaks on the windshield from driving in the winter can cause the wipers to wipe more frequently or continuously on a window that is almost

dry.

Dirt: dried dust, wax, any other build-up on the windshield (lotus effect), or washing product residue (car wash) can lower the sensitivity of the rain/light sensor

and cause it to react too slowly or not at all. Clean the sensor area for the rain/light sensor regularly and check the wiper blades for damage ⇒ Exterior care

and cleaning.

Crack in the windshield: if a stone strikes and chips the sensor area while the rain/light sensor is on, this will trigger a wiper cycle. After that, the rain/light

sensor will detect this irregularity on the sensor surface and react to it. Depending on the size of the chip, the reaction behavior of the rain/light sensor may or

may not change.

If there is an obstacle for the wipers on the window glass, the wipers will attempt to remove it. If it continues to block the wipers, the wipers will stop moving.

1. Remove the obstacle and switch the wipers on again.

133

Mirrors

General safety precautions

Using the outside mirrors and the interior rearview mirror, the driver can observe trafﬁc and adjust their driving based on trafﬁc.

For driving safety, it is important that the driver adjusts the outside mirrors and the interior rearview mirror correctly before starting to drive.

It is not possible to oversee the entire side and rear area of the vehicle by looking in the outside and interior rearview mirrors. These areas that are not visible are

called blind spots. Other road users and objects could be in the blind spot.

WARNING

Adjusting the outside mirrors and interior rearview mirror while driving can distract the driver. This can cause accidents and serious or fatal injuries.

Only adjust the outside mirror and interior rearview mirror when the vehicle is stationary.

Always make sure that the mirrors are adjusted correctly and visibility to the rear is not limited by ice, snow, fog, or other objects.

WARNING

The view in the outside mirrors and interior rearview mirror does not cover the entire area around the side and rear of the vehicle. Other road users and objects

could be in these blind spots. This can cause accidents and serious or fatal injuries.

When parking, changing lanes, passing, and turning, always pay attention to your surroundings.

WARNING

Curved mirror surfaces (convex or aspheric) enlarge the ﬁeld of vision and allow objects in the mirror to appear smaller and farther away. This can make it

difﬁcult to estimate the exact distance from the vehicles behind, e.g. when changing lane. This can cause accidents and serious or fatal injuries.

Use the interior rearview mirror as much as possible to more accurately determine the distance to vehicles or other objects behind you.

Make sure there is sufﬁcient visibility of the area behind the vehicle.

WARNING

An automatic dimming rearview mirror contains an electrolyte ﬂuid that can leak out if the mirror glass breaks. Coming into contact with this liquid can irritate the

skin, eyes, and respiratory organs, especially in individuals with asthma or similar illnesses. This may cause serious injuries.

If electrolyte ﬂuid is swallowed, rinse out the mouth immediately for at least 15 minutes with plenty of water. Do not induce vomiting unless it ordered to

do so by a doctor. Call for medical assistance immediately.

Immediately get plenty of fresh air and exit the vehicle. If this is not possible, open all the windows and doors.

If the electrolyte ﬂuid comes into contact with eyes or skin, wash the affected area immediately for at least 15 minutes with plenty of water and seek

medical assistance.

If the electrolyte ﬂuid comes into contact with your shoes or clothing, wash it for at least 15 minutes with plenty of water. Clean the shoes and clothing

thoroughly before wearing them again.

NOTICE

If the glass on an automatic dimming mirror breaks, electrolyte ﬂuid can leak out. This ﬂuid damages plastic surfaces.

Remove any leaking ﬂuid as soon as possible, for instance using a wet sponge.

Interior rearview mirror

134

Fig. 106 On the windshield: automatic dimming interior rearview mirror.

Sensor for light entering from the rear.

Sensor for light entering from the front.

Fig. 107 On the windshield: manual dimming interior rearview mirror.

Automatic dimming interior rearview mirror

When the ignition is on, the sensors measure the amount of light entering from the rear ﬁg. 106

Depending on the measured values, the interior rearview mirror will dim automatically.

and from the front

.

If the amount of light entering the sensors is limited or interrupted, for example by a sunshade or attachment, the automatic dimming interior rearview mirror may no

function or may malfunction. Mobile navigation devices on the windshield or near the automatic dimming interior rearview mirror can also affect the sensors ⇒

.

Automatic dimming will be deactivated in some situations, for example when reverse gear is engaged.

135

Manual dimming interior rearview mirror

Base position: lever on the lower edge of the mirror points forward toward the windshield.

To dim, pull the lever back ﬁg. 107.

WARNING

The illuminated display of a mobile navigation system may interfere with the automatic dimming interior rearview mirror. This may stop you from using the

interior rearview mirror to accurately determine the distance from vehicles or other objects behind you. Accidents and serious or fatal injuries could result.

Switch the mobile navigation system off in such cases.

Outside mirrors

Fig. 108 In the driver door: knob for the outside mirrors.

The following information describes the outside mirror functions for left-hand drive vehicles. Position corresponds to the outside mirror on the driver's side, and

position corresponds to the outside mirror on the passenger's side. For right-hand drive vehicles, proceed in the reverse order.

Adjusting outside mirrors

1. Switch the ignition on.

2. Turn the knob in the driver door to the preferred symbol ﬁg. 108.

3. To adjust the outside mirror, push the knob forward, back, right or left in the direction of the arrow.

Fold the outside mirror in towards the vehicle body ⇒

.

Switch on the outside mirror heating. The exterior mirror heating only works when the ambient temperature is below approx. 20 °C (around 68 °F) and

provides the most heat when it first turns on. After about two minutes, the mirrors will be heated depending on the ambient temperature.

Adjusts the left outside mirror.

Adjusts the right outside mirror.

Neutral position. The outside mirror cannot be adjusted and all functions are switched off.

Activating outside mirror functions

The following outside mirror functions must be activated in the vehicle settings in the Infotainment system before they are used for the ﬁrst time ⇒ Vehicle settings

menu.

Synchronized mirror adjustment

The synchronized mirror adjustment feature simultaneously adjusts the right-side outside mirror to match adjustments to the left-side outside mirror.

1. Turn rotary knob to position

.

2. Adjusts the left outside mirror. The right outside mirror will be adjusted the same way (synchronized).

3. To correct the adjustment of the right outside mirror, if necessary, turn the knob to the

position and adjust the right outside mirror.

Folding the outside mirrors in while parking

If the vehicle is locked or unlocked from the outside, the outside mirrors will automatically fold in or out. For this to happen, the knob must be in the

,

or

136

position.

If the knob for power exterior mirrors is in the

position, the outside mirrors will remain folded in.

Save the passenger-side outside mirror settings when reversing

1. Unlock the vehicle using the key, to which the setting is allocated.

2. Set the electronic parking brake.

3. Switch the ignition on.

4. Shift the transmission to neutral.

5. Select the reverse gear.

6. Adjust the front passenger outside mirror so that, for example, the edge of the curb can be seen clearly.

7. Shift the transmission to neutral.

8. Switch the ignition off.

The selected mirror position will be stored and assigned to the vehicle key.

Opening the front passenger outside mirror settings for driving in reverse

1. Turn rotary knob for the outside mirrors to the relevant position for adjusting the front passenger outside mirror.

2. With the ignition switched on, select reverse gear.

The front passenger outside mirror will adjust to the stored position.

The front passenger outside mirror will exit the position stored for driving in reverse when you begin driving forward faster than about 15 km/h (about 9 mph) or whe

the knob is turned to any other position.

WARNING

If you fold the outside mirrors against the vehicle or back without taking care, you could get your ﬁngers jammed between the outside mirror and the mirror

base. This can cause serious injuries.

Do not fold the outside mirrors out or in if there are any obstacles in the path.

NOTICE

If outside mirrors are not folded in when driving through a car wash, they can get damaged.

Always fold in the outside mirrors.

NOTICE

Folding in the power exterior mirror manually can worsen wear and tear or damage the mirror motor.

Do not fold power exterior mirrors in or out by hand.

Leave the outside mirror heating on only as long as it is needed. Otherwise fuel will be used unnecessarily.

If there is a malfunction in the power outside mirror, you can adjust the position of the mirror manually by hand by pushing on the edge of the mirror surface.

Sunshade

Sun visors

137

Fig. 109 In the front of the headliner: sun visor.

Light.

Remove from holder.

Slide cover open.

Adjustment options for the driver and front passenger sun visors:

Fold toward the windshield.

Remove from the holder and tilt toward the door ﬁg. 109.

Illuminated vanity mirror

When the sun visor is folded down, there is a vanity mirror located behind a cover. The lights ﬁg. 109 turn on when the cover ﬁg. 109 slides open.

WARNING

Visibility may be reduced when sun visors are folded down and the sunshades are extended. This can cause accidents and serious or fatal injuries.

Always guide sun visors and sunshades back into their holders when they are no longer needed.

Under certain conditions, the light above the sun visor will turn off automatically after several minutes. This reduces the risk of the 12 V vehicle battery being

drained.

Sunshade in the sunroof

Fig. 110 In the headliner: buttons for controlling the sunshade.

Button for opening the sunshade.

Button for closing the sunshade.

The power sunshade only works when the ignition is switched on.

When the sunroof is tilted all the way open, the sunshade automatically moves into a position that provides ventilation. The sunshade will remain in the ventilation

position after the sunroof is closed.

The ﬁg. 110 and

buttons have two detents. In the ﬁrst detent, the sunshade can be opened or closed either completely or partially.

138

In the second detent, pressing the button brieﬂy opens or closes the sunshade completely. Pressing the button again stops the one-touch feature.

Opening the sunshade

1. Press the

button to the ﬁrst level.

Automatic process: Press the

button brieﬂy to the second level.

2. To interrupt the automatic opening process, press the button

again brieﬂy.

Closing the sunshade

1. Press the

button to the ﬁrst level.

Automatic process: Press the

button brieﬂy to the second level.

2. To interrupt the automatic closing process, press the button

again brieﬂy.

The sunshade can still be opened or closed for several minutes after the ignition has been switched off, as long as the driver’s or front passenger door has not been

opened.

Sunshade pinch protection

The pinch protection can reduce the risk of being pinched and injured when the sunshade is closing

when closing, the sunroof or sunshade will open again immediately.

⇒

. If the sunshade encounters resistance or an obstacle

1. Check why the sunroof did not close.

2. Try again to close the sunshade.

If the sunshade still encounters resistance or an obstacle and will not close, open the sunshade again. Within a short time after opening, you can close the

sunshade again without pinch protection.

3. If the sunshade is still not able to close, close the sunshade without pinch protection.

Closing the sunshade without pinch protection

1. Within approximately ﬁve seconds after pinch protection is triggered, press and hold the ﬁg. 110 button until the sunshade is completely closed.

This will close the sunshade without pinch protection.

2. If the sunshade still will not close, contact an authorized Volkswagen dealer or authorized Volkswagen Service Facility for assistance. Volkswagen recommends

contacting an authorized Volkswagen dealer or authorized Volkswagen Service Facility.

WARNING

Closing the sunshade without pinch protection may result in serious injuries.

Always be careful when closing the sunshade.

Ensure that nobody is within the range of operation of the sunshade, especially if it is closing without pinch protection.

When the sunroof is open, the power sunshade can only be closed to the front edge of the sunroof.

Windshield with communication window

Fig. 111 Next to the mirror base: Communication window (general example).

Windshields made of heat protection glass may have an infrared-reﬂecting coating and may, depending on the vehicle equipment, be able to be wirelessly heated.

In order to ensure that wireless equipment from the accessories industry, e.g. toll systems, can function correctly, an uncoated area is present on either side of the

interior rearview mirror (communication window) ﬁg. 111.

139

The uncoated areas must not be covered from the inside or outside, or have stickers on them, because this could cause malfunctions.

140

Visibility -> Visibility for Your Volkswagen Tiguan 4 Door 2023

Popular Manuals